Mpow Flame Lite TWS Earbuds User Manual BH452A

USER MANUAL

Mpow Flame Lite TWS

TWS Earbuds
Mpow Flame Lite / BH452A

PACKING LIST

PACKING LIST

DIAGRAM

DIAGRAM

POWER ON

Model 1 (Auto)
  1. The earphones automatically turn on(with white LED l ight flashing} and start pairing when you open the charging case.
  2. In the shutdown status and when the earphones are not in the charging case, simultaneously press and hold the MFB of both earbuds for 2 seconds to power on ( with the white LED light fishing).

POWER OFF

POWER OFF
  1. Put the earphones back In the charging case and c lose the case to tum them off.
  2. If the earphones are not in the charging case. just press and hold the MFB of both earbuds for 5 seconds ID power them off. (Mode 2 ran not be conducted during music playing or calling.

PAIRING

PAIRING
PAIRING
  1. Open the charging case, they will automatically enter< the pairing mode in which the LED light flashes white and red alternately. and then .select “MJXM’ Flame Lite”.
  2. Manually switch to Pairing Mode, keep both earbuds in the charging case and open the case. then press and hold the button on the charging case for 3 seconds, It will re-<enter into pairing mode in which LED flash red and white alternately. Finally select ‘Mpow Flame Lite”on your device to pair.
MUSIC

INCOMING CALL

INCOMING CALL

MUSIC & INCOMING CALL & Siri

Volume Up/ Down
Volume+: press and hold the MFS button of Right (R) <) earbud to turn up the Volume increasingly.
Volume-: press and hold the MFB button of Left~ earbud to turn down the volume decreasingly.

Next I Previous Track
Next Track: double tap the MFB of Right (R) earbud.
Previous Track: double tap the MFB of Left (L) earbud.

Play/ Pause
Tap the MFB of either earbud Once

•Answer /Hang Up
Double tap the MFB of either earbud.

Reject
Press and hold the MFB of either earbud for 2 seconds.

Activate Siri
Triple-tap the MFB of either earbud.

RESET

RESET
  1. Keep both earbuds in the charging case.(with the charging case opened)
  2. Press and Hold the button on the charging case for 6 seconds to clear all paired information.
  3. The earbuds will flash red and white 3 times. which means successful resetting.
  4. The LED light will go out for 1 second and then Mpow Flame Lite will automagically re-enter into pairing mode.

CHARGING

CHARGING

Do not put the earbuds in the charging case when the earbuds are wet.

CORRECT DISPOSAL OF THIS PRODUCT

(Waste Electrical & Electronic Equipment )

Disposal

This Marking shown on this product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.

To prevent possible harm to the environment or human health from unconlroll9d waste disposal please separate this from other type of waste and recycle it responsibly to promote the sustainable reuse of material resources. Household user should contact either the retailer where they purchased this product. or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contact This product should not be mixed with other commercial wastes for disposal.

FCC STATEMENT

Any Changes or modifications not expressly approved by the party responsible for compliance could void the use’s authority to operate the equipment . This device compiles with part 15 of the FCC Rules Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

2) This device must accept any interference received. including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment compiles with FCC radiation exposure limits set forth for an uncontrolled environment .

Questions about your Manual? Post in the comments!

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. I got them 2 days ago, I put them into their charging case for charging. So, when I using them, the right one after 15 minutes decide to turn off by itself while the left keeps playing>>

    Rodrigo Gonzalez asks I got them 2 days ago, I put them into their charging case for charging. So, when I using them, the right one after 15 minutes decide to turn off by itself while the left keeps playing>>
    Manuals+ clarified question
    Question

    Why does my right Mpow Flame Lite earbud turn off by itself after 15 minutes while the left one stays on?

    Answer

    It sounds like your right earbud may have a charging connection issue or a synchronization error. Please try the following troubleshooting steps to resolve the issue:

    • Clean the Charging Pins: Use a dry cotton swab or a cloth with a small amount of rubbing alcohol to clean the metal charging contacts on both the right earbud and inside the charging case. Debris or oils can prevent a full charge.
    • Perform a Reset: To reset your Mpow Flame Lite, place both earbuds in the charging case and keep the case open. Press and hold the button on the charging case for about 10 seconds. The LED should flash, indicating the reset is complete.
    • Check for Mono Mode: Ensure the earbud isn't accidentally being powered off by a long press on the MFB (Multi-Function Button). If the earbud is not in the case, holding the MFB for 5 seconds will turn it off.
    • Verify Charging: When you place the right earbud in the case, ensure the LED light turns on to indicate it is actually charging. If it doesn't light up, the earbud may not have been charged during those 2 days.

    If the right earbud continues to shut down after 15 minutes despite a full charge and a reset, it may have a defective battery.

    1. Discharge-charge several times. The battery charges should equalize.
      Несколько раз разрядить-зарядить. Должны выровняться заряды аккумуляторов.

      Евгений asks <em>Discharge-charge several times. The battery charges should equalize.<e/em>
      Несколько раз разрядить-зарядить. Должны выровняться заряды аккумуляторов.
      Manuals+ clarified question
      Question

      Why does my right Mpow Flame Lite earbud turn off by itself after 15 minutes while the left one stays on?

      Answer

      Discharge-charge several times. The battery charges should equalize.
      Несколько раз разрядить-зарядить. Должны выровняться заряды аккумуляторов.

  2. Onyl two Months old and one is working fine the other is making a ring ring sound and then nothing in the left ear bud!

    Declan McCaughey asks Onyl two Months old and one is working fine the other is making a ring ring sound and then nothing in the left ear bud!
    Manuals+ clarified question
    Question

    Why is my left earbud making a ringing sound and then failing to produce audio?

    Answer

    If your left earbud is making a ringing sound and then going silent, it may be experiencing a synchronization or power issue. Please try the following troubleshooting steps to reset the connection:

    • Reset the Earbuds: Place both earbuds back into the charging case. Keep the case open, then press and hold the button on the charging case for about 3 to 10 seconds until the LED indicators flash. This will reset the pairing information.
    • Check for Low Battery: Ensure the left earbud is making proper contact with the charging pins in the case. A ringing or beeping sound can sometimes indicate a low battery warning before the unit powers off.
    • Clean the Charging Contacts: Use a dry cotton swab to clean the gold contacts on the earbud and the pins inside the case to ensure it is charging correctly.
    • Manual Power On: If the earbud does not turn on automatically when removed from the case, press and hold the MFB (Multi-Function Button) on the left earbud for 2 seconds.

    If the ringing sound persists after a full reset and charge, the earbud may have a hardware defect. Since your device is only two months old, it should still be under warranty; we recommend contacting Mpow support or the retailer for a replacement.

    1. I had the same problem! I just put both headphones in the case, pressed the button on the back of the charging case for six seconds to reset it – and when I paired them again – it was fixed!

      Hope this helps.

      Matt asks I had the same problem! I just put both headphones in the case, pressed the button on the back of the charging case for six seconds to reset it - and when I paired them again - it was fixed!

      Hope this helps.

      Manuals+ clarified question
      Question

      Why is my left earbud making a ringing sound and then failing to produce audio?

      Answer

      I had the same problem! I just put both headphones in the case, pressed the button on the back of the charging case for six seconds to reset it - and when I paired them again - it was fixed!

      Hope this helps.

  3. Hi – got these as a present at Xmas from a friend.
    Initially had problems pairing – took half an hour or trying before they finally paired (Galaxy A7 phone).
    Then recently the right one switched off and won’t respond to any inputs on the MFB so effectively dead, and the Left ear piece now refuses to link to the phone.
    Very disappointed and not been used much.
    Please contact me for a replacement.

    Mike Waddell asks Hi - got these as a present at Xmas from a friend.
    Initially had problems pairing - took half an hour or trying before they finally paired (Galaxy A7 phone).
    Then recently the right one switched off and won't respond to any inputs on the MFB so effectively dead, and the Left ear piece now refuses to link to the phone.
    Very disappointed and not been used much.
    Please contact me for a replacement.
    Manuals+ clarified question
    Question

    How do I fix pairing issues and an unresponsive right earbud on my Mpow Flame Lite BH452A?

    Answer

    To resolve issues where one earbud is unresponsive or the set will not pair, you should perform a factory reset. Please follow these steps:

    1. Turn off Bluetooth: Disable Bluetooth on your Galaxy A7 and 'Forget' or 'Delete' Mpow Flame Lite from your paired devices list.
    2. Place in Case: Put both earbuds into the charging case.
    3. Reset: Keep the charging case open, then press and hold the button on the charging case for 10 seconds. The LED light on the case will flash, indicating the reset is complete.
    4. Re-pair: Close and then reopen the case. The earbuds should enter pairing mode (flashing red and white). Turn Bluetooth back on your phone and select 'Mpow Flame Lite'.

    If the right earbud still does not respond to the MFB or show any lights, ensure the charging pins inside the case and on the earbud are clean and free of debris. Regarding your request for a replacement, please note that Manuals+ provides instructional support and is not the manufacturer or retailer. You will need to contact Mpow support or the original gift-giver for warranty claims.

  4. I am having similar problems as the comments above.
    My left bud turns off after 15 minutes.
    I’ve re-charged, re-set, and re-paired.
    I’d like a refund. Would have asked for a replacement, but looks like there’s an issue with these.

    Nancy Lee Hardy asks I am having similar problems as the comments above.
    My left bud turns off after 15 minutes.
    I've re-charged, re-set, and re-paired.
    I'd like a refund. Would have asked for a replacement, but looks like there's an issue with these.
    Manuals+ clarified question
    Question

    Why does my left Mpow Flame Lite earbud turn off after 15 minutes even after resetting and recharging?

    Answer

    It appears you have already performed the standard troubleshooting steps (recharging, resetting, and re-pairing) for the Mpow Flame Lite (BH452A). If the left earbud continues to power off after 15 minutes, it likely indicates a hardware defect or a failing battery cell in that specific unit.

    Since Manuals+ provides product documentation and is not the manufacturer or retailer, we cannot process refunds directly. To obtain a refund or exercise your warranty, you should:

    • Contact the Seller: Reach out to the store or online platform (e.g., Amazon, Walmart) where you purchased the earbuds. Most platforms have a 30-day return window.
    • Contact Mpow Support: If you are outside the retailer's return window, check your original packaging or the Mpow website for warranty support. You will typically need your order ID and proof of purchase.

    If you haven't already, ensure the charging pins inside the case and on the left earbud are clean and free of debris, as a poor connection can sometimes lead to an incomplete charge that mimics a shutdown issue.

  5. Stupid things just won’t charge, very disappointed. And similar problems as above…

    Ray M asks Stupid things just won't charge, very disappointed. And similar problems as above...
    Manuals+ clarified question
    Question

    Why are my Mpow Flame Lite TWS earbuds not charging?

    Answer

    If your Mpow Flame Lite earbuds are not charging, please try the following troubleshooting steps:

    • Clean the Charging Contacts: Use a dry cotton swab or a cloth with a small amount of rubbing alcohol to clean the metal charging pins on the earbuds and the pins inside the charging case. Dust or sweat buildup can prevent a proper connection.
    • Check the Cable and Power Source: Ensure the USB-C charging cable is securely plugged into both the case and a functional power source (such as a wall charger or computer). Try using a different cable or charger to rule out a cable fault.
    • Reset the Earbuds: If the earbuds are unresponsive, place both earbuds in the charging case, keep the case open, and press and hold the button on the charging case for 3 to 5 seconds until the LED indicators flash.
    • Verify Placement: Ensure the earbuds are seated correctly in the case and that the case lid is fully closed.

    If the LED lights on the case do not illuminate when plugged in, the charging case itself may be defective.

  6. Left earbud no longer works. I have tried to reset. I have tried to pair again but no luck. Is there a recurring problem that manufacturing has failed to address???

    joseph penna asks Left earbud no longer works. I have tried to reset. I have tried to pair again but no luck. Is there a recurring problem that manufacturing has failed to address???
    Manuals+ clarified question
    Question

    My left earbud is not working despite attempting a reset and re-pairing. Is this a known manufacturing issue?

    Answer

    If your left earbud is not working after a standard reset, please ensure you have followed the specific hardware reset procedure for the Mpow Flame Lite (BH452A):

    1. Turn off your device's Bluetooth and delete the pairing record for "Mpow Flame Lite".
    2. Place both earbuds into the charging case.
    3. Keep the charging case open, then press and hold the button on the charging case for 10 seconds.
    4. The LED light on the case should flash, indicating the reset is complete.

    If the left earbud still shows no signs of power (no LED lights when opening the case or pressing the MFB), check the charging pins inside the case and on the earbud for debris or oxidation. Clean them gently with a cotton swab and rubbing alcohol. Regarding manufacturing issues, while individual units may fail, there is no official recall or publicly documented recurring manufacturing defect for this model; however, if the hardware remains unresponsive after cleaning and resetting, the unit may have a hardware failure covered under warranty.

  7. What a surprise, left earbud ceased working :\

    Lie G asks What a surprise, left earbud ceased working :\
    Manuals+ clarified question
    Question

    How do I fix the left earbud of my Mpow Flame Lite if it has stopped working?

    Answer

    If your left earbud has stopped working, it may be due to a sync issue or a power failure. Please try the following troubleshooting steps:

    • Check for Power: Place the left earbud back into the charging case and ensure the charging pins are clean and making contact. Look for a LED light indicator to confirm it is charging.
    • Manual Power On: If the earbud is out of the case and off, press and hold the Multi-Function Button (MFB) on the left earbud for 2 seconds until the white LED flashes.
    • Reset the Connection: To resync the earbuds, place both earbuds back into the charging case and keep the case open. Press and hold the button on the charging case for 3 seconds to re-enter pairing mode.
    • Clean the Contacts: Use a dry cotton swab to clean the charging contacts on both the earbud and inside the case to ensure the earbud is receiving power.

    If the earbud still does not respond after these steps, it may indicate a hardware failure.

  8. Am having trouble getting them to work; purchased couple months ago; tried several times ; unable to get them working!

    Anonymous asks Am having trouble getting them to work; purchased couple months ago; tried several times ; unable to get them working!
    Manuals+ clarified question
    Question

    How do I troubleshoot and get my Mpow Flame Lite TWS earbuds to work?

    Answer

    To get your Mpow Flame Lite earbuds working, please follow these steps to ensure they are powered on and correctly paired:

    • Powering On: Open the charging case; the earbuds should automatically turn on (white LED will flash). If they are outside the case and off, press and hold the Multi-Function Button (MFB) on both earbuds for 2 seconds.
    • Pairing Mode: Open the charging case. The LED lights should flash white and red alternately. On your device, look for and select "Mpow Flame Lite" in the Bluetooth settings.
    • Manual Pairing: If they do not appear on your device, place both earbuds in the charging case and keep the case open. Press and hold the button on the charging case for 3 seconds to re-enter pairing mode.
    • Resetting: If the earbuds still do not work, ensure they are charged. You can also try a reset by turning off your device's Bluetooth, placing the earbuds in the case, and following the manual pairing steps above to refresh the connection.

    If the LEDs do not light up at all when opening the case or pressing the buttons, ensure the charging case is charged using the provided USB-C cable and that any protective film on the earbud charging pins has been removed.

  9. The left earbud only holds its charge for fifteen minutes approx. Is it possible to get a replacement please?

    Simon Corteling asks The left earbud only holds its charge for fifteen minutes approx. Is it possible to get a replacement please?
    Manuals+ clarified question
    Question

    The left earbud only holds a charge for about fifteen minutes. Can I get a replacement?

    Answer

    Manuals.plus is a repository for product manuals and does not provide direct replacements or warranty services. To request a replacement for your Mpow Flame Lite (BH452A) earbuds, you should contact the retailer where you purchased them or reach out to Mpow's official customer support directly.

    Before seeking a replacement, you may want to try cleaning the charging pins on both the left earbud and inside the charging case with a dry cotton swab to ensure a solid connection. You can also try a factory reset by placing both earbuds in the charging case, keeping the case open, and holding the button on the charging case for 3 to 5 seconds until the lights flash, which may resolve some charging calibration issues.

  10. I bought them just few months ago, they were perfectly working, one day I tried to use them but one of them didn’t seem to turn on, nor even its intermiten light. So far, I’ve tried everything that could be done, firstly I thought it was out of battery, but I let them charge, guess what it didn’t work. I feel very disappointed, how can you sell such as horrible product.

    Daniel asks I bought them just few months ago, they were perfectly working, one day I tried to use them but one of them didn’t seem to turn on, nor even its intermiten light. So far, I’ve tried everything that could be done, firstly I thought it was out of battery, but I let them charge, guess what it didn’t work. I feel very disappointed, how can you sell such as horrible product.
    Manuals+ clarified question
    Question

    Why is one of my Mpow Flame Lite earbuds not turning on or charging?

    Answer

    If one of your Mpow Flame Lite earbuds is not turning on or showing a light, please try the following troubleshooting steps:

    • Clean the Charging Contacts: Use a cotton swab with a small amount of rubbing alcohol to clean the metal charging pins on the earbud and the pins inside the charging case. Dust or earwax can prevent a proper connection.
    • Manual Power On: If the earbud does not turn on automatically when the case is opened, try to power it on manually. While the earbud is out of the case, press and hold the Multi-Function Button (MFB) for 2 seconds.
    • Reset the Earbuds: To resolve potential software glitches, place both earbuds in the charging case and keep the case open. Press and hold the button on the charging case for 3 to 5 seconds until the LED light flashes. This will reset the pairing and power settings.
    • Check the Case Battery: Ensure the charging case itself is fully charged, as a depleted case will not trigger the earbuds to turn on or charge.

    If the LED light still does not flash white or red after these steps, the internal battery or circuitry of that specific earbud may have failed.

  11. Mit den koppeln hatte ich keine propleme obwohl ich verschiedenen player benutze. Aber beim aufladen !
    Deshalb lade ich sie einzeln auf, dann werden beide zu100% voll geladen. Den Ladezustand kann ich bei meinem Samsung H. ja sehen. 🙂 Und wen einer mal RingRing macht, kann mann das auch wie schon erwähnt, mit der Rückstelltaste wieder beheben. Den eines muss man klar sagen…der Klang/Basse sind sie sehr gut!

    Anonymous asks Mit den koppeln hatte ich keine propleme obwohl ich verschiedenen player benutze. Aber beim aufladen !
    Deshalb lade ich sie einzeln auf, dann werden beide zu100% voll geladen. Den Ladezustand kann ich bei meinem Samsung H. ja sehen. :-) Und wen einer mal RingRing macht, kann mann das auch wie schon erwähnt, mit der Rückstelltaste wieder beheben. Den eines muss man klar sagen...der Klang/Basse sind sie sehr gut!
    Manuals+ clarified question
    Question

    How can I resolve charging issues where both earbuds do not reach 100% charge simultaneously?

    Answer

    If you are experiencing issues where both earbuds do not charge to 100% simultaneously, you can follow these troubleshooting steps based on the manual and user feedback:

    • Individual Charging: As you noted, charging the earbuds one at a time in the case can ensure each reaches a full 100% charge if the case is struggling to balance both.
    • Resetting the Earbuds: If the earbuds are not syncing correctly or showing incorrect battery status, place both earbuds in the charging case, keep the case open, and press and hold the button on the charging case for 3 to 5 seconds until the indicator lights flash. This resets the connection and can resolve charging logic errors.
    • Clean Charging Pins: Ensure the copper charging pins on the earbuds and the contact pins inside the charging case are clean and free of debris or sweat, as this often prevents a full charge.
    • Power Off: Ensure the earbuds are properly seated; they should automatically power off (LED turns red) when placed in the case and the lid is closed.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.