Summerwind SWT0002 RF Remote User Manual

Summerwind-logo

Summerwind SWT0002 RF Remote

Summerwind SWT0002 RF Remote-product

Product Information

This product is a fan and light control device that comes with the following features:

  • Three-speed options for the fan
  • On/Off button for the fan
  • On/Off button for the light
  • Dimming function for the light
  • Timing function for the light
  • On/Off button for both the fan and light
  • Color-changing function for the light
  • Pairing function with the receiver

Product Usage Instructions

To use this product, please follow these instructions:

  1. Select the desired speed option for the fan using the one-speed, two-speed, or three-speed buttons.
  2. Turn the fan on or off using the On/Off button.
  3. To turn the light on or off, press and release the button.
  4. To dim the lamp, press the button once.
  5. To start the timing function, press the button once.
  6. To turn both the fan and the light on or off, press the button once.
  7. To change the light color, press the button once.
  8. To pair with the receiver, keep pressing the button until pairing is complete.
    Please note that any changes to the antenna or device are not permitted and could result in voiding your authority to operate the device. Modifying the product without approval could also void your authority to operate it. Please comply with all FCC RF exposure compliance requirements.

FUNCTIONS

  1. Summerwind SWT0002 RF Remote-fig1One speed Two speed Three speed
  2. Summerwind SWT0002 RF Remote-fig2Button: This button turns the fan On or off.
  3. Summerwind SWT0002 RF Remote-fig3The Press and release the button to turn the light ON OFF
  4. Summerwind SWT0002 RF Remote-fig4Press this button to dim the lamp
  5. Summerwind SWT0002 RF Remote-fig5Press this button to start the timing function
  6. Summerwind SWT0002 RF Remote-fig6Press this button to turn the fan and light on/off
  7. Summerwind SWT0002 RF Remote-fig7Press this button to change the light color.
  8. Summerwind SWT0002 RF Remote-fig8Keep pressing this button to pair with the receiver

IMPORTANT NOTE

To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.  Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
This device complies with Industry Canada RSS for license-free radio equipment. Operation is allowed under the following two conditions: (1) the equipment shall not produce interference, and (2) the equipment used must accept any radio interference, even if the interference may endanger the operation of the equipment. The term “IC:” before the radio certification number only signifies that Industry Canada’s Technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Documents / Resources

PDF thumbnailSWT0002 RF Remote
User Manual · 2A767-SWT0002, 2A767SWT0002, swt0002, SWT0002 RF Remote, SWT0002, RF Remote, Remote

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. who do you change the frequency on the fan the remote is Model DL-4112T-01

    greg kane asks who do you change the frequency on the fan the remote is Model DL-4112T-01
    Manuals+ clarified question
    Question

    How do I change the frequency or pair the DL-4112T-01 remote with the fan?

    Answer

    Based on the Summerwind SWT0002 manual, modern RF remotes like the DL-4112T-01 typically use a pairing process rather than manual frequency dip switches to sync with the fan receiver.

    To pair the remote with the receiver, follow these steps:

    1. Locate the LEARN button on your remote (this is often found inside the battery compartment or is a specific button on the face of the remote, labeled as item #8 in the manual diagram).
    2. Turn on the power to the fan.
    3. Within a short window after turning on the power (usually 30 seconds), keep pressing the LEARN button to pair it with the receiver.

    If your specific model has physical dip switches inside the battery compartment, you must ensure the switches on both the remote and the receiver (located on the fan motor assembly) match exactly. However, the provided documentation emphasizes the use of the pairing button for synchronization.

  2. Have a summer wind ceiling fan. Have had it for 1 and a half year. It has stopped working. No power no light. Remote still showing red light. We have checked the breaker. What could be wrong

    Dennis Gay asks Have a summer wind ceiling fan. Have had it for 1 and a half year. It has stopped working. No power no light. Remote still showing red light. We have checked the breaker. What could be wrong
    Manuals+ clarified question
    Question

    Why has my Summerwind ceiling fan stopped working even though the remote shows a red light and the breaker is on?

    Answer

    If your Summerwind ceiling fan has stopped responding to the remote (even if the remote's red light is visible), the most common issue is a loss of pairing between the remote and the receiver, or a failure in the receiver unit itself.

    Based on the Summerwind SWT0002 RF Remote User Manual, you should first attempt to re-pair the remote to the fan:

    1. Ensure the power to the fan is turned on at the wall switch or breaker.
    2. Locate the LEARN button on your remote (indicated as button #8 in the manual, typically found inside the battery compartment or on the back).
    3. Keep pressing the LEARN button to pair it with the receiver. Usually, this must be done within 30-60 seconds of restoring power to the fan.

    If re-pairing does not work, consider the following:

    • Receiver Failure: Since you have no light and no fan movement, the internal receiver (located in the fan canopy) may have failed. This is a common point of failure for RF-controlled fans after 1-2 years.
    • Remote Battery: Even if the red light shows, the battery may be too weak to send a strong RF signal. Try replacing the battery with a fresh one before assuming the fan is broken.
    • Wiring Check: If you are comfortable doing so, ensure the wire nuts inside the fan canopy haven't come loose due to fan vibration over the last year and a half.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.