CURT ECHO Mobile Brake Control User Manual

CURT ECHO Mobile Brake Control

51180

ECHO™ MOBILE BRAKE CONTROL
INSTALLATION MANUAL

BEFORE YOU BEGIN

WARNING WARNING
Read and follow the installation manual carefully.
Failure to do so could result in damage to the brake control unit, loss of trailer brakes or poor brake performance.

  • The vehicle must have +12V, ground, and turn signals connected to the 7-way socket. Brake output to the 7-way socket is not required.
  • See below for ‘Vehicle-Specific Requirements’.
    Go to curtmfg.com/part/51180 for up-to-date vehicle compatibility.
  • An existing aftermarket or factory brake control will not function if Echo brake control is installed.
  • No special wiring or connectors are required for use.

WARNING WARNING
Avoid distracted driving. Only make adjustments when the vehicle is stationary.

WARNING WARNING
Do not mount the Echo™ near the exhaust pipe.
Failure to do so may result in heat damage, loss of functionality, and risk of fire.

NOTICE
Prior to driving, test all trailer lights while the trailer is plugged into the Echo™.

NOTICE
If your vehicle comes with a trailering app on the vehicle console, make sure its trailer function is enabled so the Echo™ will have power at the 7-way connector of the vehicle. See the vehicle owner’s manual to enable this feature.

  • The Echo brake control uses the 7-way connector’s +12V connection to power the brakes, and it shares this power with the trailer. Ensure the fuse for this connection is rated for 30 amps.
    See the vehicle owner’s manual to determine the fuse location.
  • If the phone application cannot connect to the Echo due to an incorrect or missing PIN, contact CURT Product Support. They will need the serial number located on the label of your Echo brake control.
  • Clean and store the Echo in a safe, dry place when not in use.
    We recommend applying dielectric grease to the terminals.

VEHICLE-SPECIFIC REQUIREMENTS

If the LED on the Echo™ does not light when plugged into the 7-way connector, the +12V power pin may not have power from the vehicle.
Visit a CURT authorized installer to install a power wire to the battery.

If your vehicle is equipped with a towing prep package, it may be necessary to activate a tow/haul mode using a push-button or dash screen.
Some vehicles may require a trailer to be connected to detect a load and activate the +12V power.
Consult the vehicle owner’s manual for vehicle-specific details or contact CURT Product Support if you are having trouble diagnosing the issue. Known vehicle-specific requirements are listed below:

Ford F-150 (2018)

  • Requires tow/haul mode activation and/or load detection on 7-way before the +12V output is activated on the 7-way connector.
    Activate tow mode and connect trailer before attempting Bluetooth connection to the Echo. The LED on the Echo must be on.

Ford F-150 (15 – 17)

  • These vehicles may turn off the +12V output to the 7-way connector when in the park or during gear shifting, making the existing vehicle wiring incompatible with the Echo. To use Echo with these vehicles, visit a CURT authorized installer to install a power wire to the battery.

DOWNLOAD THE MOBILE APPLICATION

Mobile applications are available for Apple and Android OS. They can be accessed in the App Store or Google Play by scanning the respective QR code below or searching for ‘Echo™ Smart Control’.

  • Bluetooth must be enabled on your device for pairing to occur.
  • After the app is installed, follow the prompts for setup.

QR

https://play.google.com/store/apps/details?id=com.curtgroup     https://itunes.apple.com/us/app/echo-smart-control/id1427659579?ls=1&mt=8

INITIAL SETUP FOR BLUETOOTH CONNECTION
NOTICE
The vehicle needs to be running or the ignition in the ‘ON’ position with the vehicle in park.

NOTICE
At any moment during setup, if the LED on the Echo™ is red, stop and refer to the ‘Troubleshooting Guide’.

  1. Insert the Echo™ brake control into the 7-way vehicle socket.
    The LED will flash blue. The Echo™ is now ready to pair with the mobile application.
    • For first-time use of the Echo, connection to the mobile application is required. Bluetooth connection is not required if previously paired, but recommended when possible.
    INITIAL SETUP FOR BLUETOOTH CONNECTION
    (CONTINUED FROM PAGE 1)
  2. Enable Bluetooth in your mobile device settings.
  3. Launch the app and scan for the Echo™. Once the ‘Echo™ Brake Control’ is visible, select it. You will then be prompted to enter the six-digit PIN, found under the cap of the brake control unit or on the provided quick reference card. Once the pairing is complete, the LED light will be solid blue.
    CURT ECHO Mobile Brake Control solid blue

  4. Plug the trailer’s 7-way connector into the Echo™ brake control while parked on a level surface. With the brake control inserted and the vehicle started, the LED light on the Echo™ will flash yellow for five to eight seconds while calibration occurs. Once the device is calibrated the LED will turn solid green.

  • If the calibration takes longer than eight seconds remove and reinsert Echo into the vehicle’s 7-way socket.
  • If the LED does not light up, the 7-way may not have +12V power.
    Refer to the ‘Vehicle-Specific Requirements’ on page one and the ‘Troubleshooting Guide’ on page four of this manual.

APPLICATION SETUP

After pairing with the Echo™, you will be directed to the ‘Towing Profiles’ screen to set up your trailer’s profile. You can create and save profiles for multiple vehicles, trailers, and load conditions.
Setting configuration is required when trailer conditions change or the brake control is being used for a different trailer or vehicle.

CURT ECHO Mobile Brake Control SETUP

WARNING WARNING
Avoid distracted driving.
Only make adjustments when the vehicle is stationary.

CURT ECHO Mobile Brake Control Avoid

CONFIGURING PROFILE SETTINGS
In your ‘Active Profile’ screen, you can adjust settings.

  1. Manual Brake Activation:
    Activate manual brake control by pressing and holding the orange button.
  2. Current Brake Level:
    The blue ring indicates the current brake output level.
  3. Max Output:
    The maximum level of the brake is set by the ‘Max Output’ setting.
  4. Sensitivity Level:
    The sensitivity of the braking power is set by the ‘Sensitivity’ setting.
  5. Screen Theme:
    Select the look of your screen for day or night. Note: ‘Max Output’ and  ‘Sensitivity Level’ are adjustable in increments of five.

CURT ECHO Mobile Brake Control Brake Level

WARNING WARNING
If a communication error occurs between the mobile application and the brake control, the ‘Manual Brake Activation’, ‘Max Output’ and ‘Sensitivity Level’ setting updates will not take effect, and condition notifications from the brake control will not be sent. The brake control will continue to function properly at the most recently programmed settings and braking operation will not be affected.

Manual Brake Activation
Manual brake control activation is used in situations where a slow reduction in speed is desirable. As the manual control is activated,the Echo™ begins to apply the trailer brakes. Manual output can be activated by pressing and holding the orange button in the app.
The manual control can be set up to apply 100% of the unit’s power to the trailer brakes or to limit power to the output control setting.
Echo™ is factory-set with the switch in the ‘limited to the output control’ position. This can be changed in the app settings menu.

Max Output
The output control establishes the max amount of power available to the trailer brakes when braking. The output should be adjusted during initial setup, when trailer load changes, when different trailers are used, or when adjustment is needed for changing road or driving conditions.

Sensitivity Level
The sensitivity level adjusts trailer aggressiveness when activated during braking, not manual override. Sensitivity adjustment has no effect on the manual brake control. The sensitivity can be adjusted for individual driver preference, trailer load changes, or changing road conditions.

TEST DRIVE & ADJUSTMENT

Both the output and sensitivity can be adjusted to achieve smooth, firm stops. Output and sensitivity adjustments should only be made while stopped, with the transmission in park or neutral, parking brake applied, foot off the brake pedal, and no manual control actuation. Note: Perform the adjustments in a safe environment with minimal vehicle traffic.
Starting with the output adjustment, drive forward on a dry and level paved or concrete surface. At approximately 25 mph, apply the vehicle’s brakes. If trailer braking is insufficient, increase the max output setting in the brake control application. If the trailer brakes lock up, decrease the max output. Repeat this process until stops are firm, just short of lock-up.
Once the output is set, adjust the sensitivity by driving forward at approximately 25 mph and press the brake pedal. The vehicle and trailer should make a smooth stop. If the stop seems slow and more aggressive braking is desired, increase the sensitivity level through the brake control application. If the stop seems too aggressive, decrease the sensitivity level in the application.
Make several stops at various speeds and adjust the sensitivity unit stops to be smooth and firm. Slight adjustment to the output control may also be desirable. Note: If any problems occur during the setup, refer to the ‘Troubleshooting Guide’ on the last page of this manual.

LED STATUS INDICATOR

A single LED on top of the Echo™ shows the status of the brake control unit. Refer to the icons and descriptions below.

Device Device not paired, no trailer connected (flashing blue)
paired The device paired, no trailer connected
(solid blue)
Calibrating Calibrating Echo™
flashing yellow)
Device not paired Device not paired, trailer connected
(flashing green)
Device paired, The device paired, trailer connected
(solid green)
Wiring error Wiring error
(flashing red)
Hardware Hardware fault
(solid red)
No power No power
(no light on)

 

Indicator Status
Flashing blue Device not paired, no trailer connected
Solid blue The device paired, no trailer connected
Flashing yellow Calibrating Echo
Flashing green Device not paired, trailer connected
Solid green The device paired, trailer connected
Flashing red Wiring error
Solid red Hardware fault

TROUBLESHOOTING GUIDE

Condition Problem Cause Possible Solution
LED does not light No power to brake control. no ground on vehicle 7-way Check vehicle power and ground wiring
Trailer mode not activated for vehicle
Vehicle requires trailer to activate 7-way power
Unable to connect to mobile devices No power to brake control, no ground on vehicle 7-way Invalid Bluetooth PIN Check Echo LED status for power
Input PIN from label or quick reference card
Enable Bluetooth or grant permissions
Check smartphone compatibility
Solid red LED for more than 10 seconds Hardware fault Contact CURT Product Support
Flashing red LED Contamination in trailer plug socket Check for clean and dry trailer plug
Short in trailer brake wiring Locate and correct short
Accelerometer error Unplug the brake control and plug it back in
Short or overload in trailer brakes Troubleshoot trailer brake circuit per brake manufacturer’s instructions
No trailer brakes, pedal or manual Mis-wired 7-way connector
Improper or corroded trailer wiring
Weak or missing ground
Confirm vehicle and trailer 7-way connections
No trailer brakes, pedal or manual (device notification of error) Loss of trailer connection, unplugged or bad wiring Confirm vehicle and trailer 7-way connections
No response on manual override or brake output Mis-wired 7-way connector
Improper or corroded trailer wiring
No or intermittent power to brake control Weak or missing ground
Wireless connectivity error
Confirm vehicle and trailer 7-way connections Check Bluetooth and application settings
Reduced braking power on manual override or brake output Weak or missing ground
Improper max power or sensitivity settings Improper or corroded trailer wiring
Confirm vehicle and trailer 7-way connections Check Bluetooth and application settings Increase max power or sensitivity settings
Trailer brakes on all the time (LED shows red) Mis-wired 7-way trailer connector Confirm vehicle and trailer 7-way connections
App signals ‘low voltage’ Low battery voltage Check vehicle battery and replace if needed Confirm vehicle 7-way connections and wiring
App signals a ‘disconnect’ Trailer connector is disconnected Reconnect the trailer connector
Confirm vehicle 7-way connections and wiring
App signals ‘overload’ Trailer brakes are overloaded Reconnect the trailer connector
Confirm vehicle 7-way connections and wiring Check trailer brake wiring for short circuits
Wireless disconnect Mobile device disconnected while driving
No or intermittent power to brake control
Stop the vehicle and reconnect to mobile device Confirm vehicle 7-way connections

5WARRANTY & PRODUCT REGISTRATION
CURT Group stands behind our products with industry-leading warranties. You can help us continue to improve our product line and help us understand your needs by registering your purchase at:
warranty.curtgroup.com/surveys
At CURT Group, the customer is king. We value your feedback and we use that information to make improvements to our products. Please take a minute to let us know how we are doing.

CONNECT WITH US
T WITH US

PAGE 4 • 51180-INS-RD • 877.287.8634 • NEED ASSISTANCE? • CURTMFG.COM

Documents / Resources

PDF thumbnailECHO Mobile Brake Control
User Manual · ECHO Mobile Brake Control, 51180

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. Can I store the break control unit in the truck for winter or should I keep it in the heated house

    Jeff weis asks Can I store the break control unit in the truck for winter or should I keep it in the heated house
    Manuals+ clarified question
    Question

    Can I store the CURT Echo brake control unit in my truck during winter, or should I keep it in a heated house?

    Answer

    According to the CURT ECHO Mobile Brake Control manual, you should clean and store the Echo in a safe, dry place when not in use. While the manual does not explicitly mandate a heated environment, it emphasizes protecting the unit from moisture and contamination.

    To ensure the longevity of the device during winter storage, follow these guidelines:

    • Keep it dry: Storing the unit inside a climate-controlled environment (like a heated house) is generally safer than leaving it in a vehicle where temperature fluctuations can cause condensation.
    • Protect the terminals: The manual recommends applying dielectric grease to the terminals before storage to prevent corrosion.
    • Clean the unit: Ensure the device is clean before putting it away for the season.

    Given that the device is a portable, plug-and-play Bluetooth unit, bringing it indoors is a best practice to avoid extreme cold and moisture exposure that could affect the internal electronics or the accelerometer.

  2. When my Tocoma is idling a sign goes on saying “vehicle battery”. Does anyoneknow what that means?

    Jerry Holt asks When my Tocoma is idling a sign goes on saying "vehicle battery". Does anyoneknow what that means?
    Manuals+ clarified question
    Question

    What does the 'vehicle battery' or 'low voltage' warning mean on the CURT Echo app?

    Answer

    According to the Troubleshooting Guide in the CURT Echo Mobile Brake Control manual, if the app signals 'low voltage' (which may appear as a 'vehicle battery' warning on your device), it indicates that the system has detected Low battery voltage.

    To resolve this, the manual recommends the following steps:

    • Check the vehicle battery: Ensure your battery is in good health and replace it if necessary.
    • Confirm connections: Verify the vehicle's 7-way connector wiring and connections are secure and free of corrosion.
    • Check idling conditions: Since the Echo uses the 7-way connector's +12V connection to power the brakes, a drop in voltage while idling may trigger this alert if the alternator output is low or the battery is weak.

    If the issue persists, you may need to consult your vehicle's owner's manual or visit a CURT authorized installer to verify the +12V power pin is receiving consistent power from the vehicle.

  3. I’ve already lost two of the rubber straps that hold the controller in place on my 2019 Toyota 4Runner. One was replaced by Curt, since I lost that one, too, I’ve been using zip ties. Last use, none of the running lights would illuminate. One of the campground guys tightened it down for me and we got it working, but I’m pretty sure it won’t stay put for future usage. I haven’t used it since that trip in early July. Any suggestions to make it consistently perform as designed? My previous devises have been hardwired and they do work better. But, I don’t want to take it back in invest in another kind of brake controller. I’d just like this one to work. I purchased my InTech Sol Horizon from Gerzensky’s in Lakeland Florida.

    Margaret Stocker asks I've already lost two of the rubber straps that hold the controller in place on my 2019 Toyota 4Runner. One was replaced by Curt, since I lost that one, too, I've been using zip ties. Last use, none of the running lights would illuminate. One of the campground guys tightened it down for me and we got it working, but I'm pretty sure it won't stay put for future usage. I haven't used it since that trip in early July. Any suggestions to make it consistently perform as designed? My previous devises have been hardwired and they do work better. But, I don't want to take it back in invest in another kind of brake controller. I'd just like this one to work. I purchased my InTech Sol Horizon from Gerzensky's in Lakeland Florida.
    Manuals+ clarified question
    Question

    How can I ensure the CURT Echo remains securely attached and maintains a consistent electrical connection for running lights?

    Answer

    To ensure your CURT Echo performs consistently and maintains a reliable connection for your running lights, please consider the following steps based on the product manual and troubleshooting guidelines:

    • Terminal Maintenance: The manual recommends cleaning the terminals and applying dielectric grease. This is crucial for preventing corrosion and ensuring a solid electrical path for functions like running lights, especially if the unit has been exposed to the elements.
    • Secure Mounting: While the rubber strap is the primary mounting method, the manual emphasizes that the unit must be firmly seated in the 7-way socket. If the socket on your 4Runner is loose or the Echo is vibrating, it can cause intermittent power loss. Ensure the vehicle's 7-way socket spring-loaded lid is engaging with the Echo to help hold it in place.
    • Check for Contamination: A "Flashing Red LED" or intermittent light failure can be caused by contamination in the trailer plug socket. Ensure both the vehicle-side and trailer-side connectors are clean and dry.
    • Grounding and Wiring: Intermittent light issues are often caused by a weak or missing ground. Verify that the 7-way connector on your Toyota 4Runner has a clean, solid ground connection. The manual suggests confirming both vehicle and trailer 7-way connections if you experience no response or reduced power.
    • Vehicle-Specific Settings: For some vehicles, you may need to ensure that the "Tow/Haul" mode is active or that the vehicle's trailering app (if equipped on your dashboard) is enabled to provide consistent +12V power to the 7-way connector.

    If the physical connection remains unstable despite these steps, you may want to have a technician inspect the 7-way socket on your vehicle for wear or internal corrosion that could be preventing the Echo from seating deeply enough to maintain contact.

  4. my controller seems to apply brakes when parking lights are on, or automatic lights. also seems to apply on initial take off from stop, especially if heading uphill. has worked fine with lights on for 2 years, but now is constantly applying about 60 percent brake while driving. had to disconnect and tow without trailer brake.

    Jeff ladebush asks my controller seems to apply brakes when parking lights are on, or automatic lights. also seems to apply on initial take off from stop, especially if heading uphill. has worked fine with lights on for 2 years, but now is constantly applying about 60 percent brake while driving. had to disconnect and tow without trailer brake.
    Manuals+ clarified question
    Question

    Why are my trailer brakes applying automatically when the parking lights are on or when accelerating from a stop?

    Answer

    Based on the CURT Echo Mobile Brake Control manual and troubleshooting data, your issue likely stems from a wiring conflict or a hardware fault that has developed over time. Here are the recommended troubleshooting steps:

    • Check for a 'Flashing Red' LED: If the LED on the unit is flashing red, the manual indicates a possible Accelerometer Error. The solution is to unplug the brake control and plug it back in to recalibrate.
    • Verify 7-Way Wiring: The manual specifically lists 'Trailer brakes on all the time' as a symptom of a mis-wired 7-way trailer connector. Since your issue is triggered by the parking lights, there may be a short or 'backfeed' between the 12V lighting circuit and the brake output circuit within the vehicle's socket or the trailer's plug.
    • Clean Terminals: The manufacturer recommends cleaning the terminals and applying dielectric grease. Contamination in the trailer plug socket can cause a flashing red LED and erratic braking behavior.
    • Hardware Fault: If the LED shows a Solid Red light for more than 10 seconds, this indicates a permanent hardware fault. In this case, the manual advises contacting CURT Product Support at 877.287.8634.

    Note: External user reports suggest that if the internal accelerometer fails, the unit may incorrectly interpret vehicle movement (like accelerating uphill) as a braking event, leading to the constant application of trailer brakes. If recalibration and cleaning the 7-way connector do not resolve the issue, the unit may need replacement under warranty.

  5. We are finding it hard to get proper settings for firm and smooth braking. It feels like a ‘clunk’ when car brake is applied.

    When car brake is applied, the app inconsistently reads “brake is applied”. Why is it not consistent?

    We have to get out of vehicle, stand closer to control to re-pair devices. Is this usual?

    We have to re-pair often. Is this usual?

    Where can I find reviews and advice on how to use this?

    The Hansens asks We are finding it hard to get proper settings for firm and smooth braking. It feels like a ‘clunk’ when car brake is applied.

    When car brake is applied, the app inconsistently reads “brake is applied”. Why is it not consistent?

    We have to get out of vehicle, stand closer to control to re-pair devices. Is this usual?

    We have to re-pair often. Is this usual?

    Where can I find reviews and advice on how to use this?

    Manuals+ clarified question
    Question

    How do I adjust the CURT ECHO for smooth braking, and why is the app connection inconsistent?

    Answer

    To achieve smooth and firm braking without a 'clunking' sensation, you must calibrate both the Max Output and Sensitivity Level in the ECHO Smart Control app:

    • Max Output: Drive at approximately 25 mph and apply the brakes. Increase the output if braking is insufficient, or decrease it if the trailer brakes lock up. Repeat until stops are firm but just short of locking.
    • Sensitivity Level: Once output is set, drive at 25 mph again. If the stop feels slow, increase sensitivity. If it feels too aggressive (causing a clunk or jerk), decrease the sensitivity level.

    Regarding the inconsistent "brake is applied" reading and frequent re-pairing, the manual and troubleshooting guide suggest several possibilities:

    • Wireless Connectivity: The app does not need to be open for the Echo to function; it will use the last saved profile. However, if you are losing connection, ensure your phone's Bluetooth permissions are fully granted and that there is no interference.
    • Power Issues: Inconsistent readings can be caused by a weak or missing ground, or intermittent power from the vehicle's 7-way connector. Check that your vehicle's +12V connection is stable and the fuse is rated for 30 amps.
    • Accelerometer Error: If the unit behaves erratically, try unplugging the brake control and plugging it back in to reset the internal accelerometer.
    • Vehicle Specifics: Some vehicles (like 2015-2018 Ford F-150s) may turn off power to the 7-way connector in certain gears or require 'Tow/Haul' mode to be active for consistent power.

    If you continue to experience pairing issues that require standing next to the unit, this is not typical behavior. You may have a hardware fault (indicated by a solid red LED) or a wireless connectivity error. For further technical advice and reviews, you can visit the CURT website or the Apple/Google Play app store pages for the 'Echo Smart Control' app.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.