auraLED Led Lights User Manual
INTRODUCTION & FEATURES
Give your home living room a unique atmospheric twist with the ColorStrip LED lights by tzumi. Designed with a safe adhesive backing, this colorful backlight can be fixed directly onto the back of your TV or computer screen, enhancing your home theater and easing light-induced fatigue. It fits screens up to 65″ and includes a wireless remote controller, which provides you with the freedom to customize your selection of 16 colors and find the perfect brightness, rhythm, and color scheme.
PACKAGE CONTENTS
- 1 6.5 Ft LED Mood Light
- 1 Wireless Remote Control
Product Overview & Functions
Wireless Remote Control
CR2025 cell battery (included)
When Remote Control operation becomes slow, it is time to change the battery. Compatible with CR2025 and CR2032 battery types.
INSTALLATION
NOTE: Please make sure that the back surface of your TV is clean from dust, oils, or fingerprints before attempting to apply your LED Mood Light. Use an alcohol based cleaning cloth to wipe the back of your TV.
- Locate the USB port on the back of your TV. If your TV does not have a USB port, you may use any other USB power source.
- Make sure that you are satisfied with the coverage area of the LED strip prior to peeling off the adhesive tape. Make sure that the USB cable is placed near the USB port and has enough slack to reach safely. The Remote Receiver must also be visible in order to work properly. See below.
- Peel off the backing of the strip to expose the adhesive.
- Apply to the cleaned surface of the back of TV. Press down for a couple of seconds to secure.
- Connect the LED Strip with the USB Cable and insert the cable into the USB port.
- Once connected, remove the protective plastic strip from remote control to activate the battery.
- Press the ON button to turn on the LED strip.
- Refer to the color combinations settings on the remote to customize your LED strip.
Assembly
Connect the LED strip with the USB cable.
See below for suggested placement depending on your TV size:
These illustrations are for visual reference only. LED Strip placement will vary depending on each individual unit.
WIRELESS REMOTE CONTROLS
Button 1 and 2 can be used to control the brightness for button 5, change the speed for button 6,7,8,9.
- Brightness (Up)
- Brightness (Down)
- Power OFF
- Power ON
- LED Color Buttons -16 colors
- Flash Transition Effect
- Strobe Transition Effect
- Fade Transition Effect
- Smooth Transition Effect
When remote control operation becomes slow, it is time to change the battery. Replace with a new cell battery.
- Compatible with CR2025-CR2032 battery types
LED LIGHT STRIP SPECS
LED Strip
| Input: |
DC 5V/0.5A – 2A |
| Power Consumption: |
2.5w -10W |
| LED Chip: |
5050, RGB |
| Color |
16 colors with 4 Mood light settings |
| Beam Angle: |
120 degrees |
| LED Strip: |
60 LED lights 16.5 foot (78″) |
| Back Adhesive: |
3M self-adhesive |
| Working Temperature: |
-20°C – 45°C |
| Working Humidity: |
0% – 80% RH |
CARE & IMPORTANT SAFEGUARDS
- Keep LED strip away from flammable objects.
- Always make sure that all parts have been connected properly.
- Check to make sure the voltage of the power source (USB) is 5V.
- Do not connect the LED strip to the power source until all of the installation have been completed.
- Do not cut any part of the LED strip or its connectors.
- Always make sure that the Remote Receiver is not covered or blocked. This will ensure proper operation using the remote control.
- If this product malfunctions, please do not try to repair it yourself, take it to a qualified electrician.
Documents / Resources
 | Led Lights |
References
- User Manualmanual.tools
The Color Strip LED light always reverts back to “FLASH” once turned off rather than the last setting (such as “WHITE”). Is there a way to always turn back on to the last setting since the lights are turned on/off daily?
How can I make the auraLED Color Strip remember its last color setting instead of reverting to 'FLASH' mode when turned off?
Based on the provided manual for the auraLED Color Strip, there is no mention of a built-in memory function that saves the last used setting when the power is completely cut (such as turning off a TV or unplugging the USB source). The device typically defaults to its factory start-up mode, which is often a cycle or 'FLASH' mode, when it receives new power.
To potentially maintain your settings, try the following:
If the unit continues to reset even when using the remote's power button while connected to a constant power source, it is likely a limitation of the internal controller's hardware.
Read the full Q&A page
i have the same question
How do I set up and use the auraLED ColorStrip LED lights?
To set up and use your auraLED ColorStrip LED lights, please follow these steps based on the user manual:
Installation:
Using the Remote:
Important Note: Ensure the Remote Receiver on the LED strip is not covered or blocked to ensure the remote control functions properly.
Read the full Q&A page
Is there a way to customize the light options? For example: Fade between Red, white, and blue only.
How can I customize the light options to fade between specific colors like red, white, and blue?
Based on the auraLED ColorStrip manual, the device features 4 pre-set mood light settings (Flash, Strobe, Fade, and Smooth) and 16 selectable colors. However, the manual does not indicate that the remote supports custom programming for specific color sequences, such as fading only between red, white, and blue.
To use the built-in transition effects, you can use the following buttons on your wireless remote control:
You can use Buttons 1 and 2 to change the speed of these transitions. While you can manually select Red, White, or Blue using the individual color buttons, the automated fade cycles typically cycle through all available colors in the pre-programmed sequence.
Read the full Q&A page
Can a usb adater that plugs into a 110 outlet be used?
Can I use a USB wall adapter to power the auraLED lights?
Yes, you can use a USB wall adapter that plugs into a 110V outlet. According to the manual, if your TV does not have a USB port, you may use any other USB power source. However, you must ensure the adapter meets the product's specifications: it should provide a DC 5V output with a current between 0.5A and 2A. Always check to make sure the voltage of the power source is exactly 5V before connecting the LED strip.
Read the full Q&A page
Anyone having experience of the LED lighting strip coming on when the TV is not on? Is this normal or can this happen?
Why do my auraLED lights turn on when the TV is off?
Yes, this can happen and is usually related to how your TV manages power to its USB ports. Many modern TVs continue to provide power to the USB ports for a short time after the screen is turned off, or they may 'pulse' power to the ports periodically to check for software updates or maintain network connections.
Because the auraLED ColorStrip is powered directly via the USB cable, any power coming from the TV will cause the lights to activate. To resolve this, you can:
Read the full Q&A page
The remote control isn’t controlling the lights. I have removed the battery plastic and have tried replacing the battery. The remote receptor is visible and not blocked by anything.
Why is my auraLED remote control not working even after removing the plastic tab and replacing the battery?
If your auraLED remote is still not controlling the lights after removing the plastic tab and replacing the battery, please check the following steps based on the manual:
If the lights still do not respond, there may be a hardware malfunction with either the receiver on the strip or the remote itself.
Read the full Q&A page
The lights stay green even after I turn them off.
Why do my auraLED lights stay green after I turn them off?
If your auraLED ColorStrip remains green after turning it off with the remote, it usually indicates that the strip is still receiving a small amount of residual power from the USB source or that the remote signal was not fully processed. You can try the following steps to resolve this:
If the lights continue to glow while the unit is supposedly off, there may be an internal malfunction. Per the manual's safeguards, do not attempt to repair the product yourself; if it malfunctions, it should be taken to a qualified electrician or replaced.
Read the full Q&A page