GE Electronic-controlled Refrigerator Error Codes
GE Electronic-controlled Refrigerator Error Codes
Error Codes
These error code explanations can help you diagnose a problem with your GE refrigerator with a digital display on the dispenser control panel.
Error codes appear on the dispenser control panel display when the electronic control board detects component failures. When an error code appears:
- Match the error code on your refrigerator with the error code in the chart below.
- Make sure that the condition listed with the error code is the same as the symptom(s) shown by your refrigerator.
- Read the DIY advice to learn how to troubleshoot the issue and determine the problem part.
- Follow repair guide instructions (if listed) to fix the broken part
| Error Code | Condition | DIY Advice |
| FF | Check frozen foods for thawing |
Check/Repair
Freezer temperature has been above normal for more than 2 hours. Make sure that the refrigerator and freezer doors are closed properly. Replace the door gaskets if damaged. Press the System Check button to clear the error code and check for other system failures. If the PF code appears, then the FF code was likely caused by a power failure. Keep the refrigerator and freezer doors closed as much as possible to allow the interior temperatures to recover. |
| PF | Power has been interrupted |
Check/Repair
Make sure that the power cord is properly plugged into the electrical outlet. Replace the power cord if damaged. Check the condition of food in the refrigerator and freezer compartments. Discard any spoiled food. Press the System Check button to clear the error code and check for other failures. |
| CI | Ice maker not operating properly |
Check/Repair
Clear jammed ice cubes from the ice mold. If the ice mold isn’t filling with water, restore the water supply to the ice maker. If you turned off the water intentionally, also turn off the ice. Press the System Check button to clear the error code and check for other system failures. If the CI code reappears, replace the ice maker assembly. |
| dE | Defrost system error |
Check/Repair
The defrost cycle has not run for more than 48 hours. Unplug the refrigerator and reconnect any loose wires in the defrost system. Replace the wire harness if damaged. Replace the defrost heater if damaged. It may be normal for the refrigerator to operate without defrosting for more than 48 hours when operating in a space that’s below 55 degrees F. Reset the code by pressing the System Check button |
| CC | Freezer temperature is too warm |
Check/Repair
Freezer temperature has been above normal for more than 2 hours. Adjust the controls according to the instructions in your owner’s manual. Close the refrigerator and freezer doors completely. Replace the door gaskets if damaged. Press the System Check button to clear the error code and check for other system failures. |
FAQ’S
Normal Operation Codes for Refrigerators
tF: If the temperature display shows a tF (could look like an EF, an upside down F with an F or something similar), this is not an error code, it is the Turbo Freeze (tF) setting indicator. For more information about this feature, visit: Refrigerator – TurboFreeze Setting.
Try resetting the control panel by turning off power to the refrigerator briefly. Unplug the refrigerator or turn it off at the circuit breaker for 30 seconds to reset the control. Replace the filter. Purchase a GE Appliance Part online.
Fix: Like the PF error code, try to clear the error code by pressing “System Check” or “Cancel,” and if that doesn’t work, unplug the refrigerator for a few minutes. If the error code remains, the control board should be inspected for signs of burning or other damage. A damaged control board will need to be replaced.
If the GE refrigerator water dispenser light is blinking, then it could be a problem with the ice maker. GE Appliances recommends turning the ice maker to the off position for 15 seconds. Push the water dispenser paddle exactly three times during those 15 seconds before turning the ice maker back on.
Code problem the defrost. System has not operated properly in the last 24. Hours code cc problem check the temperature controls because the temperature for the refrigerator. Is incorrect.
You will typically see ‘tF’ in the temperature display when the freezer is set to TurboFreeze.
The symbol may look like an ‘EF’, an upside down f with an F or something similar. This is not an error code, it is the TurboFreeze (tF) setting indicator.
The 5Y EF error code indicates an issue with or between the fan motor and the control board. I suggest check the wiring between evaporator fan and control board. Make sure everything is plugged in securely. You can also resent the appliance but cutting power off to the appliance for 5 mins to see if the code clears.
To clear the SY EF error code, you must ensure that the freezer evaporator fan motor can work without issues. Once you do that, you can remove the code by resetting the appliance.
In many cases the problem is do to the fact that the evaporator fan cannot operate freely due to an ice buildup on the fan blades. Sometimes one or more of the fan blades, in the case of fans equipped with metal blades, have become bent causing it to jam against the metal fan shroud.
Locate the lock button and hold it in for three seconds. This should remove the control lock feature.
Error codes appear on the dispenser control panel display when the electronic control board detects component failures. When an error code appears:
Match the error code on your refrigerator with the error code in the chart below.
Make sure that the condition listed with the error code is the same as the symptom(s) shown by your refrigerator.
Read the DIY advice to learn how to troubleshoot the issue and determine the problem part.
Follow repair guide instructions (if listed) to fix the broken part
What would cause a GE refrigerator to not be cold?
If the refrigerator is not cold enough the condenser coils may be dirty. The condenser is like a radiator and must stay clean in order to dissipate the heat which was removed from the inside of the refrigerator. As the coils get dirtier the refrigerator becomes less efficient, which makes it work harder to cool down.
VIDEO
www://geappliances.com/
References
- User Manualmanual.tools
It’s a shame I have to Google to find this. This should be a page in the Users Manual.
Where can I find the error code list for GE electronic-controlled refrigerators?
It is common for manufacturers to omit technical error codes from the basic user manual, often reserving them for service manuals. For GE electronic-controlled refrigerators with digital displays, here are the most common error codes and their meanings:
To clear most codes, you can press the System Check or Cancel button. If the code persists, try resetting the refrigerator by unplugging it or turning off the circuit breaker for 30 seconds.
If you need a specific manual for your model, you can use the Manuals+ Deep Search tool to find the full PDF documentation.
Note: If an error code remains after a reset, it may indicate a component failure on the electronic control board that requires professional service.
Read the full Q&A page
I installed a filter bypass from GE and the display show 6P and the error light blinks a few seconds when you dispense water. I know it is from the filter bypass but how do you reset it? I am on a reverse osmosis system and don’t need a filter.
Thank you
Thank you
How do I reset the 6P error code on my GE refrigerator after installing a filter bypass?
The 6P code (which often looks like 'GP' or '6P' on the digital display) is not a standard mechanical failure error code, but typically indicates a Leak Detected or a Pressure issue related to the water filtration system. Because you are using a reverse osmosis (RO) system with a bypass, the refrigerator may be detecting a drop in water pressure or a communication error with the filter sensor.
To reset the display and clear the blinking light, try the following steps:
If the code remains after a hard power reset, it may indicate that the refrigerator's internal leak detection sensor (if equipped) has been triggered or the bypass plug is not being recognized by the electronic control board.
Note: Uncertainty exists regarding the specific model, as 6P is often associated with newer GE Profile or Cafe series leak-sensing manifolds.
For more general GE error codes, you can refer to the GE Electronic-controlled Refrigerator Error Codes guide.
Read the full Q&A page
mhn maaf utk penjelasan kode error klihatan kurang komplit.
klo kode sc berketip apa yg harus saya lakukan. mohon bimbingan trmksh.
klo kode sc berketip apa yg harus saya lakukan. mohon bimbingan trmksh.
What should I do if my GE refrigerator displays a blinking 'sc' error code?
On many GE electronic-controlled refrigerators, the 'sc' code is not actually an error code, but a status indicator for Sabbath Mode (sometimes appearing as 'Sb' or 'SA').
If your display is specifically blinking and the refrigerator is not cooling, it may indicate a communication error between the control boards. In this case, try a hard reset: unplug the refrigerator or turn off the circuit breaker for 30 seconds. If the code persists after a reset, the main electronic control board may need to be inspected for damage or replaced.
Read the full Q&A page
mohon bibingan klo sc berketip apa yg harus sy lakukan.
What should I do if the 'sc' code is blinking on my GE refrigerator?
On GE electronic-controlled refrigerators, the System Check (SC) indicator is often associated with the diagnostic process. If you see a code that looks like 'sc' or is related to the system check, follow these steps:
If the blinking continues and the refrigerator is not cooling, the control board may need to be inspected for damage or burning.
Note: The provided manual does not list a specific 'sc' error code as a failure, but refers to 'System Check' as the method to clear other errors.
Read the full Q&A page