IGNITE REMOTERGB RF Remote Controller Instructions

ignite-logo

IGNITE REMOTERGB RF Remote Controller

IGNITE REMOTERGB RF Remote Controller-

SPECIFICATIONS

IGNITE-REMOTERGB RF-Remote-Controller- fig 4

BUTTONS DESCRIPTION

IGNITE-REMOTERGB RF-Remote-Controller- fig 1

PARTS DESCRIPTION

IGNITE-REMOTERGB RF-Remote-Controller- fig 2 IGNITE-REMOTERGB RF-Remote-Controller- fig 3

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  •  Increase the separation between the equipment and receiver.
  •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  •  Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

1000 Liberty Industrial Dr.
O’Fallon, Mo 63366
www.anjonmfg.com

sales@anjonponds.com

Documents / Resources

PDF thumbnailREMOTERGB RF Remote Controller
Instructions · REMOTERGB, 2A4WX-REMOTERGB, 2A4WXREMOTERGB, REMOTERGB RF Remote Controller, RF Remote Controller

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. pairing instructions

    🇺🇸 James Jeffries asks pairing instructions
    Manuals+ clarified question
    Question

    How do I pair the IGNITE REMOTERGB RF Remote Controller?

    Answer

    The provided manual for the IGNITE REMOTERGB RF Remote Controller does not explicitly list a multi-step pairing sequence (such as a button-hold pattern). However, to ensure the remote functions correctly with the receiver, please follow these setup requirements:

    • Antenna Setup: Ensure the spring antenna on the controller is lengthened vertically to a height of 60–80mm for proper signal reception.
    • Power Connection: The controller must be connected to an AC 12V Low Voltage transformer.
    • Compatibility: This remote is specifically designed to be used only with the product REMOTERGB and 4-core cable DC 12V RGB lighting (Max 60W).

    If the remote is not responding after these steps, try cycling the power to the transformer and then pressing the ON/OFF button. If you continue to experience issues, you may contact Anjon Manufacturing at 1-800-553-5605 for technical support.

  2. Can you program a red, white and blue sequence with the remotergb?

    🇺🇸 Bruce asks Can you program a red, white and blue sequence with the remotergb?
    Manuals+ clarified question
    Question

    Can I program a custom red, white, and blue color sequence on the Ignite REMOTERGB RF Remote Controller?

    Answer

    Based on the Ignite REMOTERGB RF Remote Controller manual, it is not possible to program a custom color sequence like red, white, and blue. The remote features pre-set modes and a color ring for selection, but it does not include a programmable memory function for custom sequences.

    You can interact with the colors using the following buttons:

    • M+ and M- (Color Selection): These buttons cycle through the pre-programmed color modes and dynamic patterns.
    • RGB Color Ring: Allows you to manually select a static color by touching the wheel.
    • S+ and S- (Speed): Adjusts the speed of the existing dynamic patterns.

    While you can manually switch between red, white, and blue using the color ring or by cycling through modes, the device does not support creating a user-defined sequence of those specific three colors.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.