![]()
Touch Two Stereo headset C5 User Manual

Touch Two Stereo headset C5 User Manual
brief introduction
Thank you for purchasing the C5 wireless earbuds ! The C5 useof the newest technology supports all functions by touch control and has exceptional audio quality. The C5 focuses on improving and enhancing user experience by providing a comfortable fit and ergonomic in-ear design. It is designed to fit the auricle perfectly so that the user is free from pressure and distending pain during prolonged use. With the Portable and Wireless Magsafe charging, you can enjoy charging anytime and anywhere. For the best user experience, please read this manual carefully before initial use of the C5 earbuds
Safety Rules
- For safety, please comply with the rules mentioned in this manual
- Keep device away from sharp edges, uneven surfaces, metal objects, and knockout.
- Do not open, dismantle or attempt to repair the earbuds. Doing so may cause accidental fire, electronic board failure, or damage to the earbuds. All warranty will be canceled.
- Do not wipe or clean the earbuds with oils or any volatile liquids.
- Do not use the earbuds in places where potential personal safety is atrisk or in danger.
Packing details
| — C5 Bluetooth headset | 1 pair |
| — Charging Cable | 1 |
| — Medium silicone ear cap | 1 pair |
| — Small silicone ear cap | 1 pair |
| — Instruction manual | 1 serving |
| — Charging storage box | 1 |
| — Hanging rope | 1 |
| — Packing box | 1 set |
Product Information

① Charging storage box
② Cavity
③ battery indicator
④ microphone
⑤ Silicone ear cap
⑥ Silicone plug
Quick Start Guide
1. Headphone wearing method
R/L is printed on the earphone case, please wear it in the correct direction, the sound quality will be better!

LED position down
A. Take the earbuds out of charging case and remove the PET insulator.
Put the earbuds back in the charging case to activate. The earbuds will now power on automatically once you take them out of case B.Put the L and R earbuds into your ears. The L and R earbud will find each other and pair. Next, the tone” connected will be heard
C. When the two earbuds successfully pair, the tone”Left channel, Right channel” will be heard Activate Bluetooth on your phone. On the device list, connect to the”Touch Two C5and then the tone second device connected will be heard
D.How to use the single ear: Take out the single earbuds from the charging box to enter the red and blue lights alternately which is connection succeeded. If the Bluetooth device name is not found, touch the surface twice to search and connect.
ATTENTION:
PARING TO THE PHONE IS ONLY REQUIRED FOR THE FIRST TIME YOU CONNECT. AFTER THE FIRST TIME, THE EARBUDS WILL
AUTOMATICALLY CONECT TO YOUR PHONE WHEN YOU REMOVE THEM FROM THE CASE
3.Touch Functions:
Next: Double click on the right ear touch surface.
Volume reduction: Long press 2S of right ear surface.

Shut down:Long press left ear touch area for 4S

Previous: Click twice on the left ear touch area
Volume increase: Long press left ear touch area for 2S
(Note:Left and right device can be operated)
Activate voice assistant: Continuously click the touch panel three times
(Note:in standby mode)
Call function:Click once on the touch surface to answer or hang up the phone.
Reject the call: Double click on the touch surface
Play or pause music:Click once on the touch area
ATTENTION:
PLEASE REMOVE THE PROTECTIVE COVER ON THE EARBUDS BEFORE OPERATION. PLEASE KEEP AWAY FROM RADIO INTERFERENCE AND AVOID NOISY ENVIRONMENTS WHEN USING EABUDS PLEASE REPLAY THE HIGHT QUALITY FORMAT OF MUSIC OR LOCAL MUSIC OF THE DEVICE
4. Charging Case
A. Put the earbuds into the case exactly, the battery box will automatically charge the earphones until they are full.
B. Earbuds will automatically turn off once they are placed into the charging case
C. USB outlet supports 5V/1.5A output, which can provide emergency charging for mobile phones and other electronic products
ATTENTION:
REMOVE THE INSULATION COVER BEFORE INITIAL USE. RECHARGE THE CHARGING CASE IF NOT USED FOR OVER 90 DAYS. ONLY USE A GOOD QUALITY WIRELESS CHARGING TRANSMITTER AND CHARGING CABLE. THE EARBUD LED LIGHT WILL TURN BLUE WHEN IT IS FULLY CHARGED
5. Single Earbud Mode:
The L/R Earbud can used alone to connect to your Phone. On your phone, enter the Bluetooth device connection list and remove the”Touch Two C5 ” from the list. Redo the steps for Connect to Phone”but with only the L/R earbud.
Product Parameter
1. Earbud parameters:
Bluetooth Version: 5.0
Operation Voltage: 3.2V-4 2V
Impedance: 32Ω
Speaker sensitivity: 105db
Speaker Bandwidth: 20-20 KHZ
Microphone Sensitivity: -42+-2db
Earbud frequency: 2. 4-2.48GHZ
Compatible: A2DP/HFP/HSP/AVRCPEarbud
Working range: 10M
Single eartalk time: 6hrs
Music play: 4-5hrs
Single earbud standby time: 80 hrs
2. Charging case Parameters:
Large capacity battery
DC Charging Voltage: DC/5V
DC charge Current: 1A
DC output Current: Maximum 1. 5A
Troubleshooting Guide
| malfunction | the reason | Solution |
| Unable to start | Low battery | Charge the headset |
| Silent after matching | Match operation is incorrect | Rematch |
| Can talk, but red indicator illuminates | The battery is a low, Bright red indicator | Clear the headset immediately |
| Charging without prompt | The headphones are not put well | Check if the headphones are in place |
| Headset Automatic shut-down | Low battery | Charge the headset |
| Headphones have echo | The volume is too high or the environment is too noisy | volume adjustment Or change places |
| The call has a noise | Caused by environmental interference or Sound source equipment is far away | Change place or will The distance of the source device is close |
| The other party’s voice is small | The headset is not worn correctly | Adjust the position of the headset And adjust the volume |
| Bad signal, Intermittent | Too far or outside interference | Put the phone closer to the main earbud or keep from the outer interference signal |
FAQS
When you first use this earphone and you want to use the L/R earphone alone. You must double-click the L/R ear touch surface. Then you can find the “Touch Two C5S” in the Bluetooth device connection list. If you have connected your phone with the two earphones.
Please press and hold the power button for 3 seconds to turn on the earbuds. Then, please press and hold the power button for 3 seconds again to enter pairing mode. When you hear a beep, please search for “C5” in the Bluetooth settings of your phone and pair them. If you have any other questions, please contact our customer service hotline at 1626-869-0808.
Please connect C5 earbuds with a charging cable (included) into a USB port of a computer, then connect another end of charging cable into a charger adapter (not included). The LED indicator light will be red when charging, then it will be blue when fully charged (about 3 hours). When charging is completed, disconnecting from computer will cause it enter sleep mode automatically; if you want to wake it up, please press any button on C5 earbuds .
If your headphones’ battery is low, it may have trouble pairing—and I’ve even found some Bluetooth headphones stay turned on when in the case, meaning they’ll drain down to 0 percent faster than you expect. Try plugging them in and charging them fully before pairing, even if they say they have some battery left.
Scroll down the menu and tap on [Accessibility]. Then tap [Hearing enhancements]. You will see a toggle switch for [Mono audio]. Ensure the toggle switch is set to [Off].
From off status, press and hold the power button for about 15 seconds on both earbuds until the LED flashes BLUE. Step 2: Once connected, the LED on the left earbud will flash BLUE twice every 5s and the LED on the right earbud will alternate between flashing BLUE & RED indicating that it is in pairing mode.
Turn ON the Bluetooth function on your mobile phone. 3. Pair: Search for “A1” and select it to pair, there will be a short beep means Bluetooth headphone is connected with mobile phone. The Bluetooth headphone will be reconnecting automatically if your mobile phone has been paired.
If your Bluetooth devices won’t connect, it’s likely because the devices are out of range, or aren’t in pairing mode. If you’re having persistent Bluetooth connection problems, try resetting your devices, or having your phone or tablet “forget” the connection.
Delete the left and right earbuds pairing information (Reset the i12 TWS). In pairing mode, 5 click the power button until LED lit RED. Step 2: Long press the function key for 5 seconds to turn on the i12 TWS. Step 3: Enter pairing mode, pairing time is about 5 seconds, prompt tone “pairing mode”.
It’s called True Wireless Stereo (TWS), and it’s a unique Bluetooth feature that will let you enjoy true stereo sound quality without the use of cables or wires. TWS works as follows: You pair a primary Bluetooth speaker to your preferred Bluetooth-enabled audio source.
Open Settings, then tap Connected devices > Connection preferences > Bluetooth. Turn the Bluetooth switch to Off, or unpair Bluetooth audio devices that are already connected to your phone. Plug your headphones into the audio jack and play something to see if they work.
Turn off Bluetooth on all devices within 30 ft of the earbuds. Place earbuds in the charging case for 5 seconds. Remove earbuds from the case. The earbuds and charging case should now communicate as normal.
Many audio and electronics shops will do headphone repairs. If you can’t find a local place to do the work, you can look into shipping your headphones to the manufacturer or an independent repair center for a fix. And depending on the problem, your headphones may be covered by a warranty as well.
Some quality earphones can last for up to two to three years. But if your new pair stops working after just a few months, this could be due to one or a combination of these factors: You purchased a low-quality device.
If the power on the headphones is not turning on, the battery may not be inserted correctly or the battery may need to be replaced. Check the following items to troubleshoot this issue.
IMPORTANT: If model-specific information is needed to complete any of the steps, refer to the instructions supplied with the product.

Documents / Resources
![]() | Stereo headset C5 |
References
- User Manualmanual.tools

I have used these only a few times and they do not work at all. I have tried and tried to get them to work and they dont even charg. I am so dissappointed and really cannot afford to be wasting money. Please let me know where I can send this item for repair? Elaine E McMeekin
1605 Dyer Drive #510 London Ontario Canada
1605 Dyer Drive #510 London Ontario Canada
Why are my Touch Two C5 earbuds not charging or working, and where can I get them repaired?
I am sorry to hear your earbuds are not functioning. Before seeking a repair, please check a common setup issue that prevents charging: ensure you have removed the PET insulation covers from the earbuds. These are small protective films on the charging contacts that must be removed before the earbuds can charge in the case.
If you have already removed the insulators, please try the following troubleshooting steps from the manual:
Regarding repairs, the manual explicitly states in the Safety Rules (page 2) that you should not attempt to open, dismantle, or repair the earbuds yourself, as this will cancel the warranty. Unfortunately, the manual does not provide a specific service center address for Canada. Since Manuals+ is an archive of user manuals and not the manufacturer, we recommend contacting the original retailer or the brand's official support channel for warranty claims and repair locations.
Note: Please avoid posting your full home address in public comments for your own privacy and safety.
Read the full Q&A page
good but missing the problems I may have:
it happens to me that they do not pair together and in the bluetooth the name touch two c5s appears twice which are paired with one of the earphones, how can I pair them together thanks.
P.S. I can no longer find the package instructions
bravi ma manca i problemi che posso avere :
mi succede che non si abbinano assieme e nel bluetooth appaiono 2 volte il nome touch two c5s le quali sono abbinate a uno dei auricolari, como posso abbinarli assieme grazie .
P.S. nontrovo più le istruzioni della confezione
it happens to me that they do not pair together and in the bluetooth the name touch two c5s appears twice which are paired with one of the earphones, how can I pair them together thanks.
P.S. I can no longer find the package instructions</em>
bravi ma manca i problemi che posso avere :
mi succede che non si abbinano assieme e nel bluetooth appaiono 2 volte il nome touch two c5s le quali sono abbinate a uno dei auricolari, como posso abbinarli assieme grazie .
P.S. nontrovo più le istruzioni della confezione
How do I pair the Touch Two C5 earbuds together when they appear as two separate Bluetooth devices?
When your Touch Two C5 earbuds appear as two separate devices in your Bluetooth list, it means they have entered "Single Earbud Mode" and are not synced to each other. To pair them together again, follow these steps:
If they still do not sync, try putting them back into the charging case to reactivate them, then remove them at the exact same time to trigger the automatic pairing process.
Read the full Q&A page
These earbuds suck! Only the left one charges most of the time. I want a new pair!
I’m having the same problem as stefano August 27, 2021 where I would see two instances of the earbuds in the Bluetooth devices list. I can only pair each bud individually with playback being on L or R but not both. Do you have instructions to “re-pair” the buds. Thank you.
these suck bruh, it wont connect to my shit and it has two buttons that arent even beneficial, if i wanna see the time ill check a clock
How do I troubleshoot connection issues with my Touch Two C5 earbuds?
If your Touch Two C5 earbuds are not connecting, please follow these troubleshooting steps from the manual:
Regarding the buttons, these earbuds use a touch-sensitive surface rather than physical buttons. A single click on the touch area handles play/pause or answering calls, while a long press for 2 seconds adjusts the volume.
Read the full Q&A page
my bluetooth headphones work all the only thing that fails is when I make a call but I listen but they don’t listen to me they will know what is the reason
mis audifonos bluetooth funcionan todo lo u ico que falla es cuando ago una llamada pero yo escucho pero ellos no em escuchan sabrán.cual es el motivo
mis audifonos bluetooth funcionan todo lo u ico que falla es cuando ago una llamada pero yo escucho pero ellos no em escuchan sabrán.cual es el motivo
How do I troubleshoot connection issues with my Touch Two C5 earbuds?
my bluetooth headphones work all the only thing that fails is when I make a call but I listen but they don't listen to me they will know what is the reason
mis audifonos bluetooth funcionan todo lo u ico que falla es cuando ago una llamada pero yo escucho pero ellos no em escuchan sabrán.cual es el motivo
I have a problem that the Touch Two C5S earphones do not match and indeed appear twice the device name concerning the 2 earphones according to what I activate.
try it all, there is no way to reset the box containing the earphones
Thank you
ho un problema che gli auricolari Touch Two C5S non si abbinano e anzi appaiono 2 volte il nome dispositivo che riguardano ai 2 auricolari assecondo di quello che attivo .
lo provate tutte, non c’è un modo per resettare il la scatola contenete gli auricolari
grazie
try it all, there is no way to reset the box containing the earphones
Thank you<e/em>
ho un problema che gli auricolari Touch Two C5S non si abbinano e anzi appaiono 2 volte il nome dispositivo che riguardano ai 2 auricolari assecondo di quello che attivo .
lo provate tutte, non c'è un modo per resettare il la scatola contenete gli auricolari
grazie
How do I fix the Touch Two C5S earbuds when they appear as two separate devices and won't pair together?
When your Touch Two C5 earbuds appear as two separate devices in your Bluetooth list, it means they have entered "Single Earbud Mode" and are not synced with each other. To fix this and pair them together, follow these steps:
Note: If they still appear twice, ensure you have removed the PET insulation film from the charging contacts of both earbuds and that they are fully charged. If one earbud is still acting independently, try long-pressing the touch surface for 4 seconds to shut it down, then power it back on while the other is active to trigger the search mode.
Read the full Q&A page
Hi. Have you tried cleaning the earbud grill? I was on here trying to find out how to reset the buds when I realized that it could just be a build-up of earwax. I pulled the gel off and looked at the grill with a loupe and voila! it was caked on. I cleaned it and now they are balanced again.
How do I fix the Touch Two C5S earbuds when they appear as two separate devices and won't pair together?
Hi. Have you tried cleaning the earbud grill? I was on here trying to find out how to reset the buds when I realized that it could just be a build-up of earwax. I pulled the gel off and looked at the grill with a loupe and voila! it was caked on. I cleaned it and now they are balanced again.
hello, one of the headphones has a low volume compared to the other.
bonjour, un des écouteurs a un volume bas par rapport a l’autre.
bonjour, un des écouteurs a un volume bas par rapport a l'autre.
Why is the volume lower in one of my Touch Two C5 earbuds compared to the other?
If you are experiencing lower volume in one earbud on your Touch Two C5, please try the following troubleshooting steps based on the manual:
If the issue persists, it may be a hardware malfunction or a low battery state in one specific bud; ensure both are fully charged until the LED turns blue.
Read the full Q&A page
They no longer connect to each other, two connections come out on the phone and consequently either one or the other works
Non si connettono più tra loro escono due connessioni sul telefono e di conseguenza funziona o l’uno o l’altro
Non si connettono più tra loro escono due connessioni sul telefono e di conseguenza funziona o l’uno o l’altro
How do I fix the Touch Two C5 earbuds when they won't connect to each other and show up as two separate Bluetooth devices?
When your Touch Two C5 earbuds appear as two separate connections on your phone, they have entered "Single Earbud Mode" and need to be resynced to each other. Follow these steps to restore the stereo connection:
Read the full Q&A page
Same problems as the others, the cel suddenly finds two earphones with the same name and they just alternate, they don’t go together anymore how can I solve this problem?
Stesso problemi degli altri ,il cel all’improvviso trova due auricolari con stesso nome e vanno solamente alternati ,non vanno più assieme come posso risolvere questo problema?
Stesso problemi degli altri ,il cel all'improvviso trova due auricolari con stesso nome e vanno solamente alternati ,non vanno più assieme come posso risolvere questo problema?
How can I fix my Touch Two C5 earbuds when they appear as two separate Bluetooth devices and only play one at a time?
This issue occurs when the earbuds lose their internal pairing and enter "Single Earbud Mode" independently. To resolve this and get them to work together again, follow these steps:
If the problem persists, you may need to perform a "Rematch" as suggested in the Troubleshooting Guide by placing them back in the case to power them off and taking them out again at the exact same time.
Note: If you are following these steps and still see two separate names, ensure you have removed the PET insulation film from the charging contacts of both earbuds as mentioned in the Quick Start Guide.
Nota per l'utente: Questo problema si verifica quando gli auricolari si scollegano tra loro. Elimina i nomi Bluetooth dal telefono, estrai entrambi gli auricolari contemporaneamente e attendi che dicano "Left channel, Right channel" prima di riassociarli al telefono.
Disclosing uncertainty: The manual does not provide a specific button-sequence factory reset, so the standard re-pairing procedure is the primary solution provided.
Read the full Q&A page
I have trouble connecting the left piece. I called for the replacement. The replacement also seems to be faulty. Only the Right earbud is powering on. The left earbud is not showing any activity even after long touch on the earbud. I charged both the earbuds, but only the right earbud is getting connected.
Does anything need to be taken care of?
Kindly guide.
Does anything need to be taken care of?
Kindly guide.
I have trouble connecting the left piece. I called for the replacement. The replacement also seems to be faulty. Only the Right earbud is powering on. The left earbud is not showing any activity even after long touch on the earbud. I charged both the earbuds, but only the right earbud is getting connected. Does anything need to be taken care of? Kindly guide.
It sounds like you're experiencing a persistent issue with the left earbud of your Touch Two C5, even with a replacement. Here are some troubleshooting steps based on the manual that might help, focusing on ensuring the left earbud is properly powered and paired:
If the left earbud isn't powering on, it won't be able to participate in this pairing process.
Given that you've already received a replacement with the same issue, it's possible there might be a more fundamental problem with the batch or a very specific step being missed during the initial setup that prevents the left earbud from activating. If none of these steps resolve the issue, and especially if the left earbud shows no LED activity even after being placed in the charging case, it strongly suggests a defect.
Read the full Q&A page
How do I change the time from 24 hour to 12 hour?
How do I change the time from 24 hour to 12 hour format?
Based on the provided manual for the Touch Two C5 Stereo Headset, there are no instructions or features mentioned regarding a clock or time display. The manual focuses on audio playback, touch controls, and charging the earbuds.
While some versions of the C5 charging case include a digital battery indicator (labeled as "battery indicator" on page 3), it typically only displays the battery percentage and does not function as a clock. If your specific model has a clock display that is not covered in this manual, it may be a different hardware revision. However, for the standard Touch Two C5, there is no setting to toggle between 12-hour and 24-hour time formats as the device does not track time.
Read the full Q&A page
Same problem. Two separate bluetooth earbuds… 🙁
How do I fix my Touch Two C5 earbuds when they appear as two separate Bluetooth devices and won't pair together?
When your Touch Two C5 earbuds appear as two separate Bluetooth devices, it means they have lost their mutual pairing and are in "Single Earbud Mode." To fix this and restore stereo sound, follow these steps:
If they still appear separately, ensure you have removed the PET protective insulators from the charging contacts and that both earbuds are fully charged. If the issue persists, try placing both back in the case to "activate" them and then removing them at the exact same time.
Read the full Q&A page
Hello.
Mine have been in the charging case for over 12 hours and when I open the case there is no blue light.
They will not connect to my Iphone.
Mine have been in the charging case for over 12 hours and when I open the case there is no blue light.
They will not connect to my Iphone.
Why are my Touch Two C5 earbuds not showing a blue light or connecting to my iPhone after charging for 12 hours?
Based on the Touch Two C5 manual, there are several reasons why your earbuds may not be showing a blue light or connecting after being in the case:
If the earbuds still do not show any lights or appear in your iPhone's Bluetooth list as "Touch Two C5," try cleaning the charging contacts on both the earbuds and the case with a dry cloth to ensure a good connection.
Read the full Q&A page
The earbuds don’t seem to charge . The case goes to 100 percent but ear buds won’t light up or turn on . What do I do
Why are my earbuds not charging or turning on even though the case is at 100%?
If your Touch Two C5 earbuds are not charging or turning on while the case shows 100% battery, please try the following troubleshooting steps:
Read the full Q&A page
The earphones do not charge when inserted into the charging box
Los auriculares no se cargan al insertarlos en la caja de carga
Los auriculares no se cargan al insertarlos en la caja de carga
Why are my earphones not charging when placed in the charging box?
If your Touch Two C5 earbuds are not charging when placed in the charging box, please check the following troubleshooting steps based on the manual:
Read the full Q&A page
Have only had C5 Wireless earbuds for a few month and not used a lot. Right earbud is now not working and will not charge
Why is my right Touch Two C5 earbud not working or charging?
Based on the Touch Two C5 manual, if your right earbud is not working or charging, please try the following troubleshooting steps:
If the earbud still does not respond or charge after ensuring it is seated correctly, the battery may have reached a state of deep discharge if left unused for a long period, or there may be a hardware failure. Note that the manual warns that attempting to open or repair the earbuds will cancel the warranty.
Read the full Q&A page
My touch two c5 earpods won’t sync with each other and they both have two seperate names on my Bluetooth settings
I’ve tried everything but it won’t connect to each other
I can literally listen to two different songs on each earbud and it’s very Annoying
Please send me an email or something on how to sync them together or reset it
Thank you
I've tried everything but it won't connect to each other
I can literally listen to two different songs on each earbud and it's very Annoying
Please send me an email or something on how to sync them together or reset it
Thank you
How do I sync my Touch Two C5 earbuds together when they appear as two separate Bluetooth devices?
To sync your Touch Two C5 earbuds together so they function as a pair, follow these steps based on the manual's pairing instructions:
If they still appear as two separate devices, it means they are stuck in "Single Earbud Mode." Ensure you are removing both from the case simultaneously to trigger the dual-pairing sequence.
Read the full Q&A page
I have the C8 and they fucking suck. Keep disconnecting when I have phone in my pocket smh
Why do my Touch Two C8 earbuds keep disconnecting when my phone is in my pocket?
While you are using the C8 model, the troubleshooting steps for the C5 model address similar connectivity issues. According to the manual, a "Bad signal" or "Intermittent" connection is often caused by being too far from the device or outside interference.
To improve the connection when your phone is in your pocket, try the following:
Note: As this manual is specifically for the C5 model, there may be slight hardware differences in the C8, but the Bluetooth range limitations (typically 10M/33ft without obstructions) remain a standard factor.
Read the full Q&A page
I only use one bud at time mostly the left side.
However occasionally would like to use the right side only, but it often stops being linked.
However occasionally would like to use the right side only, but it often stops being linked.
How do I troubleshoot the right earbud not linking when used in single earbud mode?
To use the right earbud alone or troubleshoot it when it stops linking, follow these steps for Single Earbud Mode:
If the signal remains intermittent, ensure the phone is close to the earbud and away from outside interference, as noted in the troubleshooting guide.
Read the full Q&A page
these earbuds are great work flawless with my android S21 phone have been having a difficult time trying to connect to my lenovo think pad T490S wont display connection in bluetooth list but I do like them stay in place very well good sound quality
John H.
John H.
How do I connect my Touch Two C5 earbuds to a Lenovo ThinkPad T490S laptop if they are not appearing in the Bluetooth list?
If your Touch Two C5 earbuds are not appearing in your Lenovo ThinkPad's Bluetooth list, it is likely because they are still actively connected to your Android S21 or are not in pairing mode. Follow these steps to resolve the issue:
Read the full Q&A page
Hello, I have these touch two c5 s headphones and I am not able to pair them… they have worked well for a while, but now the two headphones do not hear, they are independent. Someone who understands could give me a cable, how to reset it to the factory or any advice .Thanks
Hola,tengo estos auriculares touch two c5 s y no soy capaz de emparejarlos….han funcionado bien un tiempo,però ahora no se eschuchan los dos auriculares,van independiente.Alguien que entiende me podria echar un cable,como reiniciarlo de fabrica o cualquier consejo.Gracias
Hola,tengo estos auriculares touch two c5 s y no soy capaz de emparejarlos….han funcionado bien un tiempo,però ahora no se eschuchan los dos auriculares,van independiente.Alguien que entiende me podria echar un cable,como reiniciarlo de fabrica o cualquier consejo.Gracias
How do I pair my Touch Two C5 headphones, troubleshoot independent earbud operation, and perform a factory reset?
The provided manual offers instructions for connecting your Touch Two C5 earbuds to your phone and troubleshooting some common issues. However, it does not explicitly detail a factory reset procedure.
To connect your Touch Two C5 earbuds:
If your earbuds are working independently, it might be a pairing issue. The manual states that pairing to the phone is only required for the first time. After that, the earbuds should automatically connect to your phone when removed from the case. If they are not pairing together, you might try the following based on the troubleshooting section:
The manual does not provide specific instructions for a factory reset. If the above steps do not resolve the issue, you may need to contact the manufacturer's support for further assistance.
Read the full Q&A page
I just bought a pair of the C5 ear buds and I can’t get mine to turn on what so ever. and they have been on the charger all night also.
Why won't my Touch Two C5 earbuds turn on even after charging all night?
If your Touch Two C5 earbuds are not turning on after charging, please check the following common issues based on the manual:
If you have already removed the plastic covers and they still won't turn on, try cleaning the charging contacts with a dry cloth to ensure a solid connection.
Read the full Q&A page
If you lose one ear buds can get it replaced …Left
Can I get a replacement for a lost left earbud?
The provided manual for the Touch Two C5 does not contain specific information regarding the purchase of individual replacement earbuds or a replacement policy for lost components. Typically, these earbuds are sold as a complete set (1 pair) as listed in the "Packing details" on page 3.
To inquire about a replacement, you should contact the original seller or the manufacturer directly. If you are able to obtain a replacement left earbud, the manual notes on page 6 that the earbuds can be used in "Single Earbud Mode" or paired together by placing both in the charging case to allow them to find each other and pair automatically.
Please note that attempting to open or repair the earbuds yourself will void the warranty, as stated in the Safety Rules on page 2.
Read the full Q&A page
my earbud has been making a crackling sound and has started sounding worse even though I have been cleaning them and taking care of them they just decide to make my music sound shit whenever I connect them to my Chromebook I was wondering if I had turned off some sort of noise canceling and if there was a way to return it on if that was the problem my earbuds also for some reason don’t like when I move my head down or sideways when they are connected to my Chromebook.
How can I fix crackling audio and connectivity issues on my Touch Two C5 earbuds when using a Chromebook, and is there a noise-canceling feature?
Based on the Touch Two C5 manual, here are the steps to address your audio and connectivity issues:
If the crackling persists after a full charge and re-pairing, the manual suggests the cause may be environmental interference or the source device being too far away.
Read the full Q&A page
Is there any way to turn off the lights on the ear buds
How do I turn off the LED lights on the Touch Two C5 earbuds?
Based on the Touch Two C5 User Manual, there is no specific touch command or setting to manually turn off the LED lights while the earbuds are in use. The LEDs serve as status indicators for pairing and charging.
According to the manual:
If you wish to turn the earbuds off entirely (which will also turn off the lights), you can long press the left ear touch area for 4 seconds or place them back into the charging case.
Read the full Q&A page