WRIGHTMASTER MLS710 Drywall Sander

Overview
The MLS710 drywall sander is an electric sander intended for sanding and smoothing drywall surfaces and preparing them for finishing. It features electronic speed control and dust extraction via a vacuum system connection.
Specifications
| Model | MLS710 |
|---|---|
| Voltage | 220-240V~ 50/60Hz; 120V~ 60Hz |
| Power | 710W |
| Current | 6A |
| Rotation speed | 800–1800 rpm |
| Round sanding pad | 215 mm (8.5 inches) |
| Noise (LpA / LwA) | 84.4 / 92.4 dB(A) with K=3.0 dB |
| Vibration (rear handle) | ah,DS = 0.731 m/s² |
| Vibration (auxiliary handle) | ah,DS = 2.303 m/s² |
| Vibration uncertainty | K = 1.5 m/s² |
| Net weight | 3.6 kg (7.8 lbs) |
Components
- Round sanding head
- handle
- Motor housing
- Aluminium pipe
- Folding lock
- Main handle
- Electronic speed control
- Lock-on button
- Wrench
- Switch
- Round sanding pad(hook&loop system)
- Extension shaft
- Rear handle
- Vacuum hose
- Stand
- Connector(pre-assembled)(38mm)
- Suction power adjustment ring
- Vacuum adaptor(pre-assembled) (47mm)
- Vacuum adaptor(pre-assembled) (35mm)
- Hex wrench S5
- Round sanding disc

Quick Setup & Use
- Prepare dust extraction: Insert vacuum hose (P) into the end of the tool handle as illustrated. If needed, connect the vacuum hose to the vacuum adaptor (47 mm) and then to an industrial vacuum cleaner. Adjust suction airflow using the suction power adjustment ring (P3).
- Install the sanding disc/pad: Ensure the sanding disc is suited to the task. For the round sanding head, position the sanding disc centered on the sanding pad and press it so holes align with the extraction holes in the pad. (The manual also describes releasing/locking the sanding pad using a wrench/bolt for replacement.)
- Optionally adjust work height: Loosen the wrench first, then insert the extension shaft into the main handle and adjust length if necessary, observing the “max 1.65 m” marking.
- Start operation: Turn on the vacuum cleaner first, then turn on the sander using switch J.
- Adjust speed and sand: Use electronic speed control (G) to select a suitable speed. Keep the sander moving; avoid staying too long in one spot to prevent marks.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING:
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY
- Keep work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
- Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions.Water entering a power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
- When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
PERSONAL SAFETY
- Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
POWER TOOL USE AND CARE
- Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
SAFETY INSTRUCTIONS FOR DRYWALL SANDER
- This power tool is intended to function
as a polisher. Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. - This power tool is not recommended for grinding, sanding, wire brushing or cutting off operations. Operations for which the power tool was not designed may create a hazard and cause personal injury.
- Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
- The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can fly apart.
- The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
- The arbour size of wheels, flanges, backing pads or any other accessory must properly fit the spindle of the power tool. Accessories with arbour holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
- Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pads for cracks, tear or excess wear, wire brushes for loose or cracked wires. If the power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no load speed for one minute. Damaged accessories will normally break apart during this test time.
- Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and a shop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtering particles generated by your operation. Prolonged exposure to high-intensity noise may cause hearing loss.
- Keep bystanders a safe distance away from the work area. Anyone entering the work area must wear personal protective equipment. Fragments of the workpiece or of a broken accessory may fly away and cause injury beyond the immediate area of operation.
- Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. A cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
- Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
BEFORE USE
- Before using the tool for the first time, it is recommended to receive practical information. Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected toa 220V supply)
- Use suitable detectors to find hidden utility lines or call the local utility company for assistance(contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipewill cause property damage or an electrical shock)
- Do not work with materials containing asbestos (asbestos is considered carcinogenic)
- Dust from materials such as paint containing lead, some wood species, minerals and metal may be harmful (contact with
or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable - Certain kinds of dust are classified as carcinogenic (such as oak and beech dust), especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable
- Follow the dust-related national requirements for the materials you want to work with
- Do not clamp the tool in a vice
- Use completely unrolled and safe extension cords with a capacity of 16 Amps(U.K.13 Amps)
AFTER USE
After switching off the tool, never stop the rotation of the accessory by a lateral force applied against it
USE
Shaft 2

- Fold the front and back parts together (2a).
- Push the folding lock E to the right position and keep the tip adjacent to the handle. (2b)
- Press the folding lock E towards the handle until the end. (2c) Unfold the handle by pushing the folding lock to the inside.
Replace sanding pad 3

- Insert the hex wrench (size 5) into the hexagonal screw bolt on the sanding block
- Hold the sanding pad firmly, and then turn the wrench counterclockwise to dismount the pad.
- Install the new sanding pad by tightening the bolt.
SANDING OPERATIONS
Once the machine and vacuum cleaner are set up and all safety measures and equipment are in place, begin by turning on the vacuum cleaner and then the machine. (lf you are using a vacuum cleaner with integrated switching, then simply turn themachine on.)
Round sanding head 6

- Begin sanding and carefully contact the work surface as lightly as possible-justenough to keep the sanding head flat against the surface.
- The pivot point in the sanding head allows the sanding disc to follow the contours ofthe work surface.
- The best technique is to use overlapping sweeps and keep the head in constant motion. Never stop too long in any one place, or there will be swirl marks. With experience, it will be very easy to create excellent results.
Maintenance/Service
Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components, which could cause a serious hazard. We recommend that all tool service be performed by MAXXT Service Team.To purchase repair parts in North America, you can directly visit www.hyperfit-tools.ca. For other countries, please contact service@ maxxt-tech.com for purchasing. Do not attempt to clean ventilation slots by inserting pointed objects through openings. disconnect the plug before cleaning.
ENVIRONMENT
Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries). In observance of the European Directive on waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
Documents / Resources
![]() | MLS710 Drywall Sander |
References
- User Manualmanual.tools
