Konica HEXAR RF Camera User Manual

Konica-LOGO

Konica HEXAR RF Camera

Konica-HEXAR-RF-Camera-PRODUCT

NAME OF PARTSKonica-HEXAR-RF-Camera-FIG (1)

  1. Hot Shoe
  2. ISO/Exposure Adjustment Dial
  3. Shutter Dial
  4. Shutter Dial Unlock Button
  5. Main Switch Lever
  6. Shutter Release Button
  7. Strap Attachment Clip
  8. Self-Timer Lamp
  9. Lens Attachment/Removal Button/Lens Index
  10. Finder Brightness Window
  11. Display Panel/Film Counter
  12. Viewfinder Window
  13. View Frame Switching Lever
  14. Rangefinder Window
  15. Viewfinder Eyepiece
  16. Cable Release Socket
  17. Back Cover Release Knob
  18. Manual Rewind Switch
  19. Film Check Window
  20. Back Cover
  21. Battery Chamber Cover
  22. Tripod Socket
Simplified Steps in Taking Pictures

For more detailed information, refer to the figure numbers provided.

  1. Insert the Batteries: Insert the batteries into the camera. (Fig. 2)
  2. Attach the Lens: Attach the lens to the camera. (Fig. 3)
  3. Load the Film: Open the back cover ⑳, insert the film roll, and close the back cover. (Fig. 13)
  4. Turn On the Camera: Turn the main switch lever ⑤ and set the index to “S”. (Fig. 5)
  5. Set the Exposure Mode: Turn the shutter dial ③ to set the exposure mode to “AE”. (Fig. 23)
  6. Adjust the Focus: Pull out the hood (a) and set the focus value (b). After composing the picture, turn the focusing ring (c) until the subject is sharply focused. (Figs. 17 and 23)
  7. Take the Picture: Press the shutter release button ⑥ halfway. The shutter speed will appear inside the viewfinder. Then press the shutter release button fully to take the picture. (Fig. 23)

Online Camera Manual Library

This manual is provided for reference and historical purposes. All rights reserved.

Copyright © M. Butkus, NJ.

  • This page may not be sold or distributed without the express permission of the producer.
  • I have no connection with any camera company.
  • If you wish to donate $3 to my camera manual website, please use the links below.

Donation Information

If you find this manual useful, please consider donating $3 to:

  • M. Butkus 29 Lake Ave. High Bridge, NJ 08829-1701
  • Please include your email address so I can thank you.
  • Most other places would charge $7.50 for an electronic copy or $18.00 for a printed Xerox copy.
  • Your donation helps purchase additional camera manuals and cover shipping costs.

Payment Options

If you use PayPal or wish to pay by credit card, visit the secure payment link on the website’s main page.

Preparations Before Taking Pictures

Using the Strap (Fig. 1)Konica-HEXAR-RF-Camera-FIG (2)The protective case (a) can be attached to the belt using the belt clip ⑦. Insert the adjustment strap (b) between the metal clip’s arms and squeeze the strap together to widen it. Then pull the strap through the opening in the belt clip. Finally, attach the strap by pulling it through the fastener and the hole in the lens cover. Use the protruding part of the strap’s plastic holder to press the manual rewind button ⑱.

Loading the Battery (Fig. 2)Konica-HEXAR-RF-Camera-FIG (3)Konica-HEXAR-RF-Camera-FIG (4)The camera will not operate without a battery. Turn off the main power switch before inserting new batteries.

  1. Insert a coin or similar object into the slot on the battery compartment cover ㉑ and turn it in the direction of the arrow to open the compartment.
  2. Insert the batteries into the battery compartment according to the illustration, ensuring that the positive (+) and negative (−) terminals face the correct directions. Close the compartment cover and return it to its original position.
    • If the batteries are inserted incorrectly, the camera will not function properly. Incorrect installation may also damage the camera.
  3. Turn on the main power switch ⑤ (Fig. 5) and check the display ⑪. If the black battery indicator lights up, the batteries are fully charged.
  4. Use two 3V lithium batteries (CR2).

Battery Indicator

  1. Sufficient Power: The battery symbol is black, indicating that sufficient power is available.
  2. Low Power: The battery symbol is two-thirds black and one-third white. Replace the batteries soon.
  3. Battery Discharged: The battery symbol is one-third black and flashes before becoming completely empty. No more pictures can be taken.

If the two-thirds battery symbol remains steady, there is sufficient power to finish the film before replacing the batteries.

Battery Replacement

  • When replacing the batteries, always turn off the main power switch first.
  • If film is loaded in the camera, replace the batteries quickly (within 30 seconds).

Attaching and Removing the Lens

  • The interchangeable lenses compatible with this camera are Konica M-Hexanon lenses with KM mounts.
  • Konica does not guarantee the correct operation or performance of other lenses used with this camera. Konica accepts no responsibility for damage caused by using other lenses.

Precautions When Removing and Attaching Lenses

  • Always turn off the main power switch before removing or attaching a lens.
  • When removing or attaching a lens, hold it correctly. Otherwise, attachment or removal may be difficult.
  • Prevent dirt and dust from entering the lens, and avoid touching or scratching its surfaces. Do not apply finger pressure to the lenses. The best practice is to keep the lens cover in place except when changing lenses.
  • Avoid strong light sources, such as sunlight, when removing or attaching a lens with film loaded in the camera. Never leave the camera in strong sunlight with the lens removed.

Attaching the Lens (Fig. 3)

  • Hold the lens with your entire hand (a). Align the markings on the lens (red dots) with the corresponding markings on the camera ⑨. Gently press the lens against the camera and turn it until you hear a click. Do not turn it any further.
  • Before attaching the lens, remove its rear protective cap and the camera’s lens mount cover.Konica-HEXAR-RF-Camera-FIG (5)

Camera Operating Instructions

If the lens cannot be attached to the camera, or if the alignment marks are not correctly aligned while the lens is in position, the lens cannot be locked into place.

Removing the Lens (Fig. 4)

  1. Hold the lens firmly with your entire hand, press the lens release button ⑨ on the camera, and turn the lens counterclockwise until it stops. Remove the lens by pulling it forward.
  2. The lens will release when the red alignment marks on the camera and lens are aligned.
  3. After removing the lens, always cover the lens with its rear protective cap and the camera with its lens mount cover.

Operating the Main Power Switch

  1. Operate the main power switch ⑤ to turn the camera on or off, select motor-driven photography (Fig. 6), or use the self-timer (Fig. 34).
  2. Turn the camera’s main power switch until you hear a click at the desired position.

Turning the Power On and Off (Fig. 5)

  1. Turn the main power switch ⑤ so that the index points to “S” (normal still photography). The camera will turn on. This is the normal position for taking pictures.
  2. The red @ mark is visible when the power is on.
  3. When the power is switched on, the frame counter and battery indicator appear on the display panel ⑪.
  4. To switch off the power, rotate the main power switch to the position shown in the diagram. Stop turning when you hear a click.
  5. After taking pictures, or when the camera will not be used for an extended period, turn off the power to avoid accidentally releasing the shutter.
  6. When the power is off, only the battery indicator remains visible on the display panel. The red mark is no longer visible.Konica-HEXAR-RF-Camera-FIG (6)

Operating the Camera in Motor-Drive Mode (Fig. 6)

  1. Turn the main power switch until it points to “C”.
  2. Press and hold the shutter release button ⑥ to take several pictures in succession.
  3. Release the button to stop taking pictures.
    • Maximum continuous shooting speed: 2.5 frames per second.
    • The actual shooting speed varies depending on shutter speed, film sensitivity, and battery charge level.

Display Panel (Fig. 7)

The display shows all liquid crystal indicators when the camera is switched on.

  • Battery indicator
  • Frame counterKonica-HEXAR-RF-Camera-FIG (7)

Liquid Crystal Display (LCD)

The camera’s display panel uses liquid crystal technology.

  • At high temperatures, the display becomes darker and responds more slowly at low temperatures.
  • Normal operation returns when the surrounding temperature returns to normal.

The Viewfinder (Fig. 8)

  • The indicator inside the viewfinder lights up when the power is switched on and the shutter release button ⑥ is pressed halfway.
  • The light meter remains active for approximately 15 seconds, then automatically switches off, causing the viewfinder indicators to disappear.
  • Pressing the shutter release button halfway again will reactivate the indicators.
  • The diagram shows all indicators illuminated.

Viewfinder Indicators

Indicator Description
A. LCD Indicators Display shutter speed or exposure warnings. See Figures 23 and 24.
B. Battery Charge Indicator Displays “125⚡” when the batteries installed in the flash unit are fully charged. See Figure 35.
C. Exposure Control Mark The +/− symbol illuminates when exposure compensation is adjusted. See Figure 30.
D. Frame See Figure 9.
E. Focusing Frame Frame used for focusing adjustment. See Figure 17.
Viewfinder Frame and Light Metering Area
  • This camera is equipped with viewfinder frames for 28 mm, 35 mm, 50 mm, 75 mm, 90 mm, and 135 mm lenses.
  • The frame changes depending on the lens being used (Fig. 9). The subject is positioned within the frame to compose the photograph.
  • The viewfinder frames automatically compensate for parallax (differences in viewing angle) based on the shooting distance and the area captured in the image.
  • The light metering area for each lens remains approximately the same, as shown by the blue dotted line in Figure 9.Konica-HEXAR-RF-Camera-FIG (8)

Manually Switching the Viewfinder Frame

  • By turning the frame selector switch ⑬, you can check the different shooting areas for various lens focal lengths without attaching a lens.
  • Press the frame selector switch ⑬ inward to display the frame (Fig. 10) used for 28 mm and 90 mm lenses. Set the switch vertically to display the frames for 50 mm and 75 mm lenses (Fig. 11). Move the switch outward to display the frames for 35 mm and 135 mm lenses (Fig. 12).Konica-HEXAR-RF-Camera-FIG (9)Konica-HEXAR-RF-Camera-FIG (10)

Loading the Film (Fig. 13)Konica-HEXAR-RF-Camera-FIG (11) Konica-HEXAR-RF-Camera-FIG (12)Use 35 mm (135 type) film in this camera. The camera automatically sets the film sensitivity (ISO 25–5000) when DX-coded film is loaded. If the film does not have DX coding, set the film sensitivity manually (see Fig. 15).

  1. Slide the back cover release button ⑰ upward and turn it in the direction of the arrow to open the back cover ⑳.
    • When the back cover is open, return the release button ⑰ to its original position.
    • Make sure no dust enters the camera.
    • When loading film for the first time, remove the thin protective film inside the camera.
  2. Insert a new film cartridge into the film chamber. Pull out the film leader while keeping the cartridge in position.
  3. Pull the film leader forward to the “FILM TIP” mark inside the camera.
  4. Close the back cover securely.
    • When you turn the main power switch on, you will hear the motor operating, and the film will automatically advance.
    • With the main power switch on, press the shutter release button.
    • Turn on the main power switch and press the shutter release button once when using film without DX coding.
  5. If the film advances correctly, “1” will appear on the display panel.
    • If the film does not advance correctly, “0” will flash on the display panel (Fig. 14). Open the back cover again and reload the film.Konica-HEXAR-RF-Camera-FIG (13)

Shutter Warnings

  • The shutter is a precision component. Never touch it with your fingers, and ensure that the film leader does not come into contact with or press against it. Never use the shutter when the film cover is attached to the shutter.
  • When using an air blower to clean the camera, avoid blowing too strongly, as this may bend or otherwise damage the shutter. Never use compressed-air canisters for cleaning.

Setting the Film Sensitivity (Fig. 15)

Use this setting when loading film without DX coding or when you want to change the film sensitivity from the value indicated by the DX code.

  1. Lift and turn the ISO/Exposure Control Dial ② to set the sensitivity of the loaded film. Align the film sensitivity indicator with the index mark.
    • Film sensitivity can be adjusted in one-third-stop increments from ISO 6 to ISO 6400.
  2. To return to the DX-coded film sensitivity setting, align the index mark with “DX”.
    • If the loaded film does not have DX coding and the ISO/Exposure Control Dial is set to DX, all photographs will be exposed as though ISO 100 film were loaded.
    • The selected sensitivity setting remains active until it is changed again.
    • If the film sensitivity is set to your preferred ISO value, the camera will use that manually selected setting even when DX-coded film is loaded.Konica-HEXAR-RF-Camera-FIG (14)

Changing the Shutter Speed Dial (Fig. 16)

The exposure can be adjusted according to the intended photography conditions.

  1. Turn the shutter speed dial ③ to change the exposure mode or manually select the shutter speed.
  2. Rotate the dial until you hear a click, indicating that it has reached the selected position.
  3. The shutter speed dial locks when set to AE or AEL. It cannot be turned to another position until the lock release button ④ is pressed while rotating the shutter speed dial.

The following exposure modes are available:

  1. Aperture-Priority AE Photography: See Fig. 23.
  2. Shutter Speed Photography: See Fig. 26.
  3. AE Lock Photography: See Fig. 31.
  4. Bulb Photography: See Fig. 32.

Focusing (Fig. 17)

  • Focusing is performed using the rectangular area in the center of the viewfinder (Fig. 17).
  • There are two focusing methods. Choose the method best suited to the shooting conditions.
  • To focus on the desired subject, position your eye at the center of the viewfinder eyepiece ⑮ and locate the subject through the viewfinder.Konica-HEXAR-RF-Camera-FIG (15)

Split-Image Focusing Method (Fig. 18)

  • This is the most commonly used focusing method.
  • When photographing people, focus on their eyes.
  • Look through the viewfinder and turn the focusing ring until the two split images align and form one complete image.
    • Fig. 18-1: The split images are not aligned.
    • Fig. 18-2: The split images are correctly aligned, indicating proper focus.

Vertical Alignment Focusing Method (Fig. 19)

When photographing the edges of a subject or vertical objects, such as building corners or towers, align the vertical lines in the viewfinder.

  1. Look through the viewfinder and locate the vertical subject lines, as shown in Fig. 19-1.
  2. Rotate the focusing ring until the lines join correctly in the rectangular focusing area, as shown in Fig. 19-2.Konica-HEXAR-RF-Camera-FIG (16)

Removing the Film (Fig. 20)

  1. When the film reaches its end, it automatically rewinds into the cartridge.
  2. Rewinding stops automatically when it is complete, and “0” flashes on the frame counter. Open the back cover and remove the film.
  3. Store the exposed film in a location protected from direct sunlight.
  4. It is recommended to have the film developed as soon as possible after exposure.
  5. The film can be rewound until its leader remains outside the cartridge. Immediately after rewinding finishes and stops completely, “1” appears in the frame counter for approximately one second before “–” is displayed (Fig. 21). If you open the back cover at this point, the film leader will remain outside the cartridge. Take care not to reuse the same film accidentally.
  6. Film rewinding can be temporarily interrupted. If the main power switch is operated during rewinding, the power turns off and the rewinding process stops. Turn the power on again to continue.

This feature is useful when taking photographs at events such as weddings, where you may need to avoid motor noise during important moments.Konica-HEXAR-RF-Camera-FIG (17) Konica-HEXAR-RF-Camera-FIG (18)

Manual Film Rewinding (Fig. 22)

To rewind the film before reaching the end of the roll:

  1. Locate the manual film rewind button ⑱.
  2. Use the tip of the camera strap’s plastic holder to press the rewind button.
  3. The film will begin rewinding automatically into the cartridge.Konica-HEXAR-RF-Camera-FIG (19)

Basic Photography

Aperture-Priority AE Photography (Fig. 23)

This mode automatically adjusts the shutter speed according to the selected aperture (F-number). It is particularly useful when you want to control the depth of field by keeping the aperture at a fixed setting.

  1. Turn on the power (Fig. 5), rotate the shutter speed dial ③, and set the exposure mode to AE.
  2. Remove the lens cap (a), rotate the aperture ring (b), and select the desired F-number.
    • The shutter speed is automatically adjusted according to the selected aperture.
  3. Look through the viewfinder ⑮ and rotate the focusing ring (c) until the subject is in focus.
  4. Press the shutter release button ⑥ halfway to activate the indicators inside the viewfinder. The automatically selected shutter speed (correct exposure value) will be displayed.
    • The light meter remains active for approximately 15 seconds before switching off automatically and causing the indicators to disappear. Press the shutter release button halfway again to reactivate them.
    • AE Lock can also be used. See Fig. 31.
  5. Press the shutter release button fully to take the picture. The film will automatically advance by one frame.Konica-HEXAR-RF-Camera-FIG (22)

Exposure Warnings

If the shutter speed is outside the available range, “4” or “4000” will flash (Fig. 24). Adjust the aperture setting.

  1. If “4” flashes: The camera is receiving insufficient light. Select a larger aperture (lower F-number). If the shutter speed differs from the correct exposure value by more than half a second, “4” will flash slowly.
  2. If “4000” flashes rapidly: The camera is receiving too much light. Select a smaller aperture (higher F-number).
    • When two shutter speed values illuminate continuously at the same time, the actual shutter speed lies between those two values (Fig. 25).Konica-HEXAR-RF-Camera-FIG (23)Konica-HEXAR-RF-Camera-FIG (24)Konica-HEXAR-RF-Camera-FIG (25)

Manual Photography (Fig. 26)

Manual photography allows you to select any combination of aperture and shutter speed. This mode makes it easier to intentionally overexpose or underexpose photographs.

  1. Turn on the camera and rotate the shutter speed dial ③ to select the desired shutter speed.
    • If the shutter speed dial is locked, press and hold the shutter speed lock release button ④ while rotating the dial.
  2. Remove the lens cap (a) and rotate the aperture ring (b) to select the desired F-number.
  3. Look through the viewfinder ⑮ and rotate the focusing ring (c) until the subject is in focus.
  4. Press the shutter release button halfway to activate the indicators inside the viewfinder. The shutter speed indicator (A) will illuminate.
    • Indicator (B) will light continuously without flashing, indicating the correct shutter speed for the selected aperture and film sensitivity.
    • However, photographs can still be taken using the manually selected aperture and shutter speed.
    • To obtain the exposure indicated as correct by (B), adjust the aperture or shutter speed until both indicators display the same value.
    • When the illuminated indicators align at (C), normal exposure can be achieved.
  5. Press the shutter release button fully to take the photograph. The film will automatically advance by one frame.

Manual Exposure Indicators

  • If the selected shutter speed and the correct exposure value differ by less than half a second, the “4” indicator inside the viewfinder will flash slowly.
  • If “4” or “4000” flashes rapidly, the shutter speed is outside the camera’s available range. Adjust the aperture setting to obtain the correct exposure.
  • In manual mode, you can intentionally change the indicator from flashing to continuously illuminated to overexpose or underexpose photographs according to your personal preference.

Advanced Operation

Depth of Field

When you focus on a subject, an area in front of and behind the subject also appears sharp. This area is called the depth of field. A larger area of sharpness means greater depth of field, while a smaller area means shallower depth of field. Depth of field can be manually controlled in the following ways:

  1. Aperture Setting: A higher F-number produces greater depth of field. A lower F-number produces shallower depth of field.
  2. Lens Focal Length: At the same F-number, a shorter focal length provides greater depth of field, while a longer focal length provides shallower depth of field.
  3. Subject Distance: The farther you are from the subject, the greater the depth of field. The closer you are, the shallower the depth of field.
  4. Focus Position: Depth of field extends both in front of and behind the focused subject.

Figure 27 provides an example photograph demonstrating how depth of field works.Konica-HEXAR-RF-Camera-FIG (26)

Checking Depth of Field

  • The depth of field can be determined using the depth-of-field scale marked on the lens.
  • The numbers on both sides of the lens aperture scale indicate different F-numbers. These markings correspond to the distance scale, allowing you to estimate the area that will appear acceptably sharp.

How to Read the Depth-of-Field Scale (Fig. 28)

  • For example, suppose you are using a 50 mm F2 lens, the focusing distance is set to 5 meters, and the aperture is set to F8.
  • By reading the distance scale between the two F8 markings (marked “8” on either side of the index), the depth-of-field range extends from approximately 3.4 meters to 9.7 meters.
  • Subjects within this distance range should generally appear sharp.Konica-HEXAR-RF-Camera-FIG (27)

Infrared Photography (Fig. 29)

When taking infrared photographs, the focusing position must be adjusted to compensate for the difference between infrared and visible light.

  1. Move the focusing distance corresponding to your subject from the normal index mark to the red infrared index line.
  2. For example, if the focusing ring is set to 5 meters, rotate the distance scale so that the 5-meter marking aligns with the red infrared line instead of the normal index.
    • Infrared photography requires infrared film and an appropriate filter. For more detailed instructions, consult the documentation supplied with the infrared film.
    • The 90 mm F2.8 KM-mount M-Hexanon lens does not have an infrared index marking. Consult the instructions supplied with the 90 mm F2.8 lens for additional information.

Photography with Exposure Compensation

  • Incorrect exposure can occur when photographing subjects against strong backlighting or when there is an extreme difference in brightness between the main subject and its surroundings.
  • In these situations, exposure compensation can help achieve the desired exposure.
  • There are two methods of exposure compensation (see Figures 30 and 31).

Using the Exposure Compensation Dial (Fig. 30)Konica-HEXAR-RF-Camera-FIG (28)

In both aperture-priority AE photography and manual photography, the standard exposure value can be adjusted so that exposure compensation is displayed in the viewfinder.

  1. Rotate the exposure compensation dial ② to align the index mark with the desired exposure compensation value.
  2. Exposure compensation can be adjusted in one-third-stop increments from −2 EV to +2 EV.

Exposure Compensation (Continued)

  • When using film with a sensitivity of only ISO 6, exposure compensation can be adjusted from 0 to +2 EV. For ISO 12 film, the compensation range is −1 to +2 EV.
    1. If the exposure compensation dial is set to any value other than “0”, the +/− indicator will illuminate in the viewfinder to show that exposure compensation is active.
    2. Normally, the exposure compensation dial should remain at “0”. After taking photographs with exposure compensation, remember to return the dial to “0”.
  • In aperture-priority AE photography, exposure compensation adjusts the shutter speed.

Exposure Compensation for Different Lighting Conditions

  • Bright Backgrounds: When a bright background dominates the photograph, such as a backlit subject, a clear blue sky, or a subject near a window, the main subject may become underexposed and appear as a dark silhouette. Increase exposure compensation between +1/3 EV and +2 EV. This function can also be used to make dark areas of buildings appear brighter and improve contrast in bright regions.
  • Dark Backgrounds: When the subject is positioned against a dark background, such as a person standing in front of a black wall under a spotlight, the subject may become overexposed and appear too bright. Set exposure compensation between −1/3 EV and −2 EV to reduce exposure. This function can also be used to intentionally create darker images or photograph backgrounds with subdued skies.
  • Exposure Bracketing: If you are unsure of the correct exposure, take several photographs while adjusting exposure compensation in one-third-stop increments, either positive or negative, for each photograph.

Using AE Lock (Fig. 31)

AE Lock is an exposure compensation method used with aperture-priority AE photography (Fig. 23). This function is useful when photographing several moving subjects in succession or taking pictures under backlit conditions while maintaining a fixed exposure.

  1. Turn the shutter speed dial ③ to the “AEL” position.
  2. Look through the viewfinder, position the main subject inside the focusing area, and adjust the focus.
  3. Press the shutter release button halfway to allow the camera to measure the exposure and activate AE Lock.
  4. Continue holding the shutter release button halfway while recomposing the photograph. Then press the button fully to take the picture.

AE Lock Operation

  • The shutter speed remains fixed at the recorded exposure value, even when the background changes.
  • The camera maintains AE Lock as long as the shutter release button remains pressed halfway. Releasing the button cancels AE Lock.
  • When taking several consecutive photographs with AE Lock set for a particular lighting condition, all images will use the same exposure even if the background changes.
  • AE Lock is useful when photographing subjects outside the camera’s normal exposure metering range.
  • The camera records the shutter speed when AE Lock is activated. If the focus is changed after AE Lock has been applied, the exposure value will change.Konica-HEXAR-RF-Camera-FIG (29)

Bulb Photography (Fig. 32)

Use this function when taking photographs with shutter speeds longer than 1 second, such as nighttime scenes or photographs of the night sky. To prevent camera shake, mount the camera on a tripod or place it on another stable surface. Use a commercially available cable release.

  1. Turn the shutter speed dial ③ to the “B” position.
  2. Set the aperture, focus on the subject, and take the photograph.
  3. The shutter remains open, and the film continues to be exposed for as long as the shutter release button is held down.
  4. If the shutter speed dial is locked, press and hold the shutter speed lock release button ④ while rotating the shutter speed dial.

Cable Release (Fig. 33)

  • Use a commercially available cable release by attaching it to the cable release socket ⑯.
  • When using a cable release, you cannot press the shutter release button halfway to activate AE metering. First, press the shutter release button halfway with your finger, adjust the exposure and focus, then attach the cable release to its socket and press it to take the photograph.Konica-HEXAR-RF-Camera-FIG (30)

Self-Timer (Fig. 34)

A tripod is recommended to prevent camera shake. Always use a tripod when operating the self-timer to avoid blurred photographs.

  1. Turn the main power switch ⑤ and align the index with the self-timer symbol.
  2. Focus on the subject and press the shutter release button. The self-timer starts, and the photograph is taken after approximately 10 seconds.
  3. The self-timer indicator remains illuminated for seven seconds and then flashes for three seconds.
  4. The light meter activates when the shutter release button is pressed, so position yourself behind the camera before pressing the button.
  5. The self-timer cannot be used when the exposure mode is set to “B” (Bulb Photography).
  6. Turn the main power switch to another position to cancel the self-timer function.
  7. When using the self-timer with flash photography, make sure the flash is fully charged before pressing the shutter release button.
  8. After finishing self-timer photography, turn the main power switch to OFF, S, or C. If the switch remains in the self-timer position, the next photograph will also be taken using the self-timer.

Flash Photography

Flash photography is recommended when taking pictures indoors or outdoors at night. Flash is particularly useful when photographing people in shadow or when they are positioned against a bright background.

Flash Safety Precautions

  • Never fire the flash directly into someone’s eyes, especially those of small children, as this may cause eye injury.
  • Do not aim the flash at the driver of a vehicle while taking photographs, as this could cause an accident.
  • Do not use the flash if its surface is dirty or covered by a hand or another object. The high heat generated by the flash may damage the flash unit or discolor the image. Before taking pictures with flash, clean the flash surface and make sure it is not obstructed.

Taking Pictures with the Compatible HX-18W Flash

  • With the HX-18W flash, you can choose between automatically controlled flash output and full flash output.
  • Additional flash accessories, including the HX-18W flash specifically designed for this camera, can be purchased separately.

Photography with Automatically Controlled Flash / Aperture-Priority AE Photography (Fig. 35)Konica-HEXAR-RF-Camera-FIG (31)

  1. Loosen the flash locking screw (a) and slide the HX-18W flash into the camera’s accessory shoe ① until it stops. Then tighten the flash locking screw securely.
    • Never use anything other than the flash locking screw to secure the flash in position.
  2. Turn on the camera and set the flash power switch to either AUTO-1 or AUTO-2. Focus on the subject and set the camera’s shutter speed dial to AE or AEL.
    • Choose AUTO-1 or AUTO-2 according to the film sensitivity and the distance to the subject.
    • For additional information, consult the instructions supplied with the flash.
  3. In aperture-priority AE photography, the shutter speed is automatically set to 1/125 second.
  4. When the flash battery is fully charged, “125⚡” appears in the viewfinder.
  5. If you plan to take several photographs in quick succession, check whether the flash can fire repeatedly at short intervals before beginning photography.
Automatic Flash Exposure / Manual Photography
  1. Select either AUTO-1 or AUTO-2, following the same procedure used for aperture-priority AE flash photography (Fig. 35).
  2. Check the indicators in the viewfinder and select the correct shutter speed.
    • The camera cannot synchronize with the flash at shutter speeds faster than 1/125 second.
  3. Check the flash readiness indicator to ensure the flash is fully charged, focus on the subject, and take the photograph.
    • To select flash settings other than AUTO-1 or AUTO-2, set the flash power switch to FULL. Determine the correct aperture using the formula below.

Formula for the Correct Aperture

  • [ text{Aperture (F-number)}=frac{text{Guide Number (GN)}}{text{Subject Distance (m)}} ]

Refer to the instructions supplied with the flash for guidance on film sensitivity and guide numbers.

Using the Konica HX-14 Flash (Sold Separately)The HX-14 operates in essentially the same way as the HX-18W.

  • Automatic flash exposure can be used by selecting position A, while full flash output is available by selecting P. FULL.
  • When using automatic flash exposure (position A), the aperture should be set to F4 with ISO 100 film.
  • The fully charged indicator (125⚡) does not illuminate in the viewfinder when position A is selected.

Using a Commercially Available Flash

  1. Set the shutter speed to 1/125 second or slower.
  2. Select the appropriate aperture (F-number).
  3. Determine the correct F-number by referring to the instructions supplied with the flash.

Other Information

Compatible Accessories (Sold Separately)

  • A wide range of interchangeable lenses, flash accessories, and other camera accessories is available specifically for this camera.
  • Consult the retailer where the camera was purchased for further information about compatible accessories.

Lens with Adjustable Diopter Correction

  • If required, replace the existing eyepiece lens with one that offers adjustable diopter correction.
  • Available diopter correction values include +2, +1, 0, −2, and −3.
  • These eyepiece lenses are sold separately.

Consult the retailer where the camera was purchased for more information about these accessories.

Documents / Resources

PDF thumbnailHEXAR RF Camera
User Manual · Konica, HEXAR RF, Camera, Photography

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.