COXO Rechargeable Motion Sensor Light User Manual

简要概述

本灯具具备常亮与三种感应模式(夜间感应/全天感应/关闭),可通过按键切换模式、循环光色并调节亮度。首次使用前需先充满电。

规格参数

充电电压 DC 5V / 1A
充电接口 Type-C
充电指示 红灯亮:充电中;绿灯亮:已满电
感应范围 120°(以探头中心为基准),3米内
断灯延时 人离开感应区域后约25秒自动熄灭

快速上手

  1. 首次使用前先将电量充满。
  2. 安装:清洁并擦干安装位置表面;将金属片放到灯背面找到内置磁铁位置点;撕掉胶贴并粘到安装位置;安装完成后灯可吸附在金属片上并可取下或固定。
  3. 开机/切换模式:初始为关闭;依次按1/2/3/4下可在常亮/夜间感应/全天感应/关闭之间循环切换(夜间感应进入前灯闪烁3下提示,全天感应进入前闪烁2下提示)。
  4. 调节:短按按钮可循环切换光色;长按按钮可调节亮度。

说明书

合格证 检验员:03

首次使用前请先将电量充满。

模式及其功能说明

常亮模式 ■ 灯持续亮,感应功能不生效,不会自动熄灭。
黑夜感应模式 ■ 只有光线不足且感应到人的情况下才会自动亮。 ■ 人离开感应区域后约25秒灯自动熄灭。 ■ 若人一直在感应区域内活动,灯持续亮。
全天感应模式 ■ 不管光线是否充足,灯感应到人就会自动亮。 ■ 人离开感应区域后约25秒灯自动熄灭。 ■ 若人一直在感应区域内活动,灯持续亮。

按键说明

■ 初始为关闭状态。 ■ 按第1下:常亮模式。 ■ 按第2下:黑夜感应模式。(灯闪烁3下提示,闪烁完后随即进入黑夜感应模式) ■ 按第3下:全天感应模式。(灯闪烁2下提示,闪烁完后随即进入全天感应模式) ■ 按第4下:返回至关闭状态,如此循环。
■ 短按:循环切换光色。 ■ 长按:调节亮度。

感应范围及其注意事项

感应范围:灯的感应范围是以探头为中心点的120°,3米内的区域。 但安装不当或感应探头附近有遮挡物的话会影响感应效果。

安装说明及其注意事项

【安装步骤】:

1、清洁并擦干安装位置表面。

2、将金属片放置于灯背面上移动,找到内置的磁铁位置点。

3、撕掉胶贴,将其粘到安装位置。

4、安装完成。(灯吸附在金属片上,可取下或固定。)

充电说明

  • ■ 充电电压:DC5V/1A
  • ■ 接口类型:Type-C
  • ■ 充电指示:红灯亮–充电中 / 绿灯亮–已满电

注意事项

  1. 1、首次使用前请先将电量充满,否则可能因电路开启了保护而无法亮灯。(充电后保护自动解除)
  2. 2、请勿使用输出电压大于5V/1A的充电设备为灯充电。
  3. 3、请使用带有安全认证的手机充电适配器为灯充电。
  4. 4、充电时禁止使用。
  5. 5、请远离火源;勿在潮湿、高温的环境下使用;勿让儿童使用或接触本产品;勿自行维修或更换任何零部件。

若说明书中的内容无法为您解决问题,请及时联系商家,感谢您的支持与信任。

Manual

QC PASSED

Please fully charge the battery before using it for the first time.

Description of Modes and Their Functions

Constant On Mode ■ The light stays on continuously, the sensing function does not work, and it does not turn off automatically.
Night Sensing Mode ■ The light will automatically light up when both sensing human and in low lit environment, otherwise it won’t automatically light up. ■ The light will automatically turn off when human left the sensing range for after 25 seconds. ■ The light will keep on if human stay in the sensing range.
All day Sensing Mode ■ The light will automatically light up when sensing human. ■ The light will automatically turn off when human left the sensing range for after 25 seconds. ■ The light will keep on if human stay in the sensing range.

Instructions for buttons

■ Initially,the light is turned off. ■ Press 1st time: Constant On Mode. ■ Press 2nd time: Night Sensing Mode. (The night sensing mode will be entered after the light flashes three times) ■ Press 3rd time: All day Sensing Mode. (The all day sensing mode will be entered after the light flashes two times) ■ Press 4th time: Return to the closed state, and repeat this cycle.
■ Press button: Cycle through the light colors. ■ Holding button: Adjusts the brightness.

Sensing range and its precautions

■ The sensing range of the light is 120° from the center point of the probe, within a 3 meter area. However, improper installation or obstructions near the sensing probe may affect the sensing effect.

Installation instructions and precautions

【Installation steps】:

1、Clean and dry the surface of the mounting location.

2、Place the iron sheet on the back of the light finding out the position of the built-in magnet.

3、Remove the adhesive sticker and stick it to the mounting position.

4、Installation is completed. (The light is magnetically attach on the iron sheet and can be taken off at any time.)

Charging instructions

  • ■ Charging voltage:DC5V/1A
  • ■ Charging port:Type-C
  • ■ Charging indication:Red light – charging / Green light – fully charged

Precautions

  1. 1、Please fully charge the battery before using it for the first time.
  2. 2、Do not use a charging devices with an output voltage greater than 5V/1A to charge the lamp.
  3. 3、Please use a safety-certified mobile phone charging adapter to charge the light.
  4. 4、Do not use while charging.
  5. 5、Keep away from fire. Do not use this light in a damp or high-temperature environment. Do not allow children to use or come into contact with this light. Do not attempt to repair or replace any parts by yourself.

If the contents of the manual can not solve the problem for you, please contact the merchant in time, thank you for your support and trust.

매뉴얼

처음 사용하기 전에 배터리를 완전히 충전하세요

모드 및 기능에 대한 설명

상시 켜짐 모드 ■ 표시등이 계속 켜져 있고 감지 기능이 작동하지 않으며 자동으로 꺼지지 않습니다.
야간 감지 모드 ■ 조명은 사람을 감지하거나 조명이 어두운 환경에서는 자동으로 켜지고, 그렇지 않은 경우에는 자동으로 꺼지지 않습니다. ■ 사람이 감지 범위에서 25초 이상 벗어나면 표시등이 자동으로 꺼집니다. ■ 사람이 감지 범위 내에 있으면 불빛이 계속 켜집니다.
하루 종일 센서 모드 ■ 사람을 감지하면 자동으로 불이 켜집니다. ■ 사람이 감지 범위에서 25초 이상 벗어나면 표시등이 자동으로 꺼집니다. ■ 사람이 감지 범위 내에 있으면 불빛이 계속 켜집니다.

버튼에 대한 지침

■ 초기에는 표시등이 꺼져 있습니다. ■ 1번 누릅니다: 상시 켜짐 모드. ■ 2번 누르기: 야간 감지 모드. (조명이 세 번 깜박인 후 야간 감지 모드로 들어갑니다) ■ 3번 누르기: 하루 종일 감지 모드. (표시등이 두 번 깜박이면 하루 종일 감지 모드로 들어갑니다) ■ 4번 누르기: 닫힌 상태로 돌아가서 이 과정을 반복합니다.
■ 버튼 누르기: 밝은 색상을 순환합니다. ■ 보유 버튼: 밝기를 조정합니다.

감지 범위 및 주의 사항

■ 빛의 감지 범위는 프로브 중앙에서 120°, 3m 이내입니다. 그러나 센서 근처에 부적절하게 설치하거나 장애물이 있으면 감지 효과에 영향을 미칩니다.

설치 지침 및 주의 사항

【설치 절차 붙여넣기】:

1、장착 위치의 표면을 깨끗이 닦고 말립니다.

2、내장된 자석의 위치를 찾아 조명 뒷면에 철판을 올려놓으세요.

3、접착 스티커를 제거하고 장착 위치에 붙입니다.

4、설치가 완료되었습니다. (조명은 철판에 자석으로 부착되어 있으며 언제든지 떼어낼 수 있습니다.)

충전 지침

  • ■ 충전 전압 : DC5V/1A
  • ■ 인터페이스 유형 : Type-C
  • ■ 충전 표시 : 빨간색 표시등 켜짐 – 충전 중 / 녹색 표시등 켜짐 – 완전히 충전됨

주의

  1. 1、처음 사용하기 전에 완전히 충전해 주세요. 그렇지 않으면 보호를 위해 회로가 켜져 있어 불이 들어오지 않을 수 있습니다. (충전 후에는 보호 기능이 자동으로 해제됩니다.)
  2. 2、출력 전압이 5V/1A를 초과하는 충전 장치를 사용하여 램프를 충전하지 마세요.
  3. 3、램프를 충전할 때는 안전 인증을 받은 휴대폰 충전 어댑터를 사용하세요.
  4. 4、충전 중에는 금지됩니다.
  5. 5、점화원에서 멀리 떨어뜨려 놓으세요; 습하고 고온의 환경에서 사용하지 마세요; 어린이가 이 제품을 사용하거나 접촉하지 않도록 하세요; 혼자서 부품을 수리하거나 교체하지 마세요.

매뉴얼의 내용으로 문제를 해결할 수 없는 경우 판매자에게 제때 연락해 주시고, 여러분의 지원과 신뢰에 감사드립니다.

説明書です

初めて使用する前に、バッテリーを十分に充電してください。

モデルとその機能の説明

常時点灯モード ■ ライトが点灯し続け、感知機能が働かず、自動的に消灯しない。
ナイトセンスモード ■ 光量不足で人を検知した場合のみ自動点灯。 ■ 人が感知エリアから離れると、約25秒後に自動的に消灯する。 ■ 検知エリア内を移動した場合、連続点灯。
終日センサーモード ■ 十分な明るさがあってもなくても、人を感知すると自動的にライトが点灯する。 ■ 人が感知エリアから離れると、約25秒後に自動的に消灯する。 ■ 検知エリア内で人が動いていた場合、ライトは点灯し続ける。

ボタンの説明

■ 当初はオフ。 ■ 1回目を押す: 常時オンモード。 ■ 2回目: 夜間感知モード。(ライトが3回点滅した後、夜間感知モードに入る) ■ 3回目を押す: 終日感知モード。(ライトが2回点滅した後、終日感知モードになります) ■ 4回目: 閉じた状態に戻り、このサイクルを繰り返す。
■ ボタンを押す: 光の色を切り替えます。 ■ ホールドボタン: 明るさを調整します。

感知範囲と注意事項

■ ライトの感知範囲は、プローブの中心から120°、3m以内です。 ただし、不適切な設置やセンシングプローブ付近に障害物があると、センシング効果に影響を及ぼす可能性がある。

設置方法と注意事項

【貼り付け手順】:

1、取り付け場所の表面を清掃し、乾燥させる。

2、鉄板をライトの背面に置き、内蔵磁石の位置を確認する。

3、粘着シールをはがし、取り付け位置に貼り付ける。

4、取り付け完了。(ランプはマグネットで鉄板に取り付けられており、いつでも取り外すことができる。)

充電方法

  • ■ 充電電圧 : DC5V/1A
  • ■ インターフェース・タイプ : Type-C
  • ■ 充電表示 : 赤ランプ 点灯 – 充電中 / 緑点灯 – フル充電

注意事項

  1. 1、最初の時間の最初の使用の前に、最初のフルパワーにしてください、そうでなければ回路が原因で保護が開かれ、点灯することができない場合があります。(保護は充電後に自動的に解除されます)
  2. 2、ランプの充電には、出力電圧が5V/1Aを超える充電機器は使用しないでください。
  3. 3、ランプの充電には、安全認証のある携帯電話充電アダプターを使用してください。
  4. 4、充電中の使用禁止。
  5. 5、発火源に近づけないでください。湿気の多い、高温の環境では使用しないでください。子供にこの製品を使用させたり、接触させないでください。

マニュアルの内容で解決できない場合は、販売店にご連絡ください。

Manuel de l’utilisateur

Veuillez charger complètement la batterie avant de l’utiliser pour la première fois.

Description des modes et de leurs fonctions

■ La lumière reste allumée en permanence, la fonction de détection ne fonctionne pas et la lumière ne s’éteint pas automatiquement.
■ La lumière s’allume automatiquement lorsqu’elle détecte un être humain et dans un environnement faiblement éclairé, sinon elle ne s’allume pas automatiquement. ■ La lumière s’éteint automatiquement environ 25 secondes après qu’une personne a quitté la zone de détection. ■ Le voyant restera allumé si l’homme reste dans la zone de détection.
■ La lumière s’allume automatiquement lorsqu’elle détecte un être humain. ■ La lumière s’éteint automatiquement environ 25 secondes après qu’une personne a quitté la zone de détection. ■ Le voyant restera allumé si l’homme reste dans la zone de détection.

Instructions pour les boutons

  • ■ Initially,the light is turned off.
  • ■ Appuyer une première fois : Mode marche constante.
  • ■ Appuyer une deuxième fois : Mode de détection nocturne . (Le mode de détection nocturne est activé lorsque la lumière clignote trois fois)
  • ■ Appuyer une troisième fois : Mode de détection pour toute la journée. (Le mode de détection pour toute la journée sera activé après que la lumière ait clignoté deux fois)
  • ■ Appuyer une quatrième fois : Revenir à l’état fermé et répéter ce cycle.
  • ■ Appuyer sur le bouton : Pour visualiser la couleur de la lumière.
  • ■ Bouton de maintien : Réglage de la luminosité.

Plage de détection et ses précautions

■ La portée de la lumière est de 120° à partir du point central de la sonde, dans une zone de 3 mètres. Toutefois, une installation incorrecte ou des obstructions à proximité de la sonde de détection peuvent affecter l’effet de détection.

Instructions et précautions d’installation

【Étapes de l’installation】:

de l’emplacement de montage.

2. Placez la feuille de fer à l’arrière de la lampe pour déterminer la position de l’aimant intégré.

3. Retirer l’autocollant et le coller sur la position de montage.

4. L’installation est terminée. (La lumière est fixée magnétiquement sur la feuille de fer et peut être enlevée à tout moment.)

Instructions de chargement

  • ■ Tension de charge: DC5V/1A
  • ■ Port de charge: Type-C
  • ■ Indication de charge: Voyant rouge allumé – charge / Voyant vert allumé – charge complète

Précautions:

  1. 1. Veuillez charger complètement la batterie avant de l’utiliser pour la première fois.
  2. 2. N’utilisez pas de chargeurs dont la tension de sortie est supérieure à 5V/1A pour charger la lampe.
  3. 3. Veuillez utiliser un adaptateur de charge pour téléphone portable certifié pour recharger la lampe !
  4. 4. Ne pas utiliser pendant la charge.
  5. 5. Tenir à l’écart du feu. N’utilisez pas cette lampe dans un environnement humide ou à haute température. Ne pas laisser les enfants utiliser ou entrer en contact avec cette lampe. N’essayez pas de réparer ou de remplacer des pièces par vous-même.

Si le contenu du manuel ne permet pas de résoudre le problème, veuillez contacter le commerçant en temps voulu.

Istruzioni

Caricare completamente la batteria prima di utilizzarla per la prima volta.

Descrizione delle modalità e delle loro funzioni

■ La luce rimane accesa continuamente, la funzione di rilevamento non funziona e non si spegne automaticamente.
■ La luz se encenderá automáticamente cuando detecte personas y en un entorno con poca luz, de lo contrario no se encenderá automáticamente. ■ La luce si spegne automaticamente circa 25 secondi dopo che una persona ha lasciato l’area di rilevamento. ■ La luce rimarrà accesa se l’uomo rimane nel campo di rilevamento.
■ La luce si accende automaticamente quando rileva la presenza umana. ■ La luce si spegne automaticamente circa 25 secondi dopo che una persona ha lasciato l’area di rilevamento. ■ La luce rimarrà accesa se l’uomo rimane nel campo di rilevamento.

Istruzioni per i pulsanti

  • ■ Inizialmente, la luce è spenta.
  • ■ Premere la prima volta: Modalità di accensione costante.
  • ■ Premere la seconda volta: Modalità di rilevamento notturno. (La modalità di rilevamento notturno viene attivata dopo che la luce lampeggia tre volte)
  • ■ Premere la terza volta: Modalità di rilevamento per tutto il giorno. (La modalità di rilevamento per tutto il giorno viene attivata dopo che la luce lampeggia due volte)
  • ■ Premere la quarta volta: Tornare allo stato chiuso e ripetere questo ciclo.
  • ■ Premere il pulsante: Il colore della luce si alterna.
  • ■ Pressione prolungata: Regola la luminosità.

Campo di rilevamento e precauzioni

■ Il campo di rilevamento della luce è di 120° dal punto centrale della sonda, entro un’area di 3 metri. Tuttavia, un’installazione impropria o la presenza di ostacoli in prossimità della sonda di rilevamento possono compromettere l’effetto di rilevamento.

Istruzioni e precauzioni per l’installazione

【Fasi di installazione】:

1. Pulire e asciugare la superficie della posizione di montaggio.

2. Posizionare la lastra di ferro sul retro della lampada scoprendo la posizione del magnete incorporato.

3. Rimuovere l’adesivo e incollarlo sulla posizione di montaggio.

4. L’installazione è completa. (La luce è fissata magneticamente allo lastra di ferro e può essere tolta in qualsiasi momento.)

Istruzioni per la ricarica

  • ■ Tensión de carga: DC5V/1A
  • ■ Porta di ricarica: Type-C
  • ■ Indicazione di carica: Luce rossa – in carica / Luce verde accesa – carica completa

Precauzioni

  1. 1. Caricare completamente la batteria prima di utilizzarla per la prima volta.
  2. 2. Non utilizzare dispositivo di ricarica con tensione di uscita superiore a 5V/1A per caricare la lampada.
  3. 3. Per caricare la luce, utilizzare un adattatore di ricarica per telefoni cellulari certificato per la sicurezza!
  4. 4. Non utilizzare durante la carica.
  5. 5. Tenere lontano dal fuoco. Non utilizzare questa lampada in ambienti umidi o ad alta temperatura. Non permettere ai bambini di usare o entrare in contatto con questa lampada. Non tentare di riparare o sostituire le parti da soli.

Se il contenuto del manuale non può risolvere il problema per voi, si prega di contattare il commerciante in tempo, grazie per il vostro sostegno e la fiducia.

Handbuch

Bitte laden Sie den Akku vollst ndig auf, bevor Sie ihn zum ersten Mal benutzen.

Beschreibung der Modi und ihrer Funktionen

Konstant Ein Modus
  • ■ Das Licht leuchtet ununterbrochen, die Erkennungsfunktion funktioniert nicht, und es schaltet sich nicht automatisch aus.
Nachtsensorik-Modus
  • ■ Das Licht leuchtet automatisch auf, wenn es einen Menschen erkennt und in einer schwach beleuchteten Umgebung, ansonsten leuchtet es nicht automatisch auf.
  • ■ Das Licht erlischt automatisch etwa 25 Sekunden, nachdem eine Person den Erfassungsbereich verlassen hat.
  • ■ Das Licht leuchtet weiter, wenn der Mensch im Erfassungsbereich bleibt.
Ganztägiger Erfassungsmodus
  • ■ Das Licht leuchtet automatisch auf, wenn ein Mensch erkannt wird.
  • ■ Das Licht erlischt automatisch etwa 25 Sekunden, nachdem eine Person den Erfassungsbereich verlassen hat.
  • ■ Das Licht leuchtet weiter, wenn der Mensch im Erfassungsbereich bleibt.

Anweisungen für Tasten

  • ■ Zu Beginn ist das Licht ausgeschaltet.
  • ■ Mal drücken: Konstant-Ein-Modus.
  • ■ Mal drücken: Nachtsensormodus. (Der Nachtsensormodus wird aktiviert, wenn das Licht dreimal blinkt)
  • ■ Mal drücken: Ganztägiger Sensormodus. (Der ganztägige Sensormodus wird nach zweimaligem Blinken des Lichts aktiviert)
  • ■ Mal drücken: Rückkehr in den geschlossenen Zustand und Wiederholung dieses Zyklus.
  • ■ Taste drücken: Wechsell durch die Lichtfarben.
  • ■ Halten-Taste: Stellt die Helligkeit ein.

Erfassungsbereich und seine Vorkehrungen

■ Der Erfassungsbereich des Lichts beträgt 120° vom Mittelpunkt der Sonde aus, innerhalb eines Bereichs von 3 Metern. Eine unsachgemäße Installation oder Hindernisse in der Nähe des Messfühlers können jedoch die Messwirkung beeinträchtigen.

Installationsanweisungen und Vorsichtsmaßnahmen

【Installationsschritte】:

1. Reinigen und trocknen Sie die Oberfläche des Montageortes.

2. Legen Sie das Eisenblech auf die Rückseite der Leuchte, um die Position des eingebauten Magneten zu ermitteln.

3. Entfernen Sie den Aufkleber und kleben Sie ihn auf die Montageposition.

4. Die Installation ist abgeschlossen. (Die Leuchte ist magnetisch an der Eisenplatte befestigt und kann jederzeit abgenommen werden.)

Anweisungen zum Aufladen

  • ■ Ladespannung: DC5V/1A
  • ■ Anschluss zum Aufladen: Type-C
  • ■ Anzeige des Ladevorgangs: Rotes Licht leuchtet – Laden / Grünes Licht leuchtet – voll aufgeladen

Vorsichtsmaßnahmen

  1. 1. Bitte laden Sie den Akku vollständig auf, bevor Sie ihn zum ersten Mal benutzen.
  2. 2. Bitte verwenden Sie keine Ladegeräte mit einer Ausgangsspannung von mehr als 5V/1A zum Aufladen der Lampe.
  3. 3. Bitte verwenden Sie zum Aufladen der Leuchte einen sicherheitszertifizierten Handy-Ladeadapter!
  4. 4. Nicht während des Ladens verwenden.
  5. 5. Aus Sicherheitsgründe. Verwenden Sie diese Leuchte nicht in einer feuchten Umgebung oder bei hohen Temperaturen. Kinder dürfen diese Leuchte nicht benutzen oder mit ihr in Berührung kommen. Versuchen Sie nicht, irgendwelche Teile selbst zu reparieren oder auszutauschen.

Wenn der Inhalt des Handbuchs kann nicht das Problem für Sie zu l sen, wenden Sie sich bitte an den H ndler in der Zeit, ich danke Ihnen für Ihre Unterstützung und Vertra

Instrucciones

Cargue completamente la batería antes de utilizarla por primera vez.

Descripción de los modos y sus funciones

Modo encendido constante
  • ■ La luz permanece encendida continuamente, la función de detección no funciona y no se apaga automáticamente.
Modo de detección nocturna
  • ■ La luz se encenderá automáticamente cuando detecte personas y en un entorno con poca luz, de lo contrario no se encenderá automáticamente.
  • ■ La luz se apaga automáticamente unos 25 segundos después de que una persona abandone la zona de detección.
  • ■ La luz se mantendrá encendida si el ser humano permanece en el rango de detección.
Modo de detección durante todo el día
  • ■ La luz se encenderá automáticamente al detectar humanos.
  • ■ La luz se apaga automáticamente unos 25 segundos después de que una persona abandone la zona de detección.
  • ■ La luz se mantendrá encendida si el ser humano permanece en el rango de detección.

Instrucciones para los botones

  • ■ Inicialmente, la luz está apagada.
  • ■ Pulse la 1 vez: Para acceder al modo de luz constante.
  • ■ Pulse la 2 vez: Modo de detección nocturna. (Se entrará en el modo de detección nocturna después de que la luz parpadee tres veces)
  • ■ Pulse la 3 vez: Modo de detección durante todo el día. (El modo de detección durante todo el día se activará después de que la luz parpadee dos veces)
  • ■ Pulse la 4 vez: Vuelva al estado cerrado y repita este ciclo.
  • ■ Pulse el botón: Ciclo a través de los colores de la luz.
  • ■ Botón de retención: Ajusta el brillo.

Alcance de detección y precauciones

■ El alcance de detección de la luz es de 120° desde el centro de la sonda, en un radio de 3 metros. Sin embargo, una instalación incorrecta o una obstrucción cerca de la sonda de detección afectará al efecto de detección.

Instrucciones y precauciones de instalación

【Pasos de instalación】:

1. Limpie y seque la superficie del lugar de montaje.

2. Coloca la lámina de hierro en la parte posterior de la luz averiguando la posición del imán incorporado.

3. Retire el adhesivo y péguelo en la posición de montaje

4. La instalación está completa. (La luz se fija magnéticamente a la chapa de hierro y puede retirarse en cualquier momento.)

Instrucciones de carga

  • ■ Tensión de carga: DC5V/1A
  • ■ Puerto de carga: Type-C
  • ■ Indicación de carga: Luz roja encendida – cargando / Luz verde encendida- carga completa

Precauciones

  1. 1. Cargue completamente la batería antes de utilizarla por primera vez.
  2. 2. No utilice un dispositivo de carga con una tensión de salida superior a 5 V/1 A para cargar la lámpara.
  3. 3. Utilice un adaptador de carga para teléfonos móviles con certificación de seguridad para cargar la luz.
  4. 4. No utilizar durante la carga.
  5. 5. Mantener alejado del fuego. No utilice esta luz en un ambiente húmedo o a altas temperaturas. No permita que los niños utilicen o entren en contacto con esta luz. No intente reparar o sustituir ninguna pieza por su cuenta.

Si el contenido del manual no puede resolver el problema para usted, por favor póngase en contacto con el comerciante en el tiempo, gracias por su apoyo y confianza

故障排查

  • 灯不亮:首次使用前未充满电可能导致电路保护从而无法点亮;按说明先充满电,充电后保护会自动解除。
  • 感应效果不佳:检查是否为不当安装或探头附近存在遮挡物,可能影响感应效果;按说明重新安装并避免探头附近遮挡。
  • 充电异常/无法正常充电:确认使用的充电设备输出不大于 5V/1A,并使用带安全认证的手机充电适配器;充电时禁止使用本灯。
  • 无法解决:若说明书内容仍无法解决问题,请及时联系商家。

Documents / Resources

PDF thumbnailRechargeable Motion Sensor Light
User Manual · COXO, Rechargeable Motion Sensor Light, motion sensor light, night light

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.