RS H-SHIFTER
SETUP GUIDE

RS H-Shifter

ATTACHING THE HANDLE
Attach the shifter handle to the body of the shifter by screwing it into the available hole on top Keep tightening until the handle stops, in order to ensure a solid connection

ATTACHING TO A DESK

To attach the product to your desk you will need to use the included clamp The RS
H-Shifter can be attached to either the front or top of the clamp using the included bolts
- Unscrew the clamp screw until it is open and then continue to unscrew until the cap pops out – doing this will make it much easier to insert and tighten the bolts into the body
- Position the clamp against the body of the shifter and insert and tighten the bolts using the included hex key You can choose to attach the shifter to the front or the top of the clamp, depending on your needs Reinsert the cap of the clamp screw and push in until you feel it click into place
- Position on your desk and adjust the clamp screw until it meets the bottom of the desk – at this point you should tighten the clamp at least one more full rotation, in order to ensure a good secure fit The shifter may shift slightly left or right during use, especially when selecting reverse or 7 gear, but this is expected and should not affect gameplay th

ATTACHING TO A SIMULATION RIG
You can use the included bolts to attach to a plate on some simulation rigs Similar to the desk clamp, attachment to the bottom or the back of the RS H-Shifter body is possible
Depending on the thickness of the plate you are attaching to, washers (not included) may be needed to ensure the bolts don’t encroach too far within the casing of your product Follow this guideline to ensure you do not damage your product
L = T+20mm
Where T = the thickness of the plate that you’re attaching the shifter to and 20mm is the maximum that a bolt can be allowed to encroach inside the product
For example, if you have a 4mm thick plate then the bolt can not be any more than 24mm in length (4mm + 20mm = 24mm) If using longer bolts, washers of appropriate size will need to be used in order to reduce how far the bolt encroaches inside the product
Note: if you also own the RS Shifter and Handbrake and wish to attach both to your rig, the desk clamp can also be used to accommodate different configurations, such as having the handbrake above the shifter Just bolt through the plate into the device attached to the top of the desk clamp and then attach the other device to the front of the clamp You may need to obtain longer M6 bolts in order to facilitate this, but always remember the above formula with regards to encroachment inside the shifter

SELECTING GEAR POSITIONS
Gear selection method is generally as you will find in most manually geared cars – push the shifter handle into the gear that you wish to select. Most racing titles do require that you have also fully pressed the clutch in order to register that a shift has happened. If you find that you select a gear and this is not recognised by the game, with the car remaining in neutral, make sure that you are fully pressing the clutch.
Access to the 7th and Reverse gears is behind a push-through lockout system. This is designed to prevent accidental mis-shifting into 7th gear when changing from 4th to 5th gear. The push-through lockout functions similarly to actual cars that also use this lockout method for the manual shifter. Move the shifter handle to the position where you can feel resistance and then increase pressure until the handle pushes through the resistance.
SETTING UP RS H-SHIFTER IN GAMES TITLES
For the vast majority of racing titles, the RS H-Shifter is compatible by default when connected to a compatible Logitech steering wheel This table summarises the options:

When connected directly to the PC the RS H-Shifter acts as its own device and will need to be set up in game titles by assigning the functions using the options screens of the title you are using
When connected to a wheel with a USB A port on it (such as the RS50 or Pro Racing Wheel) then some setup may still be required, depending on the game Either way, when it’s connected to the wheel it acts as if it is part of the wheel:
- Some titles will require you to change the shifting method to manual with clutch, for example
- Some titles may still require that you manually assign the gear positions to the relevant functions within the control options of the game
When connecting to wheels such as G29, G920 or G923, the use of the Logitech G Racing
Adapter is required in order to adapt the USB port used on the RS H-Shifter to the analog 9 pin port used for the shift function of those wheels As these wheels were not designed to support a 7 gear though, you will not be able to utilise that option Gears 1 to 6 and reverse will still function correctly though th A list of supported titles can be found at logitechG com/support/RS-HS
ASSIGNING CONTROLS IN GAMES TITLES
Every game title can differ slightly in the exact method of assigning controls but the same basic paradigm applies:
- Find the control options screen of the game title
- Navigate to the function that you wish to reassign
- Tell the game title that you want to reassign the control The method for this will differ between games and platforms – it could be by:
a Pressing the selection button (usually the Cross or A button) on the wheel
b Clicking or double clicking with the mouse (PC only)
c Press return on the keyboard (PC only) - At this point the game title will wait for you to press/move the part of the controller that you want to assign – do so and the game title should register this movement and display the reassignment
Further details of this can be found by watching the support videos on the Logitech support site at this link: logitechG com/support/RS-HS
AVAILABLE SETTINGS WHEN USING G HUB
Assignments

It is possible to assign keystroke and macros to each of the gear positions The method for doing this is in line with any other device supported in G HUB
Recalibration

If during the RS H-Shifter’s lifetime you find that selecting certain gears does not work, then the device may need recalibrating Within the RS H-Shifter’s settings in G HUB there is a calibration option that allows you to redefine each of the gear shift positions Simply click the option and follow the onscreen instructions to perform this function
ATTACHING ALTERNATIVE SHIFTER KNOBS OR SHAFT EXTENDERS
The shifter knob of RS H-Shifter is removable – simply unscrew it from the handle You can then attach aftermarket knobs available from any automotive supplier The thread on the handle is M8x1 25 Alternatively, many aftermarket options utilize a clamp-style setup to attach to the handle, which also works

If you find that the whole handle unscrews, including the shifter knob, then you will need to use a 7mm or 9/32 inch wrench/spanner to apply leverage in order to unscrew the shifter knob Use the flat sides of the bottom of the handle for this.

REMOVING THE COLLAR ON THE HANDLE
After some time the collar on the handle may become worn Replacements are available on the website
Follow these steps to replace the collar:
- Remove the shifter knob

- Use a 7mm or 9/32 inch (or adjustable) wrench/spanner to unscrew the handle from the body of the shifter Two opposingsides of the thread are flat and can be used with a wrench/ spanner to loosen the handle:
Once you have loosened the handle with the wrench/ spanner, you should be able to use your fingers to finish unscrewing the handle - There are two rubber o-rings that will need to be removed Use a pair of tweezers to remove the first rubber o-ring
Then do the same with the second one that holds the collar in place:
- Once those are removed, the collar will slide off

- Replace with the new collar, place the o-rings back in their original positions and then attach the handle back tothe shifter

©2026 Logitech. Logitech, Logitech G, Logi and their respective logos are trademarks or registered trademarks of Logitech Europe S.A. and/or its affiliates in the U.S. and other countries. All other trademarks are the property of their respective owners. Logitech assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change
without notice.
WEB-621-002733 002
Documents / Resources
![]() | RS H-Shifter |
References
- User Manualmanual.tools
