XTOOL P720 Smart Diagnostic System User Manual

XTOOL LogoUser Manual
P720 Smart Diagnostic System

Please read this user manual carefully before using the P711 Smart Diagnostic System, referred to as the “Scan Tool” throughout this document. When reading the manual, please pay attention to the words “Note” or “Caution”, and read them carefully for appropriate operation.

OPERATION INSTRUCTIONS

For safe operation, please follow the instructions below:

  • Keep the device away from heat or fumes when in use.
  • If the vehicle battery contains acid, please keep your hands and skin or fire sources away from the battery during testing.
  • The exhaust gas of the vehicle contains harmful chemicals. Please ensure adequate ventilation.
  • Do not touch the vehicle cooling system components or exhaust manifolds when the engine is running due to the high temperatures reached.
  • Make sure the car is securely parked, Neutral is selected or the selector is at the P or N position to prevent the vehicle from moving when the engine starts.
  • Make sure the (DLC) Diagnostic Link Connector is functioning properly before starting the test to avoid damage to the Diagnostic Computer.
  • Do not switch off the power or unplug the connectors during testing. Doing so may damage the ECU (Electronic Control Unit) and/or the Diagnostic Computer.

CAUTIONS!

  • Avoid shaking, dropping or dismantling the scan tool as it may damage the internal components.
  • Use only your fingertips to touch the LCD screen. Hard or sharp objects may damage the scan tool.
  • Do not use excessive force;
  • Do not expose the screen to strong sunlight for a long period.
  • Please keep the scan tool away from water and moisture.
  • Store and use the scan tool only within the temperature ranges identified in the Technical Specifications section.
  • Keep the unit away from strong magnetic fields.

AFTERSALES-SERVICES

XTOOL strives to provide best-in-class support!
E-Mail: support1@xtooltech.com (for Amazon)
support2@xtooltech.com (for Ali-Express, eBay and others)
Tel: +86 755 21670995 or +86 755 86267858 (China)
Official Website: www.xtooltech.com
www2.xtooltech.com (Alternate sites)

GENERAL INTRODUCTION

The XTOOL P711 smart diagnostic system (referred to as the “Scan Tool”) is an advanced scanning tool based on the Android operating system. It supports multiple languages and is suitable for different countries and regions. The advantage of this OBD-II (On-Board Diagnostics version 2) scanner is its comprehensive functions and its ability to quickly provide the user with more accurate diagnostic information.
TABLET

XTOOL P720 Smart Diagnostic System

  1. USB Port
  2. VAG Port
  3. Power Button
  4. 7-inch LCD
  5. Rear Camera
  6. Nameplate
  7. Holder
  8. Speaker

VEHICLE CONNECTION

The scan tool must be connected to the vehicle’s OBD-II port so that the tablet can establish correct vehicle communication. Please perform the following steps:

  1. Turn on the tablet
  2. Connect vehicle and tablet via the main test cable
  3. Switch on the ignition and tap on the Diagnostic application to start your diagnosis.
    The connection method is shown in the figure below:

XTOOL P720 Smart Diagnostic System - CONNECTION

  1. Vehicle
  2. DB15 to OBD2-16 Main Cable
  3. Tablet

HORECAROMA La Doppia Espresso Coffee Machine - Symbol 1 Note: Please make sure all the cables are connected tightly; The vehicle’s DLC is not always located under the dash; for the location of the DLC, please refer to the vehicle’s user manual.

Precautions for Diagnosis

  1. The voltage range on the car: +9~+18V DC;
  2. When testing some special functions, the operator must operate according to the prompts and meet the test conditions. For some models [special functions], the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
  3. The electronic control systems of different models are very complicated. If you encounter situations where it is impossible to test or a large amount of test data is abnormal, you can search for the ECU of the vehicle and select the menu for the model on the ECU nameplate;
  4. If the vehicle type or electronic control system to be tested is not found in the diagnostic function, please upgrade the vehicle diagnostic software to the latest version using the Updates menu or consult the XTOOL technical service department;
  5. Only wiring harnesses provided by XTOOL and designed for the scan tool are permitted to be used with this scan tool to avoid damage to the vehicle or the scan tool;
  6. When running a Diagnostics function, it is forbidden to shut down the scan tool directly. You should cancel the task before returning to the main interface and then shutting down the scan tool.

COMPLIANCE INFORMATION

FCC COMPLIANCE
FCC ID: 2AW3IP01V71
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference 2) This device must accept any interference received, including interference that may cause undesired operation.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC  Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information
This device meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluations of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: This device has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the device kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain an 0mm separation distance between the user’s body and the back of the device. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
Responsible Party
Company Name: FCC US Agent, LLC
Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA
Email: Support@FCCUSAgent.com
ISED STATEMENT
IC: 29441-P01V71
PMN: P720, P01V71, D7S, XT70, X100PADS, Scantech Pro, AutoProPAD Core HVIN: P01V71B
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES (B) / NMB (B).
This device meets the exemption from the routine evaluation limits in section 6.6 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
The device for operation in the band 5150–5350 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems.
Specific Absorption Rate (SAR) information:
This device meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. ISED RF Exposure Information and Statement the SAR limit of Canada(ISED) is 1.6 W/kg averaged over one gram of tissue. Device types: Device has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the device kept 0mm from the body. To maintain compliance with ISED RF exposure requirements, use accessories that maintain an 0mm separation distance between the user’s body and the back of the device. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with ISED RF exposure requirements, and should be avoided.
Responsible Party
Company name: Canadian certification consulting, Inc.
Address: 2210 Horizon Drive, Suite 17West Kelowna, BC V1Z 3L4, Canada
E-mail: info@can-cert.com
CE
Declaration of conformity
Hereby, Shenzhen XTOOLtech Intelligent Co., Ltd declares that this Smart Diagnostic System is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.
UKCA
Hereby, Shenzhen XTOOLtech Intelligent Co., Ltd declares that this Smart Diagnostic System satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body.

Shenzhen Xtooltech Intelligent Co., LTD

Documents / Resources

PDF thumbnailP720 Smart Diagnostic System
User Manual · P01V71, 2AW3IP01V71, D7S, XT70, X100PADS, AutoProPAD Core, P720, HVIN P01V71B, OBD-II scanner, car diagnostic tool, P720 Smart Diagnostic System, Smart Diagnostic System, Diagnostic System

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.