Skydroid H12 Remote Controller User Manual

Skydroid-logo

Skydroid H12 Remote Controller

Skydroid-H12-Remote-Controller-product-removebg-preview

Attention
This product uses the following terms to classify the potential hazards that may be caused by improper operation.

  • Note: If not follow the instructions, it may cause property damage and minor injuries.
  • Note: If not follow the instructions, it may cause property damage, major accidents and serious injuries.
  • Warning: Misuse of this product may result in injury, damage or loss of property. Read the manual carefully before using this product. This item is not a toy. This item is intended for use by professional UAV operators and installers only. Do not use this product if you lack the knowledge and expertise to install and maintain UAV radio equipment. Do not use unapproved or unofficial components with this system. Operators must strictly follow the operation guides set forth in this manual. Skydroid does not accept any liability for the use or misuse of this product.

Overview

  1. Product Features
    1. The H12 series uses newest Qualcomm Snapdragon 625 processor, equipped with an Android embedded system and advanced SDR technology and super protocol stack, making the image clearer, lower the latency, longer distance, stronger anti-infection, whether it is drones, robots, industrial control equipment, etc. can be applied.
    2. We provide development kits, SDKs and technical support for digital cameras, serial transparent transmission, sbus and other rich interfaces. Equipped with coach PPM output, Type-C Android high speed USB interface, expanded TF card slot, etc.
    3.  The 1920 * 1080 resolution high brightness display screen, with a large proportion of screens, can still clearly view the real-time display information in a sunny environment.
    4.  The dual-antenna signals complement each other, with super-strong signals and
      ultra-long transmitting distances, combined with algorithm control and out-of-step frequency hopping algorithms, greatly increasing the ability to communicate with weak signals.
    5.  Skydroid Fly App has undergone a lot of optimization based on QGC, a better interactive interface, a larger controllable map field of viewing, the aircraft implements intelligent waypoint planning, automatic execution, automatic follow-up, and one-click home, highly provides working effectiveness in professional fields.
  2. Main applications
    1. It is used to remotely operate helicopters, fixed wings, multi-rotors, vehicles, ships, etc. for video/image transmission (camera optional), data transmission, telemetry, and control drone flight.

Remote Controller Specification

Remote Controller Specification
Model No.Working voltage H124.2V ChannelsRF Power 12
20DBm@CE/23DBm@FCC
Frequency 2.400-2.483GHz Frequency hopping Newest FHSS
Update waySize APP Update online190*152*94min WeightBattery 646g10000mA/H
Endurance 6-20Hrs Charging port TYPE-C
Applications
Helicopter, fixed wing, multi-rotor, unmanned vehicle, unmanned boat, etc.to ground: 2 – 5km to air: 5 – 10km
Range(Open & no interference)

Receiver Specification

Receiver Specification
Model No.Working Voltage R124.5-5.5V ChannelsWorking current 12140mA@5V
Size 51*41*13mm Weight 14g

Components

The composition of the model and its significance

Skydroid-H12-Remote-Controller- (2)

Number Annotation Number Annotation
1 2.4G 3dB antenna 10 Button B
2 Toggle 3 positions switcher E 11 Stick X2、Y2
3 Thumbwheel switch G 12 Button D
4 Button C 13 Thumbwheel switch H
5 Stick X1、Y1 14 Toggle 3 positions switcher F
6 5.5inch screen 15 Speaker
7 MIC port 16 SIM card slot
8 Button A 17 Charging port
9 Power switcher 18 PPM output

Remarks: 6 Touch screen, you can click the screen to operate. Please pay attention to waterproof the screen when using it (such as avoiding rain water falling on the screen in rainy days), so as to avoid damage to the screen caused by water ingress.

Receiver

Skydroid-H12-Remote-Controller- (3)

Name Annotation Name Annotation
RED LED Red light 2.4 ANT Antenna
GN LED Green light GND Camera ports
MODE KEY Button VCC
GND Ground RX1
USB 5V USB for upgrading TX1
DM/CH9 GND transmiDssaitoan/CBUS
DP/CH10 5V
GND RX2
RX3 Expansion ports TX2
TX3 GND SBUSAntenna
SBUS
2.4G ANT

Receiver Status light 

Receiver LED status Indication Receiver Status
Solid Green LED Connection Normal Disconnected
Flash slowly Green LED Binding mode
Flash rapidly Green LED C. Bus mode
Solid Red LED Upgrading
Flash slowly Red LED Self test failed, Re-try or return to factory
Flash rapidly Red LED

Remote control antenna angle

  1.  Adjust the angle of the remote control antenna to face the flight direction of the drone.
  2. Antennas shall not form shielding or crossing with each other.

Right operation

Skydroid-H12-Remote-Controller- (4)

Keep the antenna extended and 45 ° upwards

Wrong operation Skydroid-H12-Remote-Controller- (5)

  • Antenna cannot cross on each other
  • The antenna cannot be parallel to the remote control

Environment conditions

Pay attention

  • Working temperature:-10°C~+55°C。
  • Relative humidity:Not exceed 85%。
  • Atmospheric pressure:86kPa~106kPao
  • Working environment should not contain explosive material or any corrosive or harmful gas may cause interference in the operation of the product.
  • Always work under shelter to prevent rain, snow, wind, sand and dust contamination.
  • This remote controller and receiver are not waterproof.

Working conditions

Power supply and attentions

  • H12 series uses a built in Li-ion battery. Charging port is compatible with 9V -2A Type-C chargers (such as cell phone, digital cameras’ USB charger).
  • In case of smoke, heat or unusual smell during charging, please stop charging immediately and return to our company for servicing as soon as possible.
  • Do not leave the product unattended while charging. Do not leave the product in a place where children can reach. Do not charge when room temperature over 60 ℃.

Safety

  • DO NOT fly under the influence of substances, or when tired!
  • DO NOT fly in strong wind and or rainy conditions!
  • DO NOT fly close to electric emission towers, communication stations and crowded area! DO NOT fly nearby airports and other prohibited areas!
  • DO NOT fly around people or animals, or in any location where possible to damage property!
  • Check equipment before every flight and check whether the transceiver system and the drones are normal or not.
  • Please use certified chargers to charge the batteries.
  • DO NOT put unnecessary force on antennas since its weakness.

Operation

  1. Preparation and pre-checking before use
    Pay attention
    1.  Check battery level.
    2.  Check position of the antenna to get the best performance.
    3. Make sure the firmware is the latest version.
    4.  DO NOT operate under the influence of alcohol or drugs.
  2. OperationSkydroid-H12-Remote-Controller- (6)

Enter setting, and then enter system, choose your language.

Status bar Skydroid-H12-Remote-Controller- (7)

  1. Bluetooth
  2. Signal
  3. SIM card status (without sim card in the picture)
  4. Power lever (charging in the picture)
  5. Time
  6. Back ground management
  7. Home
  8. Return to last step

H12 HelperSkydroid-H12-Remote-Controller- (8)

  1. Mode change
  2. Rudder value
  3. Binding the remote control with other receivers (the binding method is introduced in below)
  4.  Video/image transmission checking
  5.  In the advanced parameters setting, you can adjust the channel, upgrade the joystick firmware, and modify the receiver’s serial port baud rate (password requested from our engineers)

Binding operation

Receiver Skydroid-H12-Remote-Controller- (9)

  1. When the receiver is powered on, the green light flashes quickly after short connecting GND and MODE KEY. Open the H12 Helper on the remote control, click “binding” to start binding. The green light of the receiver is always on after the binding successfully.
  2.  Quickly power on and off the receiver 5 times, and start the binding mode at the 6th time, on when, the green light flashing. Open the H12 Helper on the remote control, click “binding” to start binding. The green light of the receiver is always on after the binding successfully.

Use serial port cable (need be purchased separately) to share data transmissionSkydroid-H12-Remote-Controller- (10)

Take H12 connecting Mission Planner as an example

  1.  One end is plugged into the H12 remote control audio port, and the other end is connected to the computer. If it is the first time you use it, please firmly/tightly plug it in to ensure its stable connection. Skydroid-H12-Remote-Controller- (11)
  2. Open the Mission Planner ground station, select the corresponding COM port, and connect with the baud rate of 115200.
    The Mission Planner is only suitable for Pix and APM flight control, and other flight controls need to be connected with the computer ground station adapted.

Skydroid-H12-Remote-Controller- (1)

Maintenance

  • Storage for not using for a long period
  • Put H12 in a dry and ventilated area. No direct sun light to prevent harm to the internal li-ion battery.
  • If store it over 3 months, it is highly recommended to put it in a room temperature between 22℃ to 28 ℃. DO NOT put it – 20 ℃ or higher than 45℃.

Transportation and storage

Warning
In order to prevent lost or getting hurt, please strictly follow the rules of operation as below: Keep small parts or wire far away from children. DO NOT let children touch the small/spare parts of H12.

Attention

  1. DO NOT put H12 into water. If it does, please switch off the power and dry it at once!
  2. DO NOT crash the H12 or break and DO NOT drop the battery.

Documents / Resources

PDF thumbnailH12 Remote Controller
User Manual · Skydroid, H12, R12, V1.0, remote controller, UAV controller

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.