Avantree Orbit Pro Interactive Setup

Specifications
| Item | Details (from manual) |
|---|---|
| Guide version | Version 1.3 |
| Power/Mode switch | TX (transmitter mode), RX (receiver mode), OFF/TX (bypass audio to speakers) |
| Input switch modes | OPT (TV Optical OUT), AUX (TV 3.5mm AUX or RCA output), HDMI (TV HDMI ARC) |
| Pairing scan | Press button once to search; “Searching” shown on bottom of LCD screen |
| Discovery timing | Wait 5–10 seconds once found |
| Volume controls | Press once to adjust volume; also supports remote volume adjustment |
| Clear pairing history | Press & hold both buttons for 5 seconds |
| Reset transmitter | Press & hold “-” and “+” for 5 seconds; previously connected devices disappear |
| HDMI requirements | Only HDMI ports labeled “HDMI ARC” are valid; use an HDMI 1.4 cable or newer |
| Box contents | Avantree Orbit Pro Transmitter; Remote Control; Type C Power Cable for Transmitter; Optical Audio Cable; AUX 3.5mm Audio Cable |
Quick Setup & Use
- Choose a connection type: set the input switch to OPT, AUX, or HDMI.
- Power the transmitter: switch the power/mode switch to TX, then continue.
- Put the transmitter in pairing/search mode: press the device search button once (shows “Searching” on the LCD).
- Prepare your headphones: enable Bluetooth and put the headphones in pairing mode (pairing steps vary by model).
- Hold headphones close and wait: allow 5–10 seconds until your device name appears.
- Select/connect headphones: press the select button once to connect; confirm the LCD shows Connected with an indicator next to the device name.
- Test audio: play a TV show/movie and verify sound through the headphones.
Warning
You’re about to visit an external link and leave this setup guide
- To come back here again, please use your browser’s “back” button.
Product Overview

Buttons 
What’s in the box?
Connect via Optical
- Plug one end into TV’s “Digital Optical Out”.
- Plug other end into transmitter’s “Optical In”.
- Switch the
button to the “OPT” position 
Connect the transmitter
Plug the USB-C cable into the transmitter and your TV’s USB power port.

Select the right audio settings
- ? Using your TV remote, go to: Settings + Sound- Sound Output
- Select Optical (instead of TV speakers)

Power on the transmitter
Turn ON the transmitter
- Slide power switches to “TX.”

Put the transmitter in pairing mode
- Press the button
once - ” Searching” shown on the bottom of the screen.

Turn Bluetooth off
Turn off Bluetooth on your phone or other devices to disconnect your headphones. 
Put your headphones in pairing mode 
Pairing methods vary by headphones. Most activate by pressing and holding a button for a few seconds.
Hold them close & wait for searching out
- Wait for 5-10 seconds
- Once found, your device’s name appears.

Connect the headphone
- Press
to select device - Press the
button once to connect you select headphone. - Once connected, The
indicator shown to the right of the device name and the “Connected” shown on bottom ofthe LCD screen

Test for sound
Play a TV show or movie and check if you hear the sound through the headphones.
Tip: If your TV’s speakers still play sound, go to Settings → Audio and set “TV Speakers Off”.
Using TV Speakers with Headphones
- The ability to listen through both the TV speakers & headphones depends on your TV model.
- Check your TV’s “Audio Output” settings and look for “TV Speaker + Audio Out” or similar. Or you can use Orbit Pro’s passthorugh function to listen audio through a wired soundbar and bluetooth headphone simultaneously.
Other connection options

Connect via HDMI
- Plug one end of the HDMI cable(not provided) into the TV’s HDMI ARC port
- Plug the other end into the transmitter’s HDMI input.
- Switch the
button to the HDMI” position

- Note 1: Only HDMI ports labeled “HDMI ARC” are valid.
- Note 2: Use an HDMI 1.4 cable or newer.
Connect the transmitter
Plug the USB-C cable into the transmitter and your TV’s USB power port. 
Select the right TV audio settings
- Using your TV remote, go to: Settings> Sound – Sound Output
- Select HDMI ARC

Connect via AUX
- Plug one end of the AUX cable into the
TV’s headphone jack. - Plug the other end into the transmitter’s AUX input.
- Switch the
button to the “AUX” position 
Connect the transmitter
Plug the USB-C cable into the transmitter and your TV’s USB power port. 
Select the right TV audio settings
- Using your TV remote, go to: Settings – Sound – Sound Output
- Select Headphones

Tips 
If they fail to connect, please try: 
Reset the transmitter
- Press & hold “-” & “+” for 5s.
- Once it’s been reset, the previously connected devices displayed on the screen will disappear.
Reset your headphones
Resetting your headphones clears its pairing history.
Different headphones have different resetting processes. Consult your device’s user manual for directions if needed.
Clear your environment
- WiFi routers & devices (e.g., Samsung Smart TVs) may interfere with pairing.
- Unplug or move away to improve connection.

Connect via RCA
Note
- AUX adapter cable NOT included Use RCA ports labeled “AUDIO OUT”
- Contact us for a free RCA to AUX adapter if needed. witch the
button to the “AUX” position
You’re done!
Reach out to us for help!
- You can email us directly at support@avantree.com, to our support page.
- We’ll get back to you within 1 business day!
If you notice a lag in sound
- It may be because your headphones do NOT support low-latency technology.
- For the best latency performance, use headphones that support aptX Low Latency or Fast stream.
- If you’re using a non-aptX device, such as AirPods, you may experience a slight audio delay.
Customer Support
- We hope you enjoy your experience with the Orbit Pro!
- If you ever need anything, please don’t hesitate to reach out to us at support@avantree.com
- Add FREE 24-month coverage!
Troubleshooting
- If they fail to connect: try Reset Transmitter, Reset Headphones, and Clear Environment.
- Reset the transmitter: press and hold – and + for 5 seconds; previously connected devices shown on the screen will disappear.
- Reset your headphones: resetting clears its pairing history (follow your headphones’ user manual for the correct reset process).
- Clear your environment: WiFi routers and some devices (e.g., Samsung Smart TVs) may interfere; unplug or move away to improve connection.
- No sound: if TV speakers still play sound, go to Settings > Audio > TV Speakers Off.
- Experiencing audio lag: the delay may be because your headphones do not support low-latency technology. For best latency, use headphones that support aptX Low Latency or Fast stream. With non-aptX devices (e.g., AirPods), a slight delay may occur.
Documents / Resources
![]() | Orbit Pro Interactive Setup Guide (Version 1.3) |
References
- User Manualmanual.tools

