
Majority Fitzwilliam Connect Amp User Manual

Box Contents
What’s in the Box?
A. Majority Fitzwilliam Connect Amp, featuring an embedded power adaptor
B. Remote Control withtwo x AAA Batteries
C. WLAN Antenna
D. Instructions Manual

Controls & Functions
Fitzwilliam Connect Amp -Front View

- USB playback port
- Navigation / OK / Stop dial
- Mode
- Memory (Save Preset)
- Menu
- Back
- Display screen
- Play/Pause
- Previous / Rewind
- Next / Fast forward
- Info
- Power On/Standby, Volume +/−, Tune +/−
- Remote control sensor
- Headphone jack (3.5 mm)
Fitzwilliam Connect Amp-Back View

17. Power Switch ON/OFF
18. AC mains power adaptor
19. W-LAN/BT Antenna port
20. RCA connection ports for the left and the right speaker (not included)
21. RCA L/R Pre-output ( Line-out)
22. Audio InputL/R (Analog, RCA jack)
23. Digital Input (Optical)
24. DigitalInput (Coaxial)
25. F-type DAB/FM RadioAntenna
Remote Control Operation

Battery Replacement for the Remote Control
- Press down the battery cover at ‘;’ and push the battery cover outwards in the direction of the arrow.
- Insert 2 x AAA 1.5V batteries (not included). Make sure to match the (+) and (-) ends of the battery with the (+) and (-) ends indicated in the battery compartment.
- Close the cover.
Handling the Battery
Improper or incorrect use of batteries may cause corrosion or battery leakage which could cause fire, personal injury or damage to property.
Only use the battery type indicated in this manual.
Do not dispose of the used battery as domestic waste. Dispose of it in accordance with local regulations.
Remove the battery from the remote control when not in use for a long period of time, as corrosion or battery leakage may occur and result in physical injury/property damage/fire.

Remote Control Operation Range
The remote-control sensor on the front unit is sensitive to the remote control’s commands up to a maximum of 4 metresaway and within a maximum of 60°arc.
PLEASE NOTE: The operating distance may vary depending on the brightness of the room.
Product Setup
Please Note: The instructions within this user manual will refer to the button number on the unit e.g. (Ref.Number’), or buttons on the remote control e.g. (Rem. Number’), in accordance with the diagrams from pages 4-6.
The Majority Fitzwilliam Connect Amp tunerfeaturesa Class D high-grade Amplifier (Texas Instruments) with two stereo audio channels, supporting two passive external speakers up to 100W each(not included).
Unpack and Prepare
Remove all packaging and place the tuner on a flat, stable surface near the external speakers you plan to connect.
Connect the Speakers
Use RCA cables to connect the left and right passive speakers( not included) to the corresponding stereo audio channels on the tuner. Insert the RCA cables into the Fitzwilliam speaker connection portsat the back of the unit (Ref.20).
Connect the Antennas
Insert the included DAB/FM radio antennainto its port and extend it fully. Connect the included WLAN antennato the WLAN socket at the back of the unit for Wi-Fi connectivity.
Power On the Unit
Ensure the power switch at the back of the unit is set to ON (Ref.17). Unwind the mains cable completely and plug it into a suitable mains socket. The unit will now power on in standby Mode. Press the Power ON /Standbybuttonto switch to operating Mode.
Important Notes:
- Ensure the power cord is connected to a main socket supplying the correctvoltage.
- Always hold the plug when connecting or disconnecting from the mains —never pull on the cord itself.
- This tuner requires passive speakers to be connectedfor sound output.
Product Setup-Network Connection
Connect to a Network
Ensure a broadband connection is available via a wireless access point, router, or similar network device.
The network device must support Wi-Fi (802.11 a/b/g/n).
Ensure the wireless network is correctly set up and that you have the WEP, WPA, or WPA2 security password available to activate the connection.
Alternatively, use the Wi-Fi Protected Setup (WPS) function for easy pairing between the network device and the tuner.
Check that the indicator lights on the network device show the appropriate status.
First Time Setup
- When powering on the device for the first time, you will be prompted to select a language.
- Rotate the navigation dial to select the desired menu language and press the OK button to confirm.
- After selecting the language, the next screen will display the privacy policy. Press the OKbutton to agree and continue.
- A setup wizard will then appear to assist with configuration. Select ‘YES’and confirm to launch the wizard.
- If ‘NO’is selected, you will be asked whether to start the setup wizard the next time the device is powered on.
Note: The setup wizard helps guide you through system configuration.
Setting Date and Time
- Select either 12-hour or 24-hour format.
- If 12-hour format is selected, AMappears in the morning and PMin the afternoon.
- Choose how the time and date will be updated: Update from DAB, Update from FM, Update from Network, or No update.
- If Update from Networkis selected, you will be prompted to set your time zone on the next screen.
- If No updateis selected, you will need to enter the date and time manually.
- Set Daylight Savingstime to ONfor summer time or OFFfor standard time.
The device will ask next, whether you want to keep the network connected.
- Select YESto keep Wi-Fi enabled and allow control of the device via the app in all operating Modes.
- Select NOto switch Wi-Fi OFFand keep it disconnected. When the tuner is not connected to Wi-Fi, internet radio and podcasts will not function, while other Modes such as Bluetooth, DAB, FM, AUX In, Optical, and Coaxial will still work.
Note: Power consumption in standby Mode will be higher when the network remains connected.
Network Selection
Majority Fitzwilliam Connect Amp will begin scanning for available networks. Any available Wi-Fi networks will be listed on the display along with their network names.
After selecting a network, choose one of the following connection methods for the Majority Fitzwilliam Connect Amp.
Using Push Button (Wi-Fi Protected Setup –WPS)
- The device will prompt you to press the WPS button on your router.
- The Majority Fitzwilliam Connect Ampwill then search for an available Push Button Connectnetwork.
Using a PIN (Personal Identification Number)
- The Majority Fitzwilliam Connect Ampwill generate an 8-digit PIN code.
- Enter this PIN into your wireless router, access point, or an external registrar device.
Skip WPS (Standard Network Key Entry)
- Select the network, then enter the network password (network key) manually, as you would for a standard encrypted network.
- Use the navigation dial or the directional buttons on the remote control to move the cursor through the characters. The selected character is displayed at the top of the screen.
- Press the OK button to confirm each character.
- Before entering the first character, three additional options are available by rotating the navigation knob: Backspace, OK, and Cancel.
- Once the password has been fully entered, select OKon screen and press the OK button to confirm and connect.
Additional Notes
- For more information on setting up a WPS-enabled network, refer to your router’s WPS instructions.
- The device will then attempt to connect to the selected network.
- ‘Connected’will be displayed if the setup is successful.
- If the connection fails, the device will return to the previous screen so you can try again.
Once the connection is complete, press OKto exit the setup wizard.
OKTIV App-Net remote
OktivApp –Net Remote

The Majority Fitzwilliam Connect Ampsupports Net Remote functionality, allowing users to control the device remotely using a smartphone or tablet (iOS or Android).
By downloading the dedicated OKTIVapp, you can access and control all available Modes, including Internet Radio, Podcasts, Spotify, DAB, FM, Bluetooth, USB playback, AUX In, Optical and Coax.
To get started:
- Search for OKTIVin the Google Play Store or Apple App Store and install the app on your smartphone or tablet.
- Ensure that both your tuner and mobile device are connected to the same Wi-Fi network.
- Launch the app.
- The app will automatically initialise and begin scanning for available devices on the network.
- Tap your Fitzwilliam Connect Ampwhen it appears in the app to establish the remote connection.
- Once connected, your mobile device will automatically reconnect to the tuner the next time you open the app, provided both are on the same network.
Note:
If another smartphone or tablet with the OKTIV app is connected to the same network and attempts to access the tuner, it will take over the current connection.
Internet Radio & Podcasts
Majority Fitzwilliam Connect Ampcan play thousands of radio stations and podcasts from around the world via a broadband internet connection. When Internet Radio or Podcasts Mode is selected, the device connects directly to the Airable portal to access online radio stations and podcasts globally. The station list is provided by the portal and is only available when the device is connected to the internet. The available content and submenus may change from time to time.
Press the Mode button on the remote control (Rem.3) or on the tuner(Ref.3)to access the Mode Menu. Use the arrow buttons or rotate theNavigation/OK dial on the tuner (Ref.2)to select an option, then press the OKbutton to enterInternet Radioor Podcasts Mode.
Select the required category and search for an internet radio station or podcast to listen to.
Internet Radio and Podcastsallow you to explore and access a wide variety of content using different search methods.
- Country (Local Stations): Browse radio stations from your own country. This option displays local stations based on your current location.
- My Favourites : Create your own list on airable.fm and synchronise it with your tuner (see page 13).
- Search: Use keywords to find specific stations. The name and description of the selected station will appear on the display.
- Location: Choose a country from the list to access radio stations from different regions around the world.
- Popular:Access a curated list of the most popular internet radio stations globally.
- Discover:Explore stations by category, such as country of origin, genre, or language.
Press BACK to return to the previous menu level.
Presets
In Internet Radio and Podcasts Mode, there are 40 preset slots available, which you can use to save radio stations and podcasts on the tuner. For more information, see page 14 (Save and Recall Radio Station Presets).
Setting up ‘My favourites’list
Airable Internet Radio: Setting Up ‘My Favourites’
The Majority Fitzwilliam Connect Ampuses the Airable portal to access thousands of internet radio stations and podcasts. This allows you to listen to a wide variety of stations and create your own favourites list. Stations can be saved directly on the tuner as presets or managed online via your Airable.fm account as ‘My Favourites’, which can then be synchronised with your tuner.
Create an Airable Account
Visit airable.fmon a computer or mobile device and register for an account using your email address and a password.
Once your account has been created, you can begin building your list of preferred internet radio stations under ‘My Favourites’.
Connect Majority Fitzwilliam Connect Amp to Your Airable Account
- Turn on your Fitzwilliam Connect Amptuner and select Internet Radiofrom the main menu.
- Navigate to My Favourites or toMy added stationsand press OK. A unique code will appear on the display (valid for 10 minutes only). This code is required to link the tuner to your Airable account.
- On the Airable.fm website, log in and go to the Devicessection. Enterthe code displayed on your tuner and confirm to connect your account.
Create Your Favourites List on Airable.fm
- Use the Airable website to browse available stations. Search for your preferred stations and add them to My Favourites.
Notes and Troubleshooting
- The pairing code only appears when the tuner is connected to Wi-Fi and My Favourites is selected. Do not confuse this feature with Presets.
- ‘My Favourites’ are stored in your Airable.fm account and can be synchronised across multiple registered devices.
- Presets are stored locally on the tuner and are not synchronised with the Airable.fm account.
- If stations do not appear, ensure the tuner is connected to the internet and that the firmware is up to date. Restarting both the tuner and your router may also help.
- For issues related to your Airable account or connection, please contact Airable.fm supportvia their official website.
Save and Recall RadioStations (Presets)
The Majority Fitzwilliam Connect Amphas a total of 90+ preset slots, which are shared across allModes (Internet Radio, Podcasts, DAB, and FM). The same method is used to save and recall stations in any of these Modes.
The store and recall functions operate in the same way across all Modes, as described below.
Storing a Radio Station as a Preset
- Presets are stored locally on the Fitzwilliam Connect Ampand cannot be accessed from other devices.
- Startplaying the radio station you wish to save.
- While the station is playing, pressand hold the FAVbutton on the remote control (Rem.12) or the Memorybutton on the tuner(Ref.4)forthree to four seconds until the presetlist appears with the title ‘Save to Preset’. If the display shows ‘Recall from Preset’, repeat the steps to open the correct menu.
- Use the Up/Downarrow buttons(Rem.7, Rem.9)to select anempty presetslot.
- Press OKto confirmand save. The display will show ‘Preset Stored’.
- Alternatively, press and hold number buttons 1–10on the remote control for three to four seconds to save presets 1–10 directly to the corresponding buttons.
Recalling a saved station from presets
- Set the tuner to the correct Mode (DAB, FM, Internet Radio, or Podcasts), depending on where the station was saved.
- PresstheFAVbutton on the remote control (Rem.12)briefly to open the ‘Recall from Preset’list.
- Use the Up/Downarrow buttons (Rem.7, Rem.9)to scroll through your saved stations.
- Press OKto play the selected station.
- If a preset slot is empty, the display will show ‘Preset Empty’.
Alternatively, for quick access to presets 1–10, press the corresponding number buttons 1–10on the remote control to play those presets directly.
Additional notes
- To delete a saved station, you can eitheroverwrite it by saving a new station to the same preset slot orperform a factory reset to clear all presets.
- Presets are stored directly on the tuner and cannot be accessed or managed from other devices.
DAB/DAB+ Radio
The Majority Fitzwilliam Connect Ampreceives DAB/DAB+ digital radio and displays information about the station, stream, and track currently playing.
Press the Modebutton on the remote control (Rem.3) or on the tuner (Ref.3) to access the Mode menu. Use the arrow buttons or rotate the Navigation/OKdial on the tuner (Ref.2) to select DAB Radio, then press OKto enter.
Scanning for Stations
Before performing a new scan, ensure the radio antenna is fully extended. The first time you select DAB Mode, or if the station list is empty, the tuner will automatically perform a full scan to search for available stations.
Once the scan is complete, the tuner will display a list of available stations. Scroll through the list using the arrow buttons on the remote control or by rotating the Navigation/OK dial. Highlight the station you wish to play, then press OKto start listening.
Select Prune Invalidto remove stations that are listed but no longer available.
To start a new scan, press and hold the Menubutton (Rem.2) on the remote control or on the tuner to enter DAB Mode settings. Scroll through the menu, select Scan, then press OKto perform a full scan.
Station Playback Information
While a station is playing, the Fitzwilliam Connect Ampdisplay shows information about the station, track, or broadcast.
Now Playing Information
The screen displays the station name and DLS (Dynamic Label Segment) information provided in real time by the broadcaster, including programmename and track title.
To view additional information, press the Infobutton repeatedly (Rem.13). Each press cycles through: DLS text, programmetype, ensemble name/frequency, signal strength/error rate, bit rate/channels, and current date.
Presets
In DAB Mode, there are 40 preset slots available, which you can use to save radio stations on the tuner. For more information, see page 14 (Save and Recall Radio Station Presets).
DAB Radio Settings Menu
While playing a radio station in DAB Mode, press and hold the Menubutton (Rem.2) on the remote control for 2–3 seconds, or the corresponding button on the tuner (Ref.5), to enter the DAB radio settings menu.
- A list of sub-menus will be displayed: Station List, Scan, Manual Tune, Prune Invalid, DRC, System Settings, and Main Menu.
- Station List–Displays the full list of DAB radio stations found after completing a full scan.
- Scan–Select this option to perform a full scan of all available DAB/DAB+ radio stations.
- Prune Invalid–Select YESto remove stations from the list that are no longer available or have no signal.
- Dynamic Range Compression (DRC)–If you are listening to music with a wide dynamic range in a noisy environment, you may wish to enable audio compression. This reduces the difference between loud and quiet sounds. You can set DRC to Off, Low, or High.
- System Settings–Access the main system settings menu, described in detail on page 22.
- Main Menu–Returns to the Mode selection menu.
FM Radio
TheMajority Fitzwilliam Connect Ampreceives analogue radio broadcasts from the FM band and displays RDS (Radio Data System) information about the station and programme, where available.
Press theModebutton onthe remote control (Rem.3) or on the tuner (Ref.3) to access the Mode menu. Use the Up/Downarrow buttons or rotate the Navigation/OK dial on the tuner (Ref.2) to select FM Radio, then pressOKto enter.
Tuning Stations
- Automatic scan with preset saving–While in FM Mode, press the Menubutton on the remote control (Rem. 2)or on the unit to enter FM settings. Select Auto Presetting; the tuner will automatically start a full scan and save the found radio stations as presets. Once completed, all saved stations will be available for recall with a short press of the FAVbutton (Rem. 12)or the Memorybutton(Ref.4)on the tuner. Select a station, then press OKto start playing. Alternatively, press and hold the OKbutton for three seconds to initiate a full scan.
- Manual Tuning –Tune manually by using the Upor Downarrow buttons on the remote control (Rem. 7, Rem. 9)or by rotating the Navigation/OKdial to search through the FM radio band. Each button press will move up or down the FM band in 0.05 MHz increments.
Now Playing Information
- While a station is playing, the screen displays its frequency. If RDS information is available, the station name, programmename, track title, and additional station details will also appear. Stereo broadcasts are indicated by an icon at the top of the screen.
- Press the Infobutton repeatedly (Rem.13) to view additional informatinif available. Each press cycles through available details, including RDS text, programmetype, frequency, and current date.
FM RadioSettings
While in FM Mode, press and hold the Menubutton (Rem.2) on the remote control for 2–3 seconds, or the corresponding button on the tuner (Ref.3), to enter the FM radio settings menu.
A list of sub-menus will be displayed: Scan Settings, Audio Settings, Auto Presetting, System Settings, and Main Menu.
- Scan Settings -By default, the radio stops at all available stations. This may result in reception of weak or unstable signals. To stop only at stations with a strong signal, select Strong Stations Onlyand confirm with Yes.
- Audio Settings -Stereo stations are played in stereo by default. However, on weak signals this may result in noise or poor audio quality. To improve reception, select Mono Onlyfor weak stations.
- Auto Presetting -Select Yes to start a new automatic scan with preset saving.
- System Settings–Enter to access the main system settings menu, described in detail on page 22.
- Main Menu–Returns to the Mode selection menu.
Presets
In FM Mode, there are 40 preset slots available, which you can use to save radio stations on the tuner. For more details, see page 14 (Save and Recall Radio Stations as Presets).
Bluetooth & Spotify Connect
Bluetooth Mode
The Majority Fitzwilliam Connect Ampcan be paired with a phone, tablet, or similar device to play audio through the system’s speakers.
Press the Modebutton on the remote control (Rem.3) or on the tuner (Ref.3) to access the Mode menu. Use the arrow buttons or rotate the Navigation/OK dial on the tuner (Ref.2) to select Bluetooth, then press OKto enter.
In Bluetooth Mode, the Fitzwilliam Connect Ampautomatically enters pairing Mode. While searching for a device, the message ‘Bluetooth Audio –Discoverable’will be shown on the display.
Enable Bluetooth on your device and select ‘Majority Fitzwilliam Connect Amp’from the list of available devices. Once selected and connected, the display will show ‘Bluetooth Connected’.
Start playing audio from your device and adjust the volume on both your device and the tuner as needed. Playback is controlled directly from your Bluetooth device.
To disconnect Bluetooth, switch the Fitzwilliam Connect Ampto a different Mode or disconnect the device from your Bluetooth settings.
Please note:The Majority Fitzwilliam Connect Ampis not compatible with Bluetooth headphones or Bluetooth speakers.
Spotify Connect (Lossless)
Use your phone, tablet, or computer as a remote control for Spotify. Go to spotify.com/connect to learn how.
The Spotify Software is subject to third party licenses, which can be found here: https://www.spotify.com/connect/third-party-licenses
Music Player –USB Playback
USB Playback
The Majority Fitzwilliam Connect Ampfeatures a USB port for playback from a USB stick of up to 128 GB. The supported audio format is MP3.
Press the Modebutton on the remote control (Rem.3) or on the tuner (Ref.3) to access the Mode menu. Use the arrow buttons on the remote control or rotate the Navigation/OKdial on the tuner (Ref.2) to select Music Player, then press OKto enter.
Insert the USB stick into the USBport (Ref.1). You will be asked if you would like to open USB folder. Select YESto open and view the content or select NOto return to previous screen. Browse through your audio files, select one and start playing.
Music Player settings–While in USB mode or during USB playback, press the Menubutton on the remote control (Rem. 2)or on the tuner (Ref.5)to enter. The following options will be displayed: USB Playback, My Playlist, Repeat Play, Shuffle, Clear My Playlist, System Settings,and Main Menu.
USB Playback
Enter to browse through files or folders using the Navigation dial on the radio or the Up/Down buttons on the remote control. The display shows folder and file names (not necessarily track titles).
Select the audio file you want to play and press OKto start playback.
My Playlist
Files or audio tracks can be added to My Playlistwhile browsing the available tracks in the USB playback menu. Highlight the track you wish to add, then press and hold OKfor two seconds to save it.
The playlist is preserved in Standby modeif the USB stick is not removed. My Playlistcan store up to 200 tracks.
To clear the entire playlist, select Clear My Playlistfrom the menu or remove the USB stick from the device.
Repeat / Shuffle
Repeat Play–Select, then press the OK button to turn repeat playback on. Press again to switch it off.
Shuffle–Audio files can be played in random order (Shuffle). Select, then press OK to turn this on. Press again to turn it off.
Please note that Repeat and Shuffle apply to the entire contents of the USB stick.
Now Playing Information
While a track is playing, the screen displays the track titleand artist. A progress bar shows the elapsedand total track time. An icon at the bottom of the screen indicates the source as USB.
Press the Infobutton to view additional information. Each press cycles through details such as artist, album, codec/sampling rate, playback buffer, and today’s date.
Important Notes
- Album cover artwork is not supportedin USB mode.
- The USB port is for playback onlyand should not be used for charging devices or as a connection port for other equipment.
Connecting External Audio Devices
The Majority Fitzwilliam Connect Amphas multiple audio ports that allow you to connect external devices for playback. Once connected, press the Modebutton on the remote control (Rem.3) or on the tuner (Ref.3) to access the Mode menu.
Use the arrow buttons or rotate the Navigation/OKdial on the tuner (Ref.2) to select the audio source you have connected, such as AUX IN, Optical, or Coaxial.
Audio Input L/R (analogue RCA inputs)
The AUX INMode allows you to play audio from an external source such as an MP3 player, tablet, or similar device through the Majority Fitzwilliam Connect Amp, using an RCA-to-3.5 mm AUX cable or RCA-to-RCA cable (not included).
Connect the external audio source to the Audio Input (RCA L/R)ports (Ref.22) on the Fitzwilliam Connect Amp. Adjust the volume on both the tuner and the connected device as required. Playback is controlled from the external device.
RCA Pre-Out ( Line output)
The RCA Pre-Outallows you to send audio from the Fitzwilliam Connect Ampto an external device, such as active speakers, using RCA cables.
Before connecting, reduce the volume on the tuner. Connect the external device to the RCA L/R Pre-Out ports(Ref.21), then adjust the volume as required. Playback is controlled from the tuner.
Optical Input
The Optical InMode allows audio playback from an external device through the Fitzwilliam Connect Amp.
Before connecting, reduce the volume on both the tuner and the external device (if adjustable). Connect the external device to the Optical Input port(Ref.23), then adjust the volume and control playback from the external device.
Coaxial Input
Connect your device to the Coaxial Input port(Ref.24) for digital audio playback.
Headphone port (Audio Output)
Connect wired headphones (not included) with a 3.5 mm jack to the headphone port(Ref.14) on the Fitzwilliam Connect Ampfor private listening.
Before connecting, ensure the volume is set to a low or medium level, then adjust as required.
Dual Alarm and Sleep Timer
Alarm Setup
The Majority Fitzwilliam Connect Ampfeatures two versatile wake-up alarms with a snooze function and a sleep timer, allowing the system to switch off automatically after a set period. Each alarm can be configured to start in a selected Mode.
While the tuner is in working Mode, press and hold the Menubutton (Rem.2) on the remote control for 2–3 seconds, or the corresponding button on the tuner (Ref.5). Scroll through the menu and select Main Menu, then select Alarms. Press OKto enter the alarm settings.
- Select the alarm number (Alarm 1or Alarm 2) and configure the following parameters:
- Enable–Set the alarm frequency to Daily, Once, Weekends, Weekdays, or Off.
- Time–Set the desired alarm time.
- Mode–Select the alarm source: Buzzer, Internet Radio, DAB, or FM.
- Preset–Select Last Listened station or choose a saved station from your preset list.
- Duration–Select how long you would like the alarm to sound: 15, 20, 30, 45, 60, 90, or 120 minutes.
- Volume–Set the desired alarm volume level.
To save your settings, scroll down and select Save, then press OKto confirm. An alarm icon will appear in the bottom-left corner of the display to indicate that the alarm is active.
At the set time, the alarm will sound. To temporarily silence the alarm, pressSleep/Snoozebuttonon remote control (Rem.21). The snooze period can be adjusted as required to 5, 15 or 30 minutes. During snooze, the tuner returns to standby mode, and a flashing alarm icon will be displayed.
Press the Power/Standbybutton to switch off the alarm completely.
Sleep Timer
To set the sleep timer, select Sleepfrom the Main Menu. Alternatively, press the Sleepbutton on the remote control (Rem.21).
Choose a duration from Off, 15, 30, 45, or 60 minutes. Once set, the tuner will begin counting down and will automatically switch to Standby Mode when the selected time has elapsed.
System Settings
While the Majority Fitzwilliam Connect Ampis on the playing screen in any Mode, pressthe Menubutton (Rem.2)on the remote control for 2–3 seconds, or the corresponding button on the tuner (Ref.5). Scroll through the menu, then select and enter System Settingsto access the following options:
Equaliser
The tuner offers several preset EQ (equaliser) Modes: Normal, Flat, Jazz, Rock, Movie, Classic, Pop, Newsand My EQ. You can customiseMy EQby adjusting the bass, treble and loudness to your preference within the My EQ Setupmenu. Once configured, select My EQas your active equaliser Mode.
Streaming Audio Quality–Select Low, Medium, or High.
Network
Network Wizard–Use this to search for available Wi-Fi networks (SSID –Service Set Identifier, the network name). Enter the WEP/WPA password if required or choose Push Button (WPS)or PINto connect automatically if your router supports WPS or PIN-based pairing.
PBC WLAN Setup–Uses Push Button Configuration (WPS) for easy connection to compatible routers.
View Settings–Displays information about the currently connected network, including connection status, MAC address (unique network identifier), WLAN region, DHCP (Dynamic Host Configuration Protocol, which automatically assigns an IP address), SSID (network name), IP address, subnet mask, gateway address, primary DNS, and secondary DNS.
Manual Settings–Allows manual selection of network settings and enables or disables DHCP if you prefer to assign network details manually.
Network Profile–The tuner can store up to four previously connected Wi-Fi networks and will automatically attempt to reconnect when they are available. You can view saved networks here and delete any by selecting the network, pressing OK, and confirming with YES.
Clear Network Settings–Select YESto delete all saved network settings, or NOto cancel.
Keep Network Connected–Select YESto keep the Wi-Fi connection active in standby Mode. This allows control via the OKTIV app at all times.SelectNOto deactivate the Wi-Fi connection.
Time/Date
Set the time and date manually or enable automatic updates. You can also select the time format, time zone, and daylight saving settings. Daylight saving should be set to ONin March when clocks move forward to summer time and set to OFFin October when clocks return to standard time.
Language
The default language is English. Select your preferred language from the list of available options, then press OKto confirm.
System Settings
Factory Reset
A factory reset will restore all user settings to their default values. This will erase any existing presets, time and date settings, and network configurations.
Software Update
Auto-Check Setting–Automatically checks for new software updates at regular intervals. Automatic updates are enabled by default. To disable this function, select NO. To re-enable it, select YES.
Check Now–Immediately searches for available software updates.
If a new software version is available, you will be prompted to confirm the update. Once confirmed, the software will be downloaded and installed. All user settings will be retained after the update.
Note:Before starting a software update, ensure the tuner is connected to a stable mains power supply. Disconnecting power during the update process may permanently damage the unit.
Setup Wizard
You can start the setup wizard at any time. Any previously saved settings or stations will not be deleted.
Info
Access this section to view the firmware version and tuner ID.
Backlight (Display Brightness Settings)
This menu allows you to set the display brightness for both operating and standby Modes.
- Timeout–Sets the time after which the display will dim according to the levels defined in On Leveland Dim Level.Available options: ON, 10, 20, 30, 45, 60, 90, 120, or 180 seconds.If ONis selected, the brightness levels set for On Leveland Dim Levelwill remain active at all times without dimming.
- On Level–Sets the display brightness during normal operation. Choose fromMedium,Low or off then press OKto confirm.
- Dim Level–Sets the display brightness when the tuner is in standby Mode. Choose from High, Medium, Low, or Off, then press OKto confirm.
Troubleshooting


Product Specifications
Product Specifications

Saving Energy (ERP)
The Fitzwilliam Connect Amp will power off automatically after 15 minutes of inactivity.
To resume operation, simply press the Power ON/OFF button.
How to activate wireless network port:
- Connect the unit with power.
- Switch to wireless Mode (e.g. Internet)
How to deactivate wireless network connection: - Go to Main Menu – System settings – Network – Keep network connected. Select NO, and then press the ‘OK’ button to keep network disconnected.
Standby power consumption:
WiFi OFF in standby Mode: <0.8W
WiFi ON in standby Mode: <2W
Support & Warranty
Support
Thank you for purchasing the Majority Fitzwilliam Connect Amp. Please follow the guidance of the manual to set up your device and enjoy its fantastic features. If you require further assistance with your Majority product, please contact ourteam on the Majority website: www.majorityaudio.com/support or email us @ techsupport@majority.co.uk.
Warranty
All products come with a standard 12-month warranty. All items must be registered within 30 days of purchase viawww.majorityaudio.com for the warranty to be valid. Once on the web page, use the menu to find ‘Register Your Product’. You will also be given the chance to extend your warranty for an additional 24 months, free of charge.
Warning & Safety Information
Safety and Usage Guidelines (All where applicable)
General Safety Information -Read and Retain: Review all safety and operating instructions before use; keep them for future reference.
Follow Instructions: Adhere strictly to all safety and operational guidelines.
Water Exposure: Keep the device away from water; avoid placing liquids near it.
Ventilation:Ensure ventilation openings are unobstructed to prevent overheating.
Heat Sources: Keep the device away from heat-emitting appliances.
Wall Mounting -Installation Safety: Follow the manufacturer’s instructions and use approved mounting kits only. Avoid drilling into areas with cables, gas, or water lines. Use proper tools and safety apparatus.
Regular Maintenance:Inspect regularly for wear or damage, especially if wall-mounted.
Relocation: Detach from the wall mount before moving.
Child Safety: Keep out of children’s reach and ensure heavy items are securely mounted.
Seismic Precautions: Use specialized mounts in earthquake-prone areas.
Electrical Safety -Power Source: Use the specified power source; consult an electrician if unsure.
Cable Management: Protect the power cord from damage.
Power Disconnection: Keep the main plug accessible; unplug during storms or long periods of non-use.
Battery Safety -Charging: Use the manufacturer’s charger; avoid extreme conditions.
Heat Exposure: Keep batteries away from heat to prevent explosion or leakage.
Battery Condition: Discontinue use if the battery is damaged; dispose of it properly.
Replacement: Only use recommended batteries; incorrect types can cause hazards.
External Batteries: Use only specified types, observing correct polarity.
Battery Removal: Remove batteries if not used for an extended period.
Disposal: Follow local regulations for battery disposal; do not incinerate.
Connectivity Safety -Cable Connections: Power off devices before connecting or disconnecting cables.
Bluetooth Pairing: Ensure a secure connection; avoid interference from other devices.
Volume Control: Keep volume Moderate to prevent hearing damage.
Connectivity and Data Security -Wireless Security: Review privacy policies and secure your network.
Software Updates: Keep software updated for security and performance.
Children’s Safety Warnings -Product Use: Intended for adults; keep away from children.
Battery Warning: Keep batteries and items containing batteries out of children’s reach. Volume Control: Maintain a safe volume level to protect children’s hearing.
Fire Hazard -Flammable Materials: Do not place open flames near the product.
Overheating: Avoid covering the product to prevent overheating and fire risks.
Disposal and Recycling -Product Disposal: Dispose of at a recycling centreaccording to local laws.
Environmental Compliance:Follow regulations for battery and electronic waste disposal.
User Maintenance -Cleaning: Unplug before cleaning; use a dry cloth only.
Servicing: Only qualified personnel should perform repairs.
Data Protection: Reset to factory settings before returning or disposing of the product.
Disclaimer: Failure to follow these instructions may result in injury, death, or property damage. The manufacturer is not liable for damage caused by improper use.
Declaration of Conformity:
We, iZillaLimited,1 Cygnus Business Park, Middlewatch, Swavesey, Cambridgeshire CB24 4AA, declare under our sole responsibility that the product:
Product Name:Fitzwilliam Connect Amp Model:10000031143 Brand Name: Majority
To which this declaration referred is in conformity to the following harmonized standards or normative documents (CE & Rohs 2.0) ;
EN 55035:2017, EN 55032:2015, EN61000-3-2:2014, EN61000-3-3:2013, EEN62368-1:2004+A11:2017, ETSI EN 301 489-1 V2.2.3(2019-11), ETSI EN 301 489-17, V3.2.2(2019-12), ETSI EN 300 328 V2.2.2 (2019-07), EN 62479: 2010, IEC 62321-3-1:2013, IEC 62321-4:2013, IEC 62321-5:2013, IEC 62321-6:2015, IEC 62321-7-1:2015, IEC 62321-7-2:2017, IEC 62321-8:2017, (EC)NO 1275/2008,EN50564:2011, (EC)NO 801/2013.
Complying with the requirements or provisions of Council Directives which relate to:
EMC Directive 2014/30/EU, RED Directive 2014/53/EU, LVD Directive 2014/35/EU, Directive (2011/65/EU) and its amendment directives 2015/863/EU (RoHS 2.0) of the, European parliament, ERP Directive 2009/125/EC.
All essential test suites have been carried out.
Point of Contact:Eddie Latham | Founder
Importer’s Addresses:
UK: iZilla Limited,1 Cygnus Business Park, Middlewatch, Swavesey, Cambridgeshire CB24 4AA
Email: techsupport@majority.co.uk
EU RP: AR Experts, Po Box 5047, 3620 AA Breukelen, The Netherlands
Email: info@ar-experts.eu
US: iZilla Ltd C/O A.N.Deringer Inc, 19520 Wilmington Ave, Rancho Dominguez, CA, 90220
Email: techsupport@majority.co.uk

Statement of Compliance
Product Security and Telecommunications Infrastructure Act 2022and the Product Security and Telecommunications Infrastructure (Security Requirements for Relevant Connectable Products) Regulations 2023
1. Responsible Person
Company Name:IZILLA LIMITED (Company No. 08520738)Registered Office:1 Cygnus Business Park, Middlewatch, Swavesey, Cambridgeshire CB24 4AAContact for Compliance Purposes:info@majority.co.uk
2. Product Identification
Product Range Name:Majority StreamersBrand:MajorityModels Covered:Fitzwilliam Connect Amp
Product Description:Consumer connectable streaming audio products capable of network connectivity for media playback and control.
3. Declaration of Compliance
IZILLA LIMITED declares that, in our opinion, theproductsidentifiedin Section 2comply withthe applicable security requirements under the Product Security and Telecommunications Infrastructure Act 2022 and the associated Regulations.
4. Security Requirements Met
4.1 No Universal Default Passwords
The products are not supplied with universal default passwords. Where authentication is used, the product uses unique credentials and or requires the user to set credentials during setup, as applicable.
4.2 Vulnerability Disclosure Policy
A vulnerability reporting process exists for these products. Security issues and vulnerabilities can be reported to:info@majority.co.uk
4.3 Security Update Commitment
Security updates will be provided for a minimum period of10 yearsfrom the date of first UK sale. Information on security updates is available via:https://www.majority.co.uk/support
5. Supporting Evidence
IZILLA LIMITEDmaintainsdocumentation to support this declaration, which may include:
• Default password and authentication approach
• Vulnerability intake and handling process
• Security update policy and support period records
• Relevant technical and compliance records
This information will be made available to UK enforcement authorities on request.
6. Signature
Signed for and on behalf ofIZILLA LIMITED:
Name:E LathamPosition:OwnerDate:1stJan 2026



Read More About This Manual & Download PDF:
Documents / Resources
![]() | Fitzwilliam Connect Amp |
References
- Login to your accountairable.fm
- Language selection | European Commissionexperts.eu
- Spotify - Connectspotify.com
- Support – Majoritywww.majority.co.uk
- Third Party Licenses | Spotify for Developerswww.spotify.com
- User Manualmanual.tools
