COMPEX WPQ618 Hardware

Full Specifications
| Model Number | WPQ618 |
| SoC | Qualcomm IPQ6018 ‘Cypress’ Series, Quad-Core ARM 64-bit A53 @ 1.8 GHz |
| Reference Design | Qualcomm Atheros CP01 |
| System Memory | 1GB (2× 512MB) DDR3L, 16-bit interface, 32-bit memory bus |
| NAND Flash | 256MB |
| NOR Flash | 32MB |
| Wi-Fi Standard | IEEE 802.11ax (Wi-Fi 6) – backward compatible to 802.11a/b/g/n/ac |
| 2.4GHz Radio | On-board 2×2 MU-MIMO OFDMA 802.11b/g/n/ax; max 20dBm per chain; up to 573 Mbps |
| 5GHz Radio | On-board 2×2 MU-MIMO OFDMA 802.11a/n/ac/ax; max 20dBm per chain; up to 1201 Mbps |
| Frequency Ranges | 2.4GHz: 2.412 ~ 2.472GHz5GHz: 5.150 ~ 5.825GHz |
| Modulation | OFDMA: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM |
| Advanced RF Features | Supports Dynamic Frequency Selection (DFS) |
| Antenna Connectors | 4× U.FL connectors (2 per band) |
| M.2 (NGFF) Slots | 1× B Key with PCIe 3.0 (5G modem) + 1× B Key with USB 3.0 |
| SIM Card Slots | 4× SIM card slots |
| SD Card Slot | 1× SD card slot |
| Ethernet Ports | 4× 1Gbps LAN/WAN RJ45 + 1× 2.5Gbps LAN RJ45 |
| USB | 1× USB 2.0 Port |
| Bluetooth | CSR8811, BLE 4.2 |
| Audio / SLIC | 1× 30-pin Audio/SLIC interface |
| PoE | IEEE 802.3at, 48~56V, via 2.5Gbps LAN port |
| Serial Debug | 1× Serial 4-Pin Connector (TTL) |
| JTAG | 1× JTAG 20-Pin Connector |
| Reset | 1× Hardware Reset Button + 1× Software Reset Button |
| Boot Configuration | 1× DIP Switch (S7): SPI NOR (default), eMMC, QPIC/NAND, or USB2.0 |
| LED Indicators | 8-LED status array |
| Power Interface | 1× DC Jack (12V) or PoE (48~56V via 2.5Gbps LAN port) |
| Max Power Consumption | 17.5W (board only, including Bluetooth) |
| Dimensions (W×H×D) | 128mm × 210mm × 33.9mm (with heatsink) |
| Operating Temperature | -20°C to 70°C |
| Storage Temperature | -40°C to 90°C |
| Operating Humidity | 5% to 95% (non-condensing) |
| Storage Humidity | Max. 90% (non-condensing) |
| OS / Firmware | CompexWRT |
| Certification | REACH & RoHS Compliant |
| Ordering Code | WPQ618HV 6A03PR321GBR-5G |
Introduction
- Thank you for choosing the Compex WPQ618. This document provides complete hardware integration guidance for engineers and system developers deploying the WPQ618 in embedded, industrial, and networking platforms.
- The WPQ618 is a multi-function embedded board powered by Qualcomm’s IPQ6018 ‘Cypress’ Series quad-core ARM Cortex-A53 processor running at 1.8GHz. The board integrates dual-band 2×2 MU-MIMO Wi-Fi 6 radio directly on-board, an on-board Bluetooth 4.2 BLE module, two M.2 (NGFF) B Key expansion slots for a 5G cellular modem and companion module, four SIM card slots, PoE input, and multiple high-speed Ethernet ports, delivering a flexible platform for networking product development.
Key Highlights
- Qualcomm IPQ6018 ‘Cypress’ Quad-Core ARM 64-bit A53 @ 1.8 GHz SoC for network processing.
- Dual-band Wi-Fi 6 (802.11ax) integrated on-board — 2×2 MU-MIMO OFDMA on both 2.4GHz and 5GHz.
- On-board wireless: 2.4GHz 802.11b/g/n/ax, max 20dBm per chain, up to 573 Mbps; 5GHz 802.11a/n/ac/ax, max 20dBm per chain, up to 1201 Mbps.
- 1× M.2 (NGFF) B Key socket with PCIe 3.0, supporting a 5G cellular modem.
- 1× M.2 (NGFF) B Key socket with USB 3.0 for companion module expansion.
- On-board Bluetooth via CSR8811, BLE 4.2.
- Multi-Ethernet: 4× 1Gbps RJ45 ports + 1× 2.5Gbps RJ45 port.
- × USB 2.0 port for external storage and peripherals.
- 1× Audio/SLIC interface (30-pin) for telephony/audio applications.
- Power over Ethernet (PoE) input — supports IEEE 802.3at, 48~56V.
- Onboard memory: 1GB (2× 512MB) DDR3L (16-bit interface, 32-bit memory bus), 256MB NAND Flash, and 32MB NOR Flash.
- 1× hardware reset button, 1× software reset button, 1× boot configuration DIP switch (S7), and an 8-LED status array.
- CompexWRT firmware.
- REACH and RoHS compliant.
Intended Use
The WPQ618 is an engineering-grade embedded board intended for OEM/ODM integration and product development. Typical target applications include:
- 802.11ax MU-MIMO OFDMA Wi-Fi 6 access points and dual-band router platforms.
- Mesh router supporting Easymesh.
- Smart AP TWT.
Package Contents
Verify the following items are included in the package before proceeding with installation:
Checklist
1 × WPQ618 embedded board
Note: External antennas (U.FL pigtail cables), M.2 (NGFF) expansion modules, SIM cards, SD card, Ethernet cables, and power supply are not included unless specified in the order. Contact sales@compex.com.sg for accessory options.
If any item is missing or damaged, contact Compex Technical Support (see Chapter 11) before proceeding.
Hardware Overview
The WPQ618 is a fully integrated embedded networking platform based on the Qualcomm IPQ6018 SoC. Dual-band 2×2 MU-MIMO Wi-Fi 6 radio, on-board Bluetooth 4.2, routing, and switching are handled entirely on-board, with two M.2 (NGFF) B Key slots available for 5G cellular modem and companion module expansion.
Board Layout
The WPQ618 features the following major components and connectors:

| SoC | Qualcomm IPQ6018 ‘Cypress’ Series, Quad-Core ARM 64-bit A53 @ 1.8 GHz |
| Reference Design | Qualcomm Atheros CP01 |
| System Memory | 1GB (2× 512MB) DDR3L, 16-bit interface, 32-bit memory bus |
| Flash Storage | 256MB NAND Flash + 32MB NOR Flash |
| On-Board Wi-Fi | 2×2 2.4GHz MU-MIMO 802.11b/g/n/ax, max 20dBm per chain 2×2 5GHz MU-MIMO 802.11a/n/ac/ax, max 20dBm per chain |
| RF Connectors | 4× U.FL connectors (2 per band: 2.4GHz, 5GHz) |
| M.2 (NGFF) Slots | 1× M.2 B Key socket with PCIe 3.0, for 5G cellular modem 1× M.2 B Key socket with USB 3.0 |
| SIM / SD Card Slots | 4× SIM card slots + 1× SD card slot |
| Ethernet Ports | 4× 1Gbps LAN/WAN RJ45 + 1× 2.5Gbps LAN RJ45 |
| USB | 1× USB 2.0 Port |
| Bluetooth | CSR8811, BLE 4.2 |
| Audio / SLIC Interface | 1× 30-pin header for telephony/audio applications |
| PoE Input | Supports IEEE 802.3at, 48~56V, via the 2.5Gbps port |
| Serial / Debug | 1× Serial 4-Pin Connector (TTL) + 1× JTAG 20-Pin Connector |
| Other I/O | 1× Hardware Reset Button, 1× Software Reset Button, 1× Boot Configuration DIP Switch (S7), 8-LED Status Array |
| Form Factor | 128mm × 210mm × 33.9mm (with heatsink) |
Connector Descriptions
Ethernet Ports (RJ45)
- 4× 1Gbps LAN/WAN RJ45 ports and 1× 2.5Gbps LAN RJ45 port for wired network connectivity.
- PoE input on the 2.5Gbps LAN port, supporting IEEE 802.3at, 48~56V — allows the board to be powered directly over the Ethernet cable.
- All ports support auto-MDI/MDIX and auto-negotiation.
USB Port
1× USB 2.0 Port for external storage, peripherals, or firmware upgrade via USB.

M. 2 (NGFF) B Key Slot
- 1× M.2 B Key slot with PCIe 3.0 — designed for a 5G cellular/LTE modem module, enabling WAN failover or primary cellular connectivity.
- 1× M.2 B Key slot with USB 3.0 — for a companion module such as additional wireless connectivity or storage expansion.

SIM Card & SD Card Slots
- 4× SIM card slots for cellular modem connectivity.
- 1× SD card slot for external storage expansion, such as logging or firmware images.

Audio / SLIC Interface
- 1× 30-pin header providing audio and SLIC (Subscriber Line Interface Circuit) signals —for telephony/VoIP or analog audio applications.

FL RF Connectors
- 4× U.FL connectors total, providing 2 connectors per band: 2× for the 2.4GHz onboard radio, 2× for the 5GHz onboard radio.
- Connect suitable external antennas rated for the respective frequency band.

Power Connector
- 1× DC Jack Connector, 12V DC input.
- Maximum board-only power consumption: 17.5W (including Bluetooth).
- Alternatively, power can be supplied via PoE (IEEE 802.3at, 48~56V) on the 2.5Gbps LAN RJ45 port; do not connect both DC and PoE power sources simultaneously unless the board’s power arbitration circuitry supports it.

Bluetooth
On-board CSR8811 module supporting Bluetooth 4.2 and BLE (Bluetooth Low Energy), suitable for peripheral pairing and short-range device management applications.

Serial / JTAG Debug Interface
- Serial: 4-pin TTL header (DVDD_3V3, UART_TXD_CONN, UART_RXD_CONN, GND) for serial console access during firmware development and debugging. A Serial Converter (TTL to RS-232) is available for standard serial debugging.
- JTAG: 20-pin header for low-level firmware programming and hardware debugging. A JTAG kit is available for writing self-developed loaders and firmware directly.

Reset Buttons
- Hardware Reset Button: performs a hardware-level reset of the board.
- Software Reset Button: press once for software reset (reboot).

LED Indicators
LED
- Power LED (LED2): Solid green when powered, fully booted and operational.
- LED1, LED6, LED7, LED8: 1GbE LAN/WAN port connection status.
- LED3 – 2.4GHz WiFi: Indicates 2.4 GHz on-board Wi-Fi radio activity.
- LED4 – 5GHz WiFi: Indicates 5 GHz on-board Wi-Fi radio activity.
- LED5: NAPA_LED

Hardware Pinouts
Ethernet LAN/WAN Port Pin Assignment
| Ethernet LAN/WAN Port (RJ45 1Gbps) | |
| Pin | Signal |
| 1 | 1G_CH0_P |
| 2 | 1G_CH0_N |
| 3 | 1G_CH1_P |
| 4 | 1G_CH2_P |
| 5 | 1G_CH2_N |
| 6 | 1G_CH1_N |
| 7 | 1G_CH3_P |
| 8 | 1G_CH3_N |
Ethernet LAN Port Pin Assignment
| Ethernet LAN Port (RJ45 2.5Gbps) | |
| Pin | Signal |
| 1 | 2.5G_CH0_P |
| 2 | 2.5G_CH0_N |
| 3 | 2.5G_CH1_P |
| 4 | 2.5G_CH2_P |
| 5 | 2.5G_CH2_N |
| 6 | 2.5G_CH1_N |
| 7 | 2.5G_CH3_P |
| 8 | 2.5G_CH3_N |
Serial Interface Pin Assignment
| 4-Pin UART | |
| Pin | Signal |
| 1 | DVDD_3V3 |
| 2 | UART_TXD_CONN |
| 3 | UART_RXD_CONN |
| 4 | GND |
JTAG Interface Pin Assignmen
| Pin | Signal | Pin | Signal |
| 1 | VDD_1V8 | 2 | VDD_1V8 |
| 3 | JTAG_TRSTN | 4 | NC |
| 5 | JTAG_TDI | 6 | GND |
| 7 | JTAG_TMS | 8 | GND |
| 9 | JTAG_TCK | 10 | GND |
| 11 | PULL UP_1V8 | 12 | GND |
| 13 | JTAG_TDO | 14 | GND |
| 15 | JTAG_SRSTN | 16 | GND |
| 17 | GND | 18 | GND |
| 19 | GND | 20 | GND |
SIM Slot Pin Assignment
| Pin | Signal |
| 1 | VCC |
| 2 | RST |
| 3 | CLK |
| 4 | CD |
| 5 | GND |
| 6 | NC |
| 7 | I/O |
SD Card Slot Pin Assignment
| Pin | Signal |
| 1 | SDC1_DATA_2 |
| 2 | SDC1_DATA_3 |
| 3 | SDC1_CMD |
| 4 | VDD_3V3 |
| 5 | SDC1_CLK |
| 6 | GND |
| 7 | SDC1_DATA_0 |
| 8 | SDC1_DATA_1 |
| 9 | SDC1_DETECT |
| 10 | GND |
Audio / SLIC Interface Pin Assignment
| Pin | Signal | Pin | Signal |
| 1 | BLSP4_SCL | 2 | CYP_AUDIO_BCLK |
| 3 | BLSP4_SDA | 4 | NC |
| 5 | ADC_RST | 6 | GND |
| 7 | PWM_LED_RST | 8 | PDM_CLK1 |
| 9 | MUTE_ON | 10 | PDM_DATA1 |
| 11 | KYPD_HOME_N | 12 | GND |
| 13 | MIC_VOL_P | 14 | EXT_MCLK2_ADC |
| 15 | MIC_KPD_PWR_N | 16 | NC |
| 17 | MIC_VOL_M | 18 | GND |
| 19 | AUDIO_MUTE_BUT | 20 | PDM_CLK0 |
| 21 | VDD_3V3 | 22 | PDM_DATA0 |
| 23 | GND | 24 | GND |
| 25 | VDD_1V8 | 26 | VDD_5V |
| 27 | VDD_1V8 | 28 | VDD_5V |
| 29 | GND | 30 | GND |
LED Array Assignment
| Location | Signal |
| LED1 | P1_1000_LED |
| LED2 | POWER_LED |
| LED3 | 2G_LED |
| LED4 | 5GM_LED |
| LED5 | NAPA_LED |
| LED6 | P3_1000_LED |
| LED7 | P4_1000_LED |
| LED8 | P2_1000_LED |
Boot Configuration DIP Switch (S7)
| Boot_Config Switch (S7) | |||
| Boot_Config | Boot-up Interface Select | ||
| 1 | 2 | 3 | |
| off | off | off | SPI NOR (default) |
| off | off | on | eMMC |
| off | on | off | QPIC, Parallel NAND |
| off | on | on | USB 2.0 |
| on | off | off | SPI-NOR-GPT |
| 4 | Boot up interface select | ||
| off | Boot from code RAM (default) | ||
| on | Boot from ROM | ||
M.2 B Key Slot Pin Assignment
| M.2 B Key Slot with USB3.0 | |||
| Top side | Bottom side | ||
| 1 | NC | 2 | VDD_3V7 |
| 3 | GND | 4 | VDD_3V7 |
| 5 | GND | 6 | FULL_Card_off |
| 7 | USB0_DP | 8 | WAN_DISABLE |
| 9 | USB0_DM | 10 | NC |
| 11 | GND | ||
| Mechanical key B | |||
| 21 | NC | 20 | NC |
| 23 | NC | 22 | NC |
| 25 | NC | 24 | NC |
| 27 | GND | 26 | NC |
| 29 | USB0_SS_RXN | 28 | NC |
| 31 | USB0_SS_RXP | 30 | SIM1_RST |
| 33 | GND | 32 | SIM1_CLK |
| 35 | USB0_SS_TXN | 34 | SIM1_I/O |
| 37 | USB0_SS_TXP | 36 | SIM1_VCC |
| 39 | GND | 38 | NC |
| 41 | NC | 40 | SIM2_CD |
| 43 | NC | 42 | SIM2_I/O |
| 45 | GND | 44 | SIM2_CLK |
| 47 | NC | 46 | SIM2_RST |
| 49 | NC | 48 | SIM2_VCC |
| 51 | GND | 50 | NC |
| 53 | NC | 52 | NC |
| 55 | NC | 54 | NC |
| 57 | GND | 56 | NC |
| 59 | NC | 58 | NC |
| 61 | NC | 60 | NC |
| 63 | NC | 62 | NC |
| 65 | NC | 64 | NC |
| 67 | NC | 66 | SIM1_CD |
| 69 | NC | 68 | NC |
| 71 | GND | 70 | VDD_3V7 |
| 73 | GND | 72 | VDD_3V7 |
| 75 | NC | 74 | VDD_3V7 |
| M.2 B Key Slot with PCIe3.0 | |||
| Top side | Bottom side | ||
| 1 | NC | 2 | VDD_3V7 |
| 3 | GND | 4 | VDD_3V7 |
| 5 | GND | 6 | FULL _Card _off |
| 7 | NC | 8 | WAN_DISABLE |
| 9 | NC | NC | |
| 11 | GND | ||
| Mechanical key B | |||
| 21 | NC | 20 | NC |
| 23 | NC | 22 | NC |
| 25 | NC | 24 | NC |
| 27 | GND | 26 | NC |
| 29 | NC | 28 | NC |
| 31 | NC | 30 | SIM5_RST |
| 33 | GND | 32 | SIM5_CLK |
| 35 | NC | 34 | SIM5_I/O |
| 37 | NC | 36 | SIM5_VCC |
| 39 | GND | 38 | NC |
| 41 | PCIE_RX_N | 40 | SIM4_CD |
| 43 | PCIE_RX_P | 42 | SIM4_I/O |
| 45 | GND | 44 | SIM4_CLK |
| 47 | PCIE_TX_N | 46 | SIM4_RST |
| 49 | PCIE_TX_P | 48 | SIM4_VCC |
| 51 | GND | 50 | PCIE_RST |
| 53 | PCIE_REFCLKN | 52 | PCIE_WAKE |
| 55 | PCIE_REFCLKP | 54 | NC |
| 57 | GND | 56 | NC |
| 59 | NC | 58 | NC |
| 61 | NC | 60 | NC |
| 63 | NC | 62 | NC |
| 65 | NC | 64 | NC |
| 67 | NC | 66 | SIM5_CD |
| 69 | NC | 68 | NC |
| 71 | GND | 70 | VDD_3V7 |
| 73 | GND | 72 | VDD_3V7 |
| 75 | NC | 74 | VDD_3V7 |
GPIO Pin Mapping
| GPIO PIN | Function | GPIO PIN | Function |
| GPIO_0 | AUDIO_MUTE_BUT | GPIO_1 | QPIC_BUSY_N |
| GPIO_2 | MIC_VOL_M | GPIO_3 | QPIC_WE_N |
| GPIO_4 | QPIC_RE_N | GPIO_5 | QPIC_DAT4 |
| GPIO_6 | QPIC_DAT5 | GPIO_7 | QPIC_DAT6 |
| GPIO_8 | QPIC_DAT7 | GPIO_9 | WPS |
| GPIO_10 | QPIC_CLE_N | GPIO_11 | QPIC_NAND_CE_N |
| GPIO_12 | QPIC_DAT1 | GPIO_13 | QPIC_DAT2 |
| GPIO_14 | QPIC_DAT3 | GPIO_15 | QPIC_DAT0 |
| GPIO_16 | MIC_KPD_PWR_N | GPIO_17 | QPIC_ALE |
| GPIO_18 | KYPD_HOME_N | GPIO_19 | Boot_Config(PULL_DOWN) |
| GPIO_20 | Boot_Config(PULL_DOWN) | GPIO_21 | MUTE_ON |
| GPIO_22 | ADC_RST | GPIO_23 | WSA_SWR_CLK |
| GPIO_24 | WSA_SWR_DATA | GPIO_25 | PWM_LED_RST |
| GPIO_26 | Boot_Config(PULL_DOWN) | GPIO_27 | WSA_EN_R |
| GPIO_28 | WSA_EN_L | GPIO_29 | PDM_CLK0 |
| GPIO_30 | PDM_DATA0 | GPIO_31 | PDM_CLK1 |
| GPIO_32 | PDM_DATA1 | GPIO_33 | EXT_MCLK2_ADC |
| GPIO_34 | MIC_VOL_P | GPIO_35 | LED_5G |
| GPIO_36 | PCIE_WAKE | GPIO_37 | LED_2GS |
| GPIO_38 | SPI0_CLK | GPIO_39 | SPI0_CS_NI |
| GPIO_40 | SPI0_MISO | GPIO_41 | SPI0_MOSI |
| GPIO_42 | BLSP4_SCL | GPIO_43 | BLSP4_SDA |
| GPIO_44 | BLSP2_UART_RX | GPIO_45 | BLSP2_UART_TX |
| GPIO_46 | BLSP5_SCL | GPIO_47 | BLSP5_SDA |
| GPIO_48 | NC | GPIO_49 | Boot_Config(PULL_DOWN) |
| GPIO_50 | LED_USB0 | GPIO_51 | BT_PRIORITY_PTA11 |
| GPIO_52 | WLA_ACTI_PTA12 | GPIO_53 | BT_ACT_PTA10 |
| GPIO_54 | Boot_Config(PULL_DOWN) | GPIO_55 | WAN_DISABLE |
| GPIO_56 | FULL_Card_off | GPIO_57 | NC |
| GPIO_58 | NC | GPIO_59 | PCIE_CLK_REQ |
| GPIO_60 | PCIE_RSTn | GPIO_61 | NC |
| GPIO_62 | SD_DET | GPIO_63 | SD_WP |
| GPIO_64 | MDC | GPIO_65 | MDIO |
| GPIO_66 | SD_LDO_EN | GPIO_67 | NC |
| GPIO_68 | NC | GPIO_69 | SPI_CLK_UART_RTSn |
| GPIO_70 | SPI_CS_UART_CTSn | GPIO_71 | SPI_MISO_UART_RX |
| GPIO_72 | SPI_MOSI_UART_TX | GPIO_73 | NC |
| GPIO_74 | NC | GPIO_75 | Malibu_RESET |
| GPIO_76 | NAPA_INT0 | GPIO_77 | NAPA_RESET |
| GPIO_78 | QTZ_INT | GPIO_79 | QTZ_RESET |
Wi-Fi Specifications
Wi-Fi Capability
The WPQ618 features fully integrated dual-band 2×2 MU-MIMO Wi-Fi 6 radios operating on the 2.4GHz and 5GHz bands. Both radios are driven by the Qualcomm IPQ6018 SoC and require no external radio modules.
| Wi-Fi Standard | IEEE 802.11ax (Wi-Fi 6) – backward compatible to 802.11a/b/g/n/ac |
| 2.4GHz Radio | 2×2 MU-MIMO 802.11b/g/n/ax; max 20dBm per chain; up to 573 Mbps |
| 5GHz Radio | 2×2 MU-MIMO 802.11a/n/ac/ax; max 20dBm per chain; up to 1201 Mbps |
| Frequency Ranges | 2.4GHz: 2.412 ~ 2.472GHz5GHz: 5.150 ~ 5.825GHz |
| Modulation | OFDMA: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM |
| Antenna Connectors | 4× U.FL connectors (2 per band) |
Notes & Recommendations
- Always connect appropriate antennas to all 4 U.FL ports before powering on. Never operate with open (unterminated) U.FL connectors, as this may damage the RF front-end.
- Use antennas rated for the specific frequency band (2.4GHz or 5GHz) and ensure 50Ω impedance matching.
- Do not modify the onboard antenna circuitry or U.FL connector wiring. Unauthorised modifications will void regulatory compliance.
Mechanical Specifications
Board Dimensions
| Dimensions (W × H × D) | 128mm × 210mm × 33.9mm (with heatsink) |
| PCB Thickness | Standard (multi-layer PCB) |
Environmental Ratings
| Operating Temperature | -20°C to 70°C |
| Storage Temperature | -40°C to 90°C |
| Operating Humidity | 5% to 95%, Non-Condensing |
| Storage Humidity | Max. 90%, Non-Condensing |
| Certification | REACH & RoHS Compliant |
Mounting & Installation Notes
- Allow sufficient clearance around the board for airflow and RF signal propagation. The WPQ618 board includes mounting holes at the corners for secure mechanical integration into an enclosure or chassis.
- Ensure adequate clearance around all connectors (RJ45, USB, U.FL, DC Jack) for cable routing.
- Provide sufficient airflow or thermal management for the SoC and on-board radio components, particularly in high-throughput applications.
- Do not stack objects directly on the board surface. Ensure the PCB is mounted horizontally or secured in a suitable bracket.
- All dimensions are in millimetres. Refer to the mechanical drawing on the datasheet for precise mounting hole locations.
Power Requirements
| Dimensions (W × H × D) | 128mm × 210mm × 33.9mm (with heatsink) |
| PCB Thickness | Standard (multi-layer PCB) |
Environmental Ratings
| Operating Voltage | 12 V DC (via DC Jack Connector) or PoE 48~56V (IEEE 802.3at, via 2.5Gbps LAN port) |
| Power Consumption | 17.5W (max, board only, including Bluetooth) |
Operating Voltage
12 V DC (via DC Jack Connector) or PoE 48~56V (IEEE 802.3at, via 2.5Gbps LAN port)
Power Consumption
- 17.5W (max, board only, including Bluetooth)
- Ensure the external power supply is rated to deliver at least 17.5W at 12V DC continuously, or a compliant PoE source if using PoE input.
- Use a regulated DC power supply. Unregulated or noisy supplies may adversely affect RF performance.
Notes & Recommendations
- Disconnect power before installing any external cables or performing maintenance.
- Never exceed 12 V DC input. Overvoltage will permanently damage the board.
- Verify power supply polarity before connecting. Reverse polarity damage may not be covered under warranty.
- Do not connect DC and PoE power simultaneously unless confirmed safe by the power arbitration circuitry.
- Account for the full 17.5W maximum power draw when sizing the power supply for enclosure designs.
Installation & Integration
Pre-Installation Checklist
- Verify package contents (see Section 2) before starting installation.
- Prepare a 12V DC, 17.5W regulated power supply (or a compliant PoE source).
- Prepare external antennas for all 4 U.FL connectors (2 per band: 2.4GHz, 5GHz).
- Prepare Ethernet cables (Cat5e or higher) for LAN/WAN connections.
- If using the M.2 (NGFF) slots, prepare the intended 5G modem/companion module and SIM cards in advance.
- Ensure an ESD-safe work environment before handling the board (see Section 10).
- Have a laptop or PC available for initial configuration via Ethernet.
Antenna Connection
The WPQ618 provides 4 U.FL antenna connectors for on-board Wi-Fi (2 per band). All antenna connectors in use must be fitted before powering on the board.
- Identify the correct U.FL connectors for each band using the Component Map (Section 3.2).
- Press each U.FL connector cable firmly until a tactile click is felt, confirming full engagement.
- Ensure antenna cables are not sharply bent or kinked, as this degrades RF performance.
M.2 Module & SIM Card Installation (Optional)
- Power off and disconnect the board before installing or removing an M.2 module or SIM card.
- Insert the M.2 module into the appropriate B Key slot at an angle, then press down firmly and secure with the mounting screw.
- Insert SIM cards into the SIM card slots corresponding to the installed cellular modem, observing correct orientation.
- Confirm module compatibility (PCIe 3.0 for the 5G modem slot; USB 3.0 for the companion module slot) before installation.
Power Connection
Connect the 12V DC power supply to the DC Jack connector on the board, or alternatively connect a PoE-compliant Ethernet cable (IEEE 802.3at) to the 2.5Gbps LAN port.
- Verify the power supply is rated at 12V DC, 17.5W (minimum).
- Insert the DC Jack plug firmly into the board’s DC Jack socket.
- Power on the supply and confirm the LED array responds.
- Allow the board sufficient time to complete its boot sequence before testing connectivity.
Ethernet Connection
- Connect a PC or network device to any of the 1Gbps LAN/WAN ports or the 2.5Gbps LAN port as required by the application.
- Ensure Ethernet cables are Cat5e or higher for 1Gbps connections, and Cat6 or higher for 2.5Gbps connections.
- Both Ethernet ports support auto-MDI/MDIX, so straight-through or crossover cables may be used.
Configuration
The WPQ618 runs the CompexWRT firmware stack and can be configured via the webUI or through the SSH/serial console command line.
Default Settings
| Default Management IP | 192.168.1.1 |
| Default Subnet | 192.168.1.0/24 |
| Web UI Port | 80 (HTTP) / 443 (HTTPS) |
| Default Username | admin |
| Default Password | password |
| SSH Access | Port 22 (enabled by default) |
| Default Mode | Access Point |
| Serial Console | 115200 bps, 8N1 |
Accessing the Web Interface
- Connect a PC to one of the WPQ618’s Ethernet ports.
- Set the host PC’s Ethernet adapter to a static IP address in the 192.168.1.x range (e.g. 192.168.1.10, subnet 255.255.255.0).
- Open a web browser and navigate to http://192.168.1.1 (default IP Address).
- Log in with username admin and the password password. If no password has been set, the browser will prompt you to create one.
- The webUI management interface will load, providing access to network, wireless, cellular, and system configuration.
Wireless Configuration
Wireless settings can be configured via the webUI, or via SSH/serial console using UCI commands or by directly editing the configuration files.
- Via webUI: Navigate to Network > Wireless to configure SSID, security, channel, and bandwidth settings for both 2.4 GHz and 5 GHz radios.
- Via SSH: Connect using PuTTY or any SSH client to 192.168.1.1 on port 22.
- Via Serial Console: Connect using TeraTerm or similar terminal software with the Serial 4- pin connector (115200 bps, 8N1) and a TTL serial converter.
- Wireless configuration files are located at /etc/config/wireless.
- Use UCI commands to modify settings, e.g.: uci set wireless.wifi0.disabled=’0′ uci set wireless.wifi0.htmode=’EHT40′ uci commit wireless wifi
- wifi0 typically corresponds to the 2.4GHz radio and wifi1 to the 5GHz radio; confirm the exact radio-to-band mapping for your board using iw dev before applying changes.
- Use iw dev to verify radio status after applying changes.
- Refer to the CompexWRT documentation supplied by Compex for the full set of UCI options and configuration file locations.
Troubleshooting
| Power LED not lit | Check 12V DC power supply voltage and polarity. Verify DC jack connection is secure. Confirm supply provides at least 17.5W continuous power. |
| Ethernet link not established | Verify Ethernet cable is fully seated in RJ45 port. Confirm link partner supports the relevant speed (1G or 2.5G). Try a different cable or port. |
| Cannot access webUI | Confirm host PC IP is set to 192.168.1.x/24. Disable any VPNs or firewall rules blocking 192.168.1.1. Verify Ethernet link LED is active. |
| Wi-Fi SSIDs not visible | Confirm all 4 U.FL antenna connectors in use are properly attached. Allow the board sufficient boot time. Refer to CompexWRT documentation to verify radio settings are enabled. |
| Poor Wi-Fi throughput | Verify antenna orientation and placement. Ensure correct channel and bandwidth settings. Check for RF interference sources nearby. |
| Bluetooth not detected | Confirm the on-board Bluetooth module is enabled in the firmware configuration. Verify no physical damage to the Bluetooth module. |
| Board overheating | Ensure adequate airflow clearance around the SoC and radio components. Verify ambient temperature is within operating range (-20 to 70°C). |
| Firmware upgrade fails | Do not power off during update. Use a wired Ethernet connection for firmware upload. Reset to factory defaults before upgrading if previously customised. |
| M.2 module / 5G modem not detected | Ensure the module is correctly seated in the M.2 slot and secured with the mounting screw. Verify the module is supported by the installed CompexWRT firmware version. If using a 5G modem, confirm the SIM card is correctly inserted. |
| Factory Reset | To restore factory default settings:• Press and hold the RESET button for 10 seconds while the board is powered on.• Go to webUI > System > Reset Board.• Alternatively, via SSH or serial console, run:rm -rf /overlay/* rebootThe board will reboot and restore all settings to factory defaults. This process takes approximately 60 seconds. |
Safety Precautions
Electrical Safety
- Disconnect power before connecting or disconnecting any cables or performing anymaintenance.
- Never exceed the rated input voltage (12 V DC). Overvoltage will permanently damagethe board.
- Verify power supply polarity before connecting. Reverse polarity damage is not coveredunder warranty.
- Keep the board away from conductive materials that may cause short circuits.
RF / Antenna Safety
- Never operate Wi-Fi radios or the 5G modem without antennas or 50 Ω termination loadson all U.FL ports.
- Do not modify antennas or RF circuitry. Unauthorised modifications will void regulatorycompliance.
Thermal Safety
- Operating the board above 70°C ambient temperature may cause thermal shutdown orpermanent damage. Ensure adequate cooling is installed.
- Do not obstruct ventilation around the board.
- Allow the board to cool down before handling after extended operation.
ESD Precautions
- Handle the board only at a properly grounded ESD workstation.
- Wear an ESD wrist strap connected to ground at all times when handling the board.
- Store the board in its original ESD protective bag when not in use.
- Avoid touching PCB traces, IC pads, or connector pins directly.
Technical Support
Compex Systems Pte Ltd provides engineering and technical support for the WPQ618. For technical assistance, integration support, or to report a hardware issue, please contact:
| Company | Compex Systems Pte Ltd |
| Headquarters | Singapore |
| Sales Enquiries | sales@compex.com.sg |
| Technical Support | https://compex.com.sg/support-downloads/ |
| Website | https://compex.com.sg |
| Product Page (WPQ618) | https://compex.com.sg/shop/embedded-board/802-11ax/wpq618/ |
| Qualcomm Design Centre | Qualcomm Authorized Design Centre (ADC) since 2014 |
Before contacting support, please:
- Note the firmware version (visible via webUI: System > Software, or via SSH/serial console: cat /etc/openwrt_release)
- Record the MAC address of the board (visible on PCB label).
- Describe the issue with steps to reproduce, observed symptoms, and host platform details.
For sample requests, pre-production evaluations, or OEM/ODM partnership enquiries, contact the Compex sales team at sales@compex.com.sg
Regulatory Information
Declaration of Conformity
The WPQ618 is designed to comply with applicable regional regulatory requirements. End-product manufacturers are responsible for obtaining all necessary regulatory certifications (e.g., FCC, CE, IMDA) for their final product in each target market. The WPQ618 is provided as an embedded board for OEM/ODM integration and does not carry end-product regulatory approval.
REACH & RoHS Compliance
This product is manufactured in compliance with REACH Regulation (EC) No 1907/2006 and RoHS Directive 2011/65/EU (amended by 2015/863/EU), restricting the use of hazardous substances in electrical and electronic equipment.
Disposal & Recycling
Do not dispose of this product in unsorted municipal waste. This product is subject to the Waste Electrical and Electronic Equipment (WEEE) Directive. Return it to an authorised recycling facility or contact Compex Systems for take-back options.
Legal Notices
Qualcomm and IPQ6018 are trademarks or registered trademarks of Qualcomm Technologies, Inc. Compex® and the Compex logo are trademarks of Compex Systems Pte Ltd. All other trademarks are the property of their respective owners.
Copyright
© 2026 Compex Systems Pte Ltd. All rights reserved.
Documents / Resources
![]() | WPQ618 Hardware |

