Viotel Limited Version 2.1 V21 Accelerometer Node User Manual

Viotel Limited Version 2.1 V21 Accelerometer Node

OVERVIEW

The Viotel Accelerometer Node is a low-touch IoT device designed to be installed and activated with minimal user effort. It monitors for events, can upload data over integrated LTE/CAT-M1 cellular communications, and uses GPS for time synchronisation when comparing events between nodes.

Specifications

Quick Setup & Use

1. Mount the node using one of the supported options: two-sided adhesive (clean/dry surface, press and hold ~20 minutes), threaded M3 holes, or side mounting holes for M5 countersunk bolts/screws.
2. If using an external antenna option, ensure both antennas are plugged in before operation.
3. Activate with the magnet: By default, the node is Off. Hold the magnet at the spot located directly behind the “O” on the Viotel logo. Release at that position to send the specified command.
4. Switch states (On/Off): Hold the magnet for 4 seconds to switch On/Off. When On, the device records data per the selected mode and checks for triggers and magnet inputs; when Off, it checks for wake-up commands (e.g., magnet) and initiates a connection every 7 days for status updates and system update checks.
5. Use the STATUS LED feedback: At each function, the STATUS LED lights once and indicates the current status.

Introduction

Warning

• This guide intends to assist in the preferred mounting, operation, and usage of Viotel’s Accelerometer Node.
• Please read and completely understand this user guide in order to make sure the safe and correct use of the system, as well as to maintain the longevity of the node.
• Protection provided by the equipment may be impaired if used in a manner contrary to this user manual.
• Changes or modifications not expressly approved by Viotel Limited could void the user’s authority to operate the equipment.
• If the external antenna option is selected, both antennas must be plugged in before any operation occurs.
• This product must not be disposed of in the normal waste stream. It contains a battery pack and electronic components, and so should be recycled appropriately.

Theory of Operation

• The Accelerometer is a low-touch Internet of Things (IoT) device. It is designed to be as simple as possible to install and activate — set and forget. Data is retrieved from the device via our cloud-based platform, or via API to yours, using the integrated
• LTE/CAT-M1 cellular communications. The device also uses GPS for time synchronisation where comparison of events between nodes is required.
• The device sensor is always monitoring for events and can be continuously monitored or set to a triggered state. Remote configuration is possible to change the acquisition and upload frequency.

Parts List

• The Viotel Accelerometer has optional additions including external antennas, external power, and mounting kits. Please contact sales@viotel.co before ordering.

Table 1 Parts list

Required Tools

• Tools are not required for installation other than hand tools specific to your installation scenario. The following tools may be required for changing the batteries.
• T10 Torx screwdriver
• Thin needle-nose pliers

Dimensions

Usage

Mounting Options

• Viotel’s Accelerometer Node comes with three primary mounting options. It is recommended that a combination of two is used for optimal results.

Table 2: Mounting options

Orientation and Magnet Location

The switch that the magnet (Part 4) operates on the Accelerometer (Part 1) is located directly behind the “O” on the Viotel logo.

Operating Instructions

Operation

• By default, your Viotel Accelerometer Node will be set to Off. Wherever instructed to hold the magnet in place, do so at the spot indicated in section 2.2 Orientation and Magnet Location. Releasing from this position will send through the specified command.
• At each function, the STATUS LED will light once, in the colour representing its current status.
• All operations and LED indications refer to firmware version 3.02.14. Please be aware that future firmware versions may change some functionality. The current firmware version for your device is shown in myViotel.

Table 3 How to switch between states

Modes

Table 4 Description of device modes

System Status Indicator

Table 5 System status indicator

System Communications Indicator

Table 6 System communications indicator

Maintenance

• The product should not require any maintenance after installation. If the need to clean the product should arise, use only a damp cloth and mild detergent. Do not use any solvents, as these may damage the enclosure.
• Only service personnel authorised by the manufacturer may open the inner enclosure. No user-serviceable parts are located inside.

Changing Batteries

Table 7 Changing the battery

External Power

• A 5.0–7.5 V DC (1 A max) supply is required to power your device. All electrical work must be carried out by a suitably qualified technician, and in compliance with local laws and regulations.
• The installer must listen for a ‘click’ to confirm that the connector is securely sealed.
• 7-pin connectors and power adaptors can be purchased from Viotel. See Products and Data Loggers at: www.viotel.co/products/all.

Downloading Data

• The only way to retrieve data is over the cellular communications network. This can be activated on demand using the magnet. However, if the device is in the field and is unable to upload data, the device is programmed to keep trying in decreasing increments.
• If after 4 days of attempting to upload it has not succeeded, it will reboot.
• Data loss may occur during extended power-loss periods.
• Data is deleted from the device once successfully uploaded.

Further Support

• For further support, please email our team at support@viotel.co with your name and number, and we will get back to you.
• Sales enquiries: sales@viotel.co · +64 9 302 0621
• Viotel Limited
• Auckland
• Suite 1.2, 89 Grafton Road
• Parnell, Auckland 1010, New Zealand
• Company number 7540596 · NZBN 94 2904 7516 083
• Viotel Australia Pty Ltd
• Hobart
• Tenancy 4, 30 Patrick Street
• Hobart TAS 7000, Australia
• Sydney
• Suite 3.17, 32 Delhi Road
• Macquarie Park NSW 2113, Australia
• ACN 645 231 349 · ABN 34 645 231 349
• Remote offices: Brisbane
• Sales enquiries: sales@viotel.co
• Technical support: support@viotel.co
• +64 9 302 0621 · www.viotel.co
• Australian made, New Zealand owned

Troubleshooting

• External antenna selected, device won’t operate as expected: Confirm that both antennas are plugged in before any operation occurs.
• STATUS LED indicates the device is busy / won’t accept commands: The system status indicator shows solid red (300 ms), meaning the device is currently busy and will not accept magnet commands. Wait until the device completes its current activity.
• No device action or command confirmation not received: Use the system status indicator Purple blink, which indicates the device has confirmed the command from the magnet.
• GPS not available: The communications indicator shows solid red (1s intervals) when GPS fixing fails to get a valid position, or solid yellow once a valid position is obtained.
• Device cannot report data: If the communications indicator shows solid red for 2s, meaning the device has stopped communicating after failing to report any data, check connectivity conditions and allow time for communications recovery.
• Firmware update in progress: If green/red blink alternating is shown, a firmware update is underway; commands may not be accepted while busy.