sylvan SL42E Smart Lock Installation Guide

sylvan SL42E Smart Lock

sylvan SL42E Smart Lock

Introduction

Thank you for choosing Sylvan, this lock is for Residential use only, and its two year warranty (mechanical and electronic) only applies for locks being used for residential use.

To ensure you get the best out of your purchase we ask that you follow the below:

  • Please read these instructions fully before installation of this lock.
  • We recommend this lock is installed by a professional installer or a serious DIYer to ensure correct installation and operation.
  • The supplied rubber boots must be installed; however, this smart lock requires a smooth flat surface to hold its water tightness. This lock is not suitable for use on a tongue and groove door, where water can penetrate the lock via a groove in the door.
  • We recommend that this lock is never fully exposed to direct weather for long periods of time. For long lasting properties of the product, positioning the lock under a eve or sheltered position is best.
  • This lock is rated IP55, but only on the outward face of the lock. No warranty is given if the lock gets damaged from water for the inside of the door.
  • This lock is not suitable for use on a gate.
  • This lock comes with a mechanical key override, this can be used in a situation of complete battery loss. We recommend an override key is put somewhere safe outside in case complete power loss.
  • Replace batteries when they are showing low voltage on the app.
  • All batteries used with this lock must be high quality Alkaline (4 x AA batteries), to ensure long lasting use.
  • Lithium or rechargeable batteries cannot be used with this lock.
    Symbol

Installation Video
Scan this code:
QR Code

App Setup Video
Scan this code:
QR Code

If you prefer not using an app for programming your smart lock, most functions can be setup manually using the instructions here:
QR Code

Lock Dimensions

Lock Dimensions

SL42E Packing List

  • Front panel
    Qty x1
    SL42E Packing List
  • Back panel
    Qty x1
    SL42E Packing List
  • User manual
    Qty x1
    SL42E Packing List
  • Installation template
    Qty x1
    SL42E Packing List
  • Mortice lock / latch
    Qty x1
    SL42E Packing List
  • Striker plate
    Qty x1
    SL42E Packing List
  • RFID Tag
    Qty x2
    SL42E Packing List
  • Self adhesive disc
    Qty x2
    SL42E Packing List
  • Mechanical keys
    Qty x 2
    SL42E Packing List
  • Waterproof rubber boot
    Qty x2
    SL42E Packing List
  • Striker Plate Box
    Qty x1
    SL42E Packing List
  • PM3*8 Roundheaded
    screw
    SL42E Packing List
  • Mortice screws
    Qty x4 M5x10mm (For Aluminum doors) Qty x4 M4x20mm (For Wooden doors)
    SL42E Packing List
  • Connection posts
    Qty x2
    (M5x30 + M5x40)
    SL42E Packing List
  • Various M5 machine screws
    x2 11mm
    x1 25mm
    x1 30mm
    SL42E Packing List
  • Various M6 machine screws
    x2 55mm
    x2 65mm
    SL42E Packing List
  • Smart hub
    Qty x1 (optional)
    SL42E Packing List
  • Magnet Sensor
    Qty x1
    SL42E Packing List

Product specifications

Model number SL42E Door thickness range 35mm – 60mm
Material of Manufacture Aluminum alloy
Weight 1.3 kg Type of use Residential use only
Options of unlocking Bluetooth Password Card Mechanical key Passcode capacity App unlocks Passcodes: 150 max RFID Cards: 200 max
Working temperature -10 – + 55 degrees C Working Humidity 0-95%
Normal voltage 6 volts (4 x Alkaline batteries) Warranty 2 years mechanical
2 years electronic
Low voltage Alarm Less than 4.8 Volts Lock Stainless steel body

Note: We do not recommend using rechargeable or lithium batteries as damage caused will void the warranty Only use high quality alkaline batteries, suitable for high drain devices such as Energizer Max Plus

Anti Peeping Technology
This lock offers anti-peeping virtual passcode entry by inputting a random passcode either before or after the proper passcode followed by the # key

Installation

Step 1: Install Mortise

  1. Mark and crop door using installation template provided
  2. Ensure holes are clear of any sharp edges and clean of swarf and wood dust.
  3. Install the mortise into the door with screws
  4. and keep the deadbolt in retracted position
    Installation

Step 2: Install Exterior Assembly

  1. Install the sliding screw stubs to the front panel.
  2. Install the waterproof rubber plate to exterior assembly.
  3. Keep the cylinder rod horizontal when installing.
  4. Install the exterior assembly to the door.
  5. Depending on door thickness, the spindle may need to be shortened by using a hacksaw to reduce the spindle length.
    Installation
    Installation
    Incorrect spindle length will cause damage to the lock overtime and may void warranty due to incorrect installation.

Step 3 Install Interior Assembly

  1. Install the waterproof rubber plate to fixing plate.
  2. Fix the fixing plate and exterior assembly with screws.
  3. Connect the wire,Install the interior assembly on the fixing plate with screws. Symbol IMPORTANT Plug in power cable ensuring the plug is around the correct way for the plug to accept its receiver correctly.
  4. Install the battery and battery cover to complete the installation.
    Installation
    Installation

Position the door sensor (Optional)
By positioning the sensor on the interior door frame close to the lock body, you can set the lock to throw the bolt only when the door is closed.
Installation

SL42E Installation Instructions

Lock Installation Checklist

  1. Holes drilled and aligned as per drilling template.
  2. Ensure the rubber boot is aligned correctly with a good seal on the door, also making sure the lugs are correctly seated in their holes .
  3. Ensure all screws and bolts are correctly tightened.
  4. Ensure power cable is installed and not bent or crimped in door.
  5. Check batteries are Alkaline and installed correctly.
  6. Check to see if the lock requires a software update via the TT App
    Symbol

Manual reset:
If you are not admin of the Smart Lock, remove battery cover and complete:
Long press the reset button beneath the battery case for 5 seconds or until you hear: “Please Input Initialisation Passcode”.
Now input code “000✔” on the keypad.
The system reset will be complete. From here you can re-link the SL42E Smart Lock to your phone via the TT App.
Note: this will clear all previous users from the locks memory.
Lock Installation Checklist

Using your Sylvan SL42E Smart Lock

The SL42E Smart Lock has a mechanical key override to unlock it.
The key location is on the front panel.
Insert one of the included keys, turn to unlock.

Maintenance Guide: 

Maintenance should be carried out on your lock every 6 months:

  • Check that the screws fixing the mortice Lock are tight.
    Check that the screws fixing the rear panel to the front panel are tight.
  • Check if batteries need replacing. If battery percentage is low replace with four fresh Alkaline 1.5V AA batteries.
  • Wipe the surface of the Lock with a damp cloth, we recommend only water is used. This will help remove any dust or micro contaminants from the surface.
  • It is also recommended to do a full factory reset of the Smart Lock to ensure software runs correctly.
  • Check rubber boot to ensure the seal between lock and door is still good.

Maintenance Guide

Sylvan Smart App Set-up instructions

  1. Download the Sylvan Smart App
    Apple (IOS version) use app store to download Sylvan Smart
    Android version go through Google Play to download Sylvan Smart
    Or alternatively scan the QR Code below
    QR Code
    App Store Google Play

    Sylvan Smart App Set-up instructions

Sylvan Smart App

  • Sylvan Smart supports multiple types of locks and devices
  • Verification codes will be sent to users’ mobile phone or email depending on how you have registered above.

Management of app and lock

Symbol Account setup and add locks

  1. Register a new account (phone number or email) OR if you have an existing account login using your current account details
    Management of app and lock
  2. With App open touch on home screen select + / Add lock
    Management of app and lock
  3. While standing near the lock (and with the 4 good quality AA alkaline batteries installed into the lock) wake the lock up by touching the keypad.
    Management of app and lock
  4. Your lock will appear on the screen, then select +
    Management of app and lock
  5. Rename the lock. e.g. home front door
    Management of app and lock
  6. The lock is now successfully added to the Sylvan Smart app.
    Management of app and lock
  7. If you have downloaded the app and loaded your lock on your device you are now the administrator of this lock, from here you can now add or delete users / passcodes / RFID card etc.

Symbol Bluetooth (lock and unlock)

  1. Make sure your phone has Bluetooth and Bluetooth is switched on.
  2. The app can be used to lock or unlock the door by using Bluetooth within a 5m range.
  3. From the app press the (padlock) symbol to lock or unlock the device.
    Management of app and lock

NOTE

  • The lock will automatically re lock itself depending on the setup of the auto lock function through the app.
  • 5-meter Bluetooth range can vary depending on interference such as steel, thick walls and microwave interference etc.

Symbol RFID cards

This lock comes with three RFID cards and can store up to 200 unique RFID cards.

  1. To add these to the lock, select Cards
    Management of app and lock
  2. Add card
    Management of app and lock
  3. Select Permanent, Timed or Recurring user
  4. Name the Card (we suggest the users name) e.g. Bobs RFID, press ok.
  5. Then touch card against lock keypad to accept card to lock
    Management of app and lock

Symbol Setting a passcode:

  1. Open the Sylvan Smart App
  2. Select your lock
  3. Press Passcodes
    Management of app and lock
  4. Generate Passcode
    Management of app and lock
  5. As suggested in the notes below Press “custom”
  6. Ensure Permanent is switched for all time access
  7. Enter a name for the passcode eg Bob’s code
  8. Enter the 4–9-digit passcode then # or ✔ depending on the model (refer above)
  9. Press Set passcode
    Management of app and lock

Helpful hints when setting up passcodes:

  • Careful consideration should be taken to ensure each PIN is set up in a way that they can be managed later. We suggest naming each PIN with the name of the person using it. E.g. Bobs PIN
  • When setting up passcodes use the ‘custom’ setting to create your own pin number. It needs to be between 4-9 digits followed by ‘#’ or ✔ e.g. 1234#.
  • Recurring PIN codes are used to give access to the user of this code at certain times of the day and week.
  • Codes can also be created for “One time” access (for example a tradesperson working in your house for a short period of time).

Symbol Fingerprint Access: (only applicable if your lock has this feature)

This lock can accept up to 200 Unique fingerprints

  1. From your locks main screen select Fingerprints
    Management of app and lock
  2. Then add fingerprint
    Management of app and lock
  3. Decide if a Permanent, Timed or Recurring user
  4. Name the fingerprint (we suggest the users name) eg Bobs Finger
    Management of app and lock
  5. The app then prompts you to present your finger or thumb to the reader.
    Management of app and lock
  6. Watch and listen to the prompt of the app and lock you will see the image of the fingerprint and be asked to present your finger to the reader.
  7. You will be asked to do this several times until all parts of the image on the app turn from black to orange.
    Management of app and lock

Note:
We suggest for convenience and user speed to save your fingerprint in several different positions. EG Bobs 1 finger, Bobs 2 finger etc.

Passage mode

The Sylvan Smart app can be used to put the lock into passage mode.
Note: Passage mode is where the lock can be opened without requiring the passcode to be entered.

  1. Under the setting tab of the lock, you can switch passage mode on or off
  2. You can also set up a calendar so that the lock can go into passage mode on certain days at certain times.
  3. Note for security reasons the passage mode only starts once a successful entry to unlock the lock has been accepted.
    To lock the door when in passage mode, press and hold the # key on the lock.
    Management of app and lock

Scheduled Passage Mode

Scheduled Passage Mode keeps the lock unlocked during the times you specify.

  • Go to Settings > Passage Mode.
    Management of app and lock
  • Choose the days and hours you want the lock to remain open, for example Monday to Friday, 9:00 to 17:00.
    Management of app and lock
  • When unlocked electronically during these hours, the lock will remain in the unlocked state.
  • If Auto Lock is enabled, the lock will secure itself again at the scheduled time.
    Management of app and lock

Enable Manual Passage Mode

You can enable Passage Mode manually by unlocking the Sylvan Smart using a PIN or another valid method, then entering 123# or ✔ on the keypad.

Lock the Door While in Passage Mode

  • Option 1: Open the Sylvan Smart App, then press and hold the Lock button. Lift the handle to engage the deadbolt.
  • Option 2: To exit Passage Mode from the keypad, press and hold the # or ✔ key, then lift the handle to engage the bolt.
    Management of app and lock

Privacy mode

Some Sylvan locks have a secure lock function (SL37, SL39) the button is underneath (SL38, SL40, SL41) the button is on the back face of the lock.
When the secure lock feature is turned on (Red is showing on the SL38/SL40/ SL41) only the key override or master admin code can be used to unlock the lock.
If this function is turned off (showing Green) the lock is in normal mode.
Privacy mode

  1. Under the setting tab of the lock, you can switch privacy mode on or off, By switching the turn off feature, this will disable the button on your lock.
    Privacy mode

Symbol Remote unlock

This can be done using a smart hub SLG02 (sold separately) see ‘www.sylvan.co.nz/smart-hub-slg02’

  1. Add the smart hub via the home screen of the app
  2. Ensure the gateway is within 10 meters of the lock and unplugged
  3. Click on + / add new device
    Remote unlock
  4. Choose the G2 (Wi-Fi) option under Gateway
    Remote unlock
  5. Connect power to the gateway and the indicator light will flash red, it’s now in programming mode
  6. Click next
    Remote unlock
  7. Your gateway will appear on the screen, then select +
    Remote unlock
  8. Configure network:
    The app will ask you to select your WiFi network and password (Important this needs to be a 2.4G) signal. 5G is not supported.
    Ensure your smart phone is connected to the 2.4G signal whilst connecting to the gateway
    Once seen it will ask for you to name the gateway e.g.
    (garage door gate way) Once complete, select OK
    Remote unlock
  9. The gateway is now connected.
    Remote unlock
  10. Check that the gateway is online under the gateway link on the front page of the App
    Remote unlock
  11. Return to the setting screen of your lock and click on gateway and you should see your named gateway.
    Remote unlock
  12. On the settings page select ‘Turn on Remote Lock’.
    Remote unlock
  13. On the main programming screen of the lock a small WiFi/Padlock symbol will now appear next to the padlock symbol of the app.
    Remote unlock
  14. By clicking on the WiFi/ Padlock symbol, then clicking Remote unlock you will be able to remotely unlock your lock from anywhere using the secure Wi Fi connection.
    Remote unlock
  15. The app will show when the lock has been successfully unlocked.
    Remote unlock

Additional Settings

Power and Time Settings

Check Battery Percentage

Use the Sylvan Smart App to check the battery level of your Sylvan Smart lock.

  • On the lock selection page, the app shows an overview rounded to the nearest 5%.
  • For a more precise reading, go to Settings > Basics.
  • To refresh the reading, select Battery and then Update while you are within Bluetooth range of the lock.
    Additional Settings

Calibrate the Lockset Clock

  • Open Settings > Lock Clock.
  • Select Calibrate Time.
  • Your Sylvan Smart lock will sync with the app and set the correct time.
  • This helps keep operating schedules and unlock records accurate.
    Additional Settings

Authorised Admin

An Authorised Admin can access your Sylvan Smart using their own Sylvan Smart App.

  • They can add, change, or delete unlock codes that they create themselves.
  • To set this up, go to Authorised Admin on the lock management home page, then select Create Admin.
  • Send the invitation to the phone number or email address linked to the recipient’s Sylvan Smart App account.
    Access and User Management

e-Key Management

An e-Key allows another person to lock or unlock your Sylvan Smart lock through the Sylvan Smart App.

  • e-Keys can be permanent or set with specic time or access parameters.
  • On the lock management page, select e Keys, then choose Send e Key.
  • Send the e-Key to the phone number or email address linked to the recipient’s Sylvan Smart App account.
    Access and User Management

Transfer Ownership

The Master Admin can transfer ownership of a lock to another Sylvan Smart App account holder, including saved settings and PINs.

  • Open the app menu, then go to Settings > Transfer Lock.
  • Select the lock you want to transfer.
  • Enter the recipient’s phone number or email address associated with their Sylvan Smart App account, then select Next.
    Access and User Management

Security and Access Records 

Admin Passcode
Each Sylvan Smart lock comes with an admin passcode.

  • To view it, go to Settings on the lock management page, then select Basics > Admin Passcode.
    Additional Settings

Unlock Records

The Sylvan Smart App records which passcodes were used to lock or unlock the Sylvan Smart and when they were used.

  • To view these records, open the Records menu on the lock management page.
  • Only a limited period of records can be stored in the app.
  • You can export records to a spreadsheet for long-term storage, then clear or refresh the app records to keep them current.
    Additional Settings

Lock Behaviour and Sound

Auto Lock

Auto Lock automatically disengages the exterior handle after a set period.

  • In the app, go to Settings > Auto Lock.
  • Adjust the timer or turn the feature off as needed.
  • If Auto Lock is turned off, Passage Mode will not relock automatically.
    Lock Behaviour and Sound

Lock Sound

Use Lock Sound to enable or disable audio feedback and to control the volume.

  • By default, Lock Sound is enabled and set to high.
  • Go to Settings > Lock Sound to change the setting.
    Lock Sound

Lock Sync and Grouping

Import from Another Lock
This feature lets you sync PIN codes and RFID cards between Sylvan Smart locks.

  • Go to Settings > Import from another lock.
  • Select the lock you want to import from.
    Lock Sync and Grouping

Lock Groups
Lock Groups let you organise multiple Sylvan Smart locks together, such as locks at the same site.

  • First create a lock group in the main settings.
  • Then, in each individual lock, go to Settings > Basics > Lock Group and assign the lock to the group.
  • You can view lock groups from the lock selection page to keep the app home screen tidy.
    Lock Groups

Reset Button Control
You can disable the manual reset button by turning off Reset Button in the Sylvan Smart App settings.

  • Go to Settings > Reset Button and adjust the setting to suit your needs.
  • This can be especially useful for Airbnb properties, rentals, or other shared-use installations.
  • When the reset button is disabled, only the Master Admin can factory reset the lock
    Reset Button Control

Factory Reset

  • Via the Sylvan Smart App (Master Admin only): On the lock management page and within Bluetooth range, go to Settings > Delete, then enter your app password. The lock will then be factory reset.
  • Manual reset: Remove the battery cover and hold the reset button in the battery compartment until you hear, “Please input initialization passcode.” Enter 000# on the keypad. The lock will then announce, “Deleting administrator successful.”
  • If the Reset Button feature has been disabled, manual reset will not be available.
    Factory Reset

Remove Reset or Replaced Locks from the App

  • To remove a reset or replaced lock from the Sylvan Smart App, open the app menu and go to Settings. Select Transfer Lock(s), choose the lock, select Next, then choose Remove the damaged device at the bottom of the page.
    Remove Reset or Replaced Locks from the App

Autolocking feature

The SL42E smart lock includes an auto-locking feature, this eliminates the risk of damaging the lock and door frame by not allowing the bolt to engage before the door is closed.

  1. Adjust the door sensor
    • Loosen the screws on the rear panel, and then push the door sensor towards the door frame to ensure that the door sensor and the magnet are within the sensing distance.
    • Door timing delay can be adjusted through the app under Auto lock.
      A great way to ensure the bolt is thrown only when the door is closed is to do the flowing:
  2. Frame sensor auto lock: In the Sylvan Smart app, once the deadbolt has been set up correctly and passcodes have been entered, ensure the deadbolt has the auto-lock function switched off under Settings / Autolock.
  3. Position the frame magnet on the frame close to the deadbolt sensor (depending on if the sensor and frame magnet are sitting directly in line with each other, the gap can be up to 30mm)
  4. When the door closes, the sensor will recognise that it’s close to the frame magnet and automatically lock the deadbolt.
  5. Once happy with the operation, lock the sensor screw down in the battery compartment and double-sided tape the frame sensor permanently down
    Autolocking feature
    Autolocking feature

Autolocking feature

Note:

  1. Please keep this card so that you can use it when you need warranty service.
  2. We provide you with a two-year warranty from the date of purchase.

Customer Support

Logo

127 Diana Drive
Glenfield
Auckland 0627
Ph: +64 9 444 5359
Email: sales@gdrutter.co.nz
Web: www.sylvan.co.nz

Download the Sylvan Smart App Scan the QR Code to get started!
QR Code

Symbol

Logo

Documents / Resources

PDF thumbnailSL42E Smart Lock
Installation Guide · SL42E, smart lock, door lock, SL42E Smart Lock, Smart Lock

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.