Voltrover Handlebars LCD Display Installation Guide

Voltrover-logo

Voltrover Handlebars LCD Display

Voltrover-Handlebars-LCD-Display-product

Installation

How to Install Handlebars

  1. ecure the Handlebar
    Align it with the mounting holes, and tighten the screws with a tool
  2. Mount the Handlebar
    Align the tool with the screw holes and turn it to tighten the screws
  3. Mount the Handbrake
    Align its mounting holes with those on the handlebar, first secure it by hand, then turn the tool to tighten the screws.

Voltrover-Handlebars-LCD-Display- (2)

How to Tell if a Charger Is Working Properly

Green Light
The green light indicates two scenarios

  1. Fully charged (the light will naturally turn green after the battery is fully charged continuously)
  2.  Unable to charge the battery

Reasons for the battery not charging:

  1. Issue with the charger (the charger displays a green light)
  2. Connection problem between the charging port and the cable (the charger also shows a green light)
  3.  Issue with the battery itself

Red Light
A red light on the charger means it is operating normally

Voltrover-Handlebars-LCD-Display- (3)

How to Remove and Install the Battery

  1. Remove the Parts
    Remove the screws and the battery-securing panel
  2. Remove the battery
    Locate the battery’s handle and remove the battery.
  3. Mount Battery
    Insert battery, refer to Step 1 to place panel and install side screws. Finally connect battery terminals (positive to positive, negative to negative).

Voltrover-Handlebars-LCD-Display- (4)

How to Secure the Brake Cable

  1. Remove the accessories
    Remove the accessories on the left bracket with a tool
  2. Secure the Brake Cable
    Snap the brake cable into the retaining slot, install the securing accessories, and tighten them with a screwdriver.
  3. Secure the Upper Cable
    Secure it to the back of the front panel, locate the retaining clip, and snap the brake cable into it.

Voltrover-Handlebars-LCD-Display- (5)

How to Install the Rear Fender

  1. 1 Remove the Mounting Screw
    Remove the four mounting screws and nuts
  2. 2 Align the Mounting Holes
    Align the rear fender with the frame holes
  3. 3 Tighten the Nut
    Reinstall the nut onto the screw on the other side and fully tighten all fasteners for a secure fit

Voltrover-Handlebars-LCD-Display- (6)

How to Install the Rear Shock

  1. 1 Remove the Parts
    Remove existing mounting bolts and nuts from the frame
  2. 2 Align the Mounting Holes
    Align the rear shock with the upper and lower mounting brackets
  3. 3 Tighten the Screws
    Insert the bolts and secure them using a 12mm and 14mm wrench (used together for proper torque)

Voltrover-Handlebars-LCD-Display- (6)

How to Secure the Front Panel

  1. Remove the accessories
    Take out the screws that secure the front panel
  2. Align the Mounting Holes
    Insert the lower part of the panel into the mounting holes to secure it, then align the upper mounting holes
  3. Secure the Screws
    Secure the screws with a tool, tighten them by rotating, and fasten the front panel

Voltrover-Handlebars-LCD-Display- (8)

How to Install the Front Fender

  1. Remove the Mounting Screw
    Remove the mounting screws using a Phillips screwdriver
  2. Align the Mounting Holes
    Align and secure the new front fender in place

Voltrover-Handlebars-LCD-Display- (9)

How to Install the Front Wheel

  1. Remove the Parts
    Rotate the Nut to remove temporary shipping spacers from the front axle
  2. Mount the Front Wheel
    Install the large round spacer on one side of the axle. Insert the small round spacer on the opposite side
  3. Tighten the Nut
    Secure the axle with the nut and tighten evenly using the 17 wrench

Voltrover-Handlebars-LCD-Display- (10)

How to Install the Front Wheel Disc Brake

  1. Remove Screws
    Unpack the package and remove the screws on the disc brake caliper
  2. Align the Caliper
    Position the disc brake caliper to align with the front wheel
  3. Align Holes Tighten Screws
    Align the holes of the front wheel disc brake components. Use an 8-size wrench to tighten the screws further

Voltrover-Handlebars-LCD-Display- (11)

How to Install the LCD Display

  1. Remove Screws
    Remove mounting screws using a Phillips screwdriver
  2. Align the Mounting Holes
    Align the LCD display with the handlebar mount
  3. Tighten Screws
    Securely tighten both side screws for a stable fit

Voltrover-Handlebars-LCD-Display- (12)

How to Install the Left Baffle

  1. Remove the Parts
    Remove the screws and nuts from the three mounting holes on the left side panel of the body with a tool.
  2. Align the Mounting Holes
    Place the Left Baffle, align it with the mounting holes, and insert the screws.
  3. Tighten the Screws
    Note: Remove battery first if unable to reach rear panel screws; see battery removal page for details. Tighten nuts of rear screws with 10mm wrench inside the body; hold screws in place from outside to prevent rotation.

Voltrover-Handlebars-LCD-Display- (1)

Documents / Resources

PDF thumbnailHandlebars LCD Display
Installation Guide · electric scooter, LCD display, Handlebars LCD Display, LCD Display

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.