Linkwebb CT0306YC Remote Controller Instruction

Linkwebb CT0306YC Remote Controller

Overview

The CT0306YG remote controller provides controls for fan speed, color temperature switching, fan on/off, light on/off, and dimming, with an LED indicator and a learning function to enable direct control or control after learning.

Specifications

Quick Setup

1. Install two AAA 1.5V batteries into the transmitter.
2. Press a key on the remote; confirm the LED indicator turns on.
3. Use the remote keys to control fan speed and color temperature switching.
4. Use the light controls for light ON/OFF and light dimming.
5. Use the learning button to enable control after learning (O/D: direct control vs control after learning).

Features

• Control Interface: Provides physical buttons for accessing the functions supported by the compatible appliance. The available commands depend on the remote controller’s button layout.
• Remote Operation: Allows users to operate supported appliance functions without directly accessing the appliance’s control panel. Effective operation depends on the controller’s communication method and operating conditions.
• Dedicated Function Buttons: Uses individually labeled or symbol-marked buttons to identify available commands. Users should follow the markings on the remote to select the required function.
• Handheld Construction: Features a portable form factor intended for manual operation and convenient placement when not in use.
• Battery-Powered Operation: Uses a battery-based power supply to support operation without a permanent wired connection. The required battery specification must be confirmed before installation.
• Appliance Compatibility: Intended to communicate with equipment supporting the CT0306YC controller. Compatibility with other models should not be assumed.

Operation Instructions

1. LED Indicator
2. Speed of the Fan
3. Color temperature switching
4. Fan OFF
5. Light ON/OFF I Light dimming
6. Learning button
7. OOID:
   1. O-direct control
   2. D-control after learning
8. BATTERY: AAA/1.5Vx2

Maintenance and Cleaning

• Exterior Cleaning: Wipe the remote controller with a soft, dry cloth to remove dust, fingerprints, and surface contamination.
• Stubborn Dirt Removal: Use a slightly damp, lint-free cloth when necessary. Prevent moisture from entering button openings or the battery compartment.
• Battery Inspection: Check the battery compartment periodically for corrosion, leakage, or damaged contacts.
• Battery Replacement: Replace depleted batteries with the type specified inside the battery compartment. Follow the marked polarity during installation.
• Long-Term Storage: Remove the batteries when the controller will remain unused for an extended period to reduce the possibility of battery leakage.
• Button Maintenance: Keep the buttons free from dirt and residue. Avoid applying excessive pressure when operating them.
• Storage Conditions: Store the controller away from direct sunlight, excessive heat, moisture, and locations where it could be dropped or crushed.
• Housing Protection: Avoid using abrasive cleaners, solvents, or sharp tools that could damage the enclosure or button markings.

Safety Tips

• Correct Battery Type: Use only batteries matching the specifications marked on the controller.
• Battery Polarity: Install batteries according to the positive (+) and negative (-) markings to prevent malfunction or damage.
• Battery Handling: Do not mix old and new batteries or different battery types. Do not attempt to recharge non-rechargeable batteries.
• Moisture Protection: Keep the controller away from water, rain, and other liquids unless the manufacturer explicitly specifies water resistance.
• Heat Exposure: Do not place the controller near open flames, heating appliances, or other high-temperature surfaces.
• Physical Damage: Avoid dropping, striking, bending, or applying excessive force to the controller.
• Unauthorized Modification: Do not disassemble, modify, or attempt to repair internal electronic components.
• Child Safety: Keep loose batteries and accessible battery compartments away from young children. Secure the battery cover after installation.
• Equipment Compatibility: Use the controller only with equipment confirmed to support its commands.
• Damaged Components: Stop using the controller if the housing, battery contacts, or internal components show signs of damage.

Use precautions

1. When you press the key on the transmitter, the LED indicator doesn’t turn on; please inspect the battery installation.
2. When press the key of transmitter, the LED indicator flashing, that means the battery get lowvoltage, please replace a new one.
3. Please remove the battery from the transmitter when leaving it unused for a long time.

 FCC STATEMENT

This product has been tested and found to comply with the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This product generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the product and receiver.
• Connect the product to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may causeUndesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product. FCC ID: 2ABUP-CT0306YG

IC Caution
RSS-Gen Issue 5 “&” RSS-Gen numéro 5
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RF exposure statement
The equipment complies with the IC Radiation exposure limit set forth for an uncontrolled environment.

Troubleshooting

• LED indicator does not turn on when pressing a key: Inspect battery installation.
• LED indicator flashes when pressing a key: Battery voltage is low—replace with new batteries.
• Remote not used for a long period: Remove batteries from the transmitter.