VEVOR SK Workbench Instruction Manual

VEVOR-logo

VEVOR SK Workbench

VEVOR-SK-Workbench-product

Product Parameters

Item No. Maximum load-bearing Product Size

(mm)

Table legs ( whole / Back board Support feet Wheel
  (Top board/Clap

board)

  separated)      
SCGZT610*355T 300/200lbs 356*610*864 separated × √ ×
HETG-30*36 470/350lbs 762*914*954.6 whole × × √
SKT1520*760T 900/620lbs 762*1524*660 whole √ √ ×
SKT710*610T 700/540lbs 610*711*660 whole √ √ ×
SKT910*760T 800/620lbs 762*914*660 whole √ √ ×
SKT1220*760T 900/620lbs 762*1219*660 whole √ √ ×
HETG-30*48 500/370lbs 762*1219*954.6 whole × × √
GZT910*610J 430/320lbs 610*914*954.6 whole × × √
SKT610*610J 700/540lbs 610*610*751.6 whole √ × √
SKT710*610J 700/540lbs 610*711*751.6 whole √ × √
SKT910*760J 800/620lbs 762*914*751.6 whole √ × √
HETG-30*60 520/390lbs 762*1524*954.6 whole × × √

Note from manual: Parts details 1–8 are available for all models; parts details 9–14 are only available for specific J models listed in the packing list.

WORKBENCH

MODEL: SKT710*610T、SKT910*760T、SKT1220*760T、SKT1520*760T、 SKT610*610J、SKT710*610J、SKT910*760J、GZT910*610J、 SCGZT610*355T、HETG-30*36、HETG-30*48、HETG-30*60

VEVOR-SK-Workbench-Fig- (1)

This is the original instruction; please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us; we won’t inform you again if there are any technology or software updates on our product.

VEVOR-SK-Workbench-Fig- (2)

SAFETY INSTRUCTIONS

WARNING:
Read this material before using this product. Failure to do so can result in serious injury.

  1. The product complies with relevant standards and regulations. Installation of this device must comply with all applicable regulations, and it should only be operated in well-ventilated areas. Please read the user manual before installing and using this equipment.
  2. This product is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  3. Children shall not play with the appliance.
  4. This product shall not be used by children.
  5. This product is intended to be used in household and similar applications such as:
    • staff kitchen areas in shops, offices and other working environments;
    • farmhouses;
    • by clients in hotels, motels and other residential type environments;
    • bed and breakfast type environments.
  6. Please properly keep product. Check whether the product is abnormal before use. If it is abnormal, please stop using it.
  7. Please use the product according to the intended use, warn of potential injury from misuse.

Assembly precautions

  1. Assemble only according to these instructions. Improper assembly can create hazards.
  2. Keep the assembly area clean and well-lit.
  3. Keep bystanders out of the area during assembly.
  4. Do not assemble when tired or when under the influence of alcohol, drugs, or medication.
  5. The product capabilities apply to properly and completely assembled products only.
  6. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.

Use precautions

  1. Use with products heavier than the rated weights indicated may result in instability, causing possible injury.
  2. Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
  3. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
  4. Use the mounting screws provided and DO NOT OVERTIGHTEN mounting screws.
  5. This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
  6. This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

SAVE THESE INSTRUCTIONS

PACKING LIST

VEVOR-SK-Workbench-Fig- (3)VEVOR-SK-Workbench-Fig- (4) VEVOR-SK-Workbench-Fig- (5)VEVOR-SK-Workbench-Fig- (6)

ASSEMBLY STEP

This is the original instruction; please read all manual instructions carefully before operating.VEVOR reserves clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us; we won’t inform you again if there are any technology or software updates on our product.

Kindly Reminded. Please Wear Gloves To install This Product.

  1. Place the Top board mounting hole facing upwards, install the round pipe into the hole, fix it with M6 socket screws, and apply a torque greater than or equal to 25N.mVEVOR-SK-Workbench-Fig- (7)
  2. Some models distinguish between the upper and lower support pipes, and the upper and lower support pipes need to be covered.
    Note: This step can be omitted for products with whole legs;VEVOR-SK-Workbench-Fig- (8)
  3. Install the partition according to the height of the hole position you need; fix the mounting hole with M6 socket screws, and the torque is greater than or equal to 25N.mVEVOR-SK-Workbench-Fig- (9)
  4. Install the casing knock into the round pipe.VEVOR-SK-Workbench-Fig- (10)
  5. Install the support feet or wheelsVEVOR-SK-Workbench-Fig- (11)
  6. After completing the installation, turn the workbench over and adjust the height of the four support feet (or wheels) to ensure that the four feet are close to the ground and the workbench is stableVEVOR-SK-Workbench-Fig- (12)

Note: If the workbench does not need to be moved. Please hold the brakes on the wheels to ensure that the table does not move.
The workbench has a maximum weight limit; please be careful not to exceed the maximum weight.

Note:Below installation steps only for SKT610*610J、SKT910*760J、 SKT710*610J、SKT1520*760T、SKT1220*760T、SKT910*760T、SKT710*610T 1. Install the flapper-1 on the workbench in the correct orientation (please refer to the logo direction), then tighten it with M5*12 screws and M5 flat pads, and fasten the baffle-1 to the workbench.

VEVOR-SK-Workbench-Fig- (13)

  1. The baffle-2 and the baffle-1 are buckled and correctly placed on the workbench, and then fastened with M5*12 screws and M5 flat pads, and the baffle plate 1 is fastened on the workbench. (The installation steps of Bezel-3 are similar; please refer to this step)VEVOR-SK-Workbench-Fig- (14)
  2. Finished product drawing SKT610*610J, SKT910*760J, SKT710*610JVEVOR-SK-Workbench-Fig- (15)

Troubleshooting

  • Workbench is unstable after assembly: Turn the workbench over again and re-adjust the height of the four support feet (or wheels) so all four feet are close to the ground and the workbench is stable.
  • Workbench moves unintentionally: If it does not need to be moved, hold the brakes on the wheels to ensure the table does not move.
  • Installation step/part differs by model: Follow the “below installation steps only for” section for the listed J models when installing the flapper components (flapper-1/flapper-2/flapper-3).
  • Before use, something seems wrong: Check whether the product is abnormal before use; if abnormal, stop using it.

Documents / Resources

PDF thumbnailSK Workbench
Instruction Manual · SK, SK Workbench, Workbench

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.