Eclipse HX digital matrix system

Overview
This quick start guide explains how to set up and configure a basic Eclipse HX digital matrix system, including device connections, installing the EHX configuration software, discovering the matrix in EHX, and applying configurations to the matrix.
Specifications
- Default matrix IP (when no DHCP server is available): 169.254.0.100
- Required/mentioned interface cards: MVX-A16, E-IPA, E-Dante64, E-MADI64, E-FIB
Quick Guide
- Connect Eclipse HX devices: Ensure the matrix is powered off, confirm required interface cards/modules are installed, connect user stations/interfaces/networks as required, connect the matrix to your network, then power on.
- Prepare the EHX PC: Connect the EHX PC to the same network as the matrix.
- Install EHX software: In the Eclipse HX software distribution package, run the installer for EHX Client or EHX Server (Server only if running Client-Server mode), follow the Setup Wizard, then run EHX.
- Discover the matrix in EHX: Create a new EHX project when prompted, power on the matrix if not already powered, then locate the matrix in the Discovery pane and drag it to the Layout screen.
- Save and retrieve the map: Save the project and use Retrieve Map from Matrix.
- (Optional but recommended) Set a static IP: Right-click the matrix in Layout, select Change IP Address, adjust settings, then apply changes and Apply Map to Matrix.
- Apply configuration: In EHX, click Apply Map to Matrix to apply the project configuration to the matrix. After reset, confirm the matrix appears green on the Layout screen.
- Complete configuration steps: Use the EHX sidebar menus to complete mandatory items (highlighted in amber), then finish by applying the map to the matrix.
INTRODUCTION
This quick start guide describes how to set up a basic Eclipse® HX digital matrix system.
It explains how to:
- Connect interface cards, user panels, and other devices to the matrices.
- Set up the EHX configuration software on the PC.
- Set up and configure the matrix.
- Tip: For detailed help with setting up and configuring your Eclipse HX system, see the full Eclipse HX documentation set available in the Eclipse HX software distribution package.
Connecting your Eclipse HX devices
- Ensure the Eclipse HX matrix is powered off.
- Confirm the required interface cards (MVX-A16, E-IPA, E-Dante64, E-MADI64, E-FIB) and interface modules are installed in the matrix.
- Connect user stations, interfaces, and networks as required.
- Connect the matrix to your network.
- Power on the Eclipse HX matrix.
Connecting the EHX PC
- The Eclipse HX matrix is set up to automatically obtain an IP address from a DHCP server on your network. If no DHCP server can be located, the matrix defaults to the IP address of 1692540100.
- When the installation is complete, run the EHX software.
Installing the EHX configuration software
- The EHX configuration software is included in the Eclipse HX software distribution package. Separate installers are provided for the EHX Client and EHX Server. Run the appropriate installer and follow the EHX Setup Wizard instructions.

Note: Only select the server installation if you want to run EHX in Client-Server mode, where multiple clients are connected to a shared central configuration server.
Discovering the matrix in EHX
To discover the matrix (and associated cards and ports) in EHX:
- Connect your EHX PC to the same network that your matrix is connected to.
- Run EHX. You will be prompted to create a new EHX project. A project holds the configurations that can be applied to one or more matrices.
- If your matrix is not powered yet, power it now. Your matrix will now be seen on the Layout screen, in the Discovery pane.

- Drag the matrix to the Layout screen to bring it into your project.
- Save the project.
- Retrieve Map from Matrix.
- Note: The matrix may not be discovered if broadcast ports are blocked on the networks. In this case, right-click on the Layout area, add the new matrix, and enter its IP address.
- You should now be able to retrieve the map. If broadcasts are blocked, some discovery-dependent functions (for example, retrieving a map) may be unavailable.
Configuring the Matrix
IP address
By default, the Eclipse HX matrix automatically obtains an IP address from the network (see Section 1.2). However, Clear-Com strongly recommends setting a static IP address before normal operation. To set a static IP address on the matrix:
- 1. In EHX, right-click the matrix on the Layout screen.
- 2. Select Change IP Address. The current IP settings are displayed.
- 3. Make any desired adjustments to the IP settings.
- 4. Apply the changes to the matrix (then Apply Map to Matrix).
Applying a configuration
- In EHX, the matrix initially appears in the amber state. This indicates the current project configuration has not yet been applied to the matrix. To apply the configuration, select Apply Map to Matrix.
- Note: If the matrix is not shown but you can apply or retrieve configuration maps, status traffic may be blocked by the network or your computer. Ensure EHX is allowed through your computer’s firewall.
- After the configuration is applied, the matrix resets. When it returns to the network, it is displayed as green on the Layout screen (the matrix is now running the configuration from this project).
Configuring the system
- The EHX sidebar menus list the available configuration options, based on the interface cards and user panels associated with the matrix.
- Mandatory steps that are not yet complete are highlighted in amber.
- To see what is missing, hover over the amber menu item.

Basic configuration steps (example):
Hardware
- Configure cards, their IP settings & label any ports
- Register FreeSpeak wireless transceivers in the Transceivers screen
- Register FreeSpeak beltpacks in the Access screen
Configuration
- Create and label roles for FreeSpeak wireless beltpacks
- Create, label, and associate interfaces with any partylines, fixed groups, IFB, and other functions as needed
- Assign keys to panels
- When done, apply the map to the matrix
- Tip: Any changes that you make can be applied to the matrix by clicking Apply Map to Matrix in the EHX sidebar.
- For more information, go to the Eclipse HX Knowledge Center on the Clear-Com website.
Troubleshooting
- Matrix not discovered in EHX: If broadcast ports are blocked on the network, discovery may fail. Right-click the Layout area, add the new matrix, and enter its IP address.
- Note that some discovery-dependent functions (e.g., retrieving a map) may be unavailable when broadcasts are blocked.
- Cannot apply or retrieve configuration maps: If the matrix is not shown but you can apply/retrieve maps, status traffic may be blocked. Ensure EHX is allowed through your computer’s firewall and that required network traffic is permitted.
Documents / Resources
![]() | Eclipse HX digital matrix system |
References
- User Manualmanual.tools

