Yamaha YDS-150 Digital Saxophone Instruction Manual

Yamaha YDS-150 Digital Saxophone
Instruction Manual

 

Yamaha YDS-150 Digital Saxophone Manual

Yamaha YDS-150 Digital Saxophone Figure

SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Yamaha Music Europe GmbH declares that the radio equipment type [model 1, model 2, model 3] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://europe.yamaha.com/en/support/compliance/doc.html

Importer: Yamaha Music Europe GmbH
Siemensstrasse 22-34, 25462 Rellingen, Germany

  • Radio Frequency (Operational Frequency)………2402 MHz to 2480 MHz
  • Maximum Output Power (EIRP) …………………….4.0 dBm (2.5 mW)

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

  1. This device may not cause interference; and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without testing of specific absorption rate (SAR).

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that is deemed to comply without testing of specific absorption rate (SAR).

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.

Warning IconWARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Power

  • Do not place the USB cable near heat sources such as heaters or radiators. Also, do not excessively bend or otherwise damage the cord, or place heavy objects on it.
  • Only use the voltage specified as correct for the instrument. The required voltage is printed on the name plate of the instrument.
  • Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.

Do not open

  • This instrument contains no user-serviceable parts. Do not open the instrument or attempt to disassemble or modify the internal components in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel.

Water warning

  • Do not expose the instrument to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the instrument, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument inspected by qualified Yamaha service personnel.
  • Never insert or remove an electric plug with wet hands.

Fire warning

  • Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.

Influences on electro-medical devices

Radio waves or magnetism may affect electro-medical devices.

  • Do not use this product near medical devices or inside areas in which the use of radio waves is restricted.
  • Do not use this product within 15cm (6 in.) of persons with a heart pacemaker or defibrillator implant.

Battery

  • Follow the precautions below. Failure to do so might result in explosion, fire, overheating or battery fluid leakage.
    • Do not tamper with or disassemble batteries.
    • Do not dispose of batteries in fire.
    • Do not attempt to recharge batteries that are not designed to be charged.
    • Keep the batteries separate from metallic objects such as necklaces, hairpins, coins, and keys.
    • Use the specified battery type (page 15) only.
    • Use new batteries, all of which are the same type, same model, and made by the same manufacturer.
    • Always make sure all batteries are inserted in conformity with the +/- polarity markings.
    • When the batteries run out, or if the instrument is not to be used for a long time, remove the batteries from the instrument.
    • When using Ni-MH batteries, follow the instructions that came with the batteries. Use only the specified charger device when charging.
  • Keep batteries away from small children who might accidentally swallow them.
  • If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid should come in contact with your eyes, mouth, or skin, wash immediately with water and consult a doctor. Battery fluid is corrosive and may possibly cause loss of sight or chemical burns.

If you notice any abnormality

  • When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. (If you are using batteries, remove all batteries from the instrument.) Then have the device inspected by Yamaha service personnel.
    • The USB cable or plug becomes frayed or damaged.
    • It emits unusual smells or smoke.
    • Some object has been dropped into the instrument.
    • There is a sudden loss of sound during use of the instrument.
    • If any cracks or breakages exist on the instrument.

Caution IconCAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following:

Power

  • Do not connect the instrument to an electrical outlet using a multiple connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet.
  • When removing the electric plug from the instrument or an outlet, always hold the plug itself and not the USB cable. Pulling by the USB cable can damage it.
  • Remove the electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical storms.
  • Use the specified USB power adaptor (page 10) only. Using the wrong adaptor can result in damage to the instrument or overheating.

Location

  • Do not place the instrument in an unstable position where it might accidentally fall over.
  • Before moving the instrument, remove all connected cables, to prevent damage to the cables or injury to anyone who might trip over them.
  • When using an electric plug, make sure that the AC outlet you are using is easily accessible in plain view. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to disconnect the plug from the wall AC outlet.

Connections

  • Before connecting the instrument to other electronic components, turn off the power for all components. Before
    turning the power on or off for all components, set all volume levels to minimum.
  • Be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level.

Handling

  • Do not insert a finger or hand in any gaps on the instrument.
  • Never insert or drop paper, metallic, or other objects into the gaps on the panel or keys. This could cause physical injury to you or others, damage to the instrument or other property, or operational failure.
  • Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors.
  • Do not use the instrument if the mouthpiece, reed or ligature is damaged.
  • Keep small parts out of the reach of infants. Your children may accidentally swallow them.
  • Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.
  • When using a strap, make sure the strap is securely attached to the instrument.
  • Do not lift the instrument by the strap. It can cause serious injury or damage to the instrument.
  • Do not treat the instrument in a rough manner such as swinging it about, etc. The strap on the instrument may detach causing unexpected accidents such as the instrument dropping, etc., or injuring persons close by.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.
Even when the [Power Button] (Standby/On) switch is in standby status (power lamp is off), electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet. Make sure to discard used batteries according to local regulations.

NOTICE

To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.

Handling

  • Do not connect this product to public Wi-Fi and/or Internet directly. Only connect this product to the Internet through a router with strong password-protections. Consult your router manufacturer for information on security best practices.
  • Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise. When you use the instrument along with an application on your smart device such as a smartphone or tablet, we recommend that you set Bluetooth to on after setting “Airplane Mode” to on on that device in order to avoid noise caused by communication.
  • Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation. (Verified operating temperature range: 5° – 40°C, or 41° – 104°F.)
  • Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or key-board.
  • Do not leave the instrument for a long period of time with a key pressed, since this might damage the key.

Maintenance

  • When cleaning the instrument, use a soft cloth. Do not use paint thinners, solvents, alcohol, cleaning fluids, or chemical-impregnated wiping cloths.
  • Be careful not to expose the instrument to water. If any water gets on the instrument, wipe it off using a dry cloth.

Information

About this manual

  • The illustrations and LED displays as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument.
  • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under license.

Bluetooth Icon

  • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

About Bluetooth

Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft.), and employs the 2.4 GHz frequency band.

Handling Bluetooth communications

  • The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of equipment. While Bluetooth compatible devices use a technology minimizing the influence of other components using the same radio band, such influence may reduce the speed or distance of communications and in some cases interrupt communications.
  • The speed of signal transfer and the distance at which communication is possible differs according to the distance between the communicating devices, the presence of obstacles, radio wave conditions and the type of
    equipment.
  • Yamaha does not guarantee all wireless connections between this unit and devices compatible with Bluetooth function.

Your particular instrument does not have Bluetooth capability if a “Y” indication is printed on the upper right corner of the label at the bottom.

Thank you for purchasing the Yamaha Digital Saxophone! This digital saxophone can be used for playing and practicing at home. We recommend that you read this manual carefully so that you can fully take advantage of the advanced and convenient functions of the instrument. We also recommend that you keep this manual in a safe and handy place for future reference.

Included Accessories

  • Mouthpiece set (mouthpiece, ligature, cap, reed) × 1 Yamaha YDS-150 Digital Saxophone - Mouthpiece set
  • Strap × 1 Yamaha YDS-150 Digital Saxophone - Strap
    • NOTE
      • The strap is stored in the pocket inside the special case.
  • Replacement O-ring × 1 set (3 pieces included) Yamaha YDS-150 Digital Saxophone - Replacement O-ring
  • Replacement reed × 1 Yamaha YDS-150 Digital Saxophone - Replacement reed
  • Special case × 1
    • NOTICE
      • Make sure to only store this instrument and the strap inside the special case, since storing other things might damage the keys.
  • Owner’s Manual × 1

Controls and Functions

Front side Yamaha YDS-150 Digital Saxophone - Controls and Functions - Front side

Left side Yamaha YDS-150 Digital Saxophone - Controls and Functions - Left side

Back Side Yamaha YDS-150 Digital Saxophone - Controls and Functions - Back side

Laying the Instrument Down
When the instrument is not being played, place it on a flat surface as shown in the illustration below. Do not place the instrument on a chair, music stand, or other such unstable surface, as there is a risk of the instrument falling. Also, never lean the instrument up against a wall, etc.

Yamaha YDS-150 Digital Saxophone - Laying the Instrument Down

NOTICE

  • Do not stand the instrument up by itself. Doing so can cause damage to the instrument due to the impact if it falls down. If you want to stand the instrument up, please use a commercially available stand.
  1. Mouthpiece set
    For use exclusively with this instrument.
  2. Keys
    (Fingering Chart: page 20)
  3. Bell
    There is a water drain inside the bell. Water condensation and excess breath moisture can be drained from here.
  4. 5 V DC-IN/USB TO HOST terminal
    • Micro USB Type-B terminal.
      For connection to a USB power adaptor, USB mobile battery, or PC with a USB cable.
    • NOTICE
      • Use a USB A to micro B cable of less than 3 meters. Do not use a USB 3.0 cable.
  5. PHONES jack
    For connecting a pair of stereo headphones or other equipment with a mini stereo phone plug (3.5 mm). The instrument’s built-in speakers automatically stop producing sound when plugged in.
    • Caution Icon CAUTION
      • To prevent hearing loss, avoid using headphones at high volumes for extended periods of time.
      • Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. This can cause permanent hearing loss.
  6. AUX IN jack
    For inputting the sound of an audio player and listening to it through the built-in speaker of the instrument (with a 3.5 mm, mini stereo phone plug). To adjust the input volume from the [AUX IN] jack, adjust the audio play- back volume on the audio device.
    • Caution Icon CAUTION
      • To avoid possible damage, first turn on the power for the external device, and then for the instrument. When turning off the power, first turn off the power for the instrument, and then for the external device. This can cause permanent hearing loss.
    • NOTE
      • Use an appropriate adaptor plug if the output jack of the audio device does not match the stereo mini phone plug of the audio cable.
      • Use audio cables and adaptor plugs that have no series resistors.
  7. [Power Button] (Standby/On) button
    Press this button to turn on the instrument.
  8. LED screen
    Displays information such as the Voice number in alphanumeric characters.
  9. VOICE [Voice Up Button]/[Voice Down Button] buttons
    Changes the Voice each time a button is pressed.
  10. VOL [-]/[+] buttons
    Raises or lowers the instrument volume each time a button is pressed. Press and hold a button to change the volume quickly.
    • Setting range: 0 to 15, od (Default: 13)
    • Press the VOL [-] button and VOL [+] button simultaneously to restore the default volume setting.
  11. [Fn] (Function) button
    Press specific keys while holding this button to call up various functions. This is also used to operate some functions.
  12. Power lamp
  13. Bluetooth lamp
  14. Strap ring
    Attach the included strap to this ring.
    • How to Attach the Strap
      Firmly attach the included strap to the ring. You can easily change the length of the strap to adjust it to a length that is easy for you to use. Yamaha YDS-150 Digital Saxophone - How to Attach the Strap
  15. Thumb hook
    Use this hook to support the instrument with your thumb when playing. Wrap your right thumb around the thumb hook to hold the instrument firmly.
  16. Analog controller
    Used to apply changes to the Voice.

Before Playing

Power Requirements

This instrument can be powered in one of the two ways listed below. Determine which you intend to use, and follow the
instructions for setting up.

NOTICE

  • If you connect the instrument to a commercially available USB power adaptor or USB mobile battery while batteries are in the instrument, priority is given to power from the USB cable.

Using batteries

This instrument requires four “AAA” size, alkaline (LR3) batteries or rechargeable nickel-metal hydride batteries (rechargeable Ni-MH batteries).

  1. Make sure that the power of the instrument is off. The power lamp (power lamp Button) will be off when the power is off.
  2. Place the instrument upside-down on a soft cloth and remove the battery cover.
  3. Insert the four new batteries, being careful to follow the polarity markings on the inside of the compartment. Yamaha YDS-150 Digital Saxophone - Insert the four new batteries

Remaining Battery Power

When the remaining battery power drops to about 5 or 10 minutes*, the POWER LED lamp (power lamp Button) flashes. Further-more, when there is almost no remaining power, the POWER LED lamp turns off and the instrument enters standby mode.

  • Varies depending on the usage environment.
    • NOTE
      • You should check the Power lamp frequently and take
        precautions that the battery does not run out during a
        performance.

Using a USB power adaptor or USB mobile battery (sold separately)

Connect the USB cable to a USB power adaptor or USB mobile battery (sold separately) in the order shown in the illustration. Follow the order shown here in reverse when disconnecting the USB cable. Yamaha YDS-150 Digital Saxophone - Using a USB power adaptor

Use only a USB power adaptor or USB mobile battery compatible with the USB standard for power supply.

Output voltage 4.8 V to 5.2 V
Output current 1.0 A or greater

Caution IconCAUTION

  • Before using a USB power adaptor or USB mobile battery, be sure to read the relevant pre- cautions.

Turning on the Power / Setting to Standby

Press the [Power Button] (Standby/On) button to turn the power on.

The power lamp (power lamp Button) is lit in red when the power is on. Adjust the volume as desired while blowing into the mouthpiece. Yamaha YDS-150 Digital Saxophone - Turning on the Power

Caution Icon

CAUTION

  • Do not use the instrument or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss.

NOTICE

  • While turning on the power, do not attempt any other operations, such as blowing into the mouthpiece. Doing so may cause the instrument to malfunction.

Press and hold the [Power Button] (Standby/On) button for longer than one second to enable standby mode

Warning Icon

CAUTION

  • Even when in standby mode, an electric current is still flowing in the instrument at the minimum level. When you are not using the instrument for a long time, make sure to disconnect the USB power adaptor from the AC outlet, or remove the batteries from the instrument.

NOTE

  • If over 5 seconds elapses with no keys or buttons operated since the power was turned on, the LED display turns off. Simply operate any button or move the instrument to turn the LED display on again.

Enabling / Disabling Auto Power Off

To prevent unnecessary power consumption, this instrument features an Auto Power Off function that automatically turns the power off if the instrument is not operated for a specified period of time (30 minutes). By default, it is set to On; however, this setting can be changed with the [Fn] button.

NOTICE

  • If your instrument is connected to other equipment such as amplifiers and speakers but you do not intend to use it for 30 minutes, we recommend that you turn off all devices as described in the corresponding owner’s manuals. Doing so eliminates the risk of damage to the other equipment. If you do not want the instrument to turn off automatically when connected to other equipment, disable the Auto Power Off function.

Adjusting the Instrument Volume

Adjust the volume.
The volume is increased by 1 each time VOL [+] is pressed. The volume is decreased by 1 each time VOL [-] is pressed. You can adjust the volume in a range of 0 to 15, od. The default value is 13. Yamaha YDS-150 Digital Saxophone - Adjusting the Instrument Volume

The “od” (overdrive) setting is the maximum volume, for the most powerful sound. Keep in mind that there may be distortion in the sound for specific Voices and in the lower ranges.

Initialization

Perform this operation when you want to reset all settings to their factory defaults.

  1. If the power is on, turn the power off.
  2. Turn the power on while holding keys [1], [p], and [3]. Yamaha YDS-150 Digital Saxophone - Initialization

Playing the Instrument

Mouth Shape

Position the mouthpiece in your mouth with your upper front teeth resting about 1cm from the tip of the mouth- piece. Cover your lower teeth with your lower lip to keep your teeth from coming into direct contact with the reed. Yamaha YDS-150 Digital Saxophone - Mouth Shape

With the reed resting on your lower lip, seal your mouth around the mouthpiece to keep air from leaking out of the corners of your mouth when blowing.
* Do not bite hard on the reed or mouthpiece. Yamaha YDS-150 Digital Saxophone - Mouth Shape 1

How to Play Sound

Put the mouthpiece into your mouth and blow. Blow strongly for a higher volume, and softly for a lower volume. There is no need to vibrate the reed like an acoustic saxophone.

NOTE

  • Unlike an acoustic saxophone, changing the degree to which the mouthpiece is inserted into the neck will not change the pitch of the sound.

Selecting a Voice

It is possible to select a Voice and tonality you like, such as an alto saxophone, tenor saxophone, etc.

Press VOICE [Voice Up Button]/[Voice Down Button].
The Voice number is displayed on the LED display. For
the Voice names, refer to the Voice List on page 19. Yamaha YDS-150 Digital Saxophone - Press VOICE

The display on the LED screen has the following meanings.

Alto sax Voices (in Eb)Alto sax Voices (in Eb)

Soprano sax Voices (in Bb)Soprano sax Voices (in Bb)

Tenor sax Voices (in Bb)Tenor sax Voices (in Bb)

Baritone sax Voices (in Eb)Baritone sax Voices (in Eb)

Non-sax Voices (in C)Non-sax Voices (in C)

You can select user Voices editedYou can select user Voices edited in the dedicated app (page 14). For details, refer to the manual for the dedicated app.

Using the Analog Controller

The analog controller has functions assigned by default depending on the selected Voice.

  • Raising or lowering the pitch (Pitch Bend)
  • Applying vibrato to the sound. (Modulation)
  • Smoothing out the pitch slide between notes (Portamento)

For details about the functions assigned to the analog controller for each Voice, see the Voice List at the end of this document. Yamaha YDS-150 Digital Saxophone - Using the Analog Controller

NOTE

  • Portamento is a playing technique that smoothly slides the pitch of the performance up and down. When using a Voice with portamento assigned to it, move the thumb controller to smoothly change the pitch.

Changing Settings with the [Fn] Button

Press specific keys while holding the [Fn] button to perform settings for the various functions of the instrument.

Basic operations

Use the following procedure to perform settings for each function.

  1. While holding the [Fn] button, press the key to which the function is assigned. Hold the [Fn] button until you finish performing settings. If you release the button, the value at that moment is set and operation returns to the Voice selection screen. Yamaha YDS-150 Digital Saxophone - While holding the [Fn] button, press the key to which the function is assigned
  2. While holding the [Fn] button, press VOICE [Voice Up Button]/[Voice Down Button] and select the desired value. Yamaha YDS-150 Digital Saxophone - While holding the [Fn] button, press VOICE up or down
    • NOTE
      • Press both VOICE [Voice Up Button]/[Voice Down Button] buttons simultaneously to restore the value to the factory default.
  3. When you have finished selecting a value, release the [Fn] button.
    This will complete the setting and return the operation to the Voice selection screen. Yamaha YDS-150 Digital Saxophone - When you have finished selecting a value, release the [Fn] button

Turning the Bluetooth function on and pairing with your smart device

  1. Turn the Bluetooth function on.
    When it is on, the Bluetooth lamp (BT Button) will flash slowly. Perform pairing when you want to use Bluetooth Audio.
  2. While holding the [Fn] button, press the C key. This puts the instrument in pairing standby. Keep holding the [Fn] button.
    • LED screen: [B–] Pairing standby
    • LED screen: [—] Bluetooth function off
  3. While holding the [Fn] button, press the VOICE [Voice Up Button] button to begin pairing. 
    The LED screen will change to the following display and the Bluetooth lamp ( ) will flash rapidly. Yamaha YDS-150 Digital Saxophone - While holding the [Fn] button, press VOICE up
    • NOTE
      • To cancel the pairing, press the VOICE [Voice Down Button] button.
  4. Select the connection on the smart device.
    Select [YDS-150 Audio] if handling audio.
  5. When pairing is complete, the Bluetooth lamp will switch from quickly flashing to staying on.
    If pairing fails, the Bluetooth lamp flashes slowly and the LED display changes to [B–].
  6. If five minutes elapse since starting pairing in Step 3, pairing fails.
  7. Release the [Fn] button.
    Operation returns to the Voice selection screen.
    • NOTE
      • While paired, the Bluetooth lamp stays lit up.
      • Depending on your smart device, audio can play at a high or uncomfortable volume level. Adjust the volume of your smart device before playing audio.

Using the Dedicated App

You can use the dedicated app for this instrument to perform settings for the functions of this instrument more conveniently.

  1. Install the dedicated app for this instrument on your smart device.
  2. Connect this instrument and your smart device via Bluetooth.

You can perform the following settings for this instrument on the app. For details, refer to the manual for the app.

  • Editing user Voices / editing fingering information / enabling and disabling Voice selection shortcuts, etc.

Instrument Maintenance after Playing

Before storing this instrument in its case, remove the mouthpiece from this instrument and wipe off any moisture near the bell and mouthpiece.

  1. Loosen the ligature screws and remove the reed and ligature from the mouthpiece. Yamaha YDS-150 Digital Saxophone - Loosen the ligature screws
  2. Hold the mouthpiece firmly and turn it from side to side to slide it off from the neck. Yamaha YDS-150 Digital Saxophone - Hold the mouthpiece firmly
    • NOTICE
      • When removing the mouthpiece, avoid applying a bending force to the neck base. Excessive force applied to the neck can damage it.
  3. Use a cleaning swab (sold separately) to clean the inside of the mouthpiece.
    • Be careful not to damage the tip of the mouthpiece.
    • Always keep the cleaning swab clean and dry. Yamaha YDS-150 Digital Saxophone - Use a cleaning swab
  4. Wipe the bell and keys with a dry, soft cloth.

Setting the Reed and Ligature

Slide the mouthpiece onto the body’s neck, turning from side to side. After attaching the mouthpiece, set the reed and ligature onto the mouthpiece.

NOTICE

  • The reed tip is delicate so please take care not to damage it with the ligature, etc. Yamaha YDS-150 Digital Saxophone - Slide the mouthpiece onto the body’s neck
  1. Slide the ligature onto the mouthpiece from its tapered end.
  2. Position the reed so that the edge of the mouth-piece is slightly visible over the reed tip. Tighten the two screws on the ligature to secure the reed in place.
    • Position the ligature so that the tuning fork logo is centered in the ligature’s open space. Yamaha YDS-150 Digital Saxophone - Position the reed

NOTICE

  • Use the dedicated mouthpiece set (mouthpiece, reed, ligature) included with this instrument. Failure to do so can result in sound not being produced properly or other malfunctions.
  • Tighten the ligature screws just enough to keep the reed from moving. Take care not to over-tighten.
  • Do not wash this instrument or the instrument interior with water. Doing so can result in damage to the instrument.
  • Do not apply grease to the instrument neck. Doing so can result in damage to the neck.
  • When the connection between the neck and the mouth-piece is getting looser, replace the O-ring with the included replacement one.
  • If over the course of use the tip of the reed is broken off or the reed becomes disfigured, replace it with the included replacement reed.

Troubleshooting

Sound does not stop.

  • Try turning the power on again.
  • Fluid remaining on the hole inside the mouthpiece joint may result in the sound not stopping. Remove fluid from the hole by using a slim cotton swab.

Specifications

  • Product name : Digital Saxophone
  • Voices : AWM Sampling
  • Bluetooth :
    • Bluetooth version: 4.2
    • Supported profile: A2DP
    • Complies with Bluetooth Low Energy MIDI Specification
    • Wireless output: Bluetooth Class 2
    • Maximum communication distance: About 10 m
    • Radio frequency (Operation frequency): 2,402 to 2,480 MHz
    • Maximum output power (EIRP): 4 dBm
    • Type of modulation: FHSS
  • Power supply :
    • USB AC adaptor: 5 V / 1 A
    • Self-powered USB hub: 5 V / 1 A
    • Four “AAA” size alkaline (LR3) or Ni-MH rechargeable (HR3) batteries
  • Power consumption : 4.5 W (when using a USB AC adaptor)
  • Auto Power Off : Yes
  • Size (W x D x H) : 699 mm (W) × 110 mm (D) × 103 mm (H)
  • Weight : 1.0 kg (not including batteries)

The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file.
Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

For electrical and electronic products using batteries.

should not be mixed with general household wasteInformation for users on collection and disposal of old equipment and used batteries:
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

These symbols are only valid in the European UnionFor business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

These symbols are only valid in the European UnionInformation on Disposal in other Countries outside the European Union:
These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

chemical symbolNote for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the EU Battery Directive for the chemical involved.

Important Notice:
U.S. LIMITED WARRANTY for Customers in the United States

For detailed information about this Yamaha product and warranty service, please either visit the following website address (printable file is available at our website) or contact Customer Service at the address or telephone number identified below.

Website Address:
https://usa.yamaha.com/support/warranty/index.html

Customer Service:
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena Park, CA
90620-1273 Telephone: 800-854-1569

Voice List

Yamaha YDS-150 Digital Saxophone - Voice List 1Yamaha YDS-150 Digital Saxophone - Voice List 2Yamaha YDS-150 Digital Saxophone - Voice List 3Yamaha YDS-150 Digital Saxophone - Voice List 4

Fingering Chart

Close Button

Close

Open Button

Open

This chart shows typical fingerings for saxophones. The music notation is the written pitch, and not the concert pitch.

Yamaha YDS-150 Digital Saxophone - Fingering Chart 1Yamaha YDS-150 Digital Saxophone - Fingering Chart 2

PHONES

Yamaha YDS-150 Digital Saxophone - PHONESMake sure the PHONES jack is facing up.

NOTICE
• Make sure that the PHONES jack is facing up when storing the instrument in the case. Failing to do so can cause damage to the keys.

4000517700

http://www.yamaha.com.cn

Manual Development Group
©2020 Yamaha Corporation
Published 07/2020
2020

VDH5520


Yamaha YDS-150 Digital Saxophone Instruction Manual – Optimized PDF
Yamaha YDS-150 Digital Saxophone Instruction Manual – Original PDF

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. How do I remove the lower octave key? I keep pressing by mistake

    Claude Terrell asks How do I remove the lower octave key? I keep pressing by mistake
    Manuals+ clarified question
    Question

    How do I remove the lower octave key on the Yamaha YDS-150?

    Answer

    The Yamaha YDS-150 Digital Saxophone is not designed to have its keys removed by the user. The manual specifically warns: "Do not open the instrument or attempt to disassemble or modify the internal components in any way."

    Attempting to remove a key could damage the internal sensors and will likely void your warranty. If you are frequently pressing the lower octave key by mistake, you may want to consider the following alternatives:

    • Adjust your thumb position: Ensure your left thumb is resting comfortably on the thumb rest and only moves slightly to engage the octave keys.
    • Use the YDS Controller App: While you cannot physically remove the key, you can use the dedicated smartphone app to customize settings, though there is no standard setting to "disable" a specific physical key's input.
    • Consult a Professional: If the key feels loose or overly sensitive, contact a qualified Yamaha service center for inspection rather than attempting a manual removal.
    1. Below key is the low A key, not the octave key
      Unter Taste ist die Tief-A-Taste, nicht die Oktav-Taste

      Lorenz asks <em>Below key is the low A key, not the octave key<e/em>
      Unter Taste ist die Tief-A-Taste, nicht die Oktav-Taste
      Manuals+ clarified question
      Question

      How do I remove the lower octave key on the Yamaha YDS-150?

      Answer

      Below key is the low A key, not the octave key
      Unter Taste ist die Tief-A-Taste, nicht die Oktav-Taste

  2. Is it possible to connect the speaker via bluetooth?
    불루투스로 스피커연결 가능 한가요?

    sang woong sim asks <em>Is it possible to connect the speaker via bluetooth?<e/em>
    불루투스로 스피커연결 가능 한가요?
    Manuals+ clarified question
    Question

    Is it possible to connect the Yamaha YDS-150 to a speaker via Bluetooth?

    Answer

    No, it is not possible to connect the Yamaha YDS-150 to a Bluetooth speaker or Bluetooth headphones for audio output. While the YDS-150 features Bluetooth, it is designed for Bluetooth Audio Input (to play along with music from a smartphone or tablet) and for connecting to the YDS Controller app.

    Because Bluetooth audio transmission involves a slight delay (latency), it is not suitable for real-time performance. To connect to an external speaker or headphones, you must use a wired connection via the PHONES/OUTPUT jack (3.5 mm stereo mini-jack) to ensure there is no lag between your playing and the sound output.

  3. When I connect to Bluetooth I am only offered connection to YDS 150 midi and not to YDS 150 Audio so I cannot feed a backing track through.
    Do I need to do a factory reset?

    Martyn Flower asks When I connect to Bluetooth I am only offered connection to YDS 150 midi and not to YDS 150 Audio so I cannot feed a backing track through.
    Do I need to do a factory reset?
    Manuals+ clarified question
    Question

    How do I connect to YDS-150 Audio via Bluetooth to play backing tracks, and is a factory reset necessary?

    Answer

    The Yamaha YDS-150 features two distinct Bluetooth functions: Bluetooth MIDI (for connecting to the YDS Controller app) and Bluetooth Audio (for streaming music/backing tracks through the instrument). If you only see the MIDI option, follow these steps to enable Audio pairing:

    • Enable Bluetooth Audio Pairing: Press and hold the [Fn] button and the [Eb] key (the lowest side key on the right hand) simultaneously. The display should indicate it is in pairing mode.
    • Check your Smart Device: Look for "YDS-150 Audio" in your smartphone or tablet's Bluetooth settings. Note that "YDS-150 MIDI" is handled within the app, while "YDS-150 Audio" must be paired via the system settings of your device.
    • Factory Reset: A factory reset is usually not required for this issue unless the Bluetooth module is unresponsive. To perform a factory reset if needed: Turn the power off. While holding the [1], [2], and [3] keys (the top three main keys), press the [Power] button to turn the unit on. The display will show "CLr" to confirm the reset.

    Note: Ensure "Airplane Mode" is off and that no other devices are currently hogging the Bluetooth Audio connection.

  4. The instrument makes a loud sound on A14, S12, T12, the rest of the sounds are quiet, how to increase the volume?
    Инструмент издает громкий звук на А14, S12, T12, остальные звуки тихие, как увеличить громкость?

    Борис asks <em>The instrument makes a loud sound on A14, S12, T12, the rest of the sounds are quiet, how to increase the volume?<e/em>
    Инструмент издает громкий звук на А14, S12, T12, остальные звуки тихие, как увеличить громкость?
    Manuals+ clarified question
    Question

    How can I increase the volume for specific voices on the Yamaha YDS-150, as some sounds like A14, S12, and T12 are loud while others are too quiet?

    Answer

    On the Yamaha YDS-150, individual voices (such as the Alto, Soprano, and Tenor presets you mentioned) may have different default volume levels. To adjust the volume and balance these sounds, you have two primary methods:

    • Master Volume: Use the [VOL +] and [VOL -] buttons on the instrument's control panel to adjust the overall output level.
    • YDS Controller App: For precise control over individual voice volumes, it is highly recommended to use the YDS Controller app (available for iOS and Android). This app allows you to edit specific voice parameters, including the volume for each preset, and save those changes to the instrument.
    • Breath Sensitivity: If some sounds feel too quiet, you may need to adjust the breath sensitivity settings. This can be done via the instrument's internal settings menu or more easily through the YDS Controller app to ensure the instrument responds correctly to your blowing pressure.

    If the volume remains inconsistent even after adjustment, ensure your firmware is up to date via the Yamaha support website.

  5. hello .. how to activate the half half and so half note of the yamaha yds 150 saxophone.
    please it is urgent.thank you
    bonjour .. comment activé la note mi demi et si demi du saxophone yamaha yds 150.
    s’il vous plaît c’est urgent.merci

    Ben Achour Aymen asks <em>hello .. how to activate the half half and so half note of the yamaha yds 150 saxophone.
    please it is urgent.thank you
    bonjour .. comment activé la note mi demi et si demi du saxophone yamaha yds 150.
    s'il vous plaît c'est urgent.merci
    Manuals+ clarified question
    Question

    How do I play E-half and B-half notes on the Yamaha YDS-150 digital saxophone?

    Answer

    The Yamaha YDS-150 Digital Saxophone is designed to follow standard saxophone fingering. To play non-standard notes like "half-notes" (microtones), you have two primary options:

    • YDS Controller App: You can use the dedicated YDS Controller app (available for iOS and Android) to customize your fingering. The app allows you to create and save custom fingering assignments, which can be used to map specific key combinations to microtonal pitches if the internal sound engine supports them.
    • Standard Fingering: Ensure you are using the standard saxophone fingering chart provided in the full owner's manual. For standard accidentals (sharps/flats), use the side keys or the pinky keys (Eb, C#, etc.) as you would on an acoustic saxophone.

    If you are referring to specific microtonal adjustments not found in standard fingering, please check the Fingering Customization section within the YDS Controller app, as the physical instrument does not have a dedicated "half-note" toggle switch.

  6. How do I press the keys to make them more or less sensitive to touch, I notice that sometimes I press the E natural key and the sound doesn’t come out perfect, sometimes it seems that I have to blow harder for the sound to come out, know that there is a regulation for the keys
    Como faço para ao apertar as teclas deixar elas mais ou menos sensíveis ao toque, percebo que as vezes aperto a chave do mi natural e o som nao sai perfeito, as vezes pareçe que tenho que soprar mais forte para o som sair, fique sabendo que existe uma regulagem para as teclas

    Helcio Manfredi asks <em>How do I press the keys to make them more or less sensitive to touch, I notice that sometimes I press the E natural key and the sound doesn't come out perfect, sometimes it seems that I have to blow harder for the sound to come out, know that there is a regulation for the keys
    Como faço para ao apertar as teclas deixar elas mais ou menos sensíveis ao toque, percebo que as vezes aperto a chave do mi natural e o som nao sai perfeito, as vezes pareçe que tenho que soprar mais forte para o som sair, fique sabendo que existe uma regulagem para as teclas
    Manuals+ clarified question
    Question

    How do I adjust the key sensitivity and breath response on the Yamaha YDS-150?

    Answer

    To address issues with key sensitivity and the amount of breath required to produce sound on your Yamaha YDS-150, you should use the YDS Controller app (available for iOS and Android). While the physical keys themselves do not have mechanical tension adjustments, the digital response can be customized:

    • Breath Sensitivity: Within the YDS Controller app, you can adjust the "Breath Resistance" and "Breath Response" settings. If you feel you have to blow too hard, lowering the threshold or adjusting the response curve will allow sound to trigger with less effort.
    • Key Response: The app allows you to adjust the Key Response settings to prevent "ghost notes" or delays. If a specific key like E natural is not responding correctly, ensure there is no debris under the key and check the app's settings to see if the key timing or sensitivity needs calibration.
    • Mouthpiece Check: Ensure the mouthpiece and reed are correctly seated. Even though it is a digital instrument, the breath sensor relies on the airflow through the mouthpiece assembly.

    If the E natural key physically feels different or stuck compared to others, it may require inspection by a qualified Yamaha service technician, as the manual warns against attempting to disassemble the internal components yourself.

  7. I think there should be a tutorial on YT explaining in Portuguese how to operate the instrument, including all the adjustment functions via bluetooth, wireless connections, etc. For example, I couldn’t connect and play sound from the YDS on a JBL flip 5 bluetooth box. I tried a signal emission adapter, but it worked with a big delay. Now I’m going to try another speaker via P2 cable. So, if there were any workshops, videos, tutorials, etc. to provide guidance on all the possibilities for using the instrument, it would be very useful.
    acho que deveria ter um tutorial pelo YT orientando em portugues o funcionamento do instrumento como todas as funções de ajuste pelo bluetooth, conexões sem fio, etc. Por exemplo, não consegui conectar e reproduzir o som do YDS numa caixa bluetooth JBL flip 5. Tentei um adaptador de emissão de sinal, mas funcionou com um delay grande. Agora vou experimentar outra caixa de som via cabo P2. Então, se tivesse algum workshop, video, tutorial, etc, para orientar sobre todas as possibilidades de utilização do instrumento, seria de muita utilidade.

    Marco antonio Tobaja asks <em>I think there should be a tutorial on YT explaining in Portuguese how to operate the instrument, including all the adjustment functions via bluetooth, wireless connections, etc. For example, I couldn't connect and play sound from the YDS on a JBL flip 5 bluetooth box. I tried a signal emission adapter, but it worked with a big delay. Now I'm going to try another speaker via P2 cable. So, if there were any workshops, videos, tutorials, etc. to provide guidance on all the possibilities for using the instrument, it would be very useful.
    acho que deveria ter um tutorial pelo YT orientando em portugues o funcionamento do instrumento como todas as funções de ajuste pelo bluetooth, conexões sem fio, etc. Por exemplo, não consegui conectar e reproduzir o som do YDS numa caixa bluetooth JBL flip 5. Tentei um adaptador de emissão de sinal, mas funcionou com um delay grande. Agora vou experimentar outra caixa de som via cabo P2. Então, se tivesse algum workshop, video, tutorial, etc, para orientar sobre todas as possibilidades de utilização do instrumento, seria de muita utilidade.
    Manuals+ clarified question
    Question

    How do I connect the Yamaha YDS-150 to a Bluetooth speaker, and why is there a delay when using wireless adapters?

    Answer

    Regarding your connection issues with the Yamaha YDS-150, there are two important technical distinctions to understand:

    • Bluetooth Audio Input vs. Output: The YDS-150 features Bluetooth input capability. This allows you to stream audio from a smartphone or tablet into the saxophone so you can play along with backing tracks through the instrument's speakers or headphones. It is not designed to send (output) wireless audio directly to Bluetooth speakers like the JBL Flip 5.
    • Latency (Delay): Using third-party Bluetooth transmitters (signal emission adapters) often results in significant audio lag. This is a common limitation of standard Bluetooth technology, which is generally too slow for real-time musical performance.

    Recommended Solutions:

    • Wired Connection (Best): As you mentioned, using a P2 (3.5mm) stereo mini-jack cable from the YDS-150's PHONES jack to the AUX input of your speaker is the best way to eliminate delay and ensure high-quality sound.
    • YDS Controller App: To adjust instrument functions via Bluetooth, ensure you are using the YDS Controller app on your smartphone. This connection is for data/settings only, not for wireless audio transmission.

    For official Yamaha tutorials in Portuguese, we recommend checking the Yamaha Musical BR YouTube channel, as they occasionally provide localized workshops and product demonstrations.

  8. What would be the ideal cable to connect the instrument to the soundboard?
    XLR x P2 (Stereo x Mono)
    P10 x P2 (Stereo x Mono)
    Qual seria o cabo ideal para ligar o instrumento à mesa de som?
    XLR x P2 (Stéreo x mono)
    P10 x P2 (Stéreo x mono)

    Glauber Oliveira asks <em>What would be the ideal cable to connect the instrument to the soundboard?
    XLR x P2 (Stereo x Mono)
    P10 x P2 (Stereo x Mono)
    Qual seria o cabo ideal para ligar o instrumento à mesa de som?
    XLR x P2 (Stéreo x mono)
    P10 x P2 (Stéreo x mono)
    Manuals+ clarified question
    Question

    What is the ideal cable to connect the Yamaha YDS-150 to a soundboard?

    Answer

    To connect the Yamaha YDS-150 to a soundboard or mixing console, you should use the PHONES/OUTPUT jack located on the instrument. This jack is a stereo mini-phone jack (3.5mm or P2).

    The ideal cable depends on your soundboard's inputs:

    • For a standard mixer channel (P10/TRS): Use a 3.5mm (P2) Stereo to Dual 1/4" (P10) Mono TS cable (often called a 'Y-cable' or 'breakout cable'). This allows you to output the stereo signal from the saxophone into two separate channels or a stereo input on the board.
    • For a single Mono channel: You can use a 3.5mm to 1/4" cable, but note that you may lose some of the stereo imaging of the internal voices.
    • XLR Connections: If you must use an XLR input on a soundboard, it is recommended to use a Stereo DI Box. Connect the YDS-150 to the DI box using a 3.5mm to dual 1/4" cable, and then run standard XLR cables from the DI box to the soundboard. This ensures the signal is balanced and protected over long distances.

    Note: Always ensure the volume on both the YDS-150 and the soundboard is turned down before connecting to prevent loud pops or damage to equipment.

  9. Good morning.
    Is there anyone who has good experience in using the YDS 150, who can guide, and who can also teach the tricks of digitizing the notes that can be done in more than one way, I have some ease of taking it by ear, but I understand some notes are more difficult to do, and I wish I had someone who could guide me.
    Bom dia.
    Existe alguém que tenha boa experiência na utilização do YDS 150, que possa orientar, e que também possa ensinar os macetes de digitalização das notas que possam ser feitas de mais de uma maneira, tenho alguma facilidade de tirar de ouvido, mas percebo algumas algumas notas são mais difíceis de fazer, e gostaria de ter alguém que pudesse me orientar.

    HÉLCIO MANFREDI. asks <em>Good morning.
    Is there anyone who has good experience in using the YDS 150, who can guide, and who can also teach the tricks of digitizing the notes that can be done in more than one way, I have some ease of taking it by ear, but I understand some notes are more difficult to do, and I wish I had someone who could guide me.
    Bom dia.
    Existe alguém que tenha boa experiência na utilização do YDS 150, que possa orientar, e que também possa ensinar os macetes de digitalização das notas que possam ser feitas de mais de uma maneira, tenho alguma facilidade de tirar de ouvido, mas percebo algumas algumas notas são mais difíceis de fazer, e gostaria de ter alguém que pudesse me orientar.
    Manuals+ clarified question
    Question

    How can I learn different fingering techniques and tricks for the Yamaha YDS-150?

    Answer

    The Yamaha YDS-150 is designed to mimic the fingering of an acoustic saxophone, but it also offers flexibility through digital customization. To master the "tricks" of digitizing notes and alternative fingerings, consider the following resources provided by Yamaha:

    • YDS Controller App: This is the most powerful tool for your request. By connecting your YDS-150 to a smartphone or tablet via Bluetooth, you can use the app to customize fingering. This allows you to create your own "tricks" or alternative fingerings for notes that you find difficult to play with standard saxophone technique.
    • Fingering Chart: The full instruction manual includes a comprehensive fingering chart. While the YDS-150 supports standard saxophone fingerings (including high F# and front F), the digital nature of the instrument means you can often use simplified fingerings depending on the settings in the app.
    • Breath Sensitivity: Since you mentioned playing by ear, you may find some notes "difficult" because of how the sensor responds. You can adjust the breath resistance and response in the YDS Controller app to make the instrument feel more natural to your playing style.

    For personalized guidance, Yamaha often provides video tutorials on their official YouTube channel specifically for the YDS series, which demonstrate how to utilize the app for custom fingering layouts.

  10. Utilizzo Notation Composer per scrivere gli spartiti ma non riesco tramite USB a fara riconoscere al programma lo strumento come Midi controller. Cosa devo fare? Grazie

    Roberto asks Utilizzo Notation Composer per scrivere gli spartiti ma non riesco tramite USB a fara riconoscere al programma lo strumento come Midi controller. Cosa devo fare? Grazie
    Manuals+ clarified question
    Question

    How do I connect the Yamaha YDS-150 to a computer via USB to use it as a MIDI controller with notation software?

    Answer

    To use your Yamaha YDS-150 as a MIDI controller with software like Notation Composer via USB, please follow these steps:

    • Use a Data-Compatible Cable: Ensure you are using a USB cable that supports data transfer, not just charging. Connect the micro USB port on the instrument to your computer.
    • Power Source: If you are using the USB port for both power and MIDI, ensure your computer's USB port provides sufficient power. If the instrument does not turn on, you may need to use batteries while the USB is connected for data.
    • Driver Installation: On most modern operating systems (Windows 10/11 and macOS), the YDS-150 is "class-compliant," meaning it should be recognized automatically without a manual driver installation. However, if it is not appearing, check your computer's Device Manager (Windows) or Audio MIDI Setup (Mac) to see if "YDS-150" is listed.
    • Software Configuration: Open Notation Composer and go to the MIDI setup or Device settings menu. You must manually select the YDS-150 as the Input Device for the software to receive signals from the instrument.
    • MIDI Channels: Ensure the instrument and the software are communicating on the same MIDI channel (usually Channel 1 by default).

    If the device is still not recognized, try a different USB port on your computer or a different USB cable to rule out hardware connectivity issues.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.