OVS Bed Extension

Quick Setup & Use
- Read before use: Do not use impact tools or overtighten.
- Assemble side rails first: Slide 4 T-nuts into the left/right channels; loosely align and install 4 button head bolts to each side. Repeat for the opposite side.
- Assemble rear channel: Insert 3 T-nuts into the rear channel slide; loosely install 3 button head bolts. Add 4 corner button head bolts to secure side and rear plates together; use provided hex nuts on the inner side. Then tighten all button head bolts once all are in position.
- Anchor point placement: Slide a T-nut into the channel, screw in the anchor point loosely, move to the desired position, and tighten. Leave ~2–3 inches between the square nut insertion section and the ratchet strap insertion section (weak points that can peel under too much pressure). Apply strap pressure to the cargo load (not entirely the anchor points) and tighten straps at a slight angle.
- Positioning: With another person, slide the bed extension onto the truck bed centered between wheel wells. Leave a minimum of 1 1/2 inch clearance from the bulkhead. Close the tailgate and confirm clearance, then reopen and reconfirm measurements.
- Drill & install rivet nuts: Align drill holes to truck ridges and mark holes. Remove the bed extension, reconfirm markings, and drill based on bed type (steel vs composite/aluminum) using the specified drill bits. Insert the correct rivet nuts using the provided rivet nut tool.
- Final mounting: Place rivet nuts onto the tray, insert M8 oversized washers and M8 x 1.25 hex head bolts loosely, then tighten after all bolts are inserted.
GET TO KNOW YOUR BED EXTENSION
Parts List
- 1x Left Side Frame
- 1x Right Side Frame
- 1x Rear Frame
- 16x Button Head Bolts
- 1x T Nuts
- 4x Hex Nuts
- 8x M8 Oversized Washers
- 8x M8 x 1.25 Hex Head Bolts
- 8x M8 x 1.25 Rivetnuts (Composite/Aluminum)
- 8x M8 x 1.25 Rivetnuts (Steel)
- 1x M8 x 1.25 Rivetnut Tool
Tools Needed
- 1x Tape Measure
- 1x Allen Key
- 1x Drill
- 1x 1/2″ Drill Bit
- 1x 7/32″ or 13.5 mm Drill Bit
- 1x 13mm Wrench
- 1x 22mm Wrench
- 1x 17mm Wrench
Assembly Instructions
BED SIDE RAIL ASSEMBLY
We recommend assembling side rails before truck bed installation.
- To begin, slide in the 4 provided T Nuts into the left or right channels.
- Align the left or right plate to the T Nuts and loosely install the 4 button head bolts through the plate to the T Nuts.
- NOTE: Do Not Tighten.
- Repeat for opposite side.
- Next, slide in the 3 provided T Nuts to the rear channel slide rail.
- Align the rear plate to the T Nuts and loosely install the 3 button head bolts through the plate to the T Nuts in the rear channel slide.
- Once loosely installed, insert 4 button head bolts on the corners to secure the side and rear plates together.
- Use the provided M6 hex nuts to secure on the inner side.
- When all bolts are in position, tighten all button head bolts to T-nuts.

Bed Extension
SET-UP & CARE INSTRUCTIONS
DO NOT USE IMPACT TOOLS OR OVERTIGHTEN* Before drilling holes for Plusnut installations, ensure there are no fuel lines, fuel tanks, batteries, wires, or other obstructions underneath the vehicle that could be damaged in the drilling process.
- Slide in the T Nut to the channel.
- Screw in the Anchor Points loosely.
- Move the Anchor Point to your desired position and tighten to secure. Unscrew to change position depending on cargo.

- Make sure to create some distance between the square nut insertion section before tightening your anchor point and ratchet strapping, as these are weak points that can start to peel when ratcheting with too much pressure.
- It is recommended to leave about 2-3 inches of space between your anchor point and this insertion section

- When using the ratchet straps on the anchor points, please ensure the pressure of the strap is being applied to the cargo load and not entirely on the anchor points. Straps should be tightened at a slight angle as the channels may begin to peel inward.

- With the help of another person, slide the Bed Extension onto the truck bed directly in the center of the bed. Align and center Bed Extension evenly between wheel wells and leave a minimum of 11/2″ of clearance between the bulkhead.
- Close the tailgate and make sure there is adequate clearance.
- NOTE: The clearance distance between the bulkhead and the tailgate will be unique to the make and model of the vehicle. The distance spans from 3/16″-11/2″ Open tailgate and reconfirm measurements.
- Align drill holes to the ridges of your truck.
- Mark all drill holes onto the ridges of the truck.
- Reconfirm drill markings before the next step.
- Remove the bed extension from the truck bed in order to drill all marked holes.


- NOTE: Determine what type of bed you have.
- Steel Truck Bed: If you have a steel bed, insert the provided Rivetnuts into the drill holes. Use a 17/32 (13mm) Drill Bit.

- Composite/Aluminum Truck Bed: If you have a Com- posite/Aluminum Bed use the provided Rivetnuts into the drill holes. Use a 1/2″ Drill Bit.

- The Rivet Nut hand tool is comprised of 3 parts.
- Upper Body (the smaller body piece)
- Lower Body
- Socket Head Cap Screw
- Put the socket head cap screw through tool in the orientation shown in the picture. Then thread rivet nut on the screw until it rests against the underside of the bottom.
- Insert rivet nut in hole of application while threaded on tool. Use 7/8″ Wrench to keep bottom body from turning. Next, put a 11/16″ socket over the body turn it clockwise. It will thread top body out of the bottom body. This lifts on the threads of rivet nut, and collapses it. This forms a bubble on the backside holding the rivet nut. Continue turning the wrench until it stops. Reverse the socket to break the tension in tool. Remove the socket and thread screw out installed rivet nut. Screw top body in bottom before installing.

- Once the Rivet Nuts are placed onto the tray, insert M8 oversized washers and M8 x 1.25 Hex Head Bolts loosely, then tighten once all bolts are inserted.

- It is possible to install directly to a Decked Drawer System, but you would need to use the shorter nutserts with the shorter M8 hardware so that the hardware does not interfere with the drawer’s functions.

CLEANING
- Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Bed Extension
STORING
- Store in a cool and dry area when not in use.
PAYLOAD
- This Bed Extension is only able to carry 1250 LBS.
WARNING
- IT IS ESSENTIAL THAT ALL OVERLAND VEHICLE SYSTEMS PRODUCTS ARE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
- FAILURE TO DO SO MAY LEAD TO AN AUTOMOBILE ACCIDENT, RESULTING IN SERIOUS INJURY OR DEATH.
- YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL OVERLAND VEHICLE SYSTEMS PRODUCTS TO YOUR VEHICLE, REGULARLY CHECKING ATTACHMENTS BEFORE USE, AND PERIODICALLY INSPECTING FOR WEAR, DAMAGE, OR NECESSARY ADJUSTMENTS.
- IT IS CRITICAL THAT YOU READ AND FULLY UNDERSTAND ALL INSTRUCTIONS AND SAFETY PRECAUTIONS PROVIDED WITH YOUR OVERLAND VEHICLE SYSTEMS PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT FULLY COMPREHEND THE INSTRUCTIONS OR LACK MECHANICAL EXPERIENCE, IT IS STRONGLY RECOMMENDED THAT YOU SEEK ASSISTANCE FROM A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL OVERLAND VEHICLE SYSTEMS IS NOT RESPONSIBLE FOR ANY DAMAGE RESULTING FROM IMPROPER INSTALLATION OF THE PRODUCT. IF YOU HAVE QUESTIONS REGARDING INSTALLATION, PLEASE CONTACT US FOR ASSISTANCE.
- BEFORE DRILLING HOLES FOR PLUSNUT INSTALLATIONS, ENSURE THERE ARE NO FUEL LINES, FUEL TANKS, BATTERIES, WIRES, OR OTHER OBSTRUCTIONS UNDERNEATH THE VEHICLE THAT COULD BE DAMAGED IN THE DRILLING PROCESS.
- DO NOT INSTALL ON BED LINER OR BED MAT.
Troubleshooting
- Rivet nut/installation alignment issues: Reconfirm drill markings before drilling. Remove the bed extension to drill all marked holes.
- Anchor point/ratchet strap concerns: Ensure there is about 2–3 inches of space between the anchor point and the square nut insertion section. Tighten straps so pressure is applied to the cargo load rather than entirely on the anchor points, and tighten at a slight angle to reduce channel peeling.
- Fit/clearance problems: Center the bed extension evenly between wheel wells and leave a minimum 1 1/2 inch clearance from the bulkhead. Clearance between bulkhead and tailgate varies by vehicle make/model—measure and reconfirm after closing the tailgate.
- Hardware doesn’t seat correctly: Ensure rivet nuts are selected for the correct bed type (Steel vs Composite/Aluminum) and drilled using the corresponding drill bit size.
CONTACT
- CUSTOMER SUPPORT 833-226-4863
- SALES@OVERLANDVEHICLESYSTEMS.COM
Documents / Resources
![]() | Bed Extension |
References
- User Manualmanual.tools
Published: July 23, 2026
Updated: July 24, 2026

