RuoShui 668A Wire Tracker User Manual

RuoShui-logo

RuoShui 668A Wire Tracker

RuoShui-668A-Wire-Tracker-product

Specifications

  • Transmitter: 1pc
  • Receiver: 1pc
  • User’s Manual: 1pc
  • Battery: 9V (1pc), 1.5V AAA (3pcs)
  • RJ-11 Fit Line: 1pc
  • RJ-45 Fit Line: 1pc
  • Alligator Clipper Fit Line: 1pc
  • Headset: 1 pair
  • Functions: Line search (SCAN), Cable proofreading (TEST), Line voltage test (VOLT), Continuity test (OHM), Torch function, Adjustable sensitivity, Headset function, Frequency conversion of line signal
  • Current: Transmit current 45mA, Receive current 100mA

Safety Information

Warning
To avoid electric shock or personal injury, please follow these guidelines:

  1. Do not directly search for cables that have been connected with strong electricity (such as electrical wires in your house). Otherwise, personal injury and equipment damage may occur.
  2. Pay attention to the thunder and lightning when you use the instrument in rainy days, in order to avoid the personal injury and equipment damage caused by the thunder and lightning.
  3. If the POWER indicator of the wire tracker is blinking, the battery voltage is low, please replace the battery.
  4. If you do not use this product for a long time, please take out the battery to avoid battery leakage and corrosion of the battery shelf, which may cause poor contact
  5. If there is something wrong with the instrument, please ask professionals to repair it, do not open the shell privately.

THEORY

Connect the voice signal emitted by the hunt signal generator to the terminal of the target cable through the RJ 45/RJ11 general interface to generate a surround audio signal field around the target cable loop. A high sensitivity induction wire tracker is used to identify the signal which it sends along and at the end of the loop, so that you can find the target cable.

THE COMPONENT OF PRODUCT

  1. Transmitter 1pc
  2. Receiver 1pc
  3. User’s manual 1pc
  4. Battery: 9V 1pc; 1.5V AAA*3
  5. RJ-11 fit line 1pc; RJ-45 fit line 1pc
  6. Alligator clipper fit line 1pc
  7. Headset 1 pair

OPERATION

Line search (SCAN) Find out the desired cable from a large number of cables.
Cable proofreading (TEST) Fast measurement of open circuit, short circuit, sequence.
Line voltage test (VOLT) Measuring the working voltage and positive or negative of phone line.
Continuity test (OHM) Checking the phone which is under open circuit or short circuit.

( Phone line isn’t connected to any live equipment)

Torch function Super bright and white light torch function
Adjustable sensitivity The volume can be adjusted according to your need when using it.
Headset function In noisy occasions, headphones can be worn to work.
Frequency conversion of line signal You can set different frequencies to find lines.

Weak current-turn on test:Can be connected to the Phone line / Ethernet switch/ Router/ Line hunting when the PC terminal is power on. The measured voltage  should not exceed 48V.

Description of the wire tracker

The product shall prevail in kind, subject to change without notice

RuoShui-668A-Wire-Tracker-fig- (1)

1. POWER switch
2. SCAN line hunting function switch, frequency conversion switch
3. V line voltage function switch
4. OHM continuity test function switch
5. TEST line searching switch, the speed selection of line searching
6. Function indicator light
7. RJ11/RJ45 connecting terminal
8. SCAN  line hunting key
9. Volume adjustable dial
10. Torch switch
11. Location of torch light
12. Line hunting signal inductor
13. Line hunting light area
14. RJ45 Line hunting socket

LINE HUNTING FUNCTION (SCAN)

The line hunting function of the product is to quickly find out the desired pair of lines in a large number of lines. Connect one end of the line to be tested (such as network cable, telephone line, video signal cable)to the RJ-11,RJ-45 socket of the transmitter, turn on the transmitter, press the SCAN button, the SCAN light of the product turns on, and the product enters the tracing signal transmitting state. Connect the end of the line to be located. Press the SCAN button, listen to the “beep” sound horn around the receiver which is at the other end to be tested (line terminal, for example, the telephone system distribution frame, junction box, the computer network hub side), comparing “beep” sound volume, the loudest pair is the correct pair of lines. In a noisy environment, if the “beep” sound is not obvious, press Hz on the transmitter to switch the frequency of the hunt signal, so as to confirm whether the received sound is the hunt signal sound or noise. AS shown in the figure below: Figure 3 connecting the target line, Figure 4 searching in the wire harness, Figure 5 finding the target line. If the target line already has the crystal head, you can connect the crystal head directly into the RJ11 or RJ45.

  1. Insert the target line to RJ45 jack.
  2. Change line hunting function.
  3. Clamp the target line with alligator clipper.
  4. Use the receiver to find the target line in the wire harness.
  5. The loudest line is the target line.RuoShui-668A-Wire-Tracker-fig- (2)

LINE HUNTING FUNCTION (TEST)

Using the function of the line hunting, the basic physical connection characteristics such as open circuit, short circuit and line sequence can be tested quickly.

  1. Using IEEE10Base-T, EIA/TIA568A, EIA/EIA568B, AT&T258A, Token-Ring standard UTP computer network line;
  2. 2-core, 4-core telephone line;
  3. Any other metal connecting line. Connect one end of the line under test to the RJ-45 socket of the transmitter. When you press the TEST button of the transmitter, the OHM indicator is on and the SCAN indicator is blinking, indicating that the cable hunting function of the transmitter is working properly. Connect the other end of the line, which is to be measured, into the RJ-45 socket of the receiver, according to the status of the 8 lines indicator on the receiver (1、2、3、4、5、6、7 、8) to check the circuit is good or not, the measurement result is clear.RuoShui-668A-Wire-Tracker-fig- (3)

LINE VOLTAGE TEST (VOLT)

The line status test function can measure the state of the line, including the presence or absence of voltage, and voltage positive and negative. Only the transmitter is needed to complete the line state measurement. Insert the alligator clipper fit line to RJ-11 socket, red and black line clamps the circuit under test, if the phone line has a voltage indicator light will on, otherwise it won’t light up. Or directly insert the phone line that has been connected to RJ-11 into RJ-11 interface, and also measure whether there is DCV and positive and negative indication on the line. The figure below is used to measure that whether the phone line has DCV.
Note: Do not use it to measure ACV and other high voltage circuits. Otherwise, electric shock hazard may occur

  1. Insert the phone line to RJ-11 socket.
  2. If the transmitter light SCAN or OHM is on, indicating the phone line has DCV. RuoShui-668A-Wire-Tracker-fig- (4)

Positive and negative indicate:

  1. Transmitter SCAN light indicates that the red clip is holding the positive electrode of the battery.
  2. Transmitter OHM light indicates that the red clip is holding the negative electrode of the battery. RuoShui-668A-Wire-Tracker-fig- (5)

CONTINUITY TEST FUNCTION (OHM)

The line continuity test is used to measure whether the phone line is under short circuit or not when it is not connected to the phone network. Before the test, it is necessary to measure whether the telephone line has voltage. If there is voltage indication, the line is working. At this time, making the continuity test, and the short circuit indicator SCAN will be light on, this is normal, because the tester forms a closed circuit with the circuit.Insert one end of the crocodile adaptor line into the RJ-11socket of the transmitter, and clamp the line to be tested with red and black clamps respectively. If the line is under short circuit, the SCAN indicator of the transmitter will be light on. The telephone line which has been fixed with the crystal head can be measured by directly inserting the RJ-11 port of the transmitter, and making the continuity test of other uncharged lines by clamping the line to be measured with the alligator clips adapter line.

  1. Short circuit、open circuit measurement.RuoShui-668A-Wire-Tracker-fig- (6)

ELECTRIC STATIC CHARACTERISTIC

  • Current transmit current≤45mA, receive current≤100mA
  • Battery receiver 9V battery; transmitter AA 1.5V battery *3
  • Transmission distance of hunting line ≥3km
  • Safety safe to use (the probe can directly contact the exposed metal wire)

FAULT DIAGNOSIS

Model Symptoms Problem Solution
 

Transmitter

Press POWER key, the light isn’t working The battery is exhausted or not installed. Replace a qualified battery
POWER light flashing Battery low voltage Replace a qualified battery
 

 

Receiver

 

Press SCAN, there’s no audio sound when hunting line.

The battery is exhausted or not installed. Replace a qualified battery
Target line too far, hunting line signal is not transmitted. Close to the target or transmitting terminal of hunting line, heard the sound of searching, confirm the function is

normal.

TECHNICAL INDICATORS

Hunting line function √
Paired function √
Continuity test of short circuit √
Line voltage √
Sensitivity adjustable √
Torch √
Display LED light
Distance of hunting line 3 km
Output signal level Approx 23Vp-p (frequency adjustable)
Other function Energy saving design, sensitivity adjustable, low voltage detection, headset function.
Packing Color box ; tool bag

Documents / Resources

PDF thumbnail668A Wire Tracker
User Manual · 668A Wire Tracker, 668A, Wire Tracker, 668A Tracker

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.