3DeVOK Airgo Wireless Handle

Specifications
- Primary Network Card (Handle): BrosTrend AC1200 WiFi Adapter (or similar AC1200 compatible adapter)
- Receiver (Computer): TP-Link Archer T3U AC1300 WiFi Adapter (or similar AC1300 compatible adapter)
- Wireless Standard: Wi-Fi (802.11ac recommended)
- Handle Connection Port: USB 3.0
- Computer Connection Port: USB 3.0
- Scanner Connection Port: TYPE-C
- Handle Power: Battery-operated
- Default WiFi Password: 12345678
- Scanner WiFi Naming Convention (MT device): 3DeVOK_SK03IU0HXXXX (XXXX = last four digits of scanner serial number)
- Scanner WiFi Naming Convention (MQ device): 3DeVOK_SK03IU0GXXXX (XXXX = last four digits of scanner serial number)
Wireless Handle Configuration
Note: A wired connection is required for the initial wireless setup of the scanner. Please ensure your device is properly connected to your computer. Check the Quick Guide file attached in the USB drive for operation. The detailed wireless connection steps are as follows:
Network Card Connection
(with Brosrrend AC1200 WiFi Adapter and TP-Link Archer T3U AC1300 WiFi Adapter as an example)
- Following the successful establishment of a wired connection to the scanner, the network card must be configured within the 3DeVOK Studio software. Click the
icon in the lower-left corner of the software to enter the connection settings, as shown in Figure I-I.
- Select “WiFi Network Card” in the Connection Mode. Click “OK” to confirm, as shown in Figure 1-2.

Usage Instructions
After completing the WiFi Network Card setup, proceed with the assembly and wireless connection of the handle. The assembly and connection steps are as follows:
- Insert the BrosTrend AC1200 WiFi Adapter (hereinafter referred to as the Primary Network Card) into the USB 3.0 port at the bottom of the wireless handle. Then, insert the TP-Link Archer T31J AC1300 WiFi Adapter (hereinafter referred to asthe Receiver) into a USB 3.0 on the computer, as shown in Figure 2-1.
- Insert the battery into the battery compartment of the handle and close the protective cover.
- Remove the threaded hole protective cover from the scanner, align the screw on the wireless handle bracket with the threaded hole, and hand-tighten the screw to ensure a secure, as shown in Figure 2-2 (①).
- Insert the network card into the slot at the bottom of the handle, as shown in Figure 2-2 (②).

- Insert the data cable of handle into the TYPE-C port at the rear of the wireless handle, and remove the wired cable atthe rear of the scanner. Then, connect the data cable of handle to the TYPE-C port of scanner, and tighten the screw.
- Long press the power button of the handle to turn it on.
- Import the WiFi password, which shall be “12345678”.

- Wait for the middle indicator light on the light strip to change from blinking blue to steady blue, and then to steadygreen, indicating a successful wireless connection.
- Click the system tray icon, select “WLAN2” (or “WLAN3” on some computers, which may vary). Find the WiFi named3DeVOK_SK03IU0HXXXX (where XXXX represents the last four digits of the currently connected scanner’s serial number),then click “Connect”, as shown in Figure 2-3.
- The overall connection of wireless handle – network card solution is shown in Figure 2-4.

Note:
- 3DeVOK_SK03IU0HXXXX indicates the connected device is MT.
- For the MQ device, the WiFi name shall be “3DeVOK_SK03IU0GXXXX”.
- To switch the network card connection between multiple devices, the following steps are mandatory:
- Establish a wired connection to the new device;
- Redeploy the network adapter configuration;
- Reconnect to the W
Troubleshooting
- No WiFi Network Found:
- Ensure both the Primary Network Card (in the handle) and the Receiver (in the computer) are properly inserted into USB 3.0 ports.
- Verify the handle is powered on (long-press the power button).
- Check if the network card configuration was successfully applied in the 3DeVOK Studio software.
- Try restarting the computer and the scanner handle.
- Unable to Connect to WiFi (Incorrect Password):
- Double-check the WiFi password. It is
12345678. - Ensure you are selecting the correct WiFi network name (
3DeVOK_SK03IU0HXXXXor3DeVOK_SK03IU0GXXXX) corresponding to your scanner’s serial number.
- Double-check the WiFi password. It is
- Indicator Light Not Turning Green:
- If the light remains blinking blue or steady blue, the connection is not yet established.
- Re-verify all connection steps, especially the WiFi password and network selection.
- Ensure there are no strong wireless interferences nearby.
- Try disconnecting and reconnecting the WiFi from your computer’s system tray.
- Scanner Not Responding After Wireless Connection:
- Confirm the indicator light on the handle is steady green.
- Check the 3DeVOK Studio software to see if the scanner is recognized.
- Ensure the data cable between the handle and the scanner is securely connected.
- If switching between multiple devices, ensure you have followed the “Switching Network Card Connection Between Multiple Devices” steps.
- “WLAN2” or “WLAN3” Not Visible in System Tray:
- Ensure the TP-Link Archer T3U AC1300 WiFi Adapter (Receiver) is correctly installed, and its drivers are up-to-date on your computer.
- Check your computer’s device manager to see if the WiFi adapter is recognized and functioning correctly.
Documents / Resources
![]() | Airgo Wireless Handle |
References
- User Manualmanual.tools
Published: June 17, 2026

