
INSTRUCTION MANUAL
Fire Pit Table (1 pc)


DANGER
FIRE OR EXPLOSION HAZARD
If you smell gas:
Shut off gas to the appliance.
Extinguish any open flame.
If odor continues, leave the area immediately.
After leaving the area, call your gas supplier or fire department.
Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.
WARNING
Do not store or use gasoline, or other flammable vapor sand liquids, in the vicinity of this or any other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING: For Outdoor Use Only
Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car or home.
WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
SAFETY INFORMATION
Read the instructions before installation and use.
– This appliance must be installed and the gas cylinder stored in accordance with the regulations in force;
– Do not obstruct the ventilation holes of the cylinder housing;
– Do not move the appliance when in operation;
– Shut off the valve at the gas cylinder or the regulator before moving the appliance;
– The tubing or the flexible hose must be changed within the prescribed intervals;
– Use only the type of gas and the type of cylinder specified by the manufacturer;
-Do not use the appliance in big wind weather. It is advisable to fit the dress guard available from the manufacturer. Failure to fit this dress guard will result in a potential hazard to clothing when approaching the appliance;
– The injector is installed by the manufacturer only. Do not connect the gas cylinder directly to the appliance without regulator. Use only the type of gas and the type of cylinder specified in the instructions;
– This appliance is intended for decorative purposes;
– Not for domestic use!
– These instructions are only valid if the country symbol appears on the instruction manual and on the appliance.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
DANGER
Failure to comply with the precautions and instructions provided with this fire pit can result in death, serious bodily injury and property loss or damage from hazards of fire, explosion, burn, asphyxiation, and/or carbon monoxide poisoning. Only persons who can under stand and follow the instructions should use or service this fire pit.
DANGER
FOR YOUR SAFETY
If you smell gas:
- Shut off gas to the appliance.
- Extinguish any open flame.
- If odor continues, keep away from the appliance and immediately call your gas supplier or fire department.
Solid fuels shall not be burned in this appliance.
DANGER
- EXPLOSION – FIRE HAZARD
- Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the fire pit as recommended by the instructions.
- Provide adequate clearances around air openings into the combustion chamber.
- Never use the fire pit in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
- During operation, this product can be a source of ignition. Keep fire pit area clear and free from combustible materials, gasoline, paint thinner, cleaning solvents and other flammable vapors and liquids. Do not use fire pit in areas with high dust content.
- Minimum fire pit clearances from combustible materials: two (2) feet from the sides & two (2) feet from the rear, 5 (5) feet from ceiling.
DANGER
- EXPLOSION – FIRE HAZARD
- Never store propane near high heat, open flames, pilot lights, direct sunlight, other ignition sources or where temperatures exceed 120 degrees F (49°C).
- Propane vapors are heavier than air and can accumulate in low places. If you smell gas, leave the area immediately.
- Never install or remove propane cylinder while fire pit is lighted, near flame, pilot lights, other ignition sources or while fire pit is hot to touch.
- This fire pit is red hot during use and can ignite flammables too close to the burner. Keep flammables at least 2 feet from sides & 2 feet from rear, 5 feet from ceiling. Keep gasoline and other flammable liquids and vapors well away from fire pit.
- Store the propane cylinder outdoors in a well ventilated space out of reach of children. Never store the propane cylinder in an enclosed area (house, garage, etc.). If fire pit is to be stored indoors, disconnect the propane cylinder for outdoor storage.
WARNING
We cannot foresee every use which may be made of our fire pit.
Check with your local fire safety authority if you have questions about fire pit use.
Other standards govern the use of fuel gases and heat producing products for specific uses. Your local authorities can advise you about these.
DANGER
CARBON MONOXIDE HAZARD
This fire pit is a combustion appliance. All combustion appliances produce carbon monoxide (CO) during the combustion process. This product is designed to produce extremely minute, non-hazardous amounts of CO if used and maintained in accordance with all warnings and instructions. Do not block air flow into or out of the fire pit.
Carbon Monoxide (CO) poisoning produces flu-like symptoms, watery eyes, headaches, dizziness, fatigue and possibly death. You can’t see it and you can’t smell it. It’s an invisible killer. If these symptoms are present during operation of this product get fresh air immediately!
For outdoor use only.
Never use inside house, or other unventilated or enclosed areas.
This fire pit consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life.
WARNING
WARNING indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
WARNING: For Outdoor Use Only
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent, car or home.
WARNING
Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operation and maintenance instructions thoroughly before installing or servicing this equipment.
WARNING
California Proposition 65
Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm.
WARNING
BURN HAZARD
- Never leave fire pit unattended when hot or in use.
- Keep out of reach of children.
WARNING
Certain materials or items, when stored under the fire pit, will be subjected to radiant heat and could be seriously damaged.
CAUTION
SERVICE SAFETY
Keep all connections and fittings clean. Make sure propane cylinder valve outlet is clean.
During set up, check all connections and fittings for leaks using soapy water. Never use a flame.
Use as a heating appliance only. Never alter in any way or use with any device.
CAUTION
CAUTION indicates an imminently hazardous situation which, if not avoided, may result in minor or moderate personal injury, or property damage.
WARNING
Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.
WARNING
- This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
- Propane gas is heavier than air and leaking propane will sink to the lowest level possible. It can ignite by ignition sources including matches, lighters, sparks or open flames of any kind many feet away from the original leak. Use only propane gas set up for vapor withdrawal.
- Store or use propane gas in compliance with local ordinances and codes or with ANS/NFPA 58. Turn off propane when not in use.
WARNING
- Alert children and adults to the hazards of high surface temperatures. Stay away from these surfaces to avoid burning skin or igniting clothing.
- Carefully supervise young children when in the vicinity of the fire pit.
- Do not hang clothing or any other flammable materials from the fire pit, or place on or near the fire pit.
- Replace any guard or protective device removed for servicing the appliance prior to placing back in service.
- Installation and repair should be done by a qualified service person. The fire pit should be inspected before use and annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and circulating air passageway of the appliance be kept clean.
WARNING
Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control that has been under water.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 minutes
Tools Required for Assembly (not included): Phillips screwdriver, Leak Detection

PACKAGE CONTENTS

HARDWARE

ASSEMBLY INSTRUCTIONS
Step 1
- Turn over the table top, attach Burner (G) to Table Top (A) using Bolts (H) and Nuts (L).

Step 2
- Attach Right Side Panel (B) and Left Side Panel (C) to Table Top (A) using Bolts (H) and Washer (K).
NOTE: Please do not fully tighten the bolts until unit is fully assembled. - Attach the control box to Side Panel (C) using Bolts (H) and tighten.

Step 3
- Attach Rear Panel (D) to Right Side Panel (B) and Left Side Panel (C) using Bolts (I) and Washer (K).

NOTE: Please do not fully tighten the bolts until unit is fully assembled.
Step 4
- Attach Gas Cylinder Base (E) to Right Side Panel (B) and Left Side Panel (C) using Bolts (J) and Washer (K).
- Fully tighten all bolts.

Step 5
- Attach Door (F) to the fire pit table.
NOTE: Please pour the glass Stones (M) into the burner at the this time and place them evenly.

Step 6
- Assemble Glass (S1) and (S2) together with Bracket (T1) and (T2) using Bolts (U). Attach Foot Pad (V) to Bracket (T2) using Bolt (W).

Step 7
- Put the cylinder (not included) into the Gas Cylinder Base (E), connect hose and regulator to the cylinder, fasten the cylinder with butterfly bolt.

The knob on the LP tank must be closed. Make sure that the knob is turned
clockwise to a full stop. The cylinder supply system must be arranged for vapor withdrawal. Check that the control knob on the control unit is turned off. Hold the regulator in one hand and insert the nipple into the valve outlet. Be sure the nipple is centered in the valve outlet. The coupling nut connects to the large outside threads on the valve outlet. Hand-tighten the coupling nut
clockwise until it comes to a full stop. Firmly tighten by hand only.
To Disconnect: Fully close the tank valve by turning
clockwise Turn the coupling nut
counterclockwise until the regulator assembly detaches.
The cylinder used must include a collar to protect the cylinder valve.
Never connect an unregulated propane cylinder to the heater. The appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2psi (3.5kPa). Other cylinders may be acceptable for use with the appliance provided they are compatible with the appliance retention means.
OPERATION INSTRUCTIONS
The propane gas and cylinder are sold separately. We suggest use this appliance with LPG cylinder of 5 kg. The maximum diameter and the maximum height of the cylinder is 380 mm and 450 mm as shown in (Fig. 1).
Use this heater only with a propane vapor withdrawal supply system. See chapter 5 of the standard for storage and handling of liquefied petroleum gas, ANS/NFPA 58.
Your local library or fire department should have this book.

Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance. A cylinder must be stored outdoors in a well-ventilated area out of the reach of children. A disconnected cylinder must have dust caps tightly installed and must not be stored in a building, garage or any other enclosed area.
The maximum inlet gas supply pressure: 250 psi /1750 kPa.
The minimum inlet gas supply pressure: 25 psi /175kPa.
Manifold pressure with regulator provided: 11 inch W.C/2.74 kPa.
The pressure regulator and hose assembly supplied with the appliance must be used. When an appliance is for connection to a fixed piping system, the installation must conform with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI Z223.1 NFPA 54; National Fuel Gas Code; Natural Gas and CSA B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable;
Properly locating the gas hose including locating the hose out of pathways where people may trip over it or in areas where the hose may be subject to accident all damage.
A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection.
The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
The cylinder must have a listed overfilling prevention device.
The cylinder must have a connection device compatible with the connection for the appliance.
HEATER STAND AND LOCATION
- The heater is primarily for outdoor use only. Always ensure that adequate fresh air ventilation is provided.
- Always maintain proper clearance to combustible materials, i.e. top 60 inches and sides 48 inches minimum.
- Heater must be placed on level firm ground.
- Never operate heater in an explosive atmosphere like in are as where gasoline or other flammable liquids or vapors are stored.

Leak Test
Gas connections on the heater are leak tested at the factory prior to shipment. A complete gas tightness check must be performed at the installation site due to possible mishandling in shipment or excessive pressure being applied to the heater.
WARNING
- Perform all leak tests outdoors.
- Extinguish all open flames.
- NEVER leak test when smoking.
- Do not use the fire pit until all connections have been leak tested and do not leak.

DANGER
NEVER USE A LIGHTER/FLAME TO CHECK FOR GAS LEAKS.
- Make 2-3 oz. of leak check solution (one part liquid dish washing detergent and three parts water).
- Apply several drops of solution where hose attaches to regulator.
- Apply several drops of solution where regulator connects to cylinder.
- Make sure all fire pit and light valves are OFF.
- Turn cylinder valve ON.
If bubbles appear at any connection, there is a leak.
- Turn cylinder valve OFF.
- If leak is at hose/regulator connection: tighten connection and perform another leak test. If bubbles continue appearing, the hose should be returned to the place of purchase.
- If leak is at regulator/cylinder valve connection: disconnect, reconnect, and perform another leak check. If you continue to see bubbles after several attempts, cylinder valve is defective and should be returned to cylinder’s place of purchase.
If NO bubbles appear at any connection, the connections are secure.
NOTE: Whenever gas connections are loosened or removed, you must perform a complete leak test.
Complete installation.
DANGER
- CARBON MONOXIDE HAZARD
- For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This fire pit consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life.
WARNING
Very hot while in a operation!
Never lean over the fireplace while in use. Do not touch tile of spark guard while the fire pit is in operation, wait until the fire pit has cooled down after use. Failure to comply with these instructions may result in serious bodily injury.
Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed.
Before Turning Gas Supply ON:
- Your fire pit was designed and approved for outdoor use only. Do NOT use it inside a building, garage, or any other enclosed area.
- Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or liquids.
- Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no leaks.
- Be sure the cylinder cover is clear of debris. Be sure any component removed during assembly or servicing is replaced and fastened prior to starting.
Before Lighting:
- Fire pit should be thoroughly inspected before each half year use, and by a qualified service person at least annually. If relighting a hot fire pit, always wait at least 5 minutes.
- Inspect the visible portion of the hose before each use of the appliance. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly specified by manufacturer.
- The pressure regulator and hose assembly supplied with the appliance must be used. Replacement pressure regulators and hose assemblies must be those specified by the appliance manufacturer.
Lighting:
- Turn the control knob to the “OFF” position (Figure a).
- Fully open LP cylinder valve.
Note: For initial start or after any cylinder change, hold Control Knob in for 10 seconds to purge air from gas lines before proceeding. - Push in gas control knob and turn counterclockwise to “IGNITER” (Figure b) to light the fire pit. If needed, keep pressing and turning control knob counterclockwise until the heater lights (You should hear clicking sound).
- After fire pit lights, release control knob. Push in and turn the control knob to the “HIGH” (Figure c), then release control knob. If you want a lower temperature, push in the control knob and turn clockwise to the “LOW”.
Note: Improper operation, can cause injury or properly damage. If burner fails to remain lit, all valves should be closed and a waiting period of at least 5 minutes should pass before attempting to light.

OFF: The heater stop work
LOW: Minimum temperature position
HIGH: Maximum temperature position
WARNING
FOR YOUR SAFETY
Be careful when attempting to manually ignite this fire pit. Holding in the control knob for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition.
When fire pit is ON:
Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. The flame should be blue with straight yellow tops. If excessive yellow flame is detected, turn off heater and consult “Troubleshooting” on
Re-lighting:
- Turn control know to “OFF”.
- Repeat the “Lighting” steps on prior page.
WARNING
FOR YOUR SAFETY
Fire pit will be hot after use. Handle with extreme care.
Shut Down:
- To extinguish burner depress control knob and continue to turn it clockwise to “OFF”.
- Turn cylinder valve clockwise to “OFF” and disconnect regulator when fire pit is not in use.
Operation Checklist
For a safe and pleasurable heating experience, perform this check before each use.
Before Operating:
- I am familiar with entire owner’s manual and understand all precautions noted.
- All components are properly assembled, intact and operable.
- No alterations have been made.
- All gas connections are secure and do not leak.
- Wind velocity is below 10 mph.
- Unit will operate at reduced efficiency below 40°F.
- Fire pit is outdoors (outside any enclosure).
- There is adequate fresh air ventilation.
- Fire pit is away from gasoline or other flammable liquids or vapors.
- Fire pit is away from windows, air intake openings, sprinklers and other water sources.
- Fire pit is at least 24 in. on rear and at least 24 in. on sides from combustible materials.
- Fire pit is on a hard and level surface.
- There are no signs of spider or insect nests.
- All burner passages are clear.
- All air circulation passages are clear.
- Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
- Young children should be carefully supervised when they are in the area of the fire pit.
- Clothing or other flammable material should not be hung from the fire pit, or placed on or near the fire pit.
- Any guard or other protective device removed for servicing the fire pit must be replaced prior to operating the fire pit.
- Installation and repair should be done by a qualified service person. The fire pit should be inspected before use and at least annually by a qualified service person.
- More frequent cleaning may be required as necessary. It is imperative that control compartment, burner and circulating air passageways of the fire pit be kept clean.
After Operation:
- Gas control is in “OFF” position.
- Gas tank valve is OFF.
- Disconnect Gas line.
Gas Requirements
- Use propane, butane or their mixtures gas only.
- The pressure regulator and hose assembly to be used must conform to local standard codes.
- The installation must conform to local codes, or in the absence of local codes, with the standard for the storage and handling of liquid petroleum gases
- A dented, rusted or damaged tank may be hazardous and should be checked by your tank supplier. Never use a tank with a damaged valve connection.
- The tank must be arranged to provide for vapor withdrawal from the operating cylinder.
- Never connect an unregulated tank to the heater.
CARE AND MAINTENANCE
WARNING
FOR YOUR SAFETY
- Do NOT touch or move fire pit for at least 45 minutes after use.
- Reflector is hot to the touch.
- Allow reflector to cool before touching.
To enjoy years of outstanding performance from your fire pit, make sure you perform the following maintenance activities on a regular basis:
Keep exterior surfaces clean.
- Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.
- While cleaning your unit, be sure to keep the area around the burner dry at all times. Do not submerge the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be replaced.
a) Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.
b) Do not obstruct the flow of combustion and ventilation air.
c) Keep the ventilation opening(s) of the cylinder enclosure free and clear from debris. - Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible blockage include:
Visually checking portions of the hose assembly located within the confines of the burner. Inspect the entire hose assembly at least annually, disassembling the reflector and burner. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. Then assembling the reflector and burner again following with step 6 and 7.
- Fire pit does NOT reach the desired temperature.
- Fire pit glow is excessively uneven.
- Fire pit makes popping noises.
- Spiders and insects can nest in burner or orifices. This dangerous condition can damage fire pit and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles.
- Carbon deposits may create a fire hazard. Clean dome and burner screen with warm soapy water if any carbon deposits develop.
Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal. Frequently check for corroded areas and repair them promptly.
TIP:
Use high-quality automobile wax to help maintain the appearance of your fire pit. Apply to exterior surfaces from the pole down. Do not apply to emitter screen or domes.
Storage
Between uses:
- Turn Control Knob OFF.
- Disconnect LP source.
- Store fire pit upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris).
- If desired, cover fire pit to protect exterior surfaces and to help prevent build-up in air passages.
Note: Wait until fire pit is cool before covering.
During periods of extended inactivity or when transporting:
- Turn Control Knob OFF.
- Disconnect LP source and move to a secure, well-ventilated location outdoors.
- Store fire pit upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris).
- If desired, cover fire pit to protect exterior surfaces and to help prevent build-up in air passages. Never leave LP cylinder exposed to direct sunlight or excessive heat.
Note: Wait until fire pit is cool before covering.
Service
Only a qualified service person should repair gas passages and associated components.
Caution: Always allow fire pit to cool before attempting service.
TROUBLE SHOOTING
| PROBLEM | L PROBLEM CAUSE | CORRECTIVE ACTION |
| Burner Flame is Low | Gas pressure is low | Turn cylinder valve OFF and replace cylinder |
| Outdoor temperature is less than 40°F and tank is less than 1/4 full | Use se a full cylinder | |
| If control knob fully ON | Check burner and orifices for blockage | |
| Burner Won’t Light | Control knob is not in ON position | Turn valve to ON |
| Propane cylinder is frosted over | Wait until the propane cylinder warms up and becomes unfrosted | |
| Blockage in orifice | Clear blockage and clean | |
| Thermocouple bad | Replace thermocouple | |
| Pilot light assembly bent | Place pilot properly | |
| Not in correct location | Position properly and retry | |
| Carbon Build-up Thick Black Smoke | Dirt or film on reflector and burner screen | Clean ignition screen |
| Blockage in burner | Remove blockage and clean burner inside and outside |
Documents / Resources
![]() | 3177588 Fire Pit Table |
References
- User Manualmanual.tools

Fire pit ignites but will not stay lit.
Why does my fire pit ignite but fail to stay lit?
Based on the troubleshooting guide for the Intertek 3177588 Fire Pit Table, if your fire pit ignites but will not stay lit, please check the following:
Note: If the burner fails to remain lit, close all valves and wait at least 5 minutes before attempting to light it again.
Read the full Q&A page