HEATHKIT HD-1515 Phone Patch Instruction Manual

HEATHKIT-logo

HEATHKIT HD-1515 Phone Patch

HEATHKIT-HD-1515-Phone-Patch-product

Loading PDF…
Download PDF

INTRODUCTION

The Heathkit Model HD-1515 Phone Patch enables you to transfer audio signals between a telephone line and two-way radio equipment. The heart of this solid-state Phone Patch is formed by an integrated active speech and transmission circuit, which allows you to connect the Phone Patch directly to a phone line through a built-in active low-voltage polarity-protection interface circuit. These circuits along with an 8-pole low-pass filter, obtain their power directly from the phone line in most installations. You can use an internal battery circuit in installations where the phone line exhibits a very lowvoltage condition.
Special speech transmission circuits replace the bulky and sometimes costly hybrid transformers usually used in conventional phone-patch equipment to perform the 4-wire to 2-wire radio-to-phone line conversion. The circuitry provides some automatic gain control that helps you compensate for the varying attenuation that is introduced by different line lengths or loop distance on the external phone circuit.
A high degree of electrical isolation from the radio equipment makes this Patch ideal for voice-operated installations. You can monitor the transmission between your radio and the phone line on your own home phone. A standard, mini-modular jack on the rear panel makes connection to a phone line convenient and simple.
An 8-pole filter in the input circuit makes the Patch compatible with all subscriber loop-frequency voice standards as prescribed in Part 68 of the Federal Communication Commission’s Rules and Regulations. Also, a built-in detector circuit enables you to use a VTVM or VOM to adjust for optimum sepрaration between transmit and receive. The small, compact, and low-profile design of this Phone Patch makes it a handy addition to any hamshack, for the newcomer and old timer alike.

ASSEMBLY NOTES

TOOLS
You will need these tools to assemble your kit.

HEATHKIT-HD-1515-Phone-Patch-fig- (1)

ASSEMBLY

1. Follow the instructions carefully. Read the entire step before you perform each operation.
2. Refer to the separate “Illustration Booklet” for the Pictorials and Details. Keep the “Illustration Booklet” with the Assembly Manual. The illustrations in it are arranged in the proper sequence called for in the steps.
3. Pictorials show the overall operation for a group of assembly steps; Details generally illustrate a single step. When you are directed to refer to a certain Pictorial “for the following steps,” continue using that Pictorial until you are referred to another Pictorial for another group of steps.
4. Position all parts as shown in the Pictorials.
5. Solder instructions are generally given only at the end of a series of similar steps. You may solder more often if you desirе.
6. Each circuit part in an electronic kit has its own component number (R2, C4, etc.). Use these numbers when you want to identify the same part in the various sections of the Manual.
These numbers, which are especially useful if a part has to be replaced, appear:
-In the Parts List,
-At the beginning of each step where a component is installed,
-In some illustrations,
– In Troubleshooting Charts,
– In the Schematic,
– In the sections at the rear of the Manual.
7. When you are instructed to cut something to a particular length, use the scales (rulers) provided at the bottom of the Manual pages.

SAFETY WARNING:

Avoid eye injury when you cut off excessive lead lengths. Hold the leads so they cannot fly toward your eyes.

SOLDERING
Soldering is one of the most important operations you will perform while assembling your kit. A good solder connection will form an electrical connection between two parts, such as a component lead and a circuit board foil. A bad solder connection could prevent an otherwise well-assembled kit from operating properly.
It is easy to make a good solder connection if you follow a few simple rules:
1. Use the right type of soldering iron. A 22 to 25-watt pencil soldering iron with a 1/8″ or 3/16″ chisel or pyramid tip works best.
2. Keep the soldering iron tip clean. Wipe it often on a wet sponge or cloth; then apply solder to the tip to give the entire tip a wet look. This process is called tinning, and it will protect the tip and enable you to make good connections.
When solder tends to “ball” or does not stick to the tip, the tip needs to be cleaned and retinned.
NOTE: Always use rosin core, radio-type solder (60:40 tin-lead content) for all of the soldering in this kit. This is the type we have supplied with the parts. The Warranty will be void and we will not service any kit in which acid core solder or paste has been used.

PARTS

Resistors are identified in Parts Lists and steps by their resistance value in N (ohms), k (kilohms), or MO (megohms). They are usually identified by a color code of four or five color bands, where each color represents a number. These colors (except for the last band, which indicates a resistor’s “tolerance”) will be given in the steps in their proper order. Therefore, the following color code is given for information only. NOTE: Occasionally, a “precision” or “power” resistor may have the value stamped on it.

HEATHKIT-HD-1515-Phone-Patch-fig- (2)

Capacitors will be called out by their capacitance value in µF (microfarads) or pF (picofarads) and type: ceramic, Mylar*, electrolytic, etc. Some capacitors may have their value printed in the following manner:

HEATHKIT-HD-1515-Phone-Patch-fig- (3)

EXAMPLES:
151K = 15 × 10 = 150 pF
759 = 75 ×0.1 = 7.5 pF
NOTE: The letter “R” may be used at times to signify a decimal point: as in: 2R2 = 2.2 (pF or µF).

PARTS LIST

Unpack the kit and check each part against the following list. The key numbers correspond to the numbers on the “Parts Pictorial.” Do not remove components from the tape until you use them in a step. If a part is packed in an individual envelope with the part number on it, identify the part; then return it to the envelope until a step calls for it. Do not throw away any packing material until you account for all of the parts.

To order a replacement part, always include the PART NUMBER. Use the Parts Order Form furnished with this kit. If a Parts Order Form is not available, refer to “Replacement Parts” inside the rear cover of this Manual. For prices, refer to the separate “Heath Parts Price List.”

STEP-BY-STEP ASSEMBLY

CIRCUIT BOARD ASSEMBLY STEP-BY-STEP ASSEMBLY
Refer to Pictorial 1-1 as you read the following notes and steps.

NOTES:
1. Many circuit board drawings, such as the one shown in Pictorial 1-1, are divided into two or more sections. These sections show you which area of the circuit board you are working in for a specific series of steps.
2. Refer to the “Taped Component Chart.” Note that it is divided into numbered sections that match the sections on the circuit board.
Each series of steps has you installing parts in a top-to-bottom, left-to-right sequence. Осcasionally, you may be directed to install a component in an area out of sequence. Thesecomponents are each identified in the step and on the Pictorial with a special callout.
Check off each step as you perform it. You may also wish to place a check mark near each component on the Pictorial as you install it.
In general, solder instructions are given only at the end of a series of steps. You may solder more often, if you desire.
NOTE: Refer to the “Taped Component Chart”before you begin.
In the following steps, you will be given detailed instructions on how to install and solder the first part on the circuit board. Read and perform each step carefully. Then use the same procedure whenever you install parts on a circuit board.
Note that the circuit board has foil on one side and component outlines on the other. The side with the component outlines is referred to as the “component side.”
Position the circuit board as shown in the Pictorial with the component side up. Always install components on the component side of the circuit board, and solder the leads to the foil on the other side unless a step specifically directs you otherwise.

Section 1
() R39: Hold a 2200 ປີ (red-red-red) resistor as shown and bend the leads straight down to fit the hole spacing on the circuit board.HEATHKIT-HD-1515-Phone-Patch-fig- (4)

() Start the leads into the holes at the resistor’s location in Section 1 of the circuit board. Theend with the color bands may be positioned either way. NOTE: Resistors are identified on the circuit board by the following outlines:HEATHKIT-HD-1515-Phone-Patch-fig- (5)

CIRCUIT BOARD CHECKOUT

Carefully inspect the foil side of the circuit board for the following most-commonly-made errors:
(☑ Unsolderd connections.
(5 Poor solder connections.
() Solder bridges between foil patterns.
(☑ Protruding leads which could touch together or touch the chassis when the circuit board is installed later.
Refer to the illustrations where parts are installed as you make the following visual checks:
( Electrolytic capacitors for the correct position of the positive (+) or negative (-) marked lead.
( Diodes for the proper type and installation.
(Transistors for the proper type and installation.
(☑ Integrated circuits for the proper type and installation.
Set the circuit board aside temporarily.

CHASSIS
Refer to Pictorial 2-1 for the following steps.
(✓ Position the chassis as shown in the Pictorial. Note the locations of the three holes along the front edge.
(✓Carefully peel away the backing paper from a foot. Then press the foot onto the bottom of the chassis near one of the rear corners as shown.
(5 Similarly, install feet on the bottom of the chassis near the remaining three corners. Note that the dimensions for the locations of thetwo feet along the front edge of the chassis are different than the rear feet.
(☑ Carefully peel away the backing paper from the FCC label. Then press the label onto the bottom of the chassis in the area shown.
(5 Carefully peel away the backing paper from the blue and white label. Then press the label onto the bottom of the chassis in the area shown. NOTE: Be sure to refer to the numbers on this label in any communications you may have with the Heath Company about your kit.
Carefully peel away the backing paper from the Manufacturer’s label. Then press the label onto the bottom of the chassis in the area shown.
Refer to Pictorial 2-2 for the following steps.
(✓ Position the chassis as shown in the Pictorial.
NOTE: If there is paint on the inside of the chassis around the mounting holes for the hardware that you will install in the following steps, be sure to scrape it off.
(Mount 4-40 × 1/2″ hardware onto the chassis at hole A.

INITIAL TESTS & ADJUSTMENTS

RESISTANCE CHECKS

NOTE: You will need a volt-ohmmeter to perform the following tests. If you do not have one, proceed to “Operational Checks.”
Refer to Pictorial 3-1 for the following steps.
If you obtain the proper results in the following tests, proceed to the “Operational Checks.” If you do not obtain the correct results, refer to the “In Case of Difficulty” section of this Manual and the Schematic Diagram.
NOTE: Do not connect the Phone Patch to your telephone line until you are directed to do so.
() Be sure the PATCH pushbutton is in the OFF position (knob out).
() Set controls R33 and R27 on the rear of the circuit board to the centers of their rotation.
( ) Set controls R43 (TRANS) and R5 (RCVR) on the front panel to 5.
() Set your ohmmeter to the R × 10 range.
NOTE: This Phone Patch uses two separate ground systems. Make sure you connect the negative (or common ohmmeter) lead to the correct ground, as indicated in the following steps.
() Connect the negative (or common ohmmeter) lead to the bare wire that is connected between controls R43 and R5 (chassis ground). Leave this lead connected to this wire until you are directed to disconnect it.
() Touch the positive ohmmeter lead to socket J2 lug 1. The ohmmeter should indicate between 30 and 50 ohms.
() Set your ohmmeter to the R × 1000 range.
() Touch the positive ohmmeter lead to socket J3 lug 1. The ohmmeter should indicate infinity.
NOTE: It may take several seconds for the meter to reach the correct indication. This isdue to the charging effect of some of the capacitors in the circuit.
() Disconnect the negative or common ohmmeter lead from the bare wire and connect it to the lead at the unbanded end of diode D5 (circuit board ground).
() Set your ohmmeter to the R × 100 range.
() Touch the positive ohmmeter lead to integrated circuit U2 pin 8. The ohmmeter should indicate 700 ohms or higher.
() Set your ohmmeter to the R × 10K range.
() Touch the positive ohmmeter lead to integrated circuit U1 pin 3. The ohmmeter should indicate 14 kN orhigher.
() Touch the positive ohmmeter lead to the emitter (E) lead of transistor Q1. The ohmmeter should indicate 12 k orhigher.
() Touch the positive ohmmeter lead to the emitter (E) lead of transistor Q3. The ohmmeter should indicate 12 k or higher.
() Disconnect the ohmmeter leads from the circuit board.

OPERATIONAL CHECKS

NOTE: To perform the following checks, you willhave to connect the Phone Patch to your telephone line. Use the modular duplex jack and modular cable supplied with this kit. This will allow you to connect the Phone Patch and your telephone to the samewall socket. If you do not already have modular jacks in your home, you can purchase the necessary conversion parts from many department stores or your local Phone Center.
( ) Make sure the PATCH pushbutton on your Phone Patch is OFF (knob out).
() Be sure you have read the “FCC Requirements” on Page 2 before you continue. ) Refer to Pictorial 3-2 and connect the Phone Patch to your telephone line as shown.
NOTE: Do not install a battery in your Phone Patch unless a step directs you to do so.
() Push the PATCH pushbutton on the Phone Patch to ON (knob in). The ON LED should light.
() Lift the handset of your telephone and make sure there is a normal dial tone. Then hang up the telephone and release the PATCH pushbutton to OFF.

NOTES:
1. The following steps determine whether or not you need to install a battery in your Phone Patch.
2. For the following test, you will need an isolated VOM or VTVM (one that is not grounded at the AC outlet). If your meter has a 3-wire line cord, you can install a cheater adaptor to disconnect the ground during these tests.
() Set your voltmeter to measure 15-volts DC.
() Connect the negative or common lead of your meter to the lead at the unbanded end of diode
D5. Do not let this lead touch the chassis. (C ) Connect the positive meter lead to the lead that passes through ferrite beads FB1 and FB2.
() Lift the handset of your telephone and dial an outside number (such as a friend, neighbor, or the weather). 00 Push the PATCH pushbutton to ON (knob in).
The voltmeter should indicate at least 3.5 volts DC. If the meter indicates less than 3.5 volts DC, you must install a battery in your Phone Patch to make up for the low telephone line voltage.
( ) Release the PATCH pushbutton to OFF (knob out) and hang up the telephone.
() If the above test determined that you need to install a battery, do so at this time. Some suitable 9-volt batteries (NEDA #1604) are listed below. IMPORTANT: DO NOT install a battery if you measured 5.5 volts DC or higher in the above test.
Eveready #216 or #1222
Mallory #M1604
Mallory #TR-146X (long life)
Burgess #2V6
RCA #XS323
Hellesens #410
Varta #438
If you do not install a battery, refer to the inset drawing on the Pictorial and slide the length of fiber sleeving onto the battery snap connector. Then store the connector in the battery clip.

NULL ADJUSTMENT
NOTE: Before you can perform the following steps, you must have the Phone Patch connected to your telephone line and radio equipment. Refer to the “Installation & Operation” section of this Manual for the proper connections.
Refer to Pictorial 3-3 for the following steps.
() Preset the front panel controls as follows:
PATCH pushbutton
TRANS GAIN control
RCVR GAIN control
OFF (out)
Preset the LINE NULL controls (through their holes in the rear panel to the centers of their rotation).

) Prepare a 5″ white solid wire. Then push one end of the wire into wire socket TP OUT and theother end into wire socket TP/IN.
) Connect the negative (or common) lead of your DC voltmeter to the bare wire that is connected between controls R43 and R5.
) Connect the positive voltmeter lead to wire socket METER OUT.
) Set the DC voltmeter to its lowest range.
() Tune your receiver to a strong, steady station (such as standard time and frequency station WWV) so you hear an approximate 1000 Hz tone.
() Lift the telephone handset and call some outside number (such as a friend or neighbor).
NOTE: This must be a complete call to an outside number.
() Explain to the person you have called that there will be noise and tones on the line for a few minutes while you are making adjustments. Also tell the person not to say anything until you are finished. Any sound on the line, other than those mentioned above will affect your adjustments.
() Push the PATCH pushbutton to ON (in).
() While you listen to the receiver on your telephone, adjust the RCVR GAIN control on the
Phone Patch for the volume you desire. NOTE:
Do not adjust the control for maximum volume. Excessive audio will result in clipping and distortion.

Heathkiť
() You should now have an indication on the voltmeter. If you do not have an indication, adjust the NULL 2 control (through a hole in the rear panel of the Patch) until you obtainan indication.
() Adjust the NULL 2 control for as low an indication as possible on the voltmeter.
Adjust the NULL 1 control to the 10 o’clock position (as viewed from the rear panel). Then readjust the NULL 2 control for the lowest possible indication. NOTE: You may have to alternate between the NULL 1 control and the NULL 2 control to obtain the lowest possible indication. Do not, however, turn the NULL 1 control farther counterclockwise than 9 o’clock.
NOTE: The above adjustments should prove satisfactory in most cases. You may be able to improve the adjustment by connecting an AC voltmeter or an oscilloscope to TP OUT and adjusting the NULL 1 and NULL 2 controls for the minimum indication on these instruments.
) Hang up the telephone and release the PATCH pushbutton to OFF.
() Disconnect the voltmeter and the jumper wire from the Phone Patch.
() Refer to Pictorial 3-4 and use four #6 × 1/4″ sheet metal screws to mount the cabinet shell onto the chassis as shown. Do not overtighten these screws.
This completes the adjustment of your Phone Patch. No further adjustment should be necessary unless you move the Patch to a different location.

INSTALLATION & OPERATION

Before you begin to install your Phone Patch, keep the following functions in mind:

1. Sound on the telephone line passes through the Phone Patch and feeds the microphone input on your transmitter via the MIC jack.
2. Signals from your receiver enter the Phone Patch via the REC jack, pass through the Phone Patch, and are applied to the telephone line.
Interconnection between the Phone Patch and your radio equipment varies from one piece of equipment to another. The following steps show you how to connect the Phone Patch to a typical transceiver.
You should then be able to use this informatior to make the necessary connections to your particular radio equipment.
Refer to Pictorial 4-1 for the following steps.
() Use the modular cable and modular duplex jack (supplied) to connect the TELEPHONE jack on the rear panel of the Phone Patch to your telephone line.

NOTES:
1. Be sure to use shielded cable in the following steps when you connect the Phone Patch to your radio equipment.
2. Whenever you use your Phone Patch, you must have some provision to disable your station speaker. During phone patch operation, (all station control (such as monitoring and station identification) is done through your telephone.
Connect the REC socket on the rear panel of the Phone Patch to the receiver audio circuitry of your receiver. The simplest way to accomplish this is to connect this cable to the headphone jack on your receiver, since this normally disconnects the speaker automatically.
You could also connect this cable to the speaker output on your receiver, but you would need to install a switch to disable the speaker for the reason described earlier. If your receiver does not have a headphone jack or a speaker output jack for an external speaker, you will have to make a direct connection inside your receiver.
Connect the MIC socket onon the the rear panel of the Phone Patch to the microphone input of your transmitter. Some transmitters have a separate phone patch jack for this purpose. If your transmitter does not already have this provision, you could disconnect your station microphone and connect the Phone Patch to the microphone input of your transmitter. With either of these connections, audio on the telephone line will automatically key your transmitter (assuming your transmitter has VOX capability). In some cases, you may have to install an external push-to-talk switch to key the transmitter. Finally, you could make a direct connection inside your transmitter. In any case, you must be able to disable your station microphone while you are using the phone patch.

There is no reason why your equipment should ever cause harm to the telephone network. If, however, your Phone Patch seems to be malfunctioning, disconnect it until you find the source of the problem and make repairs to your equipment or telephone lines. If harm ever does occur, the telephone company may temporarily disconnect your service. They will notify you of this action promptly and provide you with the opportunity to correct the problem. The Heath Company Service Department or a local Heathkit Electronic Center can provide you with service or other assistance if your Phone Patch should ever require it. If the telephone company ever makes changes to its communications service, they will officially notify you so the operation of your equipment will not be interrupted.

OPERATION

NOTE: You can leave the Phone Patch connected to your telephone line at all times. When the PATCH switch is in the OFF position, the Phone Patch is completely isolated from the telephone line. Perform the following steps whenever you use your

Phone Patch:
1. Be sure the PATCH switch is in the OFF position.
2. Adjust your transmitter and receiver (or transceiver) for normal voice operation.
3. Lift the handset of your telephone and call the desired party. When the party answers, explain the procedure for speaking over a phone patch. State that he or she will be “on the air” whenever he or she is speaking. Also explain how VOX or push-to-talk works. The person may have to say “over” or some other expression so you know he or she is done speaking and can perform any necessary transmit-receive switching.
4. Push the PATCH pushbutton to ON.
5. Adjust the TRANS GAIN control on the Phone
Patch for the desired modulation level, and adjust the RCVR GAIN control for the desired listening level. Do not set these controls any higher than necessary for proper operation, as this could cause cross-talk on the telephone line or interference on the air.
6. If your radio equipment has VOX and ANTIVOX controls, adjust them as necessary.
NOTE: It is good practice to prevent dial tones, dial clicks, and operator’s voices from going out over the air. Be sure to review the Federal Communication’s Commission Rules and Regulations that pertain to phone patches.
7. Use the telephone to monitor the transmission and make any required station identifications during operation of the phone patch.
8. Release the PATCH switch to OFF when the phone patch is complete.

IN CASE OF DIFFICULTY

Begin your search for any trouble that occurs after assembly by carefully following the steps listed below in the “Visual Checks.” After you complete the “Visual Checks,” refer to the “Troubleshooting Charts.”
NOTE: Refer to the “Circuit Board X-Ray View” (Page 35) for the physical location of parts on the circuit board.

Visual Checks

1. Recheck the wiring. Trace each lead with a colored pencil on the Pictorial as you check it. It is frequently helpful to have a friendcheck your work. Someone who is not familiar with the unit may notice something that you have consistently overlooked.
2. Check the values of the parts. Be sure in each step that you wired the correct part into the circuit, as shown in the Pictorial. It would be easy, for example, to install a 680 N (bluegray-brn) resistor where a 68 (blue-grayblack) resistor should be installed.
3. About 90% of the kits that are returned to the Heath Company for repair do not function properly due to poor connections and soldering. Therefore, you can eliminate many troubles by reheating all connections to make sure they are soldered as described in the “Soldering” section of the “Assembly Notes” on Page
4. Check electrolytic capacitors to be sure their positive (+) or negative (-) marked lead is at the correct location.
5. Be sure there are no solder “bridges” between circuit board foils. Check to be sure all transistors and diodes are in their proper locations. Make sure each lead is connected to the proper point. Make sure each diode band is positioned above the band printed on the circuit board.
5. Check to be sure each IC is properly installed in its socket, and the pins are not bent out or under the IC. Also be sure the ICs are installed in their correct positions. 6.
7. Check for bits of solder, wire ends, or other foreign matter which may be lodged in the wiring.
8. A review of the “Circuit Description” may also help you determine where the trouble is.
NOTE: In an extreme case where you are unable to resolve a difficulty, refer to the “Customer Service” information inside the rear cover of this Manual. Your Warranty is located inside the front cover.

CIRCUIT DESCRIPTION

Refer to the Schematic Diagram while you read the following description.
Audio coming from the receiver and going to the telephone line passes through isolation transformer
T1, a filter circuit formed by integrated circuit U1, an integrated voice circuit formed by integrated circuit U2, and a polarity protection interface formed by transistors Q1 through Q4 before it is applied to the telephone lines.
Conversely, audio coming from the telephone line and going to the transmitter passes through the polarity protection circuit formed by transistors Q1 through Q4, the integrated voice circuit formed by integrated circuit U2, and isolation transformer Т2 before it is applied to the microphone input of the transmitter.
The Phone Patch circuitry will now be described in detail.

INPUT CIRCUIT
Audio signals coming from the receiver first pass through isolation transformer T1, which isolates both electrical and ground potentials from the remaining circuitry. Resistor R1 and capacitor C2 couple the signals at the secondary of T1 to the input of a low-pass filter formed by integrated circuit U1.
Control R5 allows you to set the amplitude of the signal that is applied to the filter circuit. Integrated circuits U1A through U1D form a quad operational amplifier, which along with the associated circuitry, form a 2100 Hz low-pass active audio filter at its 6 dB point. This filter attenuates any undesirable signals coming from the receiver so that the Patch is compatible with subscriber loop frequency standards before they are applied to the telephone lines. Resistor R25 and coupling capacitor C13 couple the signal at the output of the low-pass filter to the input of integrated voice circuit U2, which is described next.

INTEGRATED VOICE CIRCUIT
Integrated circuit U2 is designed to replace the bulky transformers that are present in conventional phone patches. U2 performs the necessary 2-wire to 4-wire conversion between the transmitter/receiver and the telephone lines. It also performs automatic gain regulation up to 6 dB, depending upon the length of the transmission looр.
While the receiver signal is being applied to the telephone line, the least amount of audio possible must reach the microphone input of the transmitter. If audio was allowed to reach the microphone input, it could undesirably trigger the transmitter VOX circuit. A nulling bridge circuit formed by resistor R26, capacitor C15, and control R27 allows you to set the gain of the voice circuit during receive. Resistor R34 and control R33 allow you to balance the separation between the transmit and receive signals.
Power for integrated circuits U1 and U2 comes from the telephone line after it passes through the polarity protection circuit described next.

POLARITY PROTECTION CIRCUIT
Transistors Q1 through Q4 form an active bridge circuit that makes up the polarity protection circuit. Whenever the Phone Patch is turned on, the voltage drops between the collector-to-emitter junctions of these transistors, causing them to be saturated (or turned on). Depending upon the polarity of the input voltage coming from the telephone line, either transistors Q1 and Q4 or transistors Q2 and Q3 will conduct. If the emitters of transistors Q1 and Q2 are positive and the emitters of transistors Q3 and Q4 are negative, for example, Q2 and Q3 will conduct. Conversely, transistors Q1 and Q4 will conduct for the opposite polarity. The output polarity at the collectors of Q2 and Q4 (positive) or Q1 and Q3 (negative), therefore, is the same regardless of the line polarity.

Documents / Resources

PDF thumbnailHD-1515 Phone Patch
Instruction Manual · HD-1515, HD-1515 Phone Patch, Phone Patch, Patch

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.