EDM 08391 Drill Instruction Manual

EDM 08391 Drill

SYMBOLS

SECURITY INSTRUCTIONS

SYMBOLS: The following symbols are used in this manual and on the machine:

Read all warnings and safety instructions. Ignoring warnings and following instructions may result in electric shock, fire, and/or serious injury. Save the warnings and safety instructions for future reference.  The term “power tool” in the warnings refers to either the mainsoperated (corded) power tool or the battery-operated (cordless) powertool.

BEFORE USING

• Remove any packing materials and loose parts from the unit.
• Check the accessories before use. They must fit the machine and its purpose.
• If the machine is new, the battery must be charged first.
• Attention! After long storage, the battery capacity will decrease.
• A new battery or one that has not been used for a long time reaches full performance only after charge and discharge cycles. A substantial drop in the run time per charge indicates that the battery is worn out and should be replaced.

WORK AREA

• Keep the area clean and well-lit. Clutter or poor lighting can cause accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks, which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Always check that the power supply corresponds to the voltage indicated on the nameplate.
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
• Avoid bodily contact with grounded surfaces such as pipes, heaters, stoves, and refrigerators. There is a great risk of electric shock if your body is grounded.
• Do not expose power tools to rain or wet conditions. If water gets into a power tool, it will increase the risk of electric shock.
• Do not damage the cable. Never use the cord to carry, pull, or unplug the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Using a cord suitable for outdoor use reduces the risk of electric shock.
• If using a power tool in a wet location is unavoidable, use a power supply protected by a residual current device (RCD). The use of an RCD reduces the risk of electric shock.

PERSONAL SECURITY

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating a power tool can result in serious personal injury.
• Wear safety gear. Always wear eye protection. Wearing safety equipment such as a dust mask, non-slip safety shoes, a hard hat, or hearing protection whenever necessary will reduce the risk of personal injury.
• Avoid accidental starts. Make sure the switch is in the off position before connecting to a power source and/or battery, lifting or carrying the tool.
• Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position increases the chance of accidents.
• Remove all adjusting wrenches or wrenches before turning on the power tool. An adjustable wrench or wrench placed in a rotating part of the power tool can cause personal injury.
• Don’t try to spread your hands too far. Keep your feet firmly on the ground at all times. This will allow you to maintain control of the power tool in unexpected situations.
• Dress appropriately. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from the power tool. Loose clothing, jewelry, or long hair can become entangled in moving parts.
• If there are devices for connecting dust extraction and collection facilities, make sure they are connected and used properly. Using these devices can reduce dust-related hazards.

USE AND CARE OF ELECTRICAL TOOLS

• Don’t expect the power tool to do more than it can. Use the right power tool for what you want to do. A power tool will perform better and be safer if it is used in the context for which it was designed.
• Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making adjustments, changing accessories, or storing power tools. These preventive safety measures reduce the risk of accidentally starting the power tool.
• Store power tools out of the reach of children when not in use, and do not allow anyone unfamiliar with the power tool or these instructions to use the power tool. Power tools are potentially dangerous in the hands of untrained people.
• Take care of the maintenance of power tools. Check for misalignment or binding of moving parts, breakage of parts, and other conditions that may affect the power tool’s operation. If the power tool is damaged, take it in for repair before using it. Many accidents are caused by poor maintenance of power tools.
• Keep cutting tools sharp and clean. Cutting tools with sharp edges are less likely to jam and are easier to control.
• Use the power tool, accessories, and tool tips, etc., in accordance with these instructions, taking into account the working conditions and the work to be carried out. Using the power tool for operations other than those intended could result in a hazardous situation.

TECHNICAL SERVICE
Your power tool should be serviced by a qualified specialist using only standard replacement parts. This will ensure that it meets the required security standards.

• Use only replacement parts and accessories recommended by the manufacturer.

SPECIAL SAFETY INSTRUCTIONS

• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
• Hold the power tool by the insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Hold the power tool by the insulated gripping surfaces when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• If possible, always use clamps or a vice to hold your work.
• Always switch off before you put the tool down.
• Ensure that the lighting is adequate.
• Do not put pressure on the tool so that it slows the motor down. Allow the bit to screw without pressure. You will get better results, and you will be taking better care of your tool.
• Keep the area free of tripping hazards.
• Only use accessory bits in good condition.
• Before starting, check that there is sufficient clearance for the bit under the workpiece.
• Do not touch the bit after the operation. It will be very hot.
• Keep your hands away from under the workpiece.
• Never use your hands to remove dust, chips, or waste close to the bit.
• Rags, cloths, cord, string, and the like should never be left around the work area.
• Support the work properly.
• If you are interrupted when operating the tool, complete the process and switch off before looking up.
• Periodically check that all nuts, bolts,s and other fixings are properly tightened.
• When using the tool, use safety equipment, including safety glasses or shields, hearing protection, and protective clothing, including safety gloves. Wear a dust mask if the operation creates dust.
• Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects,s or other reproductive harm.
• Lead from lead-based paints,
• Crystalline silica from bricks, cement, and other masonry products, and
• Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals:
  Work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
• Even when the tool is used as prescribed, it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design:
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearingoccurs if effective hearing protection is not worn.

EXTRA SAFETY REGULATIONS CONCERNING BATTERY

• To ensure the longest battery life and best battery performance, always charge the battery when the temperature is between 18- 24°C. Do not charge the battery pack when the temperature is below 5°C, or above 40°C. This is important. Failure to observe this safety rule could cause serious damage to the battery pack.
• Do not incinerate the battery pack even if it is seriously damaged or can no longer hold a charge. The battery pack can explode in a fire.
• A small leakage of liquid from the battery pack may occur under extreme usage or temperature.
• This does not necessarily indicate a failure of the battery pack.

However, if the outer seal is broken and this leakage comes into contact with your skin:

• Wash the affected area quickly with soap and water.
• Flush your eyes with clean water for a minimum of 10 minutes and seek immediate medical attention.
• Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks open or cracks, immediately discontinue its use and do not recharge it.
• Do not store or carry a spare battery pack in a pocket or toolbox, or any other place where it may come into contact with metal objects.

The battery pack may be short-circuited, causing damage to the battery pack, burns, or a fire. When storing or disposing of the battery pack, cover the terminals with heavy insulation tape to ensure a short circuit cannot occur. Batteries, when stored for a long period of time, will discharge.

• Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40°C, such as alongside sheds or metal structures in the summer.
• Allow the battery pack to cool down after charging. Do not place it in a hot environmen,t such as a metal shed or open trailer left in the sun.
• Only charge the battery with the charger supplied.
• Do not put the battery pack near fire or high temperature position.
• Do not splash or immerse in water or other liquids. This may cause premature cell failure.
• When transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.
• The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold.
• If the battery pack has been stored for a long time, you should activate the battery pack first before using it.
• The battery is to be disposed of safely

INTENDED USE
This product is designed for drilling in wood, metal, plastic, or similar materials and screwing/ unscrewing screws/bolts and nuts with a left and right-handed thread, by using a variety of suitable bits (not included).

COMPONENTS

1. Quick-action drill chuck
2. Torque selection ring
3. Gear selection switch
4. LED working light
5. ON/OFF switch with speed controller
6. Handle
7. Forward / Reverse switch
8. Belt clip

SPECIFICATION

• Product description: 20V Li-ion brushless compact
• Rated voltage of battery: 20V DC
• Rated Speed 0-500 / 0-1800 rpm
• Torque Setting 20 + 1
• Max torque 50 N · m
• Chuck Capacity 13 mm
• Drill Capacity Wood 35 mm / Steel 13 mm
• Sound pressure level Lpa (Kpa= 5dB(A)) 73.95 dB(A)
• Sound power level LwA (KwA= 5dB(A)) 84.95 dB(A)
• Level of vibration an (K= 1.5m/s2) 4.814 m/s2
  • 2-speed setting supports variable driving power
  • Removable metal belt clip and strap for easy carrying
  • Built-in LED worklight illuminates the work surface for greater accuracy
  • With the power indicator on the battery pack

FEATURES

• Professional brushless motor provides better performance, higher efficiency, and longer life
• Super compact design achieves small size, low weight, and high working capacity
• One-sleeve metal keyless chuck offers increased drilling durability
• 20+1 torque settings to meet different working needs

WASTE
This symbol on the product or in the instructions means that your electrical and electronic equipment must be disposed of at the end of its useful lifein a specialized container; Do not dispose it in the usual household waste container. In the EU, there are special waste collection systems for subsequent recycling. For more information, contact the local authority or the retailer from whom you purchased the product.

WARRANTY
All our products are subject to the legal warranty in force at all times regarding consumption and cover all manufacturers’ failures regarding material and quality. This warranty applies only if the instructions for use have been followed, and it is voided if the device has been forced or used improperly, or if it has been repaired by an unauthorized person.

IMPORTED BY
www.edmproduct.com
ELEKTRO3, S.COOP.C.L
F-43389675
MADE IN CHINA