SonoFF MINI-ZBDIM Zigbee Dimmer Switch User Manual

SonoFF logo

User Manual MINI-ZBDIM

SonoFF MINI-ZBDIM Zigbee Dimmer Switch

Zigbee Dimmer Switch
User Manual V1.0

Introduction

The MINI DIM (Zigbee) is an ultra-compact Zigbee 3.0 smart dimmer controller that effortlessly upgrades traditional lighting fixtures. With a maximum load current of 2A, it seamlessly integrates with dimmable LED lamps, incandescent bulbs, halogen lamps and dimmable electronic transformers, enabling remote dimming, scheduled on/off, and smart automation via the app. Built-in overheat protection, power detection, and brightness calibration ensure both convenience and peace of mind for your smart home.

SonoFF MINI-ZBDIM Zigbee Dimmer Switch - Introduction

SonoFF MINI-ZBDIM Zigbee Dimmer Switch - Button

① Button

  • Single tap: Turn device on or off
  • Press and hold for 5 seconds: Device enters the pairing mode (Pairing time 3 minutes)
  • Click three times in succession: Switch external switch type
  • Press and hold for 10 seconds: Auto calibrate dimming
  • Press and hold for 15 seconds: Restore factory settings

② LED indicator (Blue)

  • Slow flash: Device is in pairing mode
  • Fast flash: Abnormal connection with the gateway
  • Keeps on: Normal connection with the gateway
  • Keeps off: Pairing failure/Timeout
  • Flashes three times quickly: Switch the external switch trigger type
  • Flashes five times quickly: Trigger Factory Reset
  • Breathing pattern: Device is calibrating

Specification

Product name MINI DIM (Zigbee)
Product series MINI Extreme series
Product type Zigbee Dimmer Switch
Model MINI-ZBDIM
MCU EFR32MG21
Rating 220-240V~ 50Hz  400W Max  Resistive load  ε
LED 200VA
Zigbee IEEE 802.15.4
Net weight 24.5g
Product dimension 45×39.4×16.8mm
Color White
Casing material PC
Diameter of wiring (recommend) 18AWG to 16AWG SOL/STR copper conductor only
Applicable place Indoor
Working temperature 10T40 (-10℃~40℃)
Working humidity 5-95%RH, non-condensing
Certification CE/RoHS

Installation

  1. Power off
    SonoFF MINI-ZBDIM Zigbee Dimmer Switch - Power offAVTech BATR3CWWW Battery Light - Icon WARNING
    ① Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!
    ② For single-phase use only (220 – 240V~). Connecting to multiple phases may result in damage to the device.
    ③ To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current operated Circuit-breaker with Integral Overcurrent protection(RCBO) with an electrical rating of 2A has been installed before the MINI-ZBDIM.
  2. Wiring instruction
    ICON - 13 It is prohibited to connect S1 and S2 terminals to the neutral or ground wire, in order to avoid damaging the equipment and causing danger.
    ICON - 13 Make sure all wires are connected correctly.
    ICON - 13 Supported switches are rocker switch and push button and factory default by supporting double push button.
    Method of change the switch type: short press the button 3 times until the LED signal indicator flashes 3 times quickly, now you change the switch type successfully.
    SonoFF MINI-ZBDIM Zigbee Dimmer Switch - Wiring instructionInstructions for wiring symbols
    Terminals Wires
    L Live Terminal L Live Line (220240V~)
    N Neutral Terminal N Neutral Line
    O Live Output Terminal(220-240 V~)
    S1 Switch_1
    S2 Switch_2
  3. Power on
    After powering on, the device will enter the pairing mode by default during the first use and the LED signal indicator will “flash slowly”.

SonoFF MINI-ZBDIM Zigbee Dimmer Switch - Power on

SonoFF MINI-ZBDIM Zigbee Dimmer Switch - Symbol 1 The device will exit the Pairing Mode if not paired within 3mins. When you want to enter the pairing mode again, long press the button on the device for 5 seconds until the signal light “flashes slowly” and release.

Add device

  1. Download the eWeLink App
    Please download the “eWeLink” App from Google Play Store or Apple App Store.
    SonoFF MINI-ZBDIM Zigbee Dimmer Switch - App
  2. Add SONOFF Zigbee gateway
  3. Network configuration
    SonoFF MINI-ZBDIM Zigbee Dimmer Switch - Network configuration 2SonoFF MINI-ZBDIM Zigbee Dimmer Switch - Network configuration 3

Brightness Range Calibration
To use percentage-based brightness control, it is necessary to calibrate the brightness range of the device. The calibration methods are as follows:

  • Auto Calibration
    Press and hold the device button for 10 seconds, or use “Auto Calibration” in the eWeLink app. The breathing indicator shows calibration is in progress.
  • Manual Calibration
    Adjust the brightness limits manually in the eWeLink app for fine-tuned calibration.

Compatible SONOFF Gateways

Recommended SONOFF gateway models: ZBBridge-P, ZBBridge-U, NSPanel Pro, iHost.
Other compatible SONOFF gateway models: ZBDongle-P, ZBDongle-E, Dongle-M, DonglePMG24, Dongle-LMG21.

Install the device in the mounting box

SonoFF MINI-ZBDIM Zigbee Dimmer Switch - mounting box

Factory Reset
Trigger conditions (any one condition met)

  • Delete the device on eWeLink App.
  • The device that has been successfully paired can be paired again with another eWeLink account to add it.
  • Press and hold the device button for 15 seconds.

EU Declaration of Conformity
Hereby, Shenzhen Son off Technologies Co., Ltd. declares that the radio equipment type MINI-ZBDIM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/compliance/

For CE frequency
EU Operating Frequency Range:
Zigbee : 2405 – 2480 MHz
BLE: 2402– 2480 MHz
EU Output Power:
Zigbee≤10dBm
BLE≤ 10dBm
Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

WEEE Disposal and Recycling Information

WEE-Disposal-icon.png WEEE Disposal and Recycling Information All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

Scatula Manual
PAP 21 PAP 22
Carta Carta
RACCOLTA DIFFERENZIATA

SonoFF logoManufacturer: Shenzhen Sonoff Technologies Co., Ltd.
Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, 518000, China
Website: sonoff.tech
Service email: support@itead.cc
MADE IN CHINASonoFF MINI-ZBDIM Zigbee Dimmer Switch - Symbol 2

Documents / Resources

PDF thumbnailMINI-ZBDIM Zigbee Dimmer Switch
User Manual · MINI-ZBDIM Zigbee Dimmer Switch, MINI-ZBDIM, Zigbee Dimmer Switch, Dimmer Switch, Switch

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. bonjour j’ai intégrer des modules zigbee mini dim dans mon installation home assistant, je suis avec un contacteur poussoir connecté uniquement sur le S1
    comment les paramétrer en las module en impulsion unique sur S1

    LIONEL RICOU asks bonjour j'ai intégrer des modules zigbee mini dim dans mon installation home assistant, je suis avec un contacteur poussoir connecté uniquement sur le S1
    comment les paramétrer en las module en impulsion unique sur S1
    Manuals+ clarified question
    Question

    How do I configure the SONOFF MINI-ZBDIM to use a push button (single pulse) on the S1 terminal?

    Answer

    To configure your SONOFF MINI-ZBDIM for a push button (single pulse/momentary switch), you can change the external switch type directly on the device. According to the manual:

    • Method: Short press the physical button on the MINI-ZBDIM 3 times in quick succession.
    • Confirmation: The LED signal indicator will flash 3 times quickly, indicating the switch type has been successfully changed.

    The device supports both rocker switches and push buttons. By default, it is set to support double push buttons, but this triple-click sequence toggles between the available modes. Since you are using Home Assistant, ensure your Zigbee coordinator has recognized the device correctly; however, the hardware-level switch detection is handled by this manual button sequence.

    Note: Ensure S1 and S2 are never connected to neutral or ground wires to avoid damaging the equipment.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.