X-SENSE RC01 Remote Controller User Manual

X-SENSE RC01 Remote Controller- LOGO

X-SENSE RC01 Remote Controller-RC01 Remote Controller

User Manual
RCO1 Remote Controller

Thank you for purchasing this product. To ensure proper use and trouble-free operation, please read this manual carefully and store it in a safe place for future reference.

Introduction

The RCO1 is a dedicated remote controller for the X-Sense XS01-WR wireless interlinked smoke alarms. It easily controls the paired smoke alarms, sparing users the effort of straining and reaching up to the ceiling for alarm testing and silencing.
Note: The X-Sense XSOI-WR wireless interlinked smoke alarms are not included in the package. Please purchase them individually.

Important Safety Instructions and Guidelines

  • Do not hold the test button for an extended period of time or press repeatedly.
  • Do not modify this device under any circumstances.
  • Only use the batteries specified and be sure to match the polarity marking.

Package Contents

  • 1 x Remote Controller (Battery Included)
  • 1 x Adhesive Tape
  • 1 x Key
  • 2 x Screw
  • 2 x Anchor Plug
  • 1 x Manual

Product Overview

X-SENSE RC01 Remote Controller-RC01 Remote

Operating Instructions

Battery Installation
Open the rear cover by inserting the included key into the notch at the bottom of the remote controller’s backside and pry open. Peel off the insulating film on the button cell. Ensure the correct polarity of the battery and close the cover.

Pair the Remote Controller with the X-Sense Alarm

  1. Press the test button 4 times to enter pairing mode. The LED indicator on the remote controller will flash continuously.
  2. Once pairing is successful, the LED indicator will light up and then go out in about 3 seconds, indicating that the controller has exited pairing automatically. Alternatively, you can press the test button again to exit pairing.

Test the Wireless Interconnection Between Alarms

  1. Hold the test button while within wireless range. The LED indicator on the remote controller will flash.
  2. After the alarms have received a signal (takes about 7 seconds), their LED indicators will flash and the alarms will sound continuously.
  3. Release the test button. The LED indicator on the remote controller will stop flashing, indicating that the testing has ended.

Silence the Alarms
Simply press the test button to silence the alarms when non-emergency smoke (e.g. steam) causes nuisance alarms.
During an alarm state, press the test button once and all the interlinked alarms but the initiating alarm will be silenced. Press again to silence the initiating alarm. The LED indicator on the remote controller will blink blue with each press.

Test the Remote Controller’s Power Status
In standby mode (non-alarming state), when you press the test button, the LED indicator on the remote controller will blink blue, indicating normal power supply.

Technical Specifications

Transmission Frequency 868 MHz (EU/UK);
915 MHz (US)
Remote Control Range 15 m (In Open Air)
Operating Temperature -10-50 °C
Battery Type 3 V CR2032 Lithium Battery
Battery Life 1 Year

Troubleshooting

Issue Possible Cause

Solution

The indicator on the remote controller does not light up when you press the button. The insulating film on the battery has not been peeled oft Peel off the insulating film.
The battery is not properly installed. Take out the battery and install it again. Make sure the contacts are good.
The battery power is low. Replace with a new battery.
Smoke alarms do not respond to the remote controller. Unsuccessful pairing. Pair the remote controller and smoke alarms again.
Out of range or interference from the environment/ other devices. Move to a closer location or another place and try again.

Note: The range of the remote controller is dependent on many factors. Actual operational distance will vary based on the actual operating environment or other environmental factors, and other nearby electronic devices. Avoid signal blockage or interference. Electromagnetic waves generated by appliances like Ns, induction cookers or microwave ovens may disrupt normal signal transmission and affect the operational wireless range.

Disposal

This product must not be disposed of as household waste. Dispose of the device at an authorized collection point for the recycling of electrical appliances. Dustbin Icon

X-SENSE RC01 Remote Controller-RC01 RemoteSX-Sense Innovations Co., Ltd.
Email: support@x-sense.comX-SENSE RC01 Remote Controller-RC01 Remote- qrhttp://www.x-sense.com/

Documents / Resources

PDF thumbnailRC01 Remote Controller
User Manual · RC01, Remote Controller, RC01 Remote Controller
PDF thumbnailRC01 Remote Controller
User Manual · RC01, Remote Controller, RC01 Remote Controller, Controller
PDF thumbnailRC01 Remote Controller
User Manual · DBF, 2AU4DDBF, RC01 Remote Controller, RC01, Remote Controller
PDF thumbnailRC01 Remote Controller
User Manual · RC01 Remote Controller, Remote Controller, Controller

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. i bought 2 remote control x sense pro rc01 bought product does not work at all no matter what you try user manual read movies watched no matter what you try it doesn’t work wasted money
    ik heb 2 afstandbediening gekocht xsense pro rc01 gekocht produckt werkt totaal niet wat je ook probeert gebruiks aanwijzing gelezen filmjes bekeken wat je ook probeert het werkt niet weg gegooid geld

    Gooitsen Hiemstra asks <em>i bought 2 remote control x sense pro rc01 bought product does not work at all no matter what you try user manual read movies watched no matter what you try it doesn't work wasted money
    ik heb 2 afstandbediening gekocht xsense pro rc01 gekocht produckt werkt totaal niet wat je ook probeert gebruiks aanwijzing gelezen filmjes bekeken wat je ook probeert het werkt niet weg gegooid geld
    Manuals+ clarified question
    Question

    Why is my X-SENSE RC01 remote controller not working even after following the manual?

    Answer

    If your X-SENSE RC01 remote controller is not responding, please check the following troubleshooting steps based on the manual:

    • Check the Battery Film: Ensure you have opened the rear cover and peeled off the insulating film on the button cell battery. This is a common reason for the device appearing dead.
    • Verify Battery Installation: Ensure the CR2032 battery is installed with the correct polarity and that the contacts are making a good connection.
    • Pairing Mode: To pair the remote with your alarms, you must press the test button 4 times. The LED indicator should flash continuously to indicate it is in pairing mode.
    • Compatibility: Note that the RC01 is specifically designed for X-Sense XS01-WR wireless interlinked smoke alarms. It may not work with standalone or non-wireless models.
    • Range and Interference: The remote has an open-air range of 15 meters (approx. 50 feet). Ensure there are no large metal objects or electronic devices (like microwaves or TVs) causing signal interference between the remote and the alarms.

    If the LED does not blink blue when you press the test button in standby mode, the unit may not have power. If it blinks but the alarms don't respond, try the pairing process again while standing closer to the alarms.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.