RedLINK MHK2 Wireless Remote Controller Kit

Product Specifications
- Product Name: RedLINK Wireless Remote Controller Kit
- Model: MHK2
- Components: MRCH2 Controller, MIFH2 Receiver, MRC2 Cable
- Power Source: 2 x AA Alkaline batteries
- Technology: RedLINK
Welcome
- This manual is designed to help you get acquainted with your new MHK2 RedLINK™ Wireless Remote Controller. Check out the table of contents on page 2 to browse by topic.
- Need Help? Get in Touch.
- Web: https://mhk2.meushvac.com/
- Phone: 1-800-433-4822
Controller Features
- Flexible Scheduling: The controller is fully programmable. Each day can be programmed for different heating and cooling settings in 4 unique periods (Wake, Leave, Return, Sleep).
Displays Ambient Air Temperature, Relative Indoor Humidity (%), and Reports HVAC System Status: You can display actual temperature or relative humidity (%), or see whether your cooling/heating system is running. The indoor temperature display will show the temperature from the indoor unit, the MHK2 Controller, RedLINK sensor, or an average of the MHK2 and RedLINK sensor. You confirm and configure this setting during installation setup. - Auto Change from Heat to Cool: When Auto mode is selected, the MHK2 Remote Controller can automatically determine whether your home needs heating or cooling to reach the desired temperature at the right time.
- Power Method: Designed for battery operation (2 x AA Alkaline batteries).
Controller Overview

Adjusting the Temperature
- To adjust the desired temperature up or down, touch
on the controller home screen. - How long the change will be held depends on what schedule type is selected. For more information, see “Scheduling Options” on page 10.

Schedule Overrides
- A Schedule Override occurs when the Remote Controller is running a local schedule and the set point is adjusted.
- Hold Until (Temporary Hold): Overrides the current temperature set point for a maximum of 24 hours. You might use this feature to hold a temperature for a specific time.
- Permanent Hold: Overrides the current temperature set point permanently until you manually change it or reactivate a schedule.
- Holiday Hold: With a running schedule, you can hold the current system settings for a set time period, adjustable in one-day increments.
- Program Schedule Override (Temporary)
- Touch
or tap on the controller home screen to set your desired temperature. Hold Until will appear together with the time the hold will end. - To change when the hold will end, touch Hold Until and wait until the time starts blinking. Then,
touch otap r to set when you want the hold to end. Touch Hold Until once more to confirm changes and return to the home screen.n
- Touch
- After the hold period ends, the controller will automatically return to the program schedule. If you want to cancel the hold, touch Hold Until and then touch Run Schedule.
Program Schedule Override (Permanent)
- Touch
the tap on the controller home screen to reach your desired temperature. Hold Until will appear together with the time you want the hold to end. - Touch Hold Until. Permanent Hold will appear on the screen. Touch Permanent Hold to hold this temperature until you manually change it.
To end Permanent Hold and return to the program schedule, touch Permanent Hold and then touch Run Schedule.

Adjusting the Temperature in Auto Mode
Auto mode (when the controller automatically chooses heating or cooling to reach your desired temperature) is enabled by default. If your heating or cooling professional disabled it, you will not see Auto appear as an option under Mode on the controller home screen.
To choose your preferred temperatures for both heating and cooling in Auto mode, follow the steps below.

Touch Mode on the controller home screen until Auto appears. Then touch
or choose your preferred temperature setting for the mode that’s currently active (heating or cooling).
Next, touch the text (either HEAT or COOL) next to where the set point is displayed to switch to the inactive mode.
Touch
or choose your preferred temperature in the other mode. After 3 seconds of inactivity, your setting will take effect, and the controller screen will show the set point of the active mode.
Selecting System Mode
Current system mode (Heat, Cool, Dry, Fan, Auto, Off) is displayed on the controller home screen.
The mode that’s currently running (Heat or Cool) is displayed in the upper-left corner of the controller home screen.
To cycle through the available modes, touch Mode on the controller home screen, and select the appropriate mode for your desired temperature.
- Heat: Enjoy warm air at your desired temperature.
- Cool: Enjoy cool air at your desired temperature.
- Dry: Dehumidify your room. The room may be cooled slightly. Temperature may not be settable during DRY mode, depending on your equipment.
- Fan: Circulate the air in your room.
- Auto (Auto changeover): The unit selects
The operation mode according to the difference between the room temperature and the set temperature. During Auto mode, the unit changes mode (Cool Ö Heat) when the room temperature is about 4 °F (2 °C) away from the set temperature for more than 15 minutes. - Off: Turns the heating, cooling, and fan systems of the indoor unit off.

Notes:
- To set your temperature preferences in Auto mode, see page 6.
- Auto mode is not recommended if this indoor unit is connected to an anMXZ-type outdoor unit. When several indoor units are operated simultaneously, the unit may not be able to switch operation mode between Cool and Heat. In this case, the indoor unit goes into standby mode. (Refer to the table of operation indicator lamp.)
- Auto mode may not appear on the controller screen depending on your equipment and how your controller was installed.
Setting the Fan Speed
Touch the Fan on the controller home screen to cycle through available fan speed settings until the desired fan speed is displayed. Your changes will save automatically.
Available Fan speed settings:
- Auto: MHK2 will determine the optimal fan speed to meet the set temperature.
- Fixed Speed (Adjustable): The fan will run continuously, at one of five different speeds. Each time you touch the Fan, the fan speed will increase (quiet, low, medium, high, super high).
- Note: Available Fan Speed settings may vary depending on the indoor unit type and series.

Setting the Vane Direction
Touch Vane on the controller home screen to cycle through available vane modes until the desired mode is displayed. Your changes will save automatically.
Available Vane modes:
- Auto
- Swing
- Ceiling
- High
- Middle
- Low
- Floor
- Note: Available Vane Direction settings may vary depending on the indoor unit type and series.

Main Menu Overview
Touch the Menu on the controller screen and then use the arrows
to page through the following options.
- ALERTS
View, snooze, or dismiss active alerts and reminders (available only when you see the active alert symbol on the controller home screen). - SCHEDULE
Edit the local controller program schedule.
(Available only if enabled by your local heating or cooling professional.) - Holiday Hold
Set energy-saving temperature settings for when you are away. - SCREEN LOCK
Lock the screen to limit access to controller settings. - CLOCK / DATE
Manually set the clock, clock format, daylight saving time in the CLOCK sub-menu, and date in the DATE sub-menu. - CLEAN SCREEN
Disable the touchscreen for 30 seconds so you can clean it. - Navigating the Menus
Menu: Touch to access all options and sub-menus.
Touch to page through options and sub-menus.
Touch to adjust things such as temperature, time, and date.
- RECEIVER LED
Set the receiver’s LED to on or off in normal running mode. In the default mode, the receiver’s LED will be solid green. - TEMP SCALE
Choose Fahrenheit or Celsius. - RESET
Schedule: Resets to the default Monday-Friday, Saturday-Sunday local controller schedule. - DEVICE INFO
View your controller’s device information, such as the controller’s software version, the controller’s production configuration date code, receiver’s software version, device serial number, and indoor air sensor. - Back or Cancel: Touch to discard changes or go back to the previous menu.
- Select: Touch to access a sub-menu.
- Done: Touch to confirm selection.
- Tip: You can touch Select to access a sub-menu, or you can touch the text in the message area (the word SCHEDULE, for example).
Scheduling Options
This controller may be configured to be programmable or non-programmable for Residential and Commercial modes. Both options are explained below. Controller schedule is an optional menu item. It will only show up in the controller menu if enabled by your heating or cooling professional.
Residential Program Default Settings
Each day can be programmed for different heating and cooling settings in 4 unique periods (Wake, Leave, Return, Sleep) in the controller MENU/SCHEDULE. Make sure that the controller schedule is enabled by your heating or cooling professional in the controller Installer Setup menu.
See the table below for the default schedule with adjustable settings:

- Wake, Leave, Return, Sleep periods appear on the controller home screen.
- Temperature settings for all four periods, different per day or group of days, are adjustable in the controller MENU/SCHEDULE.
Schedule Period
An active period is shown underlined on the controller home screen. Periods shown vary depending on whether the local controller schedule is enabled and turned on.
- Controller schedule is turned OFF: Schedule periods are not displayed.
- Controller schedule is turned ON: Wake, Leave, Return, Sleep periods are displayed.

Commercial Program Default Settings
- This Remote Controller is pre-set to use energy-saving program settings. We recommend these settings, since they can reduce your heating/cooling expenses.
- See table below with the default 5+2 schedule (Mon-Fri; Sat-Sun), adjustable settings:

Note: Occupied 2 and Unoccupied 2 periods may be programmed as needed, depending on the installed configuration.
Setting a Schedule
- To edit a schedule on the controller screen, follow the steps below.
- Touch the Menu on the controller home screen.
- Touch the arrows
until you see SCHEDULE, then touch Select. - Touch the arrows
to select a period in a day or set of days, then touch Select on the period you want to edit. - Touch Yes to turn the system on for the period.
- Touch the time area, then touch
or tap to adjust when the period starts. Touch Select to confirm. - When the temperature area starts blinking, touch
or adjust your preferred temperature for the mode that is currently active (either heating or cooling). Touch Select to confirm. Then touch
or adjust your preferred temperature for the inactive mode. Touch Select to confirm. - Edit the next period or use the until you see DONE, then press Select to save changes and go to the home screen.
Note: Schedule menu and System ON/OFF options are available only if enabled in the controller Installer Setup menu.

Note: Images above show settings in Residential mode. The same steps apply to adjust the schedule while in Commercial mode.
Reset Schedule
To reset the controller schedule back to the default temperature settings (see “Scheduling Options” on page 10), follow the steps below.
- Touch the Menu on the controller screen.
- Touch the
or arrows until you see RESET, then touch Select. - Touch the
arrows until you see SCHEDULE, then touch Select. - Touch Yes to confirm.
- Note: The reset schedule menu option is available only if the schedule is enabled in the controller Installer Setup menu.
- Note: If you switch from a previously saved program, either Residential or Commercial, to Commercial or Residential, respectively, you must also enable a Schedule Reset after saving the change to reflect he correct program defaults.

Screen Lock Settings
- To prevent unauthorized access to the controller or to limit changes to the system settings:
- Partial Lock: Only the temperature can be changed. (Only visible if ISU 165 is disabled.)
- Full Lock: No access is allowed without a PIN code.
Applying a Screen Lock Setting
Touch the Menu on the controller home screen.
2 Touch the or arrows until you see SCREEN LOCK, then touch Select.
3 Touch the or arrows to select your desired screen lock setting, then touch Select.
4 A PIN code will appear on the screen. Write it down _ _ _ _ and keep it in a safe place for later reference.
5 Touch Select, and confirm your screen lock setting by touching Yes.

Note: A locked screen will be indicated by a lock symbol at the bottom of the controller screen. Full Lock, Partial Lock, and ISU settings 161-167 can trigger the lock symbol, but only Full and Partial Lock can be unlocked with the PIN.
Unlocking the Screen
- Touch the lock symbol
on the controller home screen. - When prompted to enter a PIN code, touch
or select the first number of the PIN code. Touch Select to confirm, and repeat for the remaining numbers.

Note: If touching the lock symbol does not prompt for the PIN, you must disable the lockout setting(s) in ISUs 161-167 to make the needed change.
When you enter the correct PIN, you’ll return to the controller home screen. To re-lock the screen after you’re done making changes, follow the steps above to apply a lock setting.
Setting the Date and Time
Setting the Date
- Touch the Menu on the controller home screen.
- Touch the
or arrows until you see DATE, then touch Select. - Touch
or to set the month, then touch Select to confirm. - Continue to set the day and year in the same way. Touch Select to save your changes.
- Setting the Time
- Touch the Menu
on the controller home screen. Touch the or arrows until you see CLOCK, then touch Select. - Touch the
or arrows until you see SET TIME, then touch Select. - Press
or to set the time (or press and hold the buttons to move more quickly). Touch Done when finished. - Set clock format (12 hours or 24 hours) and daylight saving time in the same CLOCK sub-menu.

Cleaning the Controller Screen
With the clean screen option, you can lock the controller screen so you don’t accidentally change your settings when you clean. Follow the steps below to activate clean screen mode.
- Touch the Menu on the controller home screen.
- Touch the
arrows until you see CLEAN SCREEN, then touch Select.

The screen will deactivate for 30 seconds. A countdown timer will display the amount of time until screen reactivation.
Tip: To clean the controller screen, spray water or household cleaner onto a cloth, then use the cloth to clean the screen. Avoid abrasive cleaners and do NOT spray liquid directly on the controller.
Choosing Fahrenheit or Celsius
To select a temperature scale, follow the steps below.
- Touch the Menu on the controller home screen.
- Touch the
or arrows until you see TEMP SCALE, then touch Select. - Touch the
arrows to select FAHRENHEIT or CELSIUS, then touch Done to save your changes. - Touch Back to return to the controller home screen.

Viewing Controller Information
To see your controller’s technical information, follow the steps below.
- Touch the Menu on the controller home screen.
- Touch the
or arrows until you see DEVICE INFO, then touch Select. - Touch the
arrows to view information such as:

- Controller’s software version
- RedLINK’s software version
- Controller’s production configuration date code
- Controller model
- Device serial number
- Receiver’s software version
- Receiver model
- Indoor air sensor’s firmware version (if available)
- Indoor air sensor’s battery (if available)
Wi-Fi Connection Status
For the Wi-Fi icon in the top-right corner of the screen, there are three displayed settings:

No icon: The MIFH2 RedLINK Wireless Receiver is not connected to the Mitsubishi Electric Wireless Interface 2.
Disconnected icon: The MIFH2 RedLINK Wireless Receiver is connected and communicating with the Mitsubishi Electric Wireless Interface 2, but the Wireless Interface is not connected to a Wi-Fi network.
Connected icon: The MIFH2 RedLINK Wireless Receiver is connected and communicating with the Mitsubishi Electric Wireless Interface 2, and the Wireless Interface is connected to a Wi-Fi network.
Note: The MHK2 supports the Mitsubishi Electric Wireless Interface 2 or later, which allows the system to be connected to kumo cloud®.
RedLINK Wireless Receiver LED Status
Connect LED:
- Flashing Green: In RedLINK Wireless setup mode.
- Fast Flashing Green: In the process of pairing.
- Solid Green: At least one RedLINK™ device is enrolled onto the receiver.
- Amber: Please wait.
- Red: RedLINK™ device is not communicating.
- Off: No RedLINK™ devices are enrolled onto the receiver.
Notes:
- Flashing status light times out after 15 minutes of inactivity. Press CONNECT again if necessary.
- When first powered on, the status light will be off.
Battery Replacement
- Batteries are required to power the controller.
- Install fresh batteries immediately when the low battery alert appears. The alert appears about two months before the batteries are depleted.
- Even if the low battery alert does not appear, you should replace batteries once a year, or before leaving home for more than a month.
- All other settings are permanently stored in memory and do not require battery power.
Notes:
- When replacing batteries, alkaline batteries are recommended.
- When the battery power is low, the controller’s backlight is disabled to save battery power.
- When battery power is critically low, only the alert icon and the battery icon are displayed, and the controller cannot control your HVAC system. Batteries must be replaced immediately.

Alerts and Maintenance Reminders
- The MHK2 Remote Controller comes with a set of Smart Alerts and Reminders that help keep your heating and cooling system running correctly and efficiently. Smart alerts remind you to replace the battery or filter (if filter reminder is set up by the installer). Non-critical alerts and maintenance reminders can be snoozed for up to 7 days and/or dismissed.
- When there’s an active alert or maintenance reminder, you’ll see the alert symbol on the controller’s home screen. To see alert information, follow the steps below.
- Touch the Menu on the controller home screen, then you’ll see the ALERTS sub-menu. (The ALERTS sub-menu will only be available when there’s an active alert.)
Touch Select to view the alert. An alert code will appear by the controller’s clock, and a description of the alert will scroll on the screen. - If the alert is non-critical, you’ll have the option to Snooze or Dismiss it. If you have multiple alerts, touch the
arrows to page through the list of active alerts and follow steps 1 and 2 above. Touch Done to finish and return to the home screen.
To see what each alert code means and the action you should take, refer to the chart below.

Note: Please refer to the indoor unit manual for more details if the alert code you see is not listed in the above chart.
Change Filter Notifications
You may edit Change Filter Notifications within the Function Codes under the Advanced Menu. To modify the notifications, follow the steps below.
- To access the Advanced Menu, press and hold the Menu button for 5 seconds. Then enter the previously noted PIN code when prompted. (See page 13.)
- Touch
or go to the Function Codes option in the Advanced Menu and touch Select. - Touch
or until you reach IUFC 07 (Function Code 7) and touch Edit. - Touch
or edit the Change Filter Notifications feature (1 = 100 hours, 2 = 2500 hours, and 3 = no filter sign indicator) and press Done. - Touch Back to save the change and return to the home screen
Troubleshooting
Screen is blank
- Verify fresh AA batteries are installed in the correct orientation.
Heating or cooling system does not respond.
- Touch Mode sets the system to Heat. Make sure the temperature is set higher than the inside temperature.
- Touch Mode to set the system to Cool. Make sure the temperature is set lower than the inside temperature.
- Check the circuit breaker and reset if necessary
Temperature settings do notchange
Your installer may have set a range stop setting for heat or cooling. Contact your installer to verify the range stop settings on the controller. Default range stops settings are:
- Heat: 40 °F to 90 °F (4.5 °C to 32.5 °C)
- Cool: 50 °F to 99 °F (10.0 °C to 37.0 °C)
Controller shows a “WAIT”screen
The MHK2 Controller will display a “WAIT” screen while it receives data from the air conditioner.
- On the “WAscreenree,n if the controller shows the RedLINK™ disconnected icon
at the top-right, the controller has lost connection with the receiver. - On the “WAIT” screen, if the controller shows the RedLINK™ connected icon,
the controller is waiting for the air conditioning to connect. - To unenroll the receiver, press and hold the bottom-center of the controller screen for 5 seconds. The controller will then be unenrolled regardless of whether the receiver is on or off.
General System Information
- CAUTION: ELECTRICAL HAZARD
It can cause electrical shock or equipment damage. Disconnect power before beginning installation. - CAUTION: ELECTRONIC WASTE NOTICE
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.
Regulatory Information
FCC Compliance Statement (Part 15.19) (USA Only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Warning (Part 15.21) (USA Only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USA Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Wireless Receiver and MHK2 Remote Control
To comply with FCC and Industry Canada RF exposure limits for the general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Section 7.1.3 of RSS-GEN
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Section 7.1.2 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.n
ADA Compliance
Please consult Chapter 3, Section 309 of the United States Access Board..

The operation of this equipment is subject to the following two conditions: This equipment or device may not cause harmful interference, and
- This equipment or device must accept any interference, including interference that may cause undesired operation.
Kumo Cloud is a registered trademark of Mitsubishi Electric US, Inc.
All other product names mentioned herein are trademarks or registered trademarks of their respective owners.
- ® U.S. Registered Trademark.
- © 2019 Mitsubishi Electric US, Inc.
- Suwanee, GA 30024
- 33-00447EFS—04 M.S. Rev. 10-19
- Printed in Mexico
Frequently Asked Questions
: How do I change the battery in the controller?
Can I connect additional sensors to the controller?
Documents / Resources
![]() | MHK2 Wireless Remote Controller Kit |
References
- Mitsubishi Electric Trane Heating and Air Conditioningmhk2.meushvac.com
- User Manualmanual.tools

