UOKIER DC02 Dash Camera Instructions

UOKIER logo

UOKIER DC02 Dash Camera

UOKIER DC02 Dash Camera image

Product instructions

UOKIER DC02 Dash Camera fig1

Button Function Instructions

  1. TF Card Slot
    Insert TF Card
  2. MIC
    Audio receiving hole
  3. RESET
    Restart and recovery hole
  4. Power / OK Button
    Long press for power on/off , short press it for OK in menu mode
  5. Down Button
    Down /Video Lock Shortcut
  6. Up Button
    Up/photo shortcut
  7. M Button
    Short press for menu setting / Long press for mode switch
  8. USB Interface
    USB Power Cable Interface
  9. GPS Interface
    GPS Interface

Instructions

Turn On / Off
Short press the power button to turn on and off the device,the blue indicator light will be on and off.
The dash camera will automatically turn off when the power is low.
Auto On / Off
After drivers start the vehicles,the dash cam would turn on automatically and start recording.It would save the video and turn off automatically after the vehicle is stalled.
G-Sensors
Built-in gravity sensors would be activated by any collision and lock the video evidence.The lock icon would be displayed on the screen.Locked videos would not be overwritten.Users could adjust G-sensor sensitivity in the setting menu.
Parking Monitor
The dash cam would turn off automatically after the vehicle is stalled.Built-in G-sensors could protect your car with its parking monitor.It can record for 18-20seconds of video once detecting external force while the vehicle has been parked.The video would be saved in the SOS folder.
Mode Switch
The default mode is Video mode.
A red spot would flash in the upper left corner when it is recording.
Users could press UP button to take a photo during recording.
Short press Power/OK button to stop recording and long press M button to Switch to Photo mode
In Photo mode,short press Power/OK button to take a photo.
Long press M Button to switch to Video/Photo playback mode. The playback icon would be displayed in the upper left corner of the screen. Short press Power/OK button to Play.

Stop recording by short pressing Power/OK button and short press M button to enter the setting interface.
Different mode has its own setting interface.

In Video setting mode,users could set Video Resolution, WDR,Video Exposure, Audio Recording, G-Sensor, Parking Monitor, Date Stamp, WIFI, Auto LCD(Screensaver), Language, GPS, Time Zone, DST, Beep Sound, Volume,
Frequency, Format SD card, Default
Setting, and Version.
In Photo Mode, users could set Capture Mode,Image
Size, Exposure,Date Stamp.
In Video/Photo Playback mode,Users could choose
Delete, Protect and Slide Shown.

Battery Charging Instructions

There are three ways to charge the battery. The red charging indicator
will light up during charging .It will take about 180 minutes to be fully charged. The red indicator will go off automatically then.

  1. Using the power cable to charge
  2. Charging with PC
  3. Charging with vehicles

Instructions for App Installation and WiFi Connection:

  1. Please install ROAD CAM in your iPhone or Android smartphone.
  2. Go to the Wlan of your phone and connect Ruien_DVR(password12345678)
  3. Then open Roadcam and connect the dashcam with your phone.
  4. You could set and watch videos simultaneously on your phone and dash camera.

Product Specification

UOKIER DC02 Dash Camera fig2

Troubleshooting

Under normal operation, if there is a problem with the product, please refer to the following solutions:

  1. It can’t take pictures Check if the TF card has enough storage or is locked.
  2. When recording, it stops automatically The TF card is incompatible or full. Please use the Class 10 TF card and check the storage of the TF card.
  3. When watching photos or videos, it shows an error Please format the TF card and device.
  4. The image was unclear Please check the lens and wipe it if it’s dirty.
  5. There are transverse fringes in the image Please set the frequency to “50 Hz” or “60 Hz” according to the local power supply frequency.
  6. It crashed Please restart it by using a needle into the reset hole.

Tips:

  1. Check the setting(Parking Monitor, G-sensor) before installing it. Advice to set the Parking Monitor to high and set the gravity sensor to medium.
  2. Check whether there is a red spot flashing during the recording process.
  3. Empty the SOS folder which can’t be overwritten by loop recording regularly on your phone or laptop in case the SD card is full.
  4. Please use class 10 TF card.
  5. Emergency videos will show Key icon on the device and stored in the SOS folder.

Technical support

www.uokier.com
Email: service@uokier.com

Manufacturer :
Shenzhen Heqi Intelligent Technology Co.,Ltd Room2601,J8,XingheWORLDFBuilding,No.1, YabaoRoad,NankengCommunity,BantianStreet, Longgang District,Shenzhen

FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Documents / Resources

PDF thumbnailDC02 Dash Camera
Instructions · DC02, 2A3FK-DC02, 2A3FKDC02, DC02 Dash Camera, Dash Camera, Camera

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. Instructions are non-existant in these manuals. They tell you to connect the camera to the road cam app, but not how. they don’t do it automatically. Nothing in the menu of the camera is self explanatory. You say there is three ways to charge the camera, no, there is one. in the car, because that is the ONLY cord that came with it. If there is not wifi available, nothing can connect. Nothing comes up after connecting to roadcam app, if it is even connecting, because there is no way to tell. The dates are off by one day, and no way to change the time. INSTRUCTIONS PEOPLE, INSTRUCTIONS. HOW DO YOU DO THIS SHIT?????

    VERY PISSED OFF CUSTOMER asks Instructions are non-existant in these manuals. They tell you to connect the camera to the road cam app, but not how. they don't do it automatically. Nothing in the menu of the camera is self explanatory. You say there is three ways to charge the camera, no, there is one. in the car, because that is the ONLY cord that came with it. If there is not wifi available, nothing can connect. Nothing comes up after connecting to roadcam app, if it is even connecting, because there is no way to tell. The dates are off by one day, and no way to change the time. INSTRUCTIONS PEOPLE, INSTRUCTIONS. HOW DO YOU DO THIS SHIT?????
    Manuals+ clarified question
    Question

    How do I connect the UOKIER DC02 to the Roadcam app, charge the device, and set the date and time?

    Answer

    To address your concerns regarding the UOKIER DC02 dash camera, please follow these specific steps from the manual:

    • App Connectivity: The camera creates its own Wi-Fi network; it does not use your home Wi-Fi.
      1. Install the ROADCAM app on your smartphone.
      2. Go to your phone's Wi-Fi settings and connect to the network named Ruien_DVR.
      3. Enter the password: 12345678.
      4. Once connected to the camera's Wi-Fi, open the Roadcam app to sync.
    • Setting Date and Time: To manually adjust settings, you must first stop the recording.
      1. Short press the Power/OK button to stop recording (the red spot should stop flashing).
      2. Short press the M button to enter the Menu Settings.
      3. Use the Up/Down buttons to navigate to Date Stamp or Time Zone settings.
      4. If you have the optional GPS module, setting the correct Time Zone will automatically sync the time.
    • Charging: While the manual mentions three ways (Power cable, PC, and Vehicle), the device is primarily designed to be powered via the USB Interface using the provided vehicle cable. If you wish to charge it indoors, you can use a standard Mini-USB cable connected to a PC or a 5V/1.5A wall adapter.

    If you continue to have issues, you can contact technical support at service@uokier.com.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.