LG VW6024R Vissani Window Air Conditioner
READ ALL INSTRUCTIONS BEFORE USE
Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and follow all safety messages. Notice the personal safety alert symbol used in this manual to draw your attention to a WARNING given
along with the particular operating instruction. This means that the operation requires special ATTENTION, CAUTION, and AWARENESS.
- Do not modify or extend the power cord.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- Use a dedicated circuit.
- Do not disassemble or modify the product.
- Adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses.
- Disconnect the power cord or circuit breaker before installing or servicing the appliance.
- Keep packaging materials out of the reach ofchildren. These materials can pose a suffocation risk to children.
- Store and install the product where it will notbe exposed to temperatures below freezing or exposed to outdoor weather conditions.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- Do not install the unit in potentially explosive atmospheres.
- Piping material, pipe routing, and installation shall include protection from physical damage in operation and service, and be in compliance with national and local codes and standards, such as ASHRAE 15, IAPMO Uniform Mechanical Code, ICC International Mechanical Code, or CSA B52. All field joints shall be accessible for inspection prior to being covered or enclosed.
- In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
OPERATION
- Use this appliance only for its intended purpose.
- Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
- Repair or immediately replace all power cords that have become frayed or otherwise damaged.
- Do not use a cord that shows cracks or abrasion damage along its length or at either end.
- Do not run cord under carpets or mats where it could be stepped on and damaged.
- Keep the cord out from under heavy objects like tables or chairs.
- Do not place the power cord near a heat source.
- Do not use an adaptor or plug the product into a shared outlet.
- Do not tamper with controls.
- If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, unplug it immediately, and contact The Home Depot Customer Information Center.
- Never unplug the appliance by pulling on thepower cord. Always grip the plug firmly and pull straight out from the outlet.
- Do not grasp the power cord or touch the appliance controls with wet hands.
- If water enters the product, turn off the power at the main circuit, then unplug the product and call for service.
If the product has been submerged, contact The
Home Depot Customer Information Center for
instructions before resuming use.
□ Unplug the product when unused for long periods.
□ Unplug the product before cleaning.
□ In the event of a gas leak (propane gas, etc.) do
not operate this or any other appliance. Open a
window or door to ventilate the area immediately.
□ This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning the use of
the appliance by a person responsible for their
safety.
□ The interior of the product must only be cleaned
by an authorized service center or a dealer.
□ Do not use solvent-based detergent on the
product. Doing so can cause corrosion or damage,
product failure, electrical shock, or fire.
□ Children should be supervised to ensure that they
do not play with the air conditioner.
□ Do not start/stop operation by plugging/
unplugging the power cord.GROUNDING INSTRUCTIONS
□ The power cord of this appliance is equipped with
a three-prong (grounding) plug. Use this with a
standard three-slot (grounding) wall power outlet
to minimize the hazard of electric shock. The
customer should have the wall receptacle and
circuit checked by a qualified electrician to make
sure the receptacle is properly grounded. DO NOT
CUT OR REMOVE THE THIRD (GROUND) PRONG
FROM THE POWER PLUG.
□ Situations when the appliance will be
disconnected occasionally; Because of potential
safety hazards, we strongly discourage the use
of an adapter plug. However, if you wish to use
an adapter, a TEMPORARY CONNECTION may
be made. Use UL-listed adapter, available from
most local hardware stores. The large slot in the
adapter must be aligned with the large slot in the
receptacle to assure a proper polarity connection.
□ Attaching the adapter ground terminal to the
wall receptacle cover screw does not ground the
appliance unless the cover screw is metal, and
not insulated, and the wall receptacle is grounded
through the house wiring. The customer should
have the circuit checked by a qualified electrician
to make sure the receptacle is properly grounded.
□ Disconnect the power cord from the adapter, using
one hand on each. Otherwise, the adapter ground
terminal might break. Do not use the appliance
with a broken adapter plug.
□ Situations when the appliance will be
disconnected often; Do not use an adapter plug
in these situations. Unplugging the power cord
frequently can lead to an eventual breakage of the
ground terminal. The wall power outlet should be
replaced by a three-slot (grounding) outlet instead.
CAUTION:\
To reduce the risk of minor or moderate injury to
persons, malfunction, or damage to the product
or property when using this product, follow basic
precautions, including the following:
INSTALLATION
□ Take care when installing the product that exhaust
or condensation does not damage nearby property.
□ Follow installation instructions exactly to avoid
excessive vibration or water leakage.
□ Wear gloves and use caution when unpacking and
installing the appliance. Screws or sharp edges
can cause injuries.
□ When installing or moving the appliance, be careful
not to pinch, crush, or damage the power cord.
□ The supply and return air openings in the
conditioned space may have the body of the
appliance may be installed in open areas such as
false ceilings not being used as return air plenums,
as long as the conditioned air does not directly
communicate with the air of the false ceiling.
OPERATION
□ This appliance is not intended for use as a
precision refrigeration system. Do not use it for
special purposes such as maintaining pets, food,
precision machinery, or art objects.
□ Make sure the air inlet and outlet are free from
obstructions.
□ Do not step on or place heavy objects on top of the
appliance.
□ Do not operate the appliance without the filter
securely installed.
□ Do not drink water drained from the appliance.
□ Be sure to ventilate sufficiently when the air
conditioner and a heating appliance such as a
heater are used simultaneously.
□ Do not expose people, animals, or plants to the
cold or hot wind from the air conditioner for
extended periods of time.
□ Remove the batteries if the remote control is not
to be used for an extended period of time.
□ Never mix different types of batteries, or old and
new batteries for the remote control.
□ Stop using the remote control if there is a fluid
leak in the battery. If your clothes or skin are
exposed to the leaking battery fluid, wash off with
clean water.
□ If the leaking battery fluid has been swallowed,
rinse the inside of the mouth thoroughly and
consult a doctor.
□ Do not recharge or disassemble the batteries.
MAINTENANCE
□ Clean the filter every two weeks.
□ Never touch the metal parts of the air conditioner
when removing the air filter.
□ Never use strong cleaning agents or solvents
when cleaning the air conditioner or spray water.
Use a smooth cloth.
□ Use a soft cloth to clean the appliance. Do not use
waxes, thinners, or harsh detergents.REFRIGERANT (FOR R32 ONLY)
WARNING: Do not use means to accelerate the
defrosting process or to clean, other than those
recommended by the manufacturer.
□ The appliance shall be stored in a room without
continuously operating open flames (for example an
operating gas appliance) and ignition sources (for
example an operating electric heater).
□ Do not pierce or burn.
□ Be aware that flammable refrigerants may not contain
an odor.
□ The installation of pipe-work shall be kept to a
minimum.
□ National gas regulations shall be observed.
□ Mechanical connections shall be accessible for
maintenance purpose.
□ The appliance shall be stored in a well-ventilated area
where the room size corresponds to the room area as
specified for operation.
CAUTION: This unit contains flammable refrigerant and
has special safety precautions not normally associated
with older units. Please follow all precautions and
advisories.
□ Use caution while handling and prevent damage to
unit. Do not put any holes into product for any reason.
This can cause damage to product and prevent unit
from cooling.
□ Maintenance and cleaning of unit should be performed
by trained personnel. Failure to properly clean unit can
result in damage to the refrigeration system and or the
electrical system.
□ Keep any required ventilation openings clear of
obstruction.
□ Service should only be performed by technicians
properly trained and certified in the use of flammable
refrigerants. Any service performed by unauthorized
servicers/individuals will void all warranties.
□ When storing the appliance, do not put in a room with
any open flame appliance, such as gas water heaters
or furnaces. Also keep away from electric heaters.
Damaged units should be repaired before storage.
□ Any person who is involved with working on or
breaking into a refrigerant circuit should hold
a current valid certificate from an industryaccredited
assessment authority, which authorizes
their competence to handle refrigerants safely in
accordance with an industry recognized assessment
specification.
□ Servicing shall only be performed as recommended by
the equipment manufacturer. Maintenance and repair
requiring the assistance of other skilled personnel shall
be carried out under the supervision of the person
competent in the use of flammable refrigerants.
□ The appliance shall be stored so as to prevent
mechanical damage from occurring.
□ The refrigerant and insulation blowing gas used in the
appliance require special disposal procedures. Consult
a service agent or a similarly qualified person before
disposing of them.Pre-Installation
NOTE: This manual may contain images or content that
may be different from the model you purchased. This
manual is subject to revision by the manufacturer.
ELECTRICAL DATA
Power cord may include a current interrupter device. TEST and RESET buttons are provided on the plug case. The
device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST
button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact
a qualified service technician.WARNING:
□ This appliance should be installed in accordance with
the National Electrical Code.
□ Use of extension cords could cause serious injury or
death.
□ Do not use an extension cord with this window air
conditioner.
□ Do not use surge protectors or multi-outlet adapters
with this window air conditioner.
□ Never push the TEST button during operation.
□ Doing so can damage the plug.
□ Do not remove, modify, or immerse this plug. If this
device trips, the cause should be corrected before
further use.
CAUTION: The conductors inside this cord are
surrounded by shields, which monitor leakage current.
These shields are not grounded. Periodically examine
the cord for any damage. Do not use this product in the
event the shields become exposed. Avoid shock hazard.
This unit cannot be user-serviced. Do not open the tamper
resistant sealed portion. All warranties and performance
will be voided. This unit is not intended to be used as an
ON/OFF switch.How to install the unit
□ To prevent vibration and noise, make sure the
unit is installed securely and firmly.
□ Install the unit out of direct sunlight.
□ There should be no obstacles, such as a
fence or wall, within 20″ from the back of the
cabinet because it will prevent heat radiation
of the condenser. Restriction of outside air will
greatly reduce the cooling efficiency of the air
conditioner.
□ Install the unit slightly tilted so the back is
slightly lower than the front (about 1/4″). This
will force condensed water to flow to the
outside.
□ Install the unit with the bottom between
30″~ 60″ above the floor level.
CAUTION: DO NOT cover or block any of the side and
top louvers. All side louvers of the cabinet must remain
exposed to the outside of the structure and unobstructed.
Cooled air
Awning
Fence
Heat
radiation
About 1/4″
Over 20″
30″~60″
2 Window requirements
□ This unit is designed for installation in
standard double hung windows with actual
opening widths from 21″ to 35″.
□ The top and bottom window sashes must open
sufficiently to allow a clear vertical opening of
12″ from the bottom of the upper sash to the
inside sill.
21″ to 35″
12″ min
3 Storm window requirements
□ Windows that include a storm window frame
may prevent the air conditioner from tilting
down toward the outside to drain properly.
For proper drainage, attach a 1″ x 2″ piece
of wood to the inner sill, trimmed to a length
which fits inside the window frame. The top
of the wood shim must be at least 3/4″ higher
than the top of the storm window frame.
Attach the wood securely to the sill with nails
or screws.
□ If necessary, attach another 1″ x 2″ wood strip
flush against the back of the inner sill. This will
raise the L bracket, as shown in the drawing.Temperature Control
The thermostat monitors room temperature to
maintain the desired temperature. The thermostat
can be set between 16 °C – 30 °C (60 °F – 86 °F).
Press or arrows to increase or decrease
temperature setting.
NOTE:
□ Auto Restart : If the air conditioner turns off due to
a power outage, it will restart automatically once the
power is restored, with the same settings as were set
before the unit turned off.
□ The remote control will not function properly if the AC
infrared sensor is exposed to direct light or if there
are obstacles between the remote controller and the
air conditioner.
USING THE LIGHT OFF FUNCTION
You can set the brightness of the control panel,
□ Press button on the control panel for 3 seconds, or
□ Press button on the remote control for 3 seconds.
NOTE:
□ If the brightness of an indoor appliance’s display is
set to OFF, pressing a button on the remote control
automatically turns the display on for 5 seconds.
□ This function may operate differently, depending on
the model.
USING THE MUTE FUNCTION
You can turn on/off the unit’s buzzer sound,
□ Press button on the control panel for 3 seconds, or
□ Press button on the remote control for 3 seconds.
USING THE AUTO CLEAN FUNCTION
In the Cooling and Dry Mode, Moisture is generated
inside the indoor unit. This function removes such
moisture.
□ Press Timer button on the remote control for 3
seconds.
□ is displayed on the display screen.
NOTE:
□ When using the product for the first time, the Auto
Clean function is not set.
□ If you turn off the unit, the fan continues to run for
10-20 minutes and cleans inside of the indoor unit.
USING THE CHILD LOCK FUNCTION
You can set the lock function to prevent children from
operating the product’s control panel. Use the Child Lock
function to prevent unintended operation or damage.
□ Press Fan speed button 3 seconds to turn the
Child Lock function on or off.
□ is displayed on the display screen.
NOTE: The remote control operates normally even
when the lock function is enabled.
USING THE CLEAN FILTER FUNCTION
The LED light up to notify you that the filter needs
to be cleaned. After cleaning the filter, press the Mode
button on the control panel or remote control 3 seconds
to turn off the light.
NOTE: This feature is a reminder to clean the air filter
for more efficient operation. The LED light turns on after
250 hours of operation.
WIRELESS REMOTE CONTROL
INSERTING BATTERIES
1. Push out the cover on the back of the remote
control with your thumb.
2. With the plus and minus poles facing as marked,
and insert two new AAA 1.5 V batteries.
Documents / Resources
 | VW6024R Vissani Window Air Conditioner |
References
- User Manualmanual.tools