NEBULA BT638 BLE Module Owner’s Manual

NEBULA -logo

NEBULA BT638 BLE Module

NEBULA-BT638-BLE-Module-product

Version Record

Version Date Author Content
V1.0 Initial Release

Introduction

Overview
The BT638 Bluetooth module is designed based on the TLSR8232 chip. It’s a Bluetooth BLE4.2 module that supports UART transparent transmission and AT commands. When in Bluetooth connection mode, it enters  data transparent transmission mode. When not connected, it can be configured via AT commands to adjust parameters such as broadcast interval and device name.

Key Features

  • Bluetooth V4.2 standard specification
  • Class II RF power, with microampere-level ultra-low power consumption
  • Ultra-low voltage operation, compatible with 3V button batteries
  • Multiple interfaces: PIO/UART/AIO/I²C/SPI/PWM
  • RoHS lead-free manufacturing process
  • Dimensions: 16.5mm (L) × 13.3mm (W)
  • Two variants: BT638-1 (without shielding cover) and BT638-2 (with shielding cover)

 Application Fields
The BT638 module is designed for IoT and HID (Human Interface Devices) applications, including but not limited to:

  • Smart home devices (access control, LED lighting control)
  • Fitness equipment (treadmills, exercise machines)
  • Medical devices (pulse meters, blood pressure monitors)
  • Home entertainment devices (remote controls, toys)
  • Office equipment (printers, scanners)
  • Commercial devices (cash registers, QR code scanners)
  • Mobile device accessories (for phones, tablets, and computers)
  • Automotive equipment (car repair tools)
  • RF and infrared remote controllers

Hardware Highlights

  • Supports up to 16 GPIOs in addition to UART communication pins
  • Equipped with hardware flow control UART interface and Swire debug interface
  • Up to 6 PWM channels
  • 6-channel 14-bit ADC
  • TX output power: up to +8 dBm
  • Hardware Connection Diagram

Hardware connection diagram

NEBULA-BT638-BLE-Module (2)The functional pins of the module can be reconfigured according to specific applications.
For example, PB3 can be set as a Bluetooth control pin (BTC) to switch other devices on/off, and PA1 can be  configured as a low-power control wake-up pin (P_SLEEP) to wake up the Bluetooth module or perform other functions.

Electrical Parameters

Absolute Maximum Ratings 

Item Sym. Min. Max Unit Conditions
Supply Voltage VDD -0.3 3.9 V All AVDD and DVDD

pin must have the same voltage

Voltage on input pin VIN -0.3 VDD+0.3 V –
Output voltage VOUT 0 VDD V –
Storage temperature range TStr -65 150 ℃ –
Soldering temperature TSld – 260 ℃ –

Recommended Operating Conditions

Item Sym. Min Typ. Max Unit Conditions
Power-supply voltage VDD 1.9 3.3 3.6 V –
Supply rise time

(from 1.6 V to 1.8 V)

Tr – – 1 ms –
Operating temperature range TOpr -40 – 85 ℃ –

Current Consumption (VDD = 3.3 V, T= 25℃)

Mode Sym. Min Typ. Max Unit Conditions
 

TX

 

ITx

– 14.5 – mA 0dBm Continuous Tx transmission
– 25 – mA 8dBm Continuous Tx transmission
RX IRx – 16. –

–

mA Continuous Rx reception
Suspend  

Isusp

– 8 – μA IO wake up
– 10 – μA Timer wake up
Flash not included,
IDeep1 – 1 – μA without 32kHz external

XOSC, and internal 32kHz

RC OSC off
Flash not included, with
Deep sleep IDeep2 – 1.7 — μA 32kHz external XOSC,

and internal 32kHz RC

OSC off
Flash not included,
IDeep3 – 2.2 – μA without 32kHz external

XOSC, and internal 32kHz

RC OSC on

NOTE:
Without 32K RC: The wakeup source is external signal from GPIO input, the internal 32K RC is disabled
With 32K RC: The wakeup source is 32K RC, it is enabled.

Module Pins and Descriptions

NEBULA-BT638-BLE-Module (3)

NO. Name Description
1 GND Groud
2 VCC 3.3V Power supply
3 NC NC
4 PC2 SPI Slave chip select (active low) / SPI Master chip select(active low) / PWM0 inverting

output/ UART_CTS / GPIO PC[2]

5 PC7/SWS Single wire slave / PWM3 output / GPIO PC[7] in Program mode as SWS
6 PA1 PWM3 inverting output/UART_CTS / GPIO PA[1]

(Set to Sleep-Wake UP Function H for Sleep L for Active)

7 NC NC
8 PC3 SPI Slave data output / SPI Master data output / PWM5 inverting output / UART_RTS/

GPIO PC[3]

9 PC4 SPI Slave data input / I2C Master serial data / SPI Master data input / UART_TX / GPIO

PC[4]

10 PC5 SPI Slave clock / I2C Master clock / SPI Master clock / UART_RX / GPIO PC[5]
11 PC1 PWM2 inverting output / GPIO PC[1]
12 PA5 PWM5 output / I2C Slave clock / I2C Master clock / GPIO PA[5]
13-19 NC NC
20 PA4 PWM2 output / UART_RX / I2C Master serial data / SPI Slave clock / GPIO PA[4] ( Set to UART RX)
21 PA3 PWM4 output / UART_TX / I2C Master clock / SPI Slave data input / GPIO PA[3] (Set

to UART TX)

22 PA6 PWM4 inverting output / I2C Slave serial data / I2C Master serial data / Control

external LNA / GPIO PA[6]

23 PB1 PWM1 output / SPI Master data output / Control external PA / GPIO PB[1] /PGA input
24 PB2 PWM2 output / SPI Master data input / UART_CTS / I2C Master clock / GPIO PB[2] /

PGA input

25 PB3 PWM0 output / SPI Master clock / UART_RTS / I2C Master serial data / GPIO PB[3]

(SET to Blue Tooth Control Pin)

26 PB4 PWM1 inverting output / UART_TX / GPIO PB[4] / PGA input
27 PB5 PWM4 output / UART_RX / GPIO PB[5] / PGA input
28 NC NC

Module Mechanical Dimensions

NEBULA-BT638-BLE-Module (4)

Module Circuit Diagram

NEBULA-BT638-BLE-Module (5)BOM

PCB assembly parts
Part Name Description QTY. Unit Remark
Capacitor ROHS 1.8pF 0201, X7R, +/-10% 2 C1, C2
Capacitor ROHS 1μF 0201, X7R, +/-10% 4 C3, C6, C7, C8
Inductor ROHS 2.2nH 0402, +/-5% 1 L1
IC Telink 2.4G Bluetooth IC TLSR8232F512ET24 QFN24 1 U1
Crystal 24 MHz 12 pF 20 ppm 2016 Package 1 Y1
PCB ROHS double-sided FR4, thickness 0.8mm,

dimensions 16.5mm×13.3mm

1 Main PCB
Shielding case Nickel silver, thickness 0.2mm, laser-etched QR code 1 Same as BT628-2

Module Installation Requirements

  • The BT638 module operates at 2.4GHz, so its placement on the product is critical to antenna performance. Avoid the following:
  • Metal enclosures can shield RF signals and prevent the module from working properly.
  • Keep internal metal components away from the module’s RF section.
  • Place the module around the edges of the mainboard, with the antenna part near the edge or corner. Avoid copper pours or traces under the antenna.
  • It’s recommended to extend the antenna area outward from the main PCB to position the module as close to the edge as possible.
  • NEBULA-BT638-BLE-Module (6)A、B:Strongly recommended。C, D, E:Acceptable but not recommended。
  • F:If the main PCB lacks space, maintain a 15mm gap between the module and the main PCB

Module Reflow Soldering Recommendations

Module Welding Guidance (Refer to IPC/JEDEC Industry Standard)

Preheating process
Rump up rate:

From TS (25℃ Room temperature)to TL (Preheating temperature)

2℃/s (Max)
 

Preheating temperature TL

150℃ (Min.)

175℃ (Typ.)

200℃ ( Max.)

Preheat time 60~120 s
Soldering
Heating rate for soldering:from (Preheating temperature) TL to TP

(Peak temperature)

1~2℃/s
Tolerance of TP 245℃ +0/-5℃
Duration of TP 10 s
Duration of soldering (Above 217℃) 40~60 s
Ramp down rate 2.5℃/s (Max.)

The reflow curve recommended

NEBULA-BT638-BLE-Module (1)

FCC Statement

FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247

PCB antenna with antenna gain -6.13dBi
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2.  This device must accept any interference received,  including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment  generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  If the FCC identification number is not visible when the module is installed inside another device, then the   outside of the device into which the module is installed must also display a label referring to the enclosed  module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2BAMT-BT638-2 Or Contains FCC ID: 2BAMT-BT638-2”
The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the  user documentation that comes with the product.
Any company of the host device which install this modular with modular approval should perform the test of  radiated & conducted emission and spurious emission,etc. according to FCC part15B Class B requirement, Only if   the test result comply with FCC part 15B Class B requirement,then the host can be sold legally. When the  module is installed inside another device, the user manual of the host must contain above Paragraphs A, B, and C warning statements.

Documents / Resources

PDF thumbnailBT638 BLE Module
Owner's Manual · BT638-2, 2BAMT-BT638-2, 2BAMTBT6382, BT638 BLE Module, BT638, BLE Module, Module

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.