ZEBRA ZPL2 Printers

Specifications
- Product: ZPL2 Printers
- Commands: ^FH, ^CI
- Code Page: 850
Product Information
The ZPL2 printers support printing special characters in the upper 128 range of Code Page 850 using ^FH and ^CI commands. These commands allow users to send hexadecimal values for characters and substitute characters from different character sets.Product
Using ^FH Command
The ^FH (Field Hex) command allows you to send the hexadecimal value for any character in the Code Page 850 set.
Example
- ^XA ^FO20,20^A0N,50,50^FH_^FD_83^FS ^XZ
Using ^CI Command
The ^CI (Change International Font) command allows you to substitute characters from different character sets and remap characters from one code page.
For X.8 or higher firmware
- ^XA ^FO20,70^CI8^A0N,50,50^FD[^FS ^XZ
For X.10 or higher firmware
- ^XA ^CI0,131,97 ^FO20,120^A0N,50,50^FDa^FS ^XZ
FAQs
Q: Can I print special characters without installing a font pack?
A: Yes, you can use the ^FH and ^CI commands to print special characters in ZPL2 without the need to install a font pack.
5/22/25, 11:45 AM
support.zebra.com/cpws/docs/zpl/zpl_spcl_chr.htm
Title: Printing special characters in ZPL2

Discussions: Methods of printing special characters in ZPL2 without installing a font pack.
Goals: Provide examples with explanations on printing special characters.
Facts or Affected Items: ZPL2 Printers, ^FH and ^CI commands, Code Page 850, ZPL2 Programmers Manual
Changes: N/A
Details
There are several ways to print characters in the upper 128 range of Code Page 850. Below are a few examples.
These examples should print the lower case “a” with a circumflex: ()
^FH (Field Hex) allows you to send the hexadecimal value for any character in the Code Page 850 set.

Format: ^FHa
Parameters:
a = hexadecimal indicator Accepted Values: any characters except current format and control prefix (^ and ~ by default). Default Value: _ (underscore) Typical values are _ or
Example:
^XA ^FO20,20^A0N,50,50^FH_^FD_83^FS ^XZ
^CI (Change International Font) allows you to substitute characters from different character sets and re-map characters from one code page with x.10 firmware or higher.
For X.8 or higher firmware using the ^CI command to change the character set to Latin 2:
Format: ^CIa
Parameters:
a = Desired Character Set

Example:
^XA ^FO20,70^CI8^A0N,50,50^FD[^FS ^XZ
For X.10 or higher using ^CI command to substitute a character Hex value 131 for a character Hex value 97
Format: ^CIa,s1,d1,s2,d2,…
Parameters:
a = Desired Character Set s1 = source 1 (character position to be remapped) d1 = destination 1 (new position for the character referred to in s1) s2 = source 2 (character position to be remapped) d2 = destination 2 (new position for the character referred to in s1) … = continuation of pattern (up to 156 source and destination pairs may be used).
https://support.zebra.com/cpws/docs/zpl/zpl_spcl_chr.htm

1/2
5/22/25, 11:45 AM
^XA ^CI0,131,97 ^FO20,120^A0N,50,50^FDa^FS ^XZ
support.zebra.com/cpws/docs/zpl/zpl_spcl_chr.htm
Notice: Zebra Technologies Corporation makes no representations about the suitability of this documentation for any purpose. It is provided “as is”, for your information only, without warranty of any kind, either expressed or implied, including, but not limited to, implied warranties of merchantability, fitness for a particular purpose and non-infringement.

Date Updated: 10/09/2010 08:52:26 AM
https://support.zebra.com/cpws/docs/zpl/zpl_spcl_chr.htm
2/2

2025/01/31
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many
jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2024 Zebra
Technologies Corporation and/or its affiliates. All rights reserved.
Information in this document is subject to change without notice. The software described in this document
is furnished under a license agreement or nondisclosure agreement. The software may be used or copied
only in accordance with the terms of those agreements.
For further information regarding legal and proprietary statements, please go to:
SOFTWARE: zebra.com/informationpolicy.
COPYRIGHTS: zebra.com/copyright.
PATENTS: ip.zebra.com.
WARRANTY: zebra.com/warranty.
END USER LICENSE AGREEMENT: zebra.com/eula.
Terms of Use
Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and
maintaining the equipment described herein. Such proprietary information may not be used, reproduced,
or disclosed to any other parties for any other purpose without the express, written permission of Zebra
Technologies.
Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are
subject to change without notice.
Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are
correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and
disclaims liability resulting therefrom.
Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the
accompanying product (including hardware and software) be liable for any damages whatsoever (including,
without limitation, consequential damages including loss of business profits, business interruption, or loss
of business information) arising out of the use of, the results of use of, or inability to use such product, even
if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you
This section provides a high-level overview of the network Set / Get / Do (SGD) commands.
Wireless SGD commands are available in printers with the following firmware versions or later:
• V60.16.2Z or later
• V60.15.xZ or later
• V50.15.xZ or later
• V61.15.xZ or later
• V56.15.xZ or later
• V53.16.x or later
• V53.15.2Z or later
• R53.16.3Z or later
• R60.15.8Z or later
• R62.15.8Z or later
• R63.15.8Z or later
• R65.15.8Z or later
NOTE: The wireless commands listed in this chapter are for use with the Wireless Print Server
and Wireless Plus Print Server, when used with firmware version V60.15.x, V50.15.x, or later.
Wired SGD commands are available in printers with the following firmware versions or later:
• V54
• V66
• V68
• V72
• V73
• V74
• V75
• V76
• V78
• V79
• V60.16.2Z or later
• V60.15.xZ or later
• V50.15.xZ or later
• V61.15.xZ or later
• V56.15.xZ or later
• V53.16.x or later
• V53.15.2Z or later
• R53.16.3Z or later
• R60.15.8Z or later
• R62.15.8Z or later
• R63.15.8Z or later
• R65.15.8Z or late
Documents / Resources
![]() | ZPL2 Printers |
References
- support.zebra.com/cpws/docs/zpl/zpl_spcl_chr.htmsupport.zebra.com
- support.zebra.com/cpws/docs/zpl/zpl_spcl_chr.htmsupport.zebra.com
- zebra.com/id/manualswww.zebra.com
- User Manualmanual.tools

