tuya MX-C10 Automatic Smart Lock Installation Guide

Note:
- This lock is equipped with mechanical keys for manual unlocking. Remove mechanical keysfromthe package and keep them in a safe place and always have access to them.
- To power on the lock, four alkaline AA batteries(not included) are required. Non-alka-lineandrechargeable batteries ARE NOT RECOMMENDED.
- This lock is not designed to be exposed to direct sunlight or rain. It is not waterproof I Prated
- Keep your fingers clean when using this lock.
Please read this manual before operating your Smart Lock, and keep it for further reference.
Components Overview

Front lock x1

Front lock pad x1

Rear lock x1

Rear lock pad x1

Rear lock fixing plate x1

Door opening drawing x1

Lock body x1


Door frame stopper x1

35mm x4 Screw post


![]()
35mm x4 25mm x4 8mm x3

key x3

card x2

Gate magnet x1
Lock Body Overview
Front lock

Rear lock

Specifications
| Material | Aluminum alloy | Model NO. | MX-C10 | |
| Door thickness | 35mm-60mm | Code Length | 4~8 digits | |
| Working Temperature | -20°C~70°C | Working Humidity | 20%~80%RH | |
| Working Power Consumption | <500mA | Static Power Consumption | <50uA | |
| Power Supply | 6V (4pcsAA Alkaline Batteries not included) | |||
| Unlocking Methods | App Access, Fingerprint, Card, Password & Mechanical Key | |||
| User Capacity | 9 Administrators | |||
| Fingerprint (100)/Card (200)/ Password (200) | ||||
| Unlimited App tempera ry passwords | ||||
| Product Dimension | Front | 62(W) x 140(H) x 16.5(D) mm | ||
| Back | 70(W)x 160(H) x 28.5(D) mm | |||
AU specifications are subject to change without notice. All rights reserved.


Installation Guide

Note!
Check the door’s opening direction: if the front body is fastened on the left, turn the toggle button to the L, and if it is fastened on the right, tum it to the R. Make sure the thumb tum towards according to your opening direction
Right-hand door(R)

Left-hand door(L)

Kindly confirm the door’s interior thickness (Must be between38mmto 60mm)

- Keep the bolt closed
- Turn the knob properly: Fig. 1 lf you turned the toggle to R, turn the knob counter clockwise to the end (with the “dot indicator” on the knob oriented left) Fig.2


lf you turned the toggle to L, turn the knob clockwise to the end (with the “dot indicator” on the knob oriented upwards
Note: Before installing back body, please identify right open or left open of the door. Please follow up the below instruction to setup the right open or left open.

Deadbolt Installation
- Adjust the length of the bolt if it is required.

- Install the deadbolt on the door.

- Use a screwdriver to test if deadbolt works smoothly.

- Make sure the bolt in retracted(unlocked) position.


NOTE: The bolt must be in retracted (unlocked) position before installing the lockset.
Lock Body Installation
- Hold the front body to the door, and make sure the key nail piece and cable through the door hole.

- Make sure the cable through the mounting, the position the mounting plate, then fix the front body with three screws.

- Ineart the front body cable through the rectangular hole the rubber pod. Connect the wire connector from the front body through the hole to the back body. Enrsure that the wtre is installed properly and securely.


- After connect the cables, make sure the thumb tum is vertical (Left opening) or horizontal (Right Opening) according to the door opening direction, then hold the back body onto mounting plate.

- Fix the back body to the mounting plate with 3 screws.

- Place the batteries, and make sure the direction of the batteries is correct, the put in the battery cover.

- Drill the strike box and strike plate according to the strike plate and strike box size, then fix them by two screws.

- If you want thelockautomatically lockedafterclose the door, pleaseinstall the door switchsensor.

Intelligent lock(five in one) operation manual
Function and Operation
Description of terms and functional keys
- Administrator information: refer to the Administrator’s fingerprint, password or IC card. Unlock information: refer to the input fingerprint, password, Remote control or IC card information (including Administrator and ordinary users).
- Key”
“: clear key/back key. Enter the password or point by clearing the previous input. Press the clear key three times in succession, empty all input. - Key “
“: confirmation key or menu function key.
Original state
- The factory administrator orinitial password is 123456, under the orinitial state any fingerprint.
IC card or password can open the lock. - Any fingerprint, IC card, or password which are not registered can’t open the lock after inputting the administrator information.
Lock function management (step one)

Administrator settings
- Add administrator (step 2)

- Add administrator information

Common user setting
- Add administrator information

- Delete user information

system setting
- Voice setting

- Unlock mode setting

- Language settings

- Time setting

Restore factory settings

APP Configuration (Tuya Smart)
- Search “Tuya Smart” in App Store or an App market, download and install it.
- Register with your cellphone numberand log in.
- Click “Security & Sensory find Lock(Wi-Fi), click and add a device following instructions before use.
- Remote unlocking: wake up the screen and press “9” + ”
” There will be a voice prompt: requesting remote unlocking.
Add one network
- Press “
”+“
”to authenticate administrator identity and then press “T” to access administrator settings. Then there will be a voice prompt of pressing “3” for network configuration. - Voice prompt in network configuration mode: press 1 for hotspot connection and 2 ^ * for intelligent connection
- When the network is successfully added, the 1, 2, 3 and 4 lights on the keyboard will be on in order with a voice prompt of “operation completed
- In the event of network addition failure, the 1, 2, 3 ^ (a*t_{1}) 4 lights on the keyboard will not be on and there will be a voice prompt of “operation failed” upon timeout
Notice:
- Please add administrator before setting.
Other notes
- Under factory default, input 369
or 1476
to change handle direction - Press the lock key can lock the lock automatically
- Input the wrong password more than 5 times in arow, the keyboard locked for 30 seconds, it does not respond to any operations in 30 seconds
- Password peeping prevention function input password as follows when opening the door with password: XXX password XXX, you can add some extraneous codes before and after the password, and then press fi to confirm. The password must be included in the input contents
- If there is no operation more than 10 seconds, system will automatically exit,
- After the voltage is lower than 4.liv, the lock will automatically alarm every time when it is opened. After the alarm, the lock can be opened for about 200 times.
- Remove the battery cover press the “Set” key for 6 seconds the lock was restored to factory mode;
- In factory mode, input “3336669996
° cna change the language quickly, - When unlocking input “5
” to enter passage mode(One time effective); - When unlocking input “
” to broadcast the user number;
Technical Parameters
| Technical Parameters | |||
| Items | Parameters | Memo | |
| 1 | Static current | ≤50uA | |
| 2 | Dynamic current | ≤500mA | |
| 3 | Administrators number | 9 | |
| 4 | Fingerprint number | 100 | |
| 5 | Fingerprint + password + card capacity | 200 | |
| 6 | Fingerprint Sensor | Semiconductor | |
| 7 | Fingerprint contrast time | ≤0.6Second | |
| 8 | Fingerprint identification Angle | 360° | |
| 9 | False Rejection Rate | ≤0.1% | |
| 10 | False Recognition Rate | ≤0.0001% | |
| 11 | Reaction time | ≤0.1 Second | |
| 12 | Power type | 6V | |
| 13 | Emergency power | 5VDC | |
| 14 | Working temperature | -25°C~60°C | |
| 15 | Working Relative Humidity | 20%~90%RH | |
| 16 | Human voice | Yes | |
| 17 | Keyboard | Touch standard 12-bit keyboard | |
| 18 | Password Length | 4-8 digits | |
| 19 | Phantom password | 32 digits | |
| 20 | Low voltage alarm | 4.6±0.2V | |
| 21 | Unlock time | ≤1 Second | |
MAIN FUNCTION MODULES
LAPP REGISTRATION AND LOGIN
- APP registration: if you do not have an APP account, you can choose to register or log inby SMS verification code.
- Click “create a new account to enter the account registration page. According to the prompt to obtain SMS verification code, set the password.
- If you have an existing account, click “login with an existing account to log in to the APP. Password, verification code, and social account login are supported.


CREATE HOMES
- Create your home after registering and logging in successfully.
- Each account can create and add multiple homes, and devices can be grouped by room in the home.
- Weather and other functions depend on the geographical location of the family, which is recommended to set in advance.

ADD WIFI LOCK
- On the Tab of “my home”, click”+” in the upper right corner to enter the interface in figure 1, select the WiFi door lock in security sensor part and enter the page in figure 2.


- When the device enters the connected mode, continue to operate according to the instructions and APP tips.
HOME PAGE
- Home page includes remote unlock, alarm message, member management, record, temporary password and other functions.
- Remote Unlock: initiate a request from the door lock, and the app can respond to allow / refusal door opening

DYNAMIC PASSWORD
- Click to get the dynamic password Meanwhile copy the password text for you

MESSAGE CENTER
- Message center contains alarm information, doorbell call information and hijacking alarm information, which can be inquired.

USER MANAGEMENT
- User can be added, deleted or changed in member management. Only the administrator user of app is allowed to do that.

RECORD LOG
- 24/7 Record Log, arranged in reverse chronological order. The unlocked ID with the associated user name will directly display the user name, while the unlocked ID without the associated name will display the specific unlock ID

TEMPORARY PASSWORD
- Temporary password can be created and deleted through app. After each create or delete is completed on the app, the lock hardware is required to synchronize with the server.
- At the time of creation, you can choose whether to send SMS or not. Worldwide SMS is supported.


HIJACKING ALARM
- When the anti-hijacking mark in the left picture is opened, if the unlock action of the unlock ID occurs, the record will report and the app will trigger the anti-hijacking alarm

FACTORY DATA RESET
- Click the icon in the upper right corner of the main interface. Find the Factory Data Reset and click
- The Factory Data Reset can also be operated on the lock. Please refer to the instruction manual for details.


FOC WARNING This device complies with part 15 of the FCC Wiles. Operation in subject to the following tan conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause mdesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has heen tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. I however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause haraful interference to radisar television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference hy one or mure of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation hetween the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver in connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FOCIF Exposure guidelines. This equipment should be installed and operated with minimm 20cm distance hetween the radiator and your hody: Use only the supplied antenna.
Documents / Resources
![]() | MX-C10 Automatic Smart Lock |
References
- User Manualmanual.tools



