STAR C102 Clipper Instruction Manual

STAR-logo

STAR C102 Clipper

STAR-C102-Clipper

General safety instructions

Read and observe all instructions, store them in a safe place!

Intended use

  • Only use this appliance for its intended purposes as described in this manual.
  • This appliance is intended for clipping and trimming animal hair, also for light-duty shearing of sheep wool if a special blade set is fitted.
  • This appliance is intended for commercial / professional use.

Requirements on the user

  • Read the operating manual in full and familiarise yourself with it before the first use.
  • Unsupervised use of this appliance is only permitted by adults with appropriate training and knowledge and experience.
  • If they are given supervision and instruction concerning the use of the appliance in a safe way and understand the hazards involved, this appliance may also be used by children aged 14 years and above and persons with reduced physical or sensory or mental capabilities and persons with a lack of experience or knowledge.
  • Children must not play with the appliance. Cleaning and user maintenance must never be carried out by children, unless they are supervised by an adult.
  • Keep the appliance out of reach of children and animals and protected against the effects of the weather.
  • It is recommended that a residual current appliance (RCD) with an operating current of up to 30 mA be installed in the supply circuit. Ask an electrician for advice.
  • Danger! Electric shock due to damaged appliance/mains cable
  • Never use the appliance if it is faulty or damaged or has fallen into water, or if the mains cable or plug is damaged.
  • A damaged mains cable may only be replaced with an original spare part, by an authorised service centre or another similarly qualified person, in order to avoid hazards.
  • Each season before use have your appliance serviced and tested.
  • Only specialists properly trained in the repair of electrical appliances may repair or service this appliance.

Danger! Electric shock due to penetration of liquid.

  • Do not use the appliance near hose-pipes, water-troughs or other water-filled containers. It should also not be used in areas of high humidity.
  • Always position or store electrical equipment where it cannot fall into water. Keep the appliance away from water and other liquids.
  • Never touch electrical equipment that has fallen into water or reach into water to retrieve it. Disconnect from the mains immediately.
  • Have the appliance inspected at a service centre before using it again.
  • Only use and store the appliance in dry places.
  • Never operate the appliance with wet hands.
  • Never use the appliance on a wet animal.

Danger of explosion or fire!

  • Never use the product in an environment with a high concentration of aerosol (spray) products or in which oxygen is released.
  • Do not use aerosol (spray) lubricants / sanitizing solutions, only use the manufacturer‘s lubricating oil.
  • Keep all air openings and filters free from hair and dirt. Never block the air openings. Never operate the appliance on a soft surface which may block the air openings.

Warning! Injuries caused by overheating of blade sets.

  • Cutting blades may become hot after prolonged use.
  • Oil the blades every 5-10 minutes to reduce heating.
  • The blade set can heat up if the appliance is used over a prolonged period. Take regular breaks when using the appliance so that the blade set can cool down.

Warning! Injuries due to incorrect handling.

  • Ensure the appliance switch is in the off (0) position before plugging in and before unplugging.
  • Never leave the appliance unattended when plugged in.
  • Never use blade sets that are broken or damaged or blunt.
  • The blades have fine teeth and the sharp edges may be exposed when they are removed, handle and use with caution.
  • Always switch the appliance off and disconnect from the mains power supply after use and before removing or fitting blades and before cleaning or care or storage.

Warning! Danger of injuries from / to animals.

  • Large animals can cause injuries. Noise from the appliance can startle the animal, causing it to kick or charge. Ensure the animal is calm and properly restrained.
  • Wear personal protective head-wear, eye-wear, ear-protection, footwear, and gloves, as appropriate. Wear close-fitting clothes; removejewellery and tie-up long hair.
  • The animal’s hair / wool must be dry and free from obstructions.
  • Mains cables lying on the ground are a hazard. Ensure that cables cannot snag or be stood on or excreted on.

Caution! Danger of damage to the appliance

  • Only operate the appliance with the voltage stated on the nameplate.
  • Only use accessories or attachments that have been recommended by the manufacturer.
  • Never insert or allow objects to fall into the openings of the appliance.
  • Do not carry the appliance by the mains cable and, when disconnecting the appliance from the mains, always pull the plugrather than the cable or the appliance.
  • Keep the mains cable and appliance away from hot surfaces.
  • Make sure that the mains cable is not twisted or kinked or strained when the appliance is used and stored.

General user information

Information about the operating manual

  • Before using the appliance for the first time, you must read and understand the operating manual completely.
  • Consider the operating manual as partof the product and store it in a safe and accessible place.
  • This operating manual is also available in PDF format to download and print from the manufacturer’s website.
  • The EC declaration of conformity can also be requested in other official EU languages from our service centre.
  • Include this operating manual if passing the appliance on to a third party.

Explanation of symbols and notes

  • DANGER
    Danger of electric shock which may result in serious physical injury or death.
  • DANGER
  • Danger of explosion which may result in serious physical injury or death.
  • WARNING
    Warning of possible physical injury or a health risk.
  • CAUTION

Information about danger of material damage.

  • Note with useful information and tips.
  • Action to be taken by owner.
  • Carry out these actions in the sequence described.

Product description

Accessories (Fig. 1)

  • A. Cleaning brush
  • B. R15 OilSTAR-C102-Clipper-fig-1

Technical data

  • Size (Length): 240mm
  • (Diameter): 50mm
  • Weight: approx. 750g (without cable)
  • Cable length: 5m
  • Blade speed: 2700 rpm
  • Overload current: 0.6 A
  • Emission sound  pressure level: 77.2dB(A) @ 1 m
  • (Uncertainty): 2.5dB(A)
  • Vibration: 4.9 m/s2
  • (Uncertainty): 1.5 m/s2
  • Power consumption: 45W maximum
  • Operating voltage: 220-240 V~ / 50/60 Hz

Operation

Preparation
Keep the case or holdall for safe storage and transportation.

  • Check that the contents are complete.
  • Check all the parts for possible transport damage.
  • Prepare a safe clipping area and all protective equipment.
  • Ensure the animal is safely restrained and that it’s hair is clean and dry.
  • Warning! Injuries and material damage due to incorrect blade fitting.
  • Switch off clipper and disconnect from power source before removing or fitting the blades.
  • Only operate the appliance after the blades have been correctly fitted and tensioned and oiled.STAR-C102-Clipper-fig-2

Fitting the Blades (Fig. 2)

  • Use Lister or Wahl blades for the best fit and performance.
  • Blades are manufactured in pairs, they must be kept and used in pairs to increase their life.
  1. Disconnect from power source.
  2. Turn the clipper upside-down and carefully fit top blade to the clipper head.The crank roller must be located in thesocket of the top blade.
  3. Fit the bottom blade, ensuring the 2  holes are fitted over the 2 pegs.
  4. Insert the tension bolt through the central hole.
  5. Fit the tension spring over the tension bolt, and screw the tension nut down tight.
  6. Set the “Tension” (see below).

Setting the Tension (Fig. 3)

  1. Screw the tension nut down by hand until it stops.
  2. Using the marker on the tension nut as a guide, slacken the tension nut back off by 1 1/2 turns to set the tension.
    Warning! Injuries and material damage due to incorrect tension.
    • Excessive tension will blunt and overheat the blades.
    • Insufficient tension will reduce cutting performance and lead to clogged blades.

Lubrication (Fig. 4)

  • Brush excess hair from the blades and clipper.
  • Oil the blades every 5-10 minutes when clipping, use “R15” oil. Briefly run the appliance to spread the oil, then switch off and wipe away any excess oil.
  1. Oil between the cutter points, pointing the head upwards to spread the oil between the blades.
  2. Oil the surfaces between the clipper head and the top blade.
  3. Oil the heel of the cutter blade from both sides, tilting the head sideways to spread oil over the rear blade surfaces.
  4. Oil the cutter blade guide channels via the two holes, tilting the head sideways to spread the oil.
  5. Oil the crank shaft and roller via the central hole.
    Warning! Injuries and material damage due to incorrect oiling.
  • Oil the blades frequently.
  • Only use “R15” oil. Other lubricants may cause irritation to the animal’s skin.
  • Aerosol spray lubricants contain solvents that may damage the appliance or blades.

Mains operation

  1. Connect the mains plug to the mains socket.
  2. Switch on the appliance by sliding the on/ off switch in the forwards direction.
  3. After use, slide it backwards to switch the appliance off.
    Caution! Damage due to incorrect power supply. Only operate the appliance with the voltage stated on the nameplate.

Overload protection (Fig 5.)
The appliance includes an overload protection fuse that will switch the motor off if the blades become jammed. If the overload protection fuse has activated, check the blades and coat / fleece for blockages. Clear any obstructions and replace any damaged blades. To reset the overload protection fuse, press the reset button situated at the back end of the motor body (B).

Maintenance

Warning! Injuries and material damage due to incorrect handling.

  • Switch off the appliance and disconnect it from the mainsbefore cleaning it or performing any maintenance.
  • It is particularly important to keep plug and cable clean, dry and in order at all times.

Caution! Motor damage due to blockages.

  • The motor will overheat if the filter is blocked.
  • Never run the appliance with the filter removed as hair / wool will enter the motor.
  • Regularly check and clean the filter (6a).
  • Slide the filter out sideways to remove it. Hold it up to the light to check the wire mesh for blockages. Wipe or brush away any dirt and debris. Ensure the filter is clean and dry before refitting.STAR-C102-Clipper-fig-3STAR-C102-Clipper-fig-4

Gear lubrication (Fig. 7)
Every 200 hours running remove the clipper head (1). Wipe the clipper head and gearwheel (2) to remove hair and used grease. Coat the gearwheel with clean grease (Lister R2 or equivalent). When the clipper head is removed, check the gearwheel for wear and broken teeth. Refit the clipper-head before operating.

Cleaning & storage
Danger! Electric shock due to penetration of liquid.

  • Do not immerse the appliance in water, do not allow any liquid toget inside the appliance.
  • Only connect the appliance to the  power supply if it’s completely dry.
  • Caution! Damage from aggressive chemicals.
  • Never use solvents or scouring agents, as aggressive chemicals could damage the appliance and accessories.
  • Only wipe the appliance with a soft, slightly damp cloth.
  • Wipe the handle with a soft cloth. Use a brush to remove hair and dirt from the blades and clipper-head.
  • Remove the blades for cleaning. Care should be taken not to lose the tension spring. Oil the blades before storage.
  • Store in a clean, dry, safe place.

Servicing and repairs
If the cutting performance deteriorates, the blades should be re-sharpened or replaced. Accessories and spare parts are available from your dealer or our service centre. Only specialists properly trained in the repair of electrical appliances may repair or service this appliance.

Disposal
Handle with care! Environmental damage in the event of incorrect disposal.

  • Correct disposal will ensure environmental protection and prevent any potentially harmful impact on people and the environment.
  • Adhere to the relevant legal requirements when disposing of the appliance.

Information on the disposal of electrical and electronic appliances in the European Community:

  • Within the European Community, national regulations are specified for the disposal of electrical appliances, based on EU Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). In accordance with this, the appliance can no longer be disposed of with the local or domestic waste.
  • The appliance will be accepted free of charge by local collection points or recycling centres.
  • The packaging for this product is made from recyclable materials.
  • Dispose of this in an environmentally friendly manner by recycling it.

Documents / Resources

PDF thumbnailC102 Clipper
Instruction Manual · 109-10983, C102 Clipper, C102, Clipper

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.