
Installation Guide
VIGI Solar System Controller
© 2024 TP-Link 7106511595 REV1.0.1
Chapter 1 Overview
The VIGI Solar System Controller should work with VIGI 180W Solar Mount, and VIGI Solar Panels.
Open the waterproof box with the provided key and the solar system controller is shown as below.

Note: Keep the key in a safe place for future use.
- Modular Battery*3
- Controller LED
- Explosion-proof Valve: Used to help discharge the exhaust gas in the waterproof box when the battery explodes to ensure safety.
- Three-pin female connector for connecting the controller
- Three-pin male connector for connecting the modular battery
- Four-pin female connector for connecting the solar panel
- RJ45 Network interface for connecting network devices such as 4G routers and bridges
- Load Interface for connecting cameras
Load Interface #1: 9-12.6VDC
Load Interface #2: 9-12.6VDC
Load Interface #3: 12VDC
• Controller LED
| LED | Indication |
| SYS | On: The system is working and the load is enabled Flashing: The system is working and the load is disabled. Off: The system is not working. |
| LAN | On: The RJ45 interface is connected. Flashing: Data is being transferred. Off: The RJ45 interface is not connected. |
| PV | On: PV panels are connected and have voltage. Off: PV panels have no voltage. |
| BAT1/2/3 | On: Battery power is higher than 20%. Slow Flashing: Battery power is lower than 20%. Off: Battery is abnormal. |
Chapter 2 Installation
2.1 Package Contents
Make sure that the package contains the following items. Please contact your distributor, if any of the listed items are damaged or missing.
The figures are for demonstration only. The actual items may differ in appearance and quantity from what is depicted.

2.2 Safety Precautions
- During installation, collision and knocking are strictly prohibited to avoid damage.
- When placing the modular battery, make sure that the solar panel is facing upwards and placed horizontally. Uneven ground may scratch or damage the solar panel.
- Make sure there are no fixed obstructions. If installed around buildings or trees, it is necessary to ensure the installation height of the battery panel is higher than the obstacle.
- All modular battery load interfaces should take strict waterproof measures to avoid short circuit, leakage, and other problems.
Step 1. Prepare all components
The VIGI Solar System Controller should work with VIGI 180W Solar Mount, and VIGI Solar Panels.
Step 2. Install the solar mount



Step 3. Install the solar panel



Recommended solar panel inclination angles (the following inclination angles correspond to the holes on the mount):
| Latitude Range | Recommended Inclination |
| 0-5° | 5° |
| 5 -15° | 15° |
| 15-25° | 25° |
| 25-35° | 35° |
| 35-45° | 45° |
| >45° | 55° |
Step 4. Install the solar system controller



Step 5. Install the cameras

Note: If the product is used in a windy area, it is recommended to tie VIGI 5-Series cameras directly to the pole to reduce the impact of strong wind on the image quality of the camera.
Step 6. Connect the cables

Step 7. Waterproof cables
- After connecting the camera to the load interface, wrap the connection with over two layers of waterproof tape (not included).
Note: When using waterproof tape, wrap the first layer, then cut. Apply a second layer, ensuring no gaps between the connection and tape for secure waterproofing. - Install the waterproof cable attachments for the network interface.
Note: Make sure each part is securely attached and the waterproof rings are flush to keep out water.

Chapter 3 Configuration
Here is a typical network topology for the VIGI solar system controller.

- Connect the RJ45 network interface of the controller to the network devices (such as access points, bridges, and 4G cameras).
- Download and install the latest TP-Link VIGI app.
https://www.tp-link.com/app/qrcode/?app=vigi - Open the app and log in with your TP-Link ID. If you don’t have an account, sign up first.
- Tap the + button on the top right and follow the app instructions to add the VIGI solar system contrroller. Then you can control and manage the VIGI solar system controller via the VIGI app remotely.
Appendix FAQ
Q1. The controller LED status is abnormal. Q2. Short system runtime and short monitoring time.
Safety Information
- Do not attempt to disassemble, repair, or modify the device.
- Do not use damaged charger or USB cable to charge the device.
- Do not use any other chargers than those recommended.
- Adapter shall be installed near the equipment and shall be easily accessible.
- Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don’ t hesitate to contact us.
- Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
- Place the device with its bottom surface downward. Install it at stable places, and prevent it from falling.
- Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid.
This equipment is not suitable for use in locations where children are likely to be present. This equipment is not suitable for use in locations where children are likely to be present, such as family environment, school, children’s playground and so on.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a safeguard.
Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
Do not leave a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
CAUTION!
Risk of fire or explosion if the battery is replaced by an incorrect type.
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca/
For technical support, user guides and other information, please visit https://www.tp-link.com/support/
![]()
Documents / Resources
![]() | PS90 Solar System Controller |
References
- CE Regulatory Compliance | TP-Linkwww.tp-link.com
- TP-Link Product Support - Wireless Networking Equipment Supportwww.tp-link.com
- Regulatory Compliance | TP-Linkwww.tp-link.com
- User Manualmanual.tools
