SINGER 8763 Sewing Machine

Product Information
Specifications
- Model: 8763
- Electric Appliance: Sewing Machine
- Power: DC 6.5 V, 2.8 Watts
- Intended Use: Household
Product Usage Instructions
Safety Instructions
When using the sewing machine, follow these safety precautions
- Never leave the machine unattended when plugged in.
- Always unplug the machine after use and before cleaning.
- Unplug before replacing the light bulb.
- Do not allow children to use the machine unsupervised.
- Use only recommended attachments.
- Do not operate if the machine is damaged.
- Switch off before servicing or maintenance.
Foot Control
For users in the USA and Canada, use the Yamamoto Electric, Model YC-485 EC foot control with this sewing machine.
Polarized Plugs Caution
In the USA and Canada, the machine has a polarized plug. Ensure it fits correctly into a polarized outlet. Do not modify the plug.
Recycling Information
This equipment complies with recycling requirements. Dispose of it separately at an appropriate collection point to benefit the environment.
FAQ
- Q: What type of light bulb should I use for replacement?
- A: Replace the bulb with a DC 6.5 V, 2.8 Watts bulb of the same type.
- Q: Can children use this sewing machine?
- A: Children should only use the sewing machine under close adult supervision.
“IMPORTANT SAFETY INSTRUCTIONS”
“When using an electrical appliance, basic safety precautions should always be followed, including the following.” “Read all instructions before using this sewing machine.”
“DANGER–To reduce the risk of electric shock:”
- “This sewing machine should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning.”
- “Always unplug before replacing light bulb. Replace bulb with same type rated DC 6.5 V 2.8 Watts.”
“WARNING– To reduce the risk of burns, fire, electric shock, or injury to persons: ”
- “Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children.”
- “Use this sewing machine only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as contained in this manual.”
- “Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped
or damaged, or dropped into water. Return the sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment.” - “Never operate the sewing machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot control free from the accumulation of lint, dust, and loose cloth.”
- “Never drop or insert any object into any opening.”
- “Do not use outdoors.”
- “Do not operate where aerosol (spray) products are being used or where oxygen is being administered.”
- “To disconnect, turn switch to the off (“0”) position, then remove plug from outlet.”
- “Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.”
- “Keep fingers away from all moving parts. Special care is required around the sewing machine needle.”
- “Never sew with a damaged needle plate as this can cause a needle to break.”
- “Do not use bent needles.”
- “Do not pull or push fabric while stitching. It may deflect the needle causing it to break.”
- “Switch the sewing machine off (“0”) when making any adjustments in the needle area, such as threading needle, changing needle, threading bobbin, or changing presser foot, etc.”
- “Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual.”
“CAUTION– Moving parts-To reduce risk of injury, switch off before servicing. Close cover before operating machine.”
“SAVE THESE INSTRUCTIONS”
“This product is for household use, or equivalent.”
FOOT CONTROL (USA & Canada only)
Use Yamamoto Electric, Model YC-485 EC with this sewing machine.
POLARIZED PLUGS CAUTION (USA & Canada only)
This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended
to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.
This appliance complies with EEC Directive 89/336/EEC covering the electromagnetic compatibility.
This equipment is marked with the recycling symbol. It means that at the end of the life of the equipment you must dispose of it separately at an appropriate collection point and not place it in the normal domestic unsorted waste stream. This will benefit the environment for all. (European Union only)
SINGER® is a registered trademark of The Singer Company Ltd or its affiliates.
Copyright © 2007
All Rights Reserved.
KNOWING YOUR SEWING MACHINE
MACHINE IDENTIFICATION
- Thread guide
- Thread tension control
- Threading lever
- Face cover
- Thread cutter/holder
- Extension table (Accessory box)
- Bobbin winder shaft
- Bobbin winder stop
- Reverse stitch button
- Horizontal spool pin
- Handle
- Hand wheel
- Power/light switch
- Cord socket
- Identification plate
- Presser foot lifter
- Buttonhole lever
- Twin thread guide
- Thread guide
- Presser foot screw
- Needle
- Bobbin cover plate
- Needle bar
- Alternate thread cutter
- Foot release button
- Needle clamp screw
- Presser foot
- Feed dogs
- Needle plate
- Bobbin cover release button
- Power line cord
- Foot control
- Instruction manual

ACCESSORIES
- Needles
- Bobbins (4 total – 1 in machine)
- Auxiliary spool pin
- Spool pin felt discs (2)
- Spool pin cap (small)
- Spool pin cap (medium)
- Spool pin cap (large)
- Buttonhole opener/Seam Ripper and Brush
- Screwdriver for needle plate
- Darning plate
- Zipper foot
- Satin stitch foot
- Blind stitch foot
- Buttonhole foot

The Foot that comes on your Sewing machine is called the General Purpose Foot and will be used for the majority of your sewing.
The Satin Foot (12) is another very useful foot and should be used for most of your decorative sewing.
When purchasing additional bobbins, be sure they are Class I5 J.
SETTING UP YOUR MACHINE
Be sure to wipe off any surplus oil from needle plate area before using your machine the first time.

POWER LINE CORD/FOOT CONTROL
Connect the plug of the power line cord into the cord socket (1) and your wall outlet (2) as illustrated.
Connect the foot control plug (3) into the machine socket.
NOTE: When foot control is disconnected, the machine will not operate.
Always disconnect the machine from power supply by removing the plug from the wall-outlet.
POWER/LIGHT SWITCH
Your machine will not operate until the power/light switch is turned on. The same switch controls both the power and the light.
When servicing the machine, or changing needles, etc., machine must be disconnected from the power supply.

SPOOL PINS
HORIZONTAL SPOOL PIN for normal thread spool
Place thread spool on the pin and secure with a spool cap to ensure smooth flow of thread. If the thread spool has a thread retaining slit, it should be placed to the right.
Select the correct spool pin cap according to the type and diameter of spool being used. The diameter of the spool pin cap should always be larger than that of the spool itself.

VERTICAL SPOOL PIN for large thread spool
Attach the spool pin. Place the large spool pin cap and felt disc over it. Place a thread spool on the spool pin.
PRESSER FOOT LIFTER
There are three positions for your presser foot.
- Lower the presser foot to sew.
- Raise the lifter to the middle position to insert or remove fabric.
- Lift it to its highest position to change the presser foot or to remove thick fabric.
DARNING PLATE
Use the darning plate when you need to control fabric feeding for button sewing, free motion work and free motion darning.
Raise needle and presser foot, and position darning plate onto the needle plate with the two pins on the back inserted to the holes of needle plate.
CONVERTING TO FREE-ARM SEWING
- Your machine can be used either as a flat- bed or as a free- arm model.
- With the extension table in position, it provides a large working surface as a standard flat-bed model.
- To remove the extension table, hold it firmly with both hands and pull it off to the left as shown. To replace, slide the extension table back into place until it clicks.
- With the extension table removed the machine converts into a slim free-arm model for sewing children’s clothes, cuffs, trouser legs, and other awkward places.
WINDING THE BOBBIN
Be sure to use Class 15 J bobbins.
- Place a spool of thread on the spool pin, and secure it with the spool pin cap. Pull the thread out from the spool and place it through thread guides as shown in illustration.
- Put end of thread through the hole in bobbin as shown.
- Push bobbin winder shaft to far left position, if it is not already there. Place bobbin onto shaft with end of thread coming from top of bobbin. Push bobbin winder shaft to the right until it clicks. Hold onto end of thread.
- Start machine. After the bobbin has begun to fill, stop to cut the thread tail. Step on the foot control again to continue to fill the bobbin. The bobbin will automatically stop turning when completely filled. Push shaft to the left to remove bobbin and cut thread.

THREADING THE BOBBIN THREAD
- Raise the needle to its highest position by rotating the hand wheel counter clockwise.
- Remove the bobbin cover plate by pushing the release button to the right. Bobbin cover will pop up sufficiently to allow you to remove the cover.
- Insert the bobbin making sure the bobbin rotates counter- clockwise when you pull the thread.
NOTE: This is a very important step. The bobbin must rotate counterclockwise when thread is pulled. - Pull thread through the slot (A) and then to the left.
- With a finger held gently on top of the bobbin, pull the thread until it stops in the slot (B). Then pull the thread along the groove on the needle plate until it is snipped with cutter on the top left.
NOTE: Sewing can be started without picking up the bobbin thread. - Replace the clear bobbin cover plate onto the needle plate.

THREADING THE TOP THREAD
- Raise the presser foot lifter. Always be sure to raise the presser foot lifter before threading the top thread. (If the presser foot lifter is not raised, correct thread tension cannot be obtained.)
- Turn the hand wheel counter clockwise until the needle is in its highest position.
- Thread the machine with your left hand while firmly gripping the thread with your right hand in the following order as illustrated.
- Guide the thread through thread guides (1 & 2), and then pull it down along the groove (3).
- Guide the thread into the thread guide (4).
- Pass the thread through the eye of the needle (5) from front to back. (See following page for instructions on operation of the Automatic Needle Threader.)

IMPORTANT
To verify that the machine is threaded properly in the tension discs, do this simple check
- With the presser foot raised, pull the thread towards the back of the machine. You should detect only a slight resistance and little or no deflection of the
needle. - Now lower the presser foot and again pull the thread towards the the back of the machine. This time you should detect a considerable amount of resistance and much more deflection of the needle. If you do not detect the resistance you have mis-threaded the machine and need to re-thread it.
USING AUTOMATIC NEEDLE THREADER
* Be sure to raise the presser foot lifter and raise the needle to its highest position before threading.

NOTE: For smooth threading, it is recommended that the machine be set for straight stitch (in center needle position) when using the automatic needle threader.
- Hook thread to the thread guide on the needle bar and pull it toward you leaving about 4” (10 cm) clear.
- Hook thread to the twin thread guide (A and B).
- Pull thread gently into the thread cutter/holder to cut and hold it in place.
NOTE: Don’t pull thread with strong force or thread may be pulled off from needle hole after threading. - Pull down the threading lever until the twin thread guide rotates and stops.
NOTE: Make sure that the guide doesn’t touch fabric, etc. - Release the threading lever and needle will be threaded automatically. If it should not return to the original position, raise it gently by hand
- Pull thread loop away from you.

Note
- Heavy thread cannot be threaded through fine needle.
- Don’t lower the threading lever while the machine is in operation or the threading hook may be broken.
- Put a drop of sewing machine oil onto the felt disc, if the machine is used after a long interval.
- If the threading hook is deviated from needle hole, adjust the position of the hook.
NEEDLE, THREAD AND FABRIC CHART
Your fabric will determine the choice of a needle and thread. The following table is a practical guide to needle and thread selection. Always refer to it before a new sewing project. Be sure to use the same size and type of thread in the bobbin as in the top thread supply.
| FABRICS | THREAD | NEEDLES | |
| The fabrics below can be of any fiber: cotton, linen, silk, wool, synthetic, rayon, blends. They are listed as examples of weight. |
TYPE |
SIZE |
|
| Light- Batiste
Weight Chiffon Crepe |
Cotton-wrapped Polyester
100% Polyester * Mercerized Size 60 |
2020
red shank |
11/80
orange band |
| Medium- Corduroy | Cotton-wrapped | 2020 | 14/90 |
| Weight Flannel | Polyester | red | blue |
| Gabardine | 100% Polyester | shank | band |
| Gingham | * Mercerized Size 50 | ||
| Linen | Nylon | ||
| Muslin | |||
| Wool Crepe | |||
| Medium- Bonded Wovens | Cotton-wrapped | 2020 | 16/100 |
| Heavy Canvas | Polyester | red | purple |
| Coating | 100% Polyester | shank | band |
| Denim | * Mercerized Size 40 | ||
| Duck | * “Heavy Duty” | 18/110 | |
| Sailcloth | yellow
band |
||
| Knits Bonded Knits | Cotton-wrapped | 2045 | 11/80 |
| Double Knit | Polyester | yellow | orange |
| Jersey | Polyester | shank | band |
| Tricot | Nylon | 14/90 | |
| blue | |||
| band | |||
| 16/100 | |||
| purple | |||
| band | |||
- Do not use on stretch fabrics.
- For best sewing results, always use a Singer Branded Needle.
Always disconnect the machine from power supply by removing the plug from the wall-outlet.
Changing the needle
- Raise the needle bar to its highest position by turning the hand wheel counter clockwise.
- Loosen the needle clamp screw by turning it counter clockwise.
- Remove the needle by pulling it downward.
- Insert the new needle into the needle clamp with the flat side toward the back.
- Push the needle up as far as it can go.
- Tighten the needle clamp screw with the screw driver.
NOTE: Tighten snugly, but do not over tighten.
Helpful Hint: Placing a scrap of fabric under the presser foot and lowering the presser foot makes it easier to change the needle and will preclude dropping the needle into the needle plate slot.

ADJUSTING TOP THREAD TENSION
90% of your sewing will be accomplished with the word “AUTO” exposed on the tension control dial on top of the machine.
Helpful Hint: A slight adjustment to a higher number or a lower number may improve sewing appearance.
STRAIGHT STITCHING
- The correct appearance of your stitching is largely determined by the balanced tension of both top and bobbin threads. The tension is well balanced when these two threads ‘lock’ in the middle of layers of the fabric you are sewing.
- If, when you start to sew, you find that the stitching is irregular, you will need to adjust the tension control.
- Make all adjustments with presser foot ‘down’.
- A balanced tension (identical stitches both top and bottom) is usually only desireable for straight stitch sewing.
ZIG ZAG and DECORATIVE SEWING
For zigzag sewing and decorative stitch functions, thread tension should be less than for straight stitch sewing.
You will always obtain a nicer stitch and less puckering when the upper thread appears slightly on the bottom side of your fabric.
BOBBIN TENSION
The bobbin tension has been correctly set at the factory, so you do not need to adjust it.

CHANGING PRESSER FOOT
Be sure needle is in the up position. Raise presser foot lifter.
- Push presser foot release button to remove the foot.
- Place the desired foot on the needle plate aligning the presser foot pin with the foot holder.
- Lower the presser foot lifter so that the foot holder snaps on the foot.

NOTE: The provided scales and numbers on the length and width controls are for reference only and do not represent actual sewing parameters of length and width.
CONTROL PANEL FUNCTIONS
Pattern selection buttons
Turn on the power switch and the LED indicator above the straight stitch pattern will be lit. At this point you may sew Straight Stitch.
To select other patterns, push the pattern selection button to the right of the row that contains your desired pattern. Stop when the LED indicator above your pattern is lit.
Stitch length and width/needle position controls
- Your sewing machine will produce most of your stitching requirements at an Auto/Default Stitch Length and Width. When a pattern is selected, it will automatically sew at default settings of stitch length, width and needle position for straight stitch.
- Auto (preprogrammed) default settings are easily determined by moving the Stitch Length and Width / Needle Position Control Knob. The LED Indicator next to the Control will light without blinking and a beep will sound indicating you are at the Auto / Default Position.
- Once you have determined the Auto / Default position you can manually change the length, width or straight stitch needle position according to your preference. Starting at the Auto position, slide the control knob left or right to locate each of the potential adjustments. At each manual adjustment point, the LED will blink 3 times and a beep will sound.
Note: Instructions for manually changing the Straight Stitch Needle Position are contained in the “Other Information” Section.
Notes
- Some patterns offer more options for manual adjustments than others.
- An alternate method of determining available adjustments is to move the control knobs while sewing slowly.
REVERSE OPERATION BUTTON
Dual purpose reverse/tacking stitch button
- Reverse stitch function for straight and zigzag stitches
Reverse sewing is carried out while the reverse stitch switch is pushed.
The machine will continue to sew in reverse as long as the reverse switch button is pressed. - Tacking stitch function for tie-off of other stitches
The sewing machine makes 4 tiny tacking stitches to tie off the sewing on all patterns except straight and zigzag stitches. The position of the tacking stitches will be at the exact spot in the pattern where the reverse/tacking stitch button is pushed.
NOTE: This function is very useful for tying off the sewing pattern to avoid raveling at the start and end of sewing.

STARTING TO SEW QUICK REFERENCE TABLE OF STITCH LENGTH AND WIDT

STRAIGHT STITCHIN![]()
Straight stitch is most frequently used for all types of sewing. Let’s begin by following the steps below.

- SETTINGS
Presser foot – General Purpose Foot
Thread tension control – AUTO
NOTE: Based upon the weight of the fabric, slight “fine tuning” of the tension may be desired.- Thread tension control
- Reverse stitch switch
- Presser foot lifter
- Stitch length control
- Needle position control
NOTE: Since a straight stitch has no width, the stitch width control is used to change the needle position.
- Pull both threads under the presser foot toward the back of the machine, leaving about 6” (15cm) clear.
- Place the fabric under the presser foot and lower the presser foot lifter.
- Turn the hand wheel counter clockwise until the needle enters the fabric.
- Start the machine. Guide the fabric gently with your hands. When reaching the edge of the fabric, stop the sewing machine.
NOTE: The Needle Plate has both Metric and Inch Markings as an aid for guiding your fabric when sewing a seam. - First turn the handwheel counter clockwise until the needle is at its highest position, then raise the presser foot, draw the fabric to the rear and cut off excess threads with the thread cutter located on the top of face cover as shown.
NOTE: To secure the stitching and avoid raveling, press the reverse stitch button and sew a few stitches at the start and end of the seam.
KEEPING SEAMS STRAIGHT
To keep the seam straight, use one of the numbered guide lines on the needle plate. The numbers indicate distance from the needle at its center position.
The guide line on the bobbin cover plate is 1/4″ (6mm) seam guide line which is used for piecing quilt blocks and also for narrow seams, such as those in doll clothes or baby garments.
INSERTING ZIPPERS AND PIPING
Use zipper foot to sew to the right or left of the zipper or to sew close to the cording.
INSERTING ZIPPERS
- To sew down the right side, attach left side of zipper foot to presser foot holder so that the needle passes through the opening on the left side of the foot.
- To sew down the left side, attach right side of foot to foot holder.
PIPING
- To pipe soft furnishings, cover cord with a bias strip of fabric and pin or tack it to the main piece of fabric.
- Attach right side of zipper foot to foot holder so that needle passes through the opening on the right side of the foot.
Helpful Hint: Slight adjusting of the needle position to sew closer to the piping may be accomplished with the Stitch Width Control

HAND-LOOK QUILT STITCH
This stitch is designed to look like hand sewing for topstitching and quilting.
- Thread bobbin with desired top stitching color. When sewing the machine will pull this thread to the top.
- Thread machine with invisible or lightweight thread that matches your fabric. This thread should not show.
- Increase thread tension a little at a time and continue until you achieve the desired appearance.
- Start to sew.
NOTE: For a dramatic appearance, experiment with different tension and stitch length combinations.
ZIGZAG STITCHIN
SETTINGS :Presser foot – General Purpose Foot :
Thread tension control – AUTO
The top thread may appear on the bottom depending on the thread, fabric, type of stitch and sewing speed, but the bobbin thread must never appear on the top of the fabric.
If bobbin thread is pulling to the top or you are experiencing puckering, slightly reduce the tension with the Thread Tension Control.
ADJUSTING STITCH WIDTH AND LENGTH
Dark grey box indicates the Auto/default value set automatically when the pattern is selected.
For the Zigzag Pattern the stitch length is 2 mm and the stitch width is 5 mm.
The light grey boxes indicate all the possible personal preference options available to set manualy.
NOTE: The values shown in the chart are actual sewing lengths and widths and do not correspond to the scale and number markings on the sewing machine.
SATIN STITCH
This is a closely spaced zig zag stitch used for appliqué, bar-tacking, etc. Slightly loosen the top thread tension and manually adjust the stitch length between 0.5 and 2.0 for satin stitching.
Use a backing of stabilizer for sheer fabrics to avoid puckering.
NOTE: When sewing a dense (closely spaced) Satin Stitch, the Satin Stitch Foot MUST be used.
PLACEMENT OF PATTERNS
Stitch width of pattern increases from center needle position as illustrated.
BLINDHEM STITCH
The blindhem stitch is primarily used for hemming curtains, trousers, skirts, etc.
Settings : Presser foot – Blind Stitch Foot
Thread Tension Control: AUTO
– Regular blind stitch for normal woven fabrics
– Elastic blind stitch for soft, stretchable fabrics
- With matching thread finish the raw edge. On fine fabric, turn up and press a small ½” or less hem. On medium to heavyweight fabrics overcast the fabric’s raw edge.
- Now fold the fabric as illustrated with the wrong side up.
- Place the fabric under the foot. Turn the handwheel counter clockwise by hand until the needle swings fully to the left. It should just pierce the fold of the fabric. If it does not, adjust the guide (B) on the Blindhem Foot (A) so that the needle just pierces the fabric fold and the guide just rests against the fold.
NOTE: In addition to the adjustment on the foot, the stitch width control can be used. The stitch width control changes the swing of the needle for a more narrow or wider stitch.
Sew slowly, guiding the fabric carefully along the edge of the guide. - When completed, the stitching is almost invisible on the right side of the fabric.
NOTE: It takes practice to sew blind hems. Always make a sewing test first.
MULTI-STITCH ZIGZA

SETTINGS :Presser foot – General Purpose Foot
:Thread tension control – AUTO
- This is a strong stitch because as its name implies, it makes three short stitches where the normal zig-zag makes only one.
- For this reason it is highly recommended for overcasting all types of fabrics.
- It is also ideal for bartacks, mending tears, patching, sewing toweling, patch-work and attaching flat elastic.
NOTE: Mending a tear or overedging as shown in illustration requires manual adjustment of the length control.
STRETCH AND DECORATIVE STITCHES

SETTINGS :Presser foot – General Purpose Foot or Satin Stitch Foo
Thread tension control – AUTO
Stretch stitches are mainly for use on knit, or stretchable fabrics, but can also be used on woven fabrics.
STRAIGHT STRETCH STITC![]()
- Straight stretch stitch is far stronger than an ordinary straight stitch because it locks three times – forwards, backwards and forwards.
- It is particularly suitable for reinforcing the seams of sportswear in stretch and non-stretch fabrics, and for curved seams which take a lot of strain.
- Use this stitch also to top-stitch lapels, collars and cuffs to give a professional finish to your garments.
RIC-RAC STITCH![]()
Ric-rac is primarily used for a decorative top-stitch. It is ideal for edging neck-bands, armholes, sleeves and hems. When manually adjusted to a very narrow width it also can be used for seaming in areas of great stress.
HONEYCOMB STITCH![]()
The Honeycomb stitch is ideal for smocking and useful for overcasting and attaching elastic and stretch lace.
- Make several rows of gathers across the fabric that you wish to smock.
- With a narrow strip of fabric directly under the line of gathering, stitch over the gathers. The design will be a series of small diamonds.
OVEREDGE STITCH![]()
This is a similar stitch used by the garment industry in making sportswear – it forms and finishes the seam in one operation.
It’s very effective for use in repairing raw or worn edges of garments.
FEATHER STITCH![]()
The pleasing appearance of this stitch enables it to be used for top stitching, or attaching lace or inset panels when making lingerie.
It is also ideal for quilting applications and Joining fabrics.
PIN STITCH![]()
The Pin stitch is a traditional stitch pattern used for picot-like edges and for applique work.
BLANKET STITCH![]()
The Blanket stitch is traditionally a hand embroidery stitch used to put bindings on blankets. This multi-purpose stitch can also be used for attaching fringe, attaching edgings, couching, applique and drawn thread hemstitching.
LADDER STITC![]()
- The Ladder stitch is primarily used for drawn thread hemstitching. It can also be used for sewing over thin tape in an opposite or same color. Place the stitch in the center and a special effect will be obtained for decoration.
- Another use for the ladder stitch is couching over narrow ribbon, yarn or elastic.
- For drawn thread work, choose a coarse linen type fabric and after sewing draw the thread out within the ladder for an open airy appearance.



SLANT PIN STITCH![]()
Excellent for hemstitching table and bed covers with an elegant touch. Picot-like stitch can also be made on sheer materials. Sew along the raw edge of fabric and trim close to the outside of the stitching.
SLANT OVEREDGE STITCH![]()
Seams and overcasts in one operation to produce a narrow, supple seam, particularly suited to swimwear, sportswear, T-shirts, babywear in stretch nylon, stretch towelling, jersey and cotton jersey.
GREEK KEY STITCH![]()
A traditional pattern suited for decorative borders, hems and edge finishings.

ENTREDEUX STITCH![]()
Useful for decorative stitching on borders and for use in heirloom sewing. The Entredeux stitch is most often sewn with a Wing Needle (Singer Style 2040) to create holes in the stitch pattern.
Helpful Hint: A slight + adjustment of the tension will increase the size of the hole when using a Wing Needle.
DOUBLE OVERLOCK STITCH
The Double overlock stitch has three main uses. It is perfect for attaching flat elastic when making or repairing lingerie, for overcasting, and for seaming and overcasting in one operation. It is primarily used on slightly stretch fabrics and non-stretch fabrics such as linen, tweed, and medium to heavy-weight cotton.
CRISS-CROSS STITCH![]()
Used to sew and finish stretch fabrics or for decorative stitching, such as when creating a border.
CROSSED STITCH![]()
Use to sew and finish elastic fabrics or for decorative stitching.

DECORATIVE DESIGNS
SETTINGS :Presser foot – Satin Stitch Foot
Thread tension control – AUTO
- Always practice on a scrap of the actual fabric from your project.
- Before starting to sew, check that there is enough thread wound onto the bobbin to make sure that the thread will not run out during sewing.
- Slightly loosen top thread tension.
Helpful Hint: For a more pleasing appearance experiment with a slightly lower (-) Tension setting.
IDEAS ON DESIGN STITCHING
Crescent pattern on collar
This is an ideal decorative stitch for the sleeves and collars of ladies’ and children’s clothes, and also for table linen edges.
When using this stitch pattern for table linen edges, first sew the stitch and then trim the edge of the fabric along the edge of the stitch. Be careful not to cut the stitch at this time.
Pyramid on bias tape
Use bias tape and fold back the edge. Sew the pyramid pattern on top of this.
Arrowhead on lapel
In addition to using this pattern as a decorative stitch, it can also be used as a triangular backtack stitch for reinforcing places which can easily unravel. This is particularly useful for sewing both edges of pockets.

CONTINUOUS PATTERNS
SETTINGS :Presser foot – General Purpose Foot or Satin Stitch Foot
:Thread tension control – AUTO
These are the optimum patterns for sewing continuous patterns often seen on borders or hems of garments and home decorating projects. Use whichever patterns suit your preference.

SEWING ON A BUTTON![]()
SETTINGS :Presser foot – General Purpose Foot :Darning plate
Position your fabric and button under the presser foot. Lower presser foot. Turn the handwheel to make sure needle clears both left and right openings of button. Adjust width if required. Sew 10 stitches.
If a button shank is required, place a darning needle on top of the button and sew over top of it as illustrated.
Helpful Hint: To secure thread, pull both threads to the backside of the fabric and tie together.

SEWING A BUTTONHOLE
USING BUTTONHOLE FOOT
Your machine offers you two different widths of bartack buttonholes sewn by a system that measures the size of the button and calculates the size buttonhole required. All of this is done in one easy step.
PROCEDURE
- Use an interfacing in the area of the garment where buttonholes are placed. Stabilizer or regular interfacing can be used.
- Make a practice buttonhole on a scrap of the actual fabric from your project. Then try the buttonhole with your button.
- Select one of buttonhole patterns.
- Replace the presser foot with the buttonhole foot. (Refer to “Changing presser foot” on page 24 – 25.)
- Insert the button into the buttonhole foot. (Refer to “Using buttonhole foot” above.)
- Lower the buttonhole lever (C) so that it drops down vertically between the stoppers (A) and (B).

- Carefully mark the position of buttonhole on your garment.
- Place the fabric under the foot. Pull out the bobbin thread underneath the fabric to a length of about 4 inches to the rear.
- Align the buttonhole mark on the fabric with the mark on the buttonhole foot, and then lower the buttonhole foot.
- While holding the top thread, start the machine.
* Sewing will be completed automatically in the following order. - When sewing is finished, use a buttonhole opener/seam ripper to open up the fabric in the center of the buttonhole. Be careful not to cut any of the stitching.


CORDED BUTTONHOLES
- Hook filler cord (crochet thread or buttonhole twist) over the spur and pull both ends of the cord forward under the foot and tie off the cord as shown in the illustration.
- Sew buttonhole so that zigzag stitches cover the cord.
- When completed, release the cord from foot and snip off extra length.

CARING FOR YOUR MACHINE
CLEANING HOOK AREA AND FEED DOGS
CAUTION
Always disconnect the machine from power supply by removing the plug from the wall-outlet
To ensure the best possible operation of your machine, it is necessary to keep the essential parts clean at all times.
- Raise the needle to its highest position.
- Remove two screws on the needle plate (1) and slide the needle plate toward you as illustrated for removal.
- Remove the bobbin case (2).
- Clean the feed dogs and hook area with the lint brush. Put one drop of sewing machine oil on the hook race as indicated by the arrows. (A, B)
NOTE: Singer Brand Sewing Machine Oil is suggested. DO NOT use “all purpose” oil as it is not suited for sewing machine lubrication - Replace the bobbin case with the projection (3) positioned against the spring (4).
- Make sure that the needle is at its highest position and put and slide the needle plate into position as illustrated.

OTHER INFORMATION
SATIN STITCH FOOT
The Satin stitch foot is grooved to permit dense stitching to pass under it easily. It is most useful for sewing satin stitches and as an alternative to the General Purpose Foot when sewing Stretch Stitches.
Closely spaced zig-zag stitches are called satin stitches. This is an attractive stitch used primarily for appliqueing and bar tacking. Slightly loosen top thread tension for satin stitching. Use a backing of tissue paper or interfacing for the sheer materials to avoid puckering.
TWIN NEEDLE (Option)
A twin-needle produces two rows of parallel stitches for pin tucks, double top stitching and decorative sewing.
When using a twin-needles, the stitch width should never be set beyond a twin needle mark, regardless of the stitch you have selected. Doing so will result in broken needles and possible damage to your machine.
Use of a Singer Brand 3mm (Style 2025) Twin Needle is recommended. Twin needles are available in a range of sizes. Check with your Singer retailer.
THREADING THE TWIN NEEDLE
- Insert the second spool pin. Place a spool on each spool pin. Thread the two threads as one. Draw one thread through each needle from front to back.
- Pick up bobbin thread as for single needle sewing. Pull the three threads together under the presser foot to the back of the machine, leaving about 6” (15 cm) of thread.
NOTE: Needle threader cannot be used to thread the twin needle.
Helpful Hints
- Always move the stitch width to the Twin Needle Mark prior to selecting a pattern. This will preclude any possibility of the twin needle breaking.
- Turning off the machine returns the machine to normal sewing mode. Twin Needle is only active when the Twin Needle Switch is lit red.

STRAIGHT STITCH NEEDLE POSITION
The position of the needle when sewing straight stitch may be adjusted to 13 different positions with the stitch width control as illustrated

PERFORMANCE CHECKLIST
GENERAL PROBLEMS
Machine does not sew.
- Power switch is turned off.- Turn on the switch.
- Buttonhole lever is not raised when sewing stitch patterns.
- Raise buttonhole lever.
- Buttonhole lever is not lowered when sewing buttonhole.
- Lower buttonhole lever.
- Bobbin winder is engaged. – Disengage bobbin winder
Machine jams/knocks. - Thread is caught in hook.- Clean hook
- Needle is damaged.- Replace needle . Fabric does not move.
- Presser foot is not lowered – Lower presser foot.
- Stitch length is too short – Lengthen stitch length.
- Darning plate is placed on needle place – Remove darning plate.
STITCHING PROBLEMSMachine skips stitches.
- Needle is not all the way up into needle clamp.
- Needle is bent or blunt. – Replace needle
- Machine is not threaded correctly.
- Thread is caught in hook. – Clean hook . Stitches are irregular.
- Needle size is not correct for thread and fabric.
- Machine is not threaded correctly. –
- Top thread tension is too loose.
- Fabric is being pulled or pushed against machine feeding action. – Guide it gently.
- Bobbin has not been wound evenly. – Rewind bobbin. Needle breaks.
- Fabric is being pulled or pushed against machine feeding action. – Guide it gently.
- Needle size is not correct for thread and fabric.
- Needle is not all the way up into the needle clamp.
- Twin needle is being used but stitch width is set too wide
THREAD PROBLEMS
Thread bunches.
- Top and bobbin threads are not drawn back under presser foot before starting seam.
- Draw both threads back under presser foot about 6 inches (10 cm) and hold until a few stitches are formed.
Needle thread breaks.* Machine is not threaded correctly. - Top thread tension is too tight.
- Needle is bent. – Replace needle
- Needle size is not correct for thread and fabric
Bobbin thread breaks. - Bobbin case is not threaded correctly.
- Lint accumulates in bobbin case or hook.
- Remove lint Fabric puckers.
- Top thread tension is too tight. – Adjust thread tension
- Stitch length is too long for sheer or soft fabric. – Shorten stitch length.
Documents / Resources
![]() | 8763 Sewing Machine |
References
- User Manualmanual.tools


