Elgato Stream Deck Studio User Guide

Mounting

Use four screws per bracket. Six holes provide two mounting depths.

Screw four M4 screws (not included) directly into the enclosure.
Power Supply
There are two ways to power Stream Deck Studio:

- RJ45 Ethernet PoE+
Connect Stream Deck Studio via Ethernet to a PoE+ (802.3at Class 4) compatible network. The device will power on automatically. An on-key menu will display all network settings.
Press keys to select values, and use the left or right encoder to adjust settings. - USB-C PD 3.0
Connect a PD 3.0 compatible power supply (min. 9 V, 3 A, not included) to the USB-C POWER DELIVERY port. The device will power on automatically.
If Ethernet and USB-C are connected at the same time, Ethernet will be given priority and USB will be disabled.
Connection

USB-C (Back)
Connect your computer to the USB-C DATA CONNECTION port

USB Expansion Port (Front)
Connect a bus-powered Stream Deck device for additional control.

NFC Reader

Place your NFC token close to the icon to exchange data with Stream Deck Studio.
Software
Select your Bitfocus Buttons subscription plan.
Reset

To reboot the device, press and hold both encoders for 10 seconds.

To restore factory settings, press and hold the reset button while powering on the device.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and a human body.
For questions about Elgato product compliance with FCC regulations, please contact:
Compliance Officer, Corsair Memory Inc., 115 North McCarthy Blvd, Milpitas, CA 95035, USA
The declaration of conformity for Elgato products is available at www.elgato.com/doc
CORSAIR MEMORY, Inc. 115 North McCarthy Blvd, Milpitas, CA 95035, USA. CORSAIR MEMORY, BV. Wormerweg 8, 1311 XB, Almere, Netherlands. CORSAIR COMPONENTS, Ltd. 1020 Eskdale Road, Winnersh Triangle, Wokingham, RG41 5TS, UK. Copyright 2024 Corsair Memory Inc. All rights reserved. Elgato and the Elgato logo are trademarks of Corsair Memory Inc., registered in the U.S. and other countries. The X name and logo are trademarks of X Corp. in the United States and other countries. All other trademarks belong to their respective owner.
Customer Support: help.corsair.com
- Part: 51GBO9903

Co-designed by Legato and Bit focus
Symbols



Documents / Resources
![]() | Stream Deck Studio |
References
- Legacy routebitfocus.io
- Downloads | Elgatoelgato.com
- help.corsair.comhelp.corsair.com
- Declaration of Conformity | Elgatowww.elgato.com
- User Manualmanual.tools
