EPH ESP-01S Wifi Module

Specifications
- Module model: ESP-01S
- Encapsulation: DIP-8 package
- Spectrum range: 2400 – 2483.5 MHz
- Power supply range: 3.3V – 3.6V
- Number of IO ports: 12
- Serial port speed: Up to 4Mbps
FAQs
- Q: What is the standby power consumption of the ESP-01S module?
- A: The standby power consumption can be as low as 1.0mW.
- Q: What network modes are supported by the ESP-01S?
- A: The ESP-01S supports STA (Station), AP (Access Point), and ESTA+AP working modes.
- Q: What is the maximum serial port speed supported by the ESP-01S?
- A: The serial port speed can go up to 4Mbps.
Product Overview
- ESP-01S is a Wi-Fi module developed by Essence Technology. The module’s core processor
- ESP8266 integrates the industry-leading Tensilica L106 ultra-low power consumption 32-bit micro
- MCU in a smaller size package with 16-bit streamlined mode. The main frequency supports 80
- MHz and 160 MHz, supports RTOS and integrates Wi-Fi MAC/BB/RF/PA/LNA.
- ESP-01S Wi-Fi module supports standard IEEE802.11 b/g/n protocol and complete TCP/IP protocol stack. Users can use this module to add networking capabilities to existing devices or build independent network controllers.
- ESP8266 is a high-performance wireless SoC that provides maximum practicality at the lowest cost, providing unlimited possibilities for embedding Wi-Fi functionality into other systems.

ESP8266 has a complete and self-contained Wi-Fi network function, which can be used independently or as a slave to run on other host MCUs. When used independently, ESP8266 can be booted directly from the external flash. The built-in cache memory helps improve system performance and optimizes the storage system. In another case, ESP8266 can be used as a Wi-Fi adapter simply through the SPI/SDIO interface or UART interface and can be applied to any microcontroller-based design. The powerful on-chip processing and storage capabilities of ESP8266 enable it to integrate sensors and other application-specific devices through the GPIO port, greatly reducing the cost of early development.
Feature
- Complete 802.11b/g/n Wi-Fi SoC module
- Built-in Tensilica L106 ultra-low power consumption 32-bit micro MCU, main frequency supports 80 MHz and 160 MHz, supports RTOS
- Built-in 1 channel 10 bit high-precision ADC
- Support UART/GPIO/PWM interface
- Available in DIP-8 package
- Integrated Wi-Fi MAC/ BB/RF/PA/LNA
- Supports multiple sleep modes, with standby power consumption as low as 1.0mW
- Serial port speed up to 4Mbps
- Embedded Lwip protocol stack
- Support STA/AP/STA+AP working mode
- Supports Android and IOS Smart Config (APP)/AirKiss (WeChat) one-click network configuration
- Supports serial port local upgrade and remote firmware upgrade (FOTA)
- Common AT commands allow you to get started quickly
- Supports secondary development and integrates Windows and Linux development environments
The main parameters
| Module model | ESP-01S |
| Encapsulation | DIP-8 |
| Size | 24.4*14.4*11.2(±0.2)MM Note: 11.2mm is the height of the pin header Antenna from the Onboard PCB antenna |
| Spectrum range | 2400~2483.5MHz |
| Operating temperature | -20℃~70℃ |
| Storage environment | -40℃ ~ 125℃, < 90%RH |
| Power supply range | Power supply voltage 3.0V ~ 3.6V, power supply current >500mA Support interface UART/GPIO/PWM |
| Number of IO ports | 2 |
| Serial port speed | Support 110 ~ 4608000 bps, default 115200 bps security WEP/WPA-PSK/WPA2-PSK |
| SPI Flas | Default 8Mbit |
| Certification | RoHS |
Electrical parameters
Electrical characteristics
| Parameters | Conditions | Minimum | Typical | Maximum | Unit |
| Supply voltage | VDD | 3 | 3.3 | 3.6 | V |
| I/O | VIL/VIH | – | -0.3/0.75VIO | – | 0.25VIO/3.6 | V |
| VOL/VOH | – | N/0.8VIO | – | 0.1VIO/N | V | |
| IMAX | – | – | – | 12 | MA |
RF performance
| Describe Typical value Unit | ||
| Working frequency | 2400 – 2483.5 | MHz |
| Output Power | ||
| In 11n mode, the PA output power is | 13±2 | dBm |
| In 11g mode, the PA output power is | 14±2 | dBm |
| In 11b mode, the PA output power is | 16±2 | dBm |
| Receive sensitivity | ||
| CCK, 1 Mbps | <=-90 | dBm |
| CCK, 11 Mbps | <=-85 | dBm |
| 6 Mbps (1/2 BPSK) | <=-88 | dBm |
| 54 Mbps (3/4 64-QAM) | <=-70 | dBm |
| HT20 (MCS7) | <=-67 | dBm |
Power Consumption
The following power consumption data are based on a 3.3V supply, an ambient temperature of 25°C, and measured using the internal voltage regulator.
- All measurements are done at the antenna interface without SAW filter.
- All emission data are measured in continuous emission mode based on 90% duty cycle.
| Model Minimum Typical Maximum Unit | ||||
| Transmit 802.11b, CCK 11Mbps, POUT=+17dBm | 170 | – | mA | |
| Transmit 802.11g, OFDM 54Mbps, POUT =+15dBm | 140 | mA | ||
| Transmission 802.11n, MCS7, POUT =+13dBm | – | 120 | – | mA |
| Receive 802.11b, packet length 1024 bytes, -80dBm | – | 50 | — | mA |
| Receive 802.11g, packet length 1024 bytes, -70dBm | – | 56 | – | mA |
| Receive 802.11n, packet length 1024 bytes, -65dBm | – | 56 | — | mA |
| Modem-Sicep① | – | 20 | – | mA |
| Light-Sleep② | – | 2 | — | mA |
| Deep-Sleep③ | – | 20 | – | uA |
| Power Off | – | 0.5 | — | uA |
Illustrate
- Modem-sleep is used for applications that require the CPU to be working all the time, such as PWM or I2S applications. When maintaining a Wi-Fi connection, if there is no data transmission, the Wi-Fi Modem circuit can be turned off to save power according to the 802.11 standard (such as U-APSD). For example, in DTIM3, every 300 ms of sleep and 3 ms of wake-up to receive the AP’s Beacon packet, etc., the overall average current is about 20 mA.
- Light-sleep is used for applications where the CPU can be paused, such as Wi-Fi switches. When maintaining a Wi-Fi connection, if there is no data transmission, the Wi-Fi Modem circuit can be turned off and the CPU can be suspended to save power according to the 802.11 standard (such as U-APSD). For example, in DTIM3, every 300 ms of sleep and 3 ms of wake-up to receive the AP’s Beacon packet, etc., the overall average current is about 2 mA.
- Deep sleep is used for applications that do not need to maintain a Wi-Fi connection all the time and send data packets for a long time, such as a sensor that measures temperature every 100 seconds. For example, if it takes 0.3s ~ 1s to connect to the AP and send data after waking up every 300s, then the overall average current can be much less than 1 mA. The current value of 20 μA is measured at 2.5V.
Physical Dimension


Pin definition
The ESP-01S module has a total of 8 interfaces, as shown in the pin diagram and the pin function definition table is the interface definition.

| PIN | Name | Function Description |
| 1 | GND | Ground |
| 2 | 102 | GPI02/UARTl_TXD |
| 3 | 100 | GPI00: Download mode: externally pulled low; operating mode: floating or externally pulled high |
| 4 | RXD | UART0_RXD/GPI03 |
| 5 | TXD | UART0_TXD/GPI01 |
| 6 | EN | Chip enable terminal, active at a high level |
| 7 | RST | Reset |
| 8 | VCC | 3. 3V power supply (VDD); the output current of the external power supply is recommended to be above 500mA. |
Module startup mode description
| Model | CH_PD(EN) | RST | GPIO15 | GPIO0 | GPIO2 | TXD0 |
| Download mode | High | High | Low | Low | High | High |
| Operating mode | High | High | Low | High | High | High |
Note: Some pins have been pulled up internally, please refer to the schematic diagram
Schematic diagram

Design Guidance
- Application circuit
- Notice:
- For the module peripheral circuit, GPIO0 must be pulled up to VCC, and GPIO15 must be pulled down to GND.
- The EN pin and RST pin must be pulled up to VCC.
- Notice:
- Antenna layout requirements
- For the installation position on the motherboard, the following two methods are recommended:
- Solution 1: Place the module on the edge of the motherboard, and the antenna area extends beyond the edge of the motherboard.
- Option 2: Place the module on the edge of the motherboard, and hollow out an area at the edge of the motherboard where the antenna is located.
- To meet the performance of the onboard antenna, it is prohibited to place metal parts around the antenna and keep away from high-frequency devices.

- For the installation position on the motherboard, the following two methods are recommended:
- Power supply
- Recommended voltage of 3.3V, peak current of more than 500mA
- It is recommended to use LDO for power supply; if DC-DC is used, it is recommended that the ripple be controlled within 30mV.
- In the DC-DC power supply circuit, it is recommended to reserve the position of the dynamic response capacitor to optimize the output ripple when the load changes greatly.

- Use of GPIO port
- There are some GPIO ports on the periphery of the module. If you need to use it, it is recommended to connect a 10-100 ohm resistor in series to the IO port. This can suppress overshoot and make the levels on both sides more stable. Helps with both EMI and ESD.
- For the up-and-down pull-down of the special IO port, please refer to the instructions in the specification sheet, which will affect the startup configuration of the module.
- The IO port of the module is 3.3V. If the IO level of the main control and the module do not match, a level conversion circuit needs to be added.
- If the IO port is directly connected to the peripheral interface or pin header and other terminals, it is recommended to reserve ESD devices near the IO traces near the terminals.
- Level conversion circuit
- Reflow soldering curve
- Heating zone – Temperature: 25 ~ 150°C Time: 60 ~ 90s Heating slope: 1 ~ 3°C/s
- Preheating constant temperature zone – Temperature: 150 ~ 200°C Ttime: 60 ~ 120s
- Reflow soldering area – Temperature: >217°C Time: 60 – 90s; Peak temperature: 235 ~ 2500c Time: 30 – 70s
- Cooling zone — Temperature: Peak temperature ~ 180°C Cooling slope -1 – -5°C/s
- Solder – Tin Silver Copper Allov Lead-Free Solder (SAC305)
Documents / Resources
![]() | ESP-01S Wifi Module |
References
- User Manualmanual.tools
