GYS DS6600 Smart Printer Module

INSTRUCTION MANUAL
SMART PRINTER MODULE
FIG-1

FIG-2

SAFETY INSTRUCTIONS

This manual contains safety and operating instructions, to be followed for your safety. Please read it carefully before using the device for the first time and keep it for future reference. Read and understand the following safety instructions before use. Any modification or update that is not specified in the instructions manual should not be undertaken. The manufacturer is not liable for any injury or damage due to non-compliance with the instructions featured in this manual. If there is any issue or uncertainty, please consult a qualified individual to operate the equipment correctly. This device may only be used for ticket printing and/or data transmission within the limits indicated on the device and manual. The operator must follow the safety instructions. In case of improper or unsafe use, the manufacturer cannot be held liable.

- Do not use the charger if the mains cable or plug is damaged.
- Do not place the unit near a heat source/direct sunlight and durably high temperatures (above 50 ° C)
- This machine must be connected to an earthed socket.
Maintenance :

- Maintenance should only be carried out by a qualified person.
- Warning ! Always disconnect from the mains before performing maintenance on the device.
- Do not use solvents or other aggressive cleaning products under any circumstances
- Clean the surfaces of the unit with a dry cloth.
Regulations :
- The Machine is compliant with European directives.
- The declaration of conformity is available on our website.
![]()
- Equipment in compliance with British requirements. The Brit-ish Declaration of Conformity is available on our website (see home page).
![]()
- Equipment in conformity with Moroccan standards.
![]()
- The declaration Cم (CMIM) of conformity is available on our website (see cover page).
Waste management:
![]()
This product should be disposed of at an appropriate recycling facility. Do not throw away in a household bin..
It is recommended to use the cables supplied with the unit in order to obtain the optimal product settings.
EQUIPMENT DESCRIPTION (FIG-1)
The Smart Printer Module (SPM) is an accessory that allows GYS «Connected» products (chargers, welding stations, etc.) to print reports on tickets. It also has 2 USB ports for a barcode reader (ref. 027718) and a keyboard (ref. 027725 / ref. 027770).
1- Printer roll cover
2- Paper compartment opening lever
3- Paper feed button
4- Power LEDs
5- Warning LED
6- USB ports
7- Mains input
8- SMC connector
9- IEC C13 mains power cord
10- SMC connection cable
CONSUMABLE AND OPTIONS

INSTALLATION AND CONNECTION TO THE HOST PRODUCT
- Connect the SPM to the host product using the SMC connection cable.
- To benefit from increased performance (high print speed, higher contrast, and high current available on the USB ports), connect the SPM to the electrical installation using the IEC C13 cable supplied.
If necessary, connect the keyboard and barcode reader to the USB port. Attention, the use of accessories other than those offered by GYS is not covered by the warranty. The simultaneous use of two barcode readers is also not covered by the warranty. - Configure the language of the barcode reader (see below) as well as the keyboard type on the host product (Azerty, Qwerty, Qwertz, etc.).

POWER SWITCH
- This equipment can function with or without being connected to the mains. However, it must be connected to the host product using the SMC connector. Printing performance is improved when the product is powered by the mains.
- This product can be connected to a single-phase 3pin power supply 100V -240V (50-60Hz) with earth connnection.
- When the SPM is turned on by the host product, the indicator light flashes quickly for a few moments (initialisation phase).
CONNECTION TO A GENERATOR
The machine can work with generators as long as the auxiliary power matches these requirements :
– The voltage must be AC, always set as specified, and the peak voltage below 400V,
– The frequency must be between 50 and 60 Hz.
It is imperative to check these values as many generators generate voltage spikes that can damage the machine.
INSTALLATION OF PAPER ROLL (CONSUMABLE REF. 056237)
To change the paper roll, open the printer cover with the lever (FIG 1 – 2). Position a new roll by pulling the 10 mm paper out of the cover.
INTERFACE (MMI) (FIG-2)

ANOMALIES, CAUSES AND REMEDIES

CONFIGURATION OF THE BARCODE READER (ACCESSORY REF. 027718)
To work properly with the SPM, the barcode reader must be set to the default mode (USB, 9600b/s baud rate). If in doubt, flash this barcode to reset it.

For a customised configuration of the barcode reader (alarm, volume, lowercase and uppercase characters, uppercase, etc.), refer to the online barcode reader manual on the GYS website (ref. 027718).

Flasher this barcode to configure the AZERTY barcode reader.

Flasher this barcode to configure the QWERTY barcode reader.

Flasher this barcode to configure the QWERTZ barcode reader.
WARRANTY
The warranty covers faulty workmanship for 2 years from the date of purchase (parts and labour).
The warranty does not cover:
- Transit damage.
- Normal wear of parts (eg. : cables, clamps, etc..).
- Damages due to misuse (power supply error, dropping of equipment, disassembling).
- Environment related failures (pollution, rust, dust).
In case of failure, return the unit to your distributor together with:
– The proof of purchase (receipt etc …)
– A description of the fault reported
SPARE PARTS

1. Printer
2. Electronic board
3. Mains terminal block
4. DB9 ribbon connector
5. Protection pads (x4)
6. Magnet
7. Protection magnet
8. SMC connection cable
9. IEC C13 mains power cord
CIRCUIT DIAGRAM

TECHNICAL SPECIFICATIONS
- Part number: 026919
- Power supply voltage: 100-240 VAC
- Mains frequency: 50 / 60 Hz
- Max input current: 140-90 mA
- Operating temperature: 0°C > +40°C
- Storage temperature: -10°C > +50°C
- Level of protection: IP21
- Protection class: Class I
- Noise level: < 50dB
- Resolution: 200 dpi
- Printing speed: 80 mm/s max.
- Paper width: 57 mm
- Dimensions (LxWxH): 140 x 105 x 133 mm
- Weight: 1.35 kg
- Standards: EN 60335-1, EN 62233 (EMF), CEI EN 60529 (IP), EN 50581 (RoHS), EN 55014-1 (CEM), EN 55014-2 (CEM), CEI 61000-3-2, CEI 61000-3-3
Specifications:
- Input: 100-240 V~50/60 Hz 10 A max
- Connection: SMC
- Consumables: Paper roll x2 57 mm, Mini USB keyboard, 1D/2D barcode reader
- Options: Trolley GYSFLASH XL, SMC connection cable 3m
Frequently Asked Questions (FAQ)
Q: What type of paper rolls does the product use?
A: The product uses paper roll x2 size 57 mm.
Q: How do I connect the machine to a generator?
A: Make sure the generator’s voltage is within the specified range and the frequency is between 50 and 60 Hz. Connect the machine following the provided guidelines to prevent damage.
Q: What should I do if the indicator light is flashing slowly?
A: If the indicator light is flashing slowly, ensure that the power supply is provided by the host product only.
Documents / Resources
![]() | DS6600 Smart Printer Module |
References
- Arc Welding, Battery Chargers & Body Repair | GYSwww.gys.fr
- User Manualmanual.tools
