JBL Flip 6 Portable Waterproof Speaker
What’s In the Box
Bluetooth Pairing
Play
Party Boost
App
Charging
WaterProof
TECH SPEC
- Transducers:45 x 80 mm woofer / 1.75 x 3”, 16 mm tweeter / 0.6”
- Output power:20 W RMS for the woofer, 10 W RMS for the tweeter
- Frequency response:63 Hz – 20 kHz
- Signal-to-noise ratio:> 80 dB
- Battery type:Li-ion polymer 17.28 Wh (equivalent to 3.6 V / 4800 mAh)
- Battery charge time:2.5 hours (5 / 3 A)
- Music play time:up to 12 hours (dependent on volume level and audio content)
- Cable type:USB – C charging cable
- Cable length:1.2 m / 47.2”
- Bluetooth® version:5.1
- Bluetooth® profile:A2DP 1.3, AVRCP 1.6
- Bluetooth® transmitter frequency range:2400 MHz – 2483.5 MHz
- Bluetooth® transmitter power:≤ 10 dBm (EIRP)
- Bluetooth® transmitter modulation: GFSK, π/4 DQPSK, 8DPSK
- 2.4GHz SRD frequency range:2407 MHz – 2475 MHz
- SRD transmitter power:< 10 dBm (EIRP)
- Product dimensions (W x H x D):178 x 68 x 72 mm / 7.0 x 2.6 x 2.8”
- Net weight:0.55 kg / 1.21 lbs
- Packaging dimensions (W x H x D):216 x 106 x 99 mm / 8.5 x 4.2 x 3.9”
- Gross weight:0.92 kg / 2.0
CAUTION
To protect battery lifespan, fully charge at least once every 3 months. Battery life will vary due to usage patterns and environmental conditions.
Do not expose the JBL Flip 6 to liquids without removing cable connection. Do not expose JBL Flip 6 to water while charging. It may result in permanent damage to the speaker or power source.
Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the connector surface over time if not rinsed off after use. After a liquid spill or rinsed, do not charge your speaker until it’s completely dry and clean. Charging when wet might damage your speaker.
With USB-C charging protection, a reminder sound will alert you to unplug if the connector detects water, salt, or any other chemicals.
When using an external adapter, the output voltage/current of the external adapter should not exceed 5V/3A.
SPECIFICATION
| Product Specifications | Details |
|---|---|
| Brand | JBL |
| Model | Flip 6 Portable Waterproof Speaker |
| What’s In the Box | – JBL Flip 6 Portable Waterproof Speaker – USB-C charging cable – Quick start guide – Warranty card – Safety sheet |
| Bluetooth Pairing | Automatically pairs with Bluetooth-enabled devices |
| Play | Play music from your device by selecting it as an input source in your music player app or by using one of our pre-programmed playlists in Party Boost mode |
| Party Boost | Connect multiple JBL PartyBoost-compatible speakers to create a bigger party |
| App | JBL Portable app for additional features and customization |
| Charging | Charged through a USB connection in about 2.5 hours (5 V / 3 A) |
| WaterProof | IP67 rating protects the product from submersion in 1 meter (3.3 feet) of water for up to 30 minutes and it is also Dust-proof |
| Transducers | 45 x 80 mm woofer / 1.75 x 3”, 16 mm tweeter / 0.6” |
| Output power | 20 W RMS for woofer, 10 W RMS for tweeter |
| Frequency response | 63 Hz – 20 kHz |
| Signal-to-noise ratio | > 80 dB |
| Battery type | Li-ion polymer 17.28 Wh (equivalent to 3.6 V / 4800 mAh) |
| Battery charge time | 2.5 hours (5 V / 3 A) |
| Music play time | Up to 12 hours (dependent on volume level and audio content) |
| Cable type | USB-C charging cable |
| Cable length | 1.2 m / 47.2” |
| Bluetooth® version | 5.1 |
| Bluetooth® profile | A2DP 1.3, AVRCP 1.6 |
| Bluetooth® transmitter frequency range | 2400 MHz – 2483.5 MHz |
| Bluetooth® transmitter power | ≤ 10 dBm (EIRP) |
| Bluetooth® transmitter modulation | GFSK, π/4 DQPSK, 8DPSK |
| 2.4GHz SRD frequency range | 2407 MHz – 2475 MHz |
| SRD transmitter power | < 10 dBm (EIRP) |
| Product dimensions (W x H x D) | 178 x 68 x 72 mm / 7.0 x 2.6 x 2.8” |
| Net weight | 0.55 kg / 1.21 lbs |
| Packaging dimensions (W x H x D) | 216 x 106 x 99 mm / 8.5 x 4.2 x 3.9” |
| Gross weight | 0.92 kg / 2.0 |
| CAUTION | To protect battery lifespan, fully charge at least once every 3 months. Battery life will vary due to usage patterns and environmental conditions. Do not expose the JBL Flip 6 to liquids without removing cable connection. Do not expose JBL Flip 6 to water while charging. It may result in permanent damage to the speaker or power source. Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the connector surface over time if not rinsed off after use. After a liquid spill or rinsed, do not charge your speaker until it’s completely dry and clean. Charging when wet might damage your speaker. With USB-C charging protection, a reminder sound will alert you to unplug if the connector detects water, salt, or any other chemicals. When using an external adapter, the output voltage/current of the external adapter should not exceed 5V/3A. |
| FAQs | – Can I use the JBL Flip 6 with my car stereo? – How do I connect the JBL Flip 6 to my phone? – How do I charge the JBL Flip 6? – How long does it take to charge the battery? – How do I play music from my phone or tablet? – Can I use my speaker when it is charging? – Can the Flip 6 remain plugged in all the time or will that damage the battery over time? – How many watts is jbl flip 6? – How can I tell that my JBL Flip 6 is charging? How can I tell when it is fully charged? How can I tell how much battery life is left after use? – What is the difference between flip6 and flip5? – Can use a thumb drive play music? – Can it be set up so if I walk away with my phone it will still play? |
FAQs
Yes, you can! You can connect the JBL Flip 6 to your car stereo via Bluetooth® or the 3.5 mm aux-in jack.
The JBL Flip 6 pairs with your phone automatically when you turn it on. If this does not happen, go to “Settings” and select “Bluetooth®” on your phone. Then select “JBL Flip 6” from the list of available devices.
Connect the USB charging cable to a power source and plug it into the micro-USB port on the back of the speaker. The battery is charged through this port.
The battery is charged through a USB connection in about 2.5 hours (5 V / 3 A).
First, pair your device with your speaker by following these steps: 1) Turn on Bluetooth® on your device and make sure that Bluetooth® is enabled and that it is set to “On”. 2) Press and hold down the power button for 3 seconds until you see “Pairing” on the LED display. 3) On your device, search for available Bluetooth® devices and select “JBL Flip 6” from the list of available devices. 4) If a PIN code appears on your device, enter “0000” (four zeros). 5) Once connected, you can play music from your device by selecting it as an input source in your music player app or by using one of our pre-programmed playlists in Party Boost™ mode (see page 8 for more details).
Yes, but please note that charging reduces battery life and therefore limits how long you can play music before recharging. Also note that if you use Party Boost™ mode while charging, you will hear sound from only one of your speakers at a time as they alternate playing music in Party Boost™ mode (see page 8 for more details). To avoid this issue, we recommend that you turn off Party Boost™ mode when charging.
There is no harm in leaving your JBL Flip 6 connected to electricity at all times. You can simply pick it up, unplug it from the charger and be on your way, knowing that you have a full charge. The battery will not overcharge. However, if you’d like to conserve electrical energy, disconnect from charging.
Our JBL Flip 6 has 30 watts RMS.
Our JBL Flip 6 has a battery light indicator next to the Bluetooth button which tells you how much charge your speaker has left.
Here is the difference between our JBL Flip 5 and Flip 6:
Our JBL Flip 6 – Portable Bluetooth Speaker does not have an Aux Input, so no analog connection is possible.
Thanks for your question. Our JBL Flip 6 is manufactured in China.
Our JBL Flip 6 has an IP67 rating. IP67 protects the product from submersion in 1 meter (3.3 feet) of water for up to 30 minutes and it is also Dust-proof.
Thanks for your question. The Flip 6 has no provision to connect a thumb drive.
World Wide Stereo is 43 years old and a proud authorized JBL dealer.
Yes, you can walk away with your phone and it will still play, as long as you don’t walk to far. This speaker is like any other blue tooth device that has a certain range.
What is included in the box with the JBL Flip 6 Portable Waterproof Speaker?
The box includes the JBL Flip 6 speaker and a USB-C charging cable.
How do I pair the JBL Flip 6 with my Bluetooth-enabled device?
Turn on Bluetooth on your device and select “JBL Flip 6” from the list of available devices.
How do I use Party Boost on the JBL Flip 6?
Press the Party Boost button on your JBL Flip 6 and connect it to other Party Boost-compatible speakers to amplify your music.
Video
Documents / Resources
References
- User Manualmanual.tools