Ankilo 3618LP Projection Alarm Clock

Product Specifications:
- 4-bit LED display
- Time function: displays hour and minute in 12/24 hour system
- Date function: displays day, month, and year (2000 to 2099)
- Alarm function: set daily alarm and snooze Temperature function: displays temperature (-10~50°C / 14~122°F)
- Mode selection: change modes in temperature mode
- Brightness control: adjust screen brightness (high-middle-low-off)
- Low light: automatic low light function from 18:00-5:59
- LCD projection function: turn on/off projection
- External power supply: 5V/DC with built-in lithium battery (3.0V)
- All keys have sound
Time Mode
After connecting the power, the LED screen will display for 2 seconds then enter the normal time mode. Default is 0:00 in 24-hour system. Press MODE key to cycle through Time mode, Date mode,
Temperature mode, Night on/off. Long press MODE key for 2 seconds to set the time. Use UP/DOWN keys to adjust hours and minutes. Hour range: 1-12 or 0-23, Minute range: 00-59.
Date Mode
In normal time mode, press MODE key to enter Date mode. Long press MODE key for 2 seconds to set the date. Use UP/DOWN keys to adjust year, month, and date. Year range: 2000-2099, Month range: 1-12, Date range: 1-31.
3618LP Instructions
Functions
- 4-bit LED display
- Time function: it displays hour ,minute and it can change in 12/24 hour system.
- Date function: it displays day, month and year (from 2000 to 2099).
- Alarm function: you can set daily alarm and snooze.
- Temperature function: It can display and change the ℉/℃. The normal measurement range is -10℃~ 50℃ (14℉~122℉).
- Mode selection: in the temperature mode long press MODE key to change modes.
- Brightness control: you can press SNOOZE key to adjust the screen brightness from high-middle-low-off.
- Low light: when 18:00-5:59,the screen is in low light automatically and you can set automatic low light interval.
- The LCD projection function. You can press PROJECT key to turn on/off the projection.
- The external power supply 5V/DC is the typical working voltage,and the protection for external power-cut.(built-in lithium battery:3.0V)
- All keys have sound.
LED and LCD screen display& Key function description

Key format:there are 6 keys(5 keys of LED clock and 1 key of projection clock).

Detailed Operations
- Time mode:
- After connecting the power, the LED screen will full display for 2s then it makes a sound “Bi” to enter the normal time mode and the default is 0:00 in 24 hour system.
- In the normal time mode, press MODE key to enter the corresponding functions as follows:
Time mode–Date mode–Temperature mode–Night on/off (the default is off) - In the normal time mode,long press MODE key for 2s to enter time mode, and press UP/DOWN key to set time as follows. Press and hold to quickly increase/decrease. 12/24 hour system– Hour– Minute– Escape
- If you change to the 12 hour system , the sign PM will light.
- Setting range: HOUR is 1~12 or 0~23, MIN is 00~59.
- Set hour, the second won’t change; Set minute, the second will reset.
- In the setting mode, it will escape the setting mode without any key for 10s later and keep the time you set before.
- Date mode:
In the normal time mode, press MODE key to enter the date mode, the date displays 1st, January, 2018.- In the date mode, long press MODE key for 2s to set date, and press UP/DOWN key to set time as follows. Press and hold to quickly increase/decrease. Year– Month– Date– Escape
- Setting range: MONTH is 1~12 , DAY is 1~31, YEAR is 2000~2099.
- In the setting mode, it will escape the setting mode without any key, then return to the time mode.
- Alarm mode:
- In any mode, press ALM key to display the alarm mode, alarm time displays 6:00 in 24 hour system.
- In the alarm mode, press ALM key to turn on/off alarm.
- In any mode, long press ALM key for 3s to set alarm, and press UP/DOWN key to set time as follows.
Press and hold to quickly increase/decrease.
Hour– Minute– Snooze time–Choose alarm(1-7/1-6/1-5)–Escape - The set range is: hour is 1~12 or 0~23, minute is 00~59; the snooze interval is 1-60 minutes and the default is 5 minutes; the default alarm is 1-7 daily alarm.
- In the setting mode, it will escape the setting mode by press ALM key /without any key for 10s , and then it will return to the time mode.
- When the alarm reaches the point, it will automatically return to the alarm mode, with a “didididi” alarm sound, from slow to faster, and the alarm sign flashes at the same time, you can press any key to stop the alarm. Or there is no key operation and the alarm stops for 1 minute, but the alarm sign will not disappear.
- When the alarm rings, press the SNOOZE key to stop ringings and turn on one snooze, the alarm sign will flash; press other keys (except SNOOZE key) can stop ringing but no snooze.
- During the snooze interval, press other keys to turn off the snooze; pressing the SNOOZE key does not affect the snooze.
- When the alarm stops ringing, the alarm state is displayed, and it returns to the time state after 10s.
- In the alarm setting mode,it will stop ringing.
- Temperature mode
- After connecting the power, the clock will automatically detect the temperature, press MODE key to enter the the temperature mode. The normal measurement range is -10℃~50℃(14℉~122℉).
- When the temperature below -10℃,the screen displays -10℃;When the temperature above 50℃,the screen displays 50℃; When it has no resistance, the screen displays -10℃.
- The clock will detect the temperature every 10s, in the temperature mode press DOWN key to switch ℃/℉.
- In the temperature mode, press and hold the MODE key until there is a BI beep, and switch to LED to display the time, date and temperature in turn, the time is displayed for 10s, and the date and temperature are displayed for 3s; then press and hold the MODE key again until there is a BI beep and display the normal time.
- Night mode
- In the normal time/date/temperature mode, press SNOOZE key to set brightness, High –middle–Low–Off three modes.
- In the time mode, press MODE key 3 times to enter the night setting mode, press UP or DOWN to turn on (ON)/off (OFF) night mode (the default is off (OFF) night mode).
- When the night mode turns on, during 18:00-5:59 the screen is in low light automatically.
- In the night mode, if the brightness is not adjusted, after exiting it will display the brightness you set before.
- When the night mode is ON, press and hold the MODE key for about 2s to enter the night mode time setting. The setting sequence is: start hour → start minute → end hour → end minute.
- Projection function
- The projection adopts LCD display, and only the time is displayed at any time without turning off the screen. Even if the main screen LED goes off, the LCD projection does not need to be turned off. Even if the main LED screen is off, pressing LIGHT key can also turn on the projection to check the time.
- No matter what mode the LED main screen displays, the projection only displays the time.
- When setting the time mode, the LCD can display synchronously with the main screen LED, but when setting other modes, the LCD screen only stays in the time mode.
- Press LIGHT key at any time to turn on the projection (two brightness:high light and low) to check the time.
Documents / Resources
![]() | 3618LP Projection Alarm Clock |
References
- User Manualmanual.tools


I have to have the clock facing backward behind my bed up in a window to project on the ceiling the correct way. (It shows the time on the face of the clock to my neighbor). I can’t figure how to set it so I can see the time on my clock when I’m not in bed, and still project correctly on the ceiling.
Thank you for your help!
Thank you for your help!
How can I rotate the projection on the Ankilo 3618LP so the clock face and projection are both readable from the same direction?
Based on the Ankilo 3618LP manual, the projection unit is designed to be adjustable, but the specific method for flipping or rotating the image is limited. Here are the steps to optimize your setup:
If the image remains mirrored or upside down despite these steps, the manual does not specify a dedicated digital 'flip' button for this specific 3618LP model, and you may need to adjust the physical tilt of the projection arm to its opposite limit.
Read the full Q&A page
Pourquoi si il y a une batterie a l’intérieur il ne fonctionne pas sans être brancher
Why does the alarm clock not work without being plugged in, even though there is a battery inside?
The built-in 3.0V lithium battery in the Ankilo 3618LP is designed for memory backup only. It ensures that your time and alarm settings are saved in the event of a power outage so you do not have to reset them.
According to the manual, the typical working voltage is 5V/DC via an external power supply. The LED display and projection functions require more power than the small button battery can provide, so the clock must remain plugged into a USB power source or wall outlet to function and display the time.
Read the full Q&A page
Không lưu lại cài đặt được
How do I save settings on the Ankilo 3618LP Projection Alarm Clock?
To ensure your settings are saved on the Ankilo 3618LP Projection Alarm Clock, please follow these steps based on the manual:
Read the full Q&A page
Come cambiare il senso del proiettore led?
How do I change the orientation or direction of the LED projector?
To change the orientation of the projected time on the Ankilo 3618LP, you can use the PROJECT button (also referred to as the LIGHT key in some sections of the manual). While the manual primarily mentions using this key to turn the projection on/off and adjust brightness (High or Low), most projection clocks of this design allow you to flip the image by pressing or long-pressing the projection button.
According to the manual:
If the image is upside down, try a short press or a long press (3 seconds) of the PROJECT button to rotate the display 180 degrees. Additionally, the projection arm itself can be physically tilted to change the direction of the projection on your wall or ceiling.
Read the full Q&A page
How do I set the day of the week
How do I set the day of the week on the Ankilo 3618LP?
The Ankilo 3618LP Projection Alarm Clock does not have a standalone "day of the week" setting. Instead, the day of the week is automatically calculated by the device based on the Year, Month, and Date you program into the Date mode.
To set the date so the correct day of the week is displayed:
Additionally, when setting your alarm, you can choose which days the alarm should sound by selecting the working day mode: 1-7 (Monday-Sunday), 1-6 (Monday-Saturday), or 1-5 (Monday-Friday).
Read the full Q&A page