8BitDo Arcade Game Controller Instruction Manual

8BitDo Arcade Game Controller Instruction

Specifications

Arcade Controller Pro

1. Mode switch
2. Tournament lock switch
3. Display
4. Ultimate button
5. Pair button
6. Status LED
7. Home button
8. Square button
9. L3 button
10. R3 button
11. SELECT
12. Start
13. Adapter compartment switch
14. USB-C
15. 2.4G adapter / Adapter compartment
16. USB-C

Display

• Press the Ultimate button to enter or exit the Built-in Ultimate Software. Game input will be disabled while operating the Built-in Ultimate Software.
• The Built-in Ultimate Software cannot be operated when the Tournament lock switch is enabled.

Main Screen

• The default main screen displays status information.

Menu

• Button mapping, SOCD mode, lighting, display, language, and other settings can be configured in the Built-in Ultimate Software.
• Use the D-pad to navigate, press B button to go back, and A button to select.

A Button Mapping

• Edit Button Mapping.

B SOCD Mode

Change SOCD Mode (Default: SOCD Mode 1 – Neutral):

1. SOCD Mode 1: Neutral
2. SOCD Mode 2: Absolut Up Priority
3. SOCD Mode 3: First Input Priority
4. SOCD Mode 4: Last Input Priority

C Lighting

Lighting Mode, Color & Speed. Lighting Mode:

1. Echo Press
2. Breathing
3. Fixed
4. Flow
5. Ripple
6. Off

D Display

E Language

F Display off

• • Adjust display brightness.
  • Supports multiple languages.
  • Manually turn off the display (press the Ultimate button to turn it back on).

Windows

• System requirement: Windows 10 (1903) or above.

Wireless Connection

1. Turn the Mode switch to the X position.
2. Connect the adapter to the USB port of your Windows device.
3. After the connection is complete, the Status LEDs on both the Arcade Controller Pro and the adapter will remain solid.

Wired Connection

1. Turn the Mode switch to the X position.
2. Connect the Arcade Controller Pro to your Windows device via the USB cable, and wait until the Arcade Controller Pro is successfully recognized by the Windows device.

Switch

• System requirement: 3.0.0 or above.

Bluetooth Connection

1. Turn the Mode switch to the S position.
2. Press and hold the Pair button for 3 seconds to enter the pairing mode; the Status LED will blink rapidly. (This is required for the very first time only)
3. Go to your Switch Home Page to click on “Controllers”, then click on “Change Grip/Order”. The Status LED will remain solid to indicate a successful connection.

Wired Connection

• Switch 1: Enable “System Settings Controllers and Sensors -i Pro Controller Wired Communication”.
• Switch 2: Enable “System Settings Controllers and Accessories Pro Controller Wired Communication”.

1. Turn the Mode switch to the S position.
2. Connect the Arcade Controller Pro to your Switch console via the USB cable, and wait till the Arcade Controller Pro is successfully recognized by the device.

Tournament Lock Switch

• Turn the Tournament Lock switch to the Lock position. The Pair button, Ultimate button, Home button, L3 button, R3 button, Square button, SOCD mode(neutral by
  default), and Built-in Ultimate Software will be disabled to prevent unintentional inputs from impacting the game.

Battery

• Built-in 3000mAh battery pack, 15 hours of usage time via Bluetooth connection and 15 hours of usage time via wireless 2.4G connection, rechargeable with 4 hours charging time.
• The Arcade Controller Pro will automatically shut down if it fails to connect within 1 minute of startup, or if there are no operations within 15 minutes after establishing a connection.
• The Arcade Controller Pro will not shut down during a wired connection.
• Charging time and battery life depend on variations in settings or environmental factors, and actual results may vary.

Re-pair the Adapter

If the Arcade Controller Pro is disconnected from the adapter or the adapter is replaced, you can re-pair it by following these steps:

1. Turn the Mode switch to the X position.
2. Turn the Tournament lock switch to the Unlock position.
3. Press and hold the Pair button for 3 seconds to enter the pairing mode; the Status LED will blink rapidly.
4. Connect the adapter to the USB port of your Windows device, and wait for the Arcade Controller Pro to automatically pair and connect with the adapter.
5. After the connection is complete, the Status LEDs on both the Arcade Controller Pro and the adapter will remain solid.

Safety Warnings

• Please always use batteries, chargers, and accessories provided by the manufacturer.
• The manufacturer is not liable for any safety issues arising from the use of non-manufacturer-approved accessories.
• Do not attempt to disassemble, modify, or repair the device yourself. Unauthorized actions may result in serious injury.
• Avoid crushing, disassembling, puncturing, or attempting to modify the device or its battery, as these actions can be dangerous.
• Any unauthorized changes or modifications to the device will void the manufacturer’s warranty.
• This product contains small parts that may cause choking. Not suitable for children under three years old.
• This product features flashing lights. Individuals with epilepsy or photosensitivity should disable the lighting effects before use.
• Cables may cause tripping or entanglement hazards. Keep them away from walkways, children, and pets.
• Stop using this product immediately and seek medical attention if you experience dizziness, visual disturbances, or muscle spasms.

Ultimate Software

• Please visit [app.8bitdo.com](http://app.8bitdo.com/) to download and use Ultimate Software V2 for Windows / macOS platforms.

Support

• Please visit [support.8bitdo.com](http://support.8bitdo.com/) for further information & additional support.

Troubleshooting

• Controller shuts down shortly after startup: If it fails to connect within 1 minute of startup, it will automatically shut down.
• Controller turns off after connecting: If there are no operations within 15 minutes after establishing a connection, it will shut down.
• Will not shut down while wired: The device will not shut down during a wired connection.
• Need to re-pair after disconnection or adapter replacement: (1) Set the switch to X. (2) Turn it to Unlock. (3) Press and hold Pair for 3 seconds (Status LED blinks rapidly). (4) Connect the adapter to the USB port on the Windows device and wait for automatic pairing and connection. (5) Confirm both Status LEDs remain solid.
• Unintentional inputs during locked state: When the switch is moved to the Lock position, the Pair, Ultimate, Home, L3, R3, and Square buttons (and SOCD mode set to Neutral by default) are disabled to prevent unintentional inputs from impacting gameplay.