360 logo6970312875631 360 Video Doorbell X3
User Guide

6970312875631 360 Video Doorbell X3

What’s Included

6970312875631 360 Video Doorbell X3 - included

Getting to Know the Product

360 Video Doorbell X3 (Doorbell)

6970312875631 360 Video Doorbell X3 - video

Doorbell Power on/ Power off Press and hold the power button for 3 seconds
Add Doorbell to Wi-Fi You will hear “WiFi Connection Success” when you added your doorbell to a Wi-Fi
Reset the doorbell Press and hold the power button for 15 seconds

360 Video Doorbell X3 (Base Station)

6970312875631 360 Video Doorbell X3 - base stationNote: Power plug may vary in different regions

What’s Required for Installation

6970312875631 360 Video Doorbell X3 - installation

How the System Works

The video doorbell system consists of 2 parts. One is the Video Doorbell at your door. The other is the Base Station in your house.
The Video Doorbell detects motion at your porch and allows you to answer the door anytime and anywhere. The Base Station stores video clips on its built-in storage. When someone rings the doorbell, people in the house will be notified.

6970312875631 360 Video Doorbell X3 - syastem work

Botslab App Installation and Setup

Download the Botslab app on App Store or Google Play and install the app on your device.

6970312875631 360 Video Doorbell X3 - set up

  1. Register or log in to the app.
  2. Click ‘+’ at the top right corner of the screen, and select 360 Video Doorbell X 3 from the list, then follow the instructions in the app to set up the network.

How to Install

Option 1 – Battery Powered

  1. If you don’t have existing doorbell wiring at the front door, you can use the built-in battery to power the video doorbell. Position the doorbell wherever you like, and the mounting is easy and quick.
  2. When the doorbell battery level is low, you need to detach and charge it.

6970312875631 360 Video Doorbell X3 - battery power

Note: The battery life varies depending on usage. In most common cases, a doorbell may have up to 10 events per day and each recording lasts 20 seconds on average. Under this scenario, the doorbell battery life can last up to 6 months.

Step 1 Find a Mounting Spot

  1. Take the Video Doorbell to your front door and check the live view on the app at the same time. Find a location where you can get the desired field of view. Consider the factors below:
    1. Check if you can reuse the existing holes and anchors on the wall or door frame.
    2 If you want to place the doorbell close to a side wall, make sure the wall doesn’t show up in the field of view. Otherwise, IR light may be reflected and night vision can become blurry.
    6970312875631 360 Video Doorbell X3 - mounting spot 13. If you are drilling the mounting holes for the first time, the recommended mounting height is 48″ / 1.2 m from the ground. (Figure 8)
    4. Use the 15° mounting wedge as a supplementary mounting bracket if you wish to see more on a specific side. (Figure 9)
    6970312875631 360 Video Doorbell X3 - mounting spot 2
  2. Place the Screw Hole Positioning Card against the wall to mark the position. (Figure 10)
    6970312875631 360 Video Doorbell X3 - mounting spot 3

Step 2-1 Mounting the Bracket Mount the Doorbell on a Wooden Surface

If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall, The Screw Hole Positioning Card gives the position of the screw holes.

6970312875631 360 Video Doorbell X3 - mounting the bracket

What is required:

6970312875631 360 Video Doorbell X3 - required

Step 2-2 Mount the Doorbell on a Smooth Surface

If you’re mounting the doorbell on a smooth surface.

  1. Peel off the red foil that has the 3M VHB texts on it, and attach the backplate to where you want to sit your doorbell.
  2. Press hard on the backplate for 5 seconds.
  3. Let it be there and dwell for at least 24 hours so the 3M VHB tape can sink into the surface and build the strongest bond.
    6970312875631 360 Video Doorbell X3 - smooth surface

What is required:

6970312875631 360 Video Doorbell X3 - syastem work 1

Step 2-3 Mount the Doorbell on a Surface Made Out of Hard Materials

If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, or stucco:

  1. Drill 4 holes through the Screw Hole Positioning Card with a 15/64″(6mm) drill bit.
  2. Insert the provided anchors, and then use the provided long screws to secure the Mounting Bracket on the wall.

6970312875631 360 Video Doorbell X3 - hard materials

6970312875631 360 Video Doorbell X3 - requried

What is required:

6970312875631 360 Video Doorbell X3 - requried 1

Step 3 Mount the Doorbell

Align the doorbell on top and then snap it on the bottom. Press it down until it clicks into place.
You’re all set!
If you want to detach the doorbell or recharge it, please refer to the following sections.

6970312875631 360 Video Doorbell X3 - mount the dorrbell

Detach the Doorbell

  1. Use the Doorbell Detaching Pin provided if you wish to detach the doorbell from the Mounting Bracket.

    6970312875631 360 Video Doorbell X3 - detach the dorrbell

  2. Press and hold the hole on the bottom of the doorbell and then lift its bottom to take it off.

6970312875631 360 Video Doorbell X3 - detach the dorrbell 2

What is required:

6970312875631 360 Video Doorbell X3 - requried 3

How to Recharge the Doorbell

  1. Use Power adapter to Charge Doorbell6970312875631 360 Video Doorbell X3 - recharge 1
  2. Use Battery Pack to Charge Doorbell

6970312875631 360 Video Doorbell X3 - recharge 2

Doorbell LED indication Charging: Solid Red Light
Fully charged: Solid Blue Light
Doorbell Charging time 8 hours from 0% to 100%

Option 2 – Wire Powered

  1. If you have existing and working doorbell wiring at the front door, you can choose to power the doorbell by wire constantly. In this case, you don’t need to detach and charge it after installation.
  2. Since the doorbell is connected to the wires, the mounting position is limited.

6970312875631 360 Video Doorbell X3 - wire powerd

Step 1 Check Whether the Existing Doorbell Wiring Is Working

  1. Ring the existing doorbell to check if it is working. If the doorbell doesn’t ring, your doorbell wires may be defective. Power the doorbell on its own battery or consult an electrician to fix the wires.
  2. Shut off power at the breaker. Turn the lights on / off in your home to make sure the electricity in your house is properly shut off.
    6970312875631 360 Video Doorbell X3 - wiringNote: Always be careful when handling electricity wiring. If you’re not comfortable doing it yourself, do consult a qualified electrician.

Step 2 Detach the Existing Doorbell Button

If you already have existing doorbell wiring.

  1. Remove the existing doorbell button with a Phillips-Head screwdriver (not provided).
  2. Pull the two wires out carefully when removing the existing doorbell. Straighten the wire ends if necessary.

6970312875631 360 Video Doorbell X3 - doorbell button

What is required:

6970312875631 360 Video Doorbell X3 - required 4

Step 3 Find a Mounting Spot

  1. Determine the mounting position of the doorbell. Consider the factors below:
    1. Check if you can reuse the existing holes and anchors on the wall or door frame.
    2. If you are drilling the mounting holes for the first time, the recommended mounting height is 48″ / 1.2 m from the ground. (Figure 11)6970312875631 360 Video Doorbell X3 - figure 13. Use the 15° mounting wedge as a supplementary mounting bracket if you wish to see more on a specific side. (Figure 12)6970312875631 360 Video Doorbell X3 - figure 12
  2. Place the Screw Hole Positioning Card against the wall to mark the position. (Figure 13)
    6970312875631 360 Video Doorbell X3 - figure 13

Step 4 Mount the Bracket

If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill pilot holes. Use the provided screws to secure the Mounting Bracket on the wall. The Screw Hole Positioning Card gives the position of the screw holes.

6970312875631 360 Video Doorbell X3 - mounting the bracket

What is required:

6970312875631 360 Video Doorbell X3 - required 5

If you’re mounting the doorbell on a surface made out of hard materials, like brick, concrete, stucco.

  1. drill 4 holes through the Screw Hole Positioning Card with a 1 S/64″(6mm) drill bit.
  2. Insert the provided anchors, and then use the provided long screws to secure the Mounting Bracket on the wall.

6970312875631 360 Video Doorbell X3 - figure 16

6970312875631 360 Video Doorbell X3 - figure 17

What is required:

6970312875631 360 Video Doorbell X3 - required 7

Step 5 Connect the Doorbell Wires to the Doorbell

Connect the wires to the terminals at the back of the doorbell, then tighten the terminal screws. Wire can connect to any terminal.

6970312875631 360 Video Doorbell X3 - figure 18Note: 

  • To prevent short-circuit, make sure the wires are not touching each other after being connected to the terminals.
  • If the wires are too short, use the extension wires and wire nuts provided to make them longer. Use electrical wiring tape instead if there is no more space on the wall for wire nuts.

6970312875631 360 Video Doorbell X3 - figure 19

What is required:

6970312875631 360 Video Doorbell X3 - required 9

Step 6 Mount the Doorbell on the Bracket

Align the doorbell on top and then snap it on the bottom.

6970312875631 360 Video Doorbell X3 - figure 20

Step 7 Restore Power

Switch the master circuit breaker back to ON. You’re all set!
If you want to detach the doorbell or recharge it, please refer to the corresponding sections.

6970312875631 360 Video Doorbell X3 - figure 21

Notices

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  4. Consult the dealer or an experienced radio/ TV technician for help.

FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The min separation distance is 20cm. Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

PROBOAT PRB08043 BlackJack 42 Inch Brushless 8S Catamaran - icon 3This product complies with the radio interference requirements of the European Community.

  1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
  2. The product shall be connected to a USB interface of version USB2.0 or higher.
  3. Only indoor use for band 5150-5250MHz.

Declaration of Conformity

This device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site:https://www.eu­-fylife.com.
This product can be used across EU member states.
Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment.
The suitable temperature for HomeBase 2 and accessories is -10°C-45°C.
The suitable temperature for Video Doorbell 5MP (Battery-Powered) and accessories is -20°C -50°C.
When charging, please place the device in an environment that has a normal room temperature and good ventilation.
It is recommended to charge the device in an environment with a temperature that ranges from 0°C-40°C.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirements, use products that maintains a 20cm distance between the device and the human body.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

360 Video Doorbell X3 (Base Station):

Frequency bands Maximum output power (EIRP)
2412-2472Mhz 16.95 dBm
5745-5825 Mhz 9.92dBm
5150-5250 Mhz 14.11dBm

360 Video Doorbell X3 (Doorbell):

Frequency bands Maximum output power (EIRP)
2412-2472Mhz 16.58dBm

RETEKESS PR16R Megaphone Portable Voice Amplifier - 1This product is designed and manufactured with high-quality materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling.
PROBOAT PRB08043 BlackJack 42 Inch Brushless 8S Catamaran - icon 2Proper disposal and recycling help protect natural resources, human health, and the environment. For more information on the disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.”
IC RF Statement
When using the product maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de (‘utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matiere d’exposition RF.

Customer Service

6970312875631 360 Video Doorbell X3 -icon 1Warranty
12-month limited warranty
6970312875631 360 Video Doorbell X3 -icon 2Official site: smart.360.com
facebook icon [email protected]
6970312875631 360 Video Doorbell X3 -icon 3[email protected]

TCL HH42CV1 Link Hub - icon 8Customer Support: [email protected]
Amazon Customer Support: [email protected]

Company: Beijing Visual World Technology Co., Ltd.
Address: 1721 and 15th floor, Build 3, No.10 (A) jiuxianqiao Road, Chaoyang District, Beijing, China

Documents / Resources

360 6970312875631 360 Video Doorbell X3 [pdf] User Guide
AR3X-2, AR3X2, 2AIV9-AR3X-2, 2AIV9AR3X2, AR3X-1, AR3X1, 2AIV9-AR3X-1, 2AIV9AR3X1, 6970312875631 360 Video Doorbell X3, 360 Video Doorbell X3

Leave a comment

Your email address will not be published.