2 in 1 Infrared Thermometer Ear and Object KI-8171L Instruction Manual

Infrared Thermometer Ear and Object KI-8171L

Instruction Manual

2 in 1 Infrared Thermometer

2 in 1 Infrared Thermometer Ear and Object
Model : KI-8171L

Precautions

  1. Please consult your physician to verify your body temperature.
  2. DO NOT scrape or scratch the lens as it will hamper the effectiveness of the device.
  3. The device is intended for consumer use only.
  4. Do not drop or expose thermometer to electric shock as this may adversely affect its performance.

POWER SOURCE SIZE AAA(1.5V)x 2
WARRANTY: ONE YEAR FROM THE DATE OF PURCHASE

Parts Identification

Parts Identification

About IR and Body Temperature
Why an IR ear thermometer?
The tympanic membrane (eardrum), and the hypothalamus, the part of the brain which controls body temperature, share a common blood supply so tympanic readings rise and fall rapidly with core temperature (deep body temperature). This makes the ear temperatures one of the best indicators of internal body (core) temperature.

What are normal temperature values?
Human body temperature varies from person to person, some run in the lower range (96-97°F) and some run in the higher range (98-99°F). Also, your normal body temperature changes throughout the day and can vary at different times of the year. It is very important to know your normal body temperature range. We recommend measuring yourself when healthy to establish reference temperatures. This will help you feel more confident of the measured temperature readings when ill.

Information You Should Know Before Operating the IR Ear Thermometer
How to correctly use the IR ear thermometer

  1. It is useful to try this thermometer on yourself first to become familiar with it’s operations.
  2. Do not take the temperature immediately upon waking. Sleeping on the ear can cause the temperature to be higher than normal.
  3. It is common for the readings to be slightly different between the right and left ear. We suggest using the same ear to obtain temperature readings.
  4. Straighten the ear canal for measuring: Children under 12 months: Straighten ear canal by gently pulling the ear back.
Ear Back

Children over 12 months and Adults: Straighten the ear canal by gently pulling the ear back and up.

Ear Back and Up

6. Make sure the ear canal is dry, clean and free of was or particulates.

Preparation for Use
Installing/Replacing the Battery:

  1. Slide the battery cover off in the direction shown below.
  2. If replacing, carefully remove batteries.
  3. Clean the battery ends as well as the contacts in the device prior to reinstalling batteries.
  4. Install two new AAA batteries into the battery compartment making sure to match the correct polarities (+ and -).
  5. Replace and securely fasten the battery cover as shown below.
Replacing the Battery

WARNING:
Batteries Contain Mercury. DO NOT PUT IN REGULAR TRASH, dispose of in recycling trash only. Recycle or manage as hazardous waste. Never dispose of batteries in fire. Do not recharge (unless rechargeable), put in backwards or disassemble. This may cause explosion, leakage and injury.

CAUTION:
When replacing batteries, do not mix old ones and new ones. Never mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

How to Operate the Thermometer
NOTE: Each time you turn on the unit, it will automatically run a diagnostic check and the screen will show colors and all symbols:

symbols

QUICK START

  1. Press and release the POWER button. You will hear a short beep and the memory will show the last temperature taken.
  2. Place the Probe inside the ear canal or aim toward the object approximately – 1 ‘/x inches (1- 3 cm) from surface.
  3. Press and release the POWER button to record new measurement.
  4. Two short beeps let you know the measurement is complete/ready to read.
  5. The temperature and back light color shows on the display. The back light color will light according to the reading:
Color Table

6. Turn the unit off by pressing and holding the POWER button for about 5 seconds until the display shows OFF and a long beep is heard.

OFF

7. The device will automatically shut off after about 1 minute of non-use.

SETTING THE SCALE °C or °F

  1. Press and release the POWER button to turn on the device.
  2. Immediately press it again and hold down until you see the °C or °F change. Release the button as soon as change occurs.
SETTING THE SCALE

3. The device is now ready to take a measurement.

CHANGING MODES
This device has two modes: (1)Ear (2)Object

  1. Ear mode is for measuring temperature of the tympanic membrane (eardrum) to determine body temperature.
  2. Object mode is for measuring temperature of an object or surface. This mode is not intended for measuring human body temperature.

*Device will always power on in Ear Mode*

  1. Press and release the POWER button to turn on the device.
  2. Immediately press and hold the Memory/Mode button until you see either
Memory

then release button.

3. You may toggle between modes simply by following step 2.

RECALL MEMORIES
This device will hold 10 temperature readings in memory (Ear and Object readings combined).
• Ear memories will show the small .111 ear icon in the top right side of display.
• Object memories show nothing in that area.

  1. The device must be powered OFF in order to recall memories.
  2. Simply press and release the Memory/Mode button to show stored temperature readings.
  3. The most recent temperature reading will be the first to show.
  4. When viewing memory, the device will automatically shut off after 3 seconds of non-use.

DELETE MEMORIES

  1. Repeat steps land 2 in “Recall Memories”
  2. Press and hold the Power button until “dEL” is displayed.
  3. Release button. All stored memories are now deleted Device will automatically shut off.
DELETE MEMORIES

IMPORTANT THINGS TO KNOW

  • Allow at least 1-3 minutes between each measurement in order to obtain the most accurate result.
  • The default mode is Ear mode. Any time the unit is powered off, it will power on in ear mode.
  • Make sure the probe lens is clean and clear before use. It should be ‘mirror like’ or reflective. A dirty, blocked or scratched lens will cause incorrect results.
  • Do not store the device in extreme conditions or temperatures (ie., direct sunlight, very hot/cold or high moisture like a bathroom). Unit is not waterproof.
  • If it has been stored in extreme conditions, wait at least one hour for it to return to a normal room temperature before using.
  • Wait at least thirty minutes after bathing, exercising or eating before taking a measurement. . Do not dismantle or modify the device other than changing the batteries.
  • This device has no user serviceable parts. Do not dismantle or modify other than changing the batteries.

CLEANING AND CARE

CLEANING AND CARE

ERROR MASSAGE

ERROR  MASSAGE

SPECIFICATIONS

SPECIFICATIONS

LIMITED WARRANTY
This device (batteries excluded) is guaranteed for one year from the data of purchase against manufacturer’s defect under normal use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device is not properly operated according to the instructions as described in this manual.
• Device shows any signs of tampering or attempted modification.
• Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage.
• Natural disasters (such as fire, flood, earthquake, lightening).
• Na receipt or proof of purchase showing dote of purchase

Following the instructions closely will ensure years of dependable operation.

FCC STATEMENT

POTENTIAL FOR RADIOS/TELEVISION INTERFERENCE (For USA Only)
Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protector against harmful interference in a residential The product generates, LISPS, and ran radiate radio frequency energy and, T not installed and used in accordance with the Instructions, may cause harmful Interference to tad e communicator, However, there is no guarantee that Interference will not occur In a particular installation, If the product does cause harmful Interference to radio or television receptor, which can be determined by turnings the product on and oft the user is encouraged to try to correct the interference by one or more of the following measure:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio / TV technician for help.

Questions about your Manual ? Post in the comments!

Sonic Toothbrush SG-932 Instruction Manual

INSTRUCTION MANUAL

Sonic Toothbrush

Sonic Toothbrush Model : SG-932

Identifying the Parts
A. Brush head
B. Power button
C. Battery cover
D. Protective cover

How to change the replaceable brush head

  1. Turn brush head counter clockwise (1)
  2. and pull up . (2)
  3. Align the new brush head (1)
  4. and turn it clockwise (2)
How to change the  replaceable brush head

Notch on neck should align with inner notches of toothbrush head to lock in place.

Replacing the Battery
Turn battery cover clockwise as directed (1) and disconnect as shown (2). Insert a new AAA battery with polarity as indicated. Replace the battery cover as shown(3) and turn it firmly counter-clockwise as directed(4).

Features
• Toothbrush vibration rate: 22,000 brush strokes per minute.
• Replaceable brush head
• Battery: one AAA type battery

Toothbrush Safety Use and Care

  1. Contact your dentist before using this device if you have had oral or periodontal surgery.
  2. This device is designed for cleaning teeth and gums only. DO NOT use for any other purposes.
  3. This toothbrush can be used with any brand of toothpaste/gel.
  4. Wash or rinse the brush head before your initial use.
  5. Move the brush gently along your teeth and gum line in a slight circular motion and allow the vibration of the toothbrush to do the work. Do not press bristles hard against teeth or gums.
  6. After brushing with toothpaste, thoroughly rinse brush head and handle and then dry. This helps prevent toothpaste residue buildup which can cause the unit to not function effectively.
  7. Close supervision is necessary when this product is used by or on small children.

NOTE: Upon first use, you may experience slight bleeding. This should stop after a few days. If it continues after the first week, or if excessive bleeding occurs, stop using and contact your dentist

Caution / Helpful Information
*This device has no user serviceable parts. Any modifications will void the warranty.
*Avoid placing or storing the unit in high heat or direct sunlight.

  • Do not place or store device where it can fall or be pulled into a sink or tub.
  • Do not place in or drop into water or other liquid. Device is WATER RESISTANT, not water proof.
  • Never replace the battery with wet hands. It will cause the battery to malfunction.
  • Never operate this device if it has a damaged or cracked housing or if it is not working properly.
  • If the power (battery) is low, the vibration frequency of the device will be reduced or stopped. This is not a malfunction, change the battery.
    *Thoroughly clean and dry the toothbrush and cover and remove the battery before storing for an extended period of time.

Dispose of the battery in compliance with your national or local regulations for environmental protection and recycling of raw materials.

FCC STATEMENT
This device has been tested and complies with the requirements for Federal Communications Commission, Part 18 for Radlo/TV/ Communication [19/T/C] interference. Although tested, it may affect RfT/C. If it does interfere, separate R/T/C from the device.

CAUTION: Conduct only user maintenance found in these instructions. Other maintenance or servicing can cause harmful interference and can void the required FCC compliance.

LIMITED WARRANTY

This device (excluding battery) is guaranteed for ONE year from the date of purchase against manufacturer’s defect under normal use as outlined in these instructions. Following the instructions closely will ensure years of dependable operation.

If the device does not function properly, please contact Our rep will provide further instruction on how to correct the trouble or will ask you to return it for repair or warranty replacement. A copy of the receipt showing date of purchase is required for warranty replacement, no exceptions.

Questions about your Manual ? Post in the comments!

Sonic Toothbrush 421.RA Instruction Manual

Sonic Toothbrush

INSTRUCTION MANUAL

Sonic Toothbrush 421.RA

Sonic Toothbrush Model : 421.RA

  • 2 MINUTE TIMER
  • 3 SETTINGS HANDLE
  • UV TOOTHBRUSH
  • SANITIZING BASE

READ AND SAVE ALL INSTRUCTIONS BEFORE USING THIS DEVICE TO ENSURE SAFETY AND EFFECTIVENESS

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, especially when children are present, basic safety
precautions should always be used, including the following:

WARNING – To reduce the risk of fire, electric shock, or injury:

  1. Do not leave plugged in device unattended for a long period of time. Unplug from outlet when not in use and before cleaning.
  2. Do not allow device to be used as a toy. Close attention is necessary when used by or near children.
  3. Use this device only as described in this manual.
  4. Use only approved replacement brush heads designed to work with this handle and base.
  5. Turn off the device before unplugging.
  6. Do not use with damaged cord or plug. If device is not working properly, refer to the LIMITED WARRANTY section on the last page
    of this instruction manual for further information.
  7. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
  8. Do not unplug by pulling on cord. Grasp and pull the plug not the cord.
  9. Never handle plug or Charging Base with wet hands.
  10. Keep cord away from heated surfaces.
  11. This device has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to tamper with this safety feature.
  12. Do not use when feeling drowsy or sleepy.
  13. Do not use this product outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
  14. Never block the air openings of this device. When plugged in, device must always be placed on a firm counter or table with room around it for proper air circulation. Never place on a soft surface, such as a bed or couch, or where towels or cloths can restrict air circulation.
  15. Keep the air openings free of lint and the like.
  16. Never drop or insert any object into any opening.
  17. DO NOT fill this device with water or submerge in water or other liquid.

Danger – This section applies to Charging Base only To reduce the risk of electrocution:

  1. Always unplug the device after sanitizing brush heads, after charging handle or if it will be left unattended for a long pe riod of time.
  2. Do not use while bathing.Do not place or store device where it can fall or be pulled into a tub or sink.
  3. Do not place in or drop into water or other liquid.
  4. NEVER reach for any electrical device that has fallen into water. Unplug immediately.

WARNING:

Risk of exposure to excessive ultraviolet (UV) radiation – To avoid exposure, do not operate if the lid of the UV Base is not completely closed and in the correct position or if lamp is damaged. The lid of the base is equipped with an interlocking system to reduce the risk of excessive ultraviolet radiation – DO NOT attempt to defeat its purpose. Replacement of the Lamp is intended for qualified personnel only. Do not attempt to service yourself. Service personnel: There is risk of exposure to ultraviolet radiation.

LIST OF MAIN PARTS

LIST OF MAIN PARTS
  1. Brush Head
  2. Power Handle
  3. UV Storage Compartment Lid
  4. UV Charging Base / Storage Compartment
    (holds 2 brush heads)
  5. LED Charging Indicator Light
  6. LED Mode Indicator Lights H – High; M – Medium; L – Low
  7. Power Button – ON / OFF / MODE selection
  8. Power Cord location
  9. UV Lamp Indicator

TECHNICAL SPECIFICATIONS
Rating Voltage : 120V
Frequency : 60Hz
Power : 2.5W
Auto Shut-off Duration : 2 Minutes
3 Pulse signal Duration : Every 30 Seconds
Full Charge Time : 16 Hours
Re-chargeable Battery Ni-Cd, 600mAh
UV Lamp 254 nm wave-length
Auto ON when the Lid is closed
Auto OFF when the Lid is open
Auto Shut-off after 10 minutes
UV lamp indicator turns off when UV lamp inside storage UV compartment is off

CONTENTS OF PACKAGING

  1. Instruction Manual
  2. Charging Base/Storage UV compartment with Lid
  3. Power H handle
  4. 4 Brush Heads

OPERATION AND USE

Charging Your Toothbrush

  1. Plug in the Charging Base to electrical outlet.
  2. When you place the Handle on the Charging Base, the LED Charging Indicator Light will illuminate, indicating the Handle is charging. NOTE: light does not turn off when charging is complete.
  3. To obtain maximum power of brushing, we recommend keeping your handle on the Charging Base until full battery charge is
    achieved. Unplug after full battery charge is achieved or if device will be left unattended for long periods of time such as vacation.
  4. It requires about 16 hours for your Sonic Toothbrush to be fully charged for the first use or when your rechargeable battery completely runs down.
  5. You should allow a full discharge of your Sonic Toothbrush at least every six months in order to maintain the maximum capacity of the rechargeable battery. Simply unplug your charging base and allow the brush to run down with normal use.
  6. For the correct voltage use, please refer to the bottom of the Charging Base.

Mode Selection

  1. Press Power Button 1 time …………High Speed (H)…………… H LED lights up.
  2. Press Power Button 2 times………. Medium Speed (M)………. M LED lights up.
  3. Press Power Button 3 times………. Lower Speed (L)…………. L LED lights up.
  4. Press Power Button 4 times………. OFF…………………………LED lights go out.

How To Use Your Toothbrush

  1. Insert Brush Head on the shaft of the Handle. There will be a small space (1mm) between the Brush Head and the Handle. The
    space allows a free motion of the Brush Head during brushing.
  2. Apply toothpaste onto the Brush Head prior to turning the unit on.
  3. Put the Brush Head into your mouth before switching on your Sonic Toothbrush.
  4. Move the Brush Head gently along your teeth and gum line region and allow the Brush Head to stay on the surface of each tooth for a few seconds with a slight circular motion for the best cleaning and gum massaging effect.
  5. DO NOT forget to reach all areas of your teeth including the inner and chewing surfaces and behind the back teeth.
  6. After use, turn off your Sonic Toothbrush and thoroughly rinse brush head and handle under a tap to remove all paste/gel. Wipe dry.

NOTE: When you first use your Sonic Toothbrush you may experience slight bleeding. This should stop after a few days when your gums get used to the toothbrush. If the bleeding persists, please consult your dentist or hygienist.

How To Sanitize Your Brush Heads

  1. Sanitize the Brush Heads be fore using your Sonic Toothbrush for the first time.
  2. Open the Lid and insert the Brush Heads to the small shafts on the bottom of the storage UV compartment. Make sure the bristles of Brush Head are facing the UV Lamp located in the middle.
  3. Close the Lid, the UV Lamp and the Lamp Indicator light will illuminate automatically. The UV Lamp and Indicator light will shut off after approximately 10 minutes. If the Lid is accidentally opened during operation, the Lamp and Indicator light will automatically turn off.
  4. We recommend sanitizing the Brush Heads often, or after each use when there is sick ness in your household.

Cleaning And Maintenance

  1. Disconnect the Charging Base power cord from power supply.
  2. During the cleaning procedures, avoid getting the plug and power cord wet.
  3. Brush Heads: R emove head from Handle by pulling straight off, DO NOT twist. This may break the shaft and will void the warranty. After each use, remove and thoroughly rinse Brush Head under running water. We recommend soaking the brush head in a denture cleaner (commercially available) every 2 to 4 weeks to keep it hygienically clean.
  4. Charging Base: Periodically clean th e Charging Base with a soft cloth or paper towel. Ensure that the Charging Base is completely dry before plugging into any electrical outlet.
  5. Power Handle: Rinse and wipe the Handle clean after each use. Be sure to rinse and wipe the shaft where the brush head attaches to the handle after each use. This will keep you from having toothpaste buildup which can interfere with the proper operation of the device.
  6. UV/Brush Compartment area of Charging Ba se: Periodic cleaning of the Storage UV Compartment is recommended. Interior may be cleaned using a soft cloth or paper towel. Use a cotton swab to remove stubborn residue in hard to reach areas. Any water being splashed or poured directly on the UV lamp should be avoided. Allow interior and exterior to dry completely before plugging back into the electrical outlet.
  7. When the Toothbrush is not in use for an extended period, unplug the cord and place the product in a safe dry place. DO NOT wrap the cord around the device.
  8. This product is for home use only.
  9. This product has NO USER SERVICEABLE parts. Any modifications to the device by an unauthorized person may cause it to function improperly and WILL void the warranty.

IMPORTANT MEDICAL SAFEGUARDS
Please note the following instructions for your continued safety:

  1. Contact your dentist before using the Sonic Toothbrush if you have had oral or periodontal surgery.
  2. Contact your dentist if excessive bleeding occurs or if bleeding continues after the first week of using the Sonic Toothbrush.
  3. If you have any questions concerning usage with a pacemaker, consult your physician prior to use.
  4. This product is designed for cleaning teeth and gums only. DO NOT use for any other purposes as this will void the warranty.
  5. The Sonic Toothbrush can be used with any leading brand of toothpaste.

Special Instructions
Removing and disposing of Ni-Cd Battery Your Sonic Toothbrush is equipped with a long-lasting rechargeable Nickel-Cadmium battery. To help protect our environment, it should be removed at the end of the device’s life for safe dispos al.

This battery CANNOT be replaced.

To remove the battery before discarding the product:

  1. Open the battery cover at the bottom of the Handle using a Phillips screwdriver to remove the screw.Remove end cap.
  2. Pull out the Ni-Cd battery. If the battery does not slide out easily, firmly shake the handle up and down or tap on a firm surface to dislodge. Once the battery is pulled out, clip the two wires to separate the battery from inside the Handle.
  3. Dispose of the battery in compliance with your national or local regulations for environmental protection and recycling of raw materials.

To remove the battery before discarding the product:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference
that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

  • These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses, generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna
  • Increase the separation between the equipment and receiver
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
  • Consult the dealer or an experienced radio/TV technician for help

Complies to US Federal requirements, including 21 CFR, Chapter 1, Subchapter J, Radiological Health.

LIMITED WARRANTY
This device is guaranteed for ONE year from the date of purchase against manufacturer’s defect under normal use as outlined in these instructions. Following the instructions closely will ensure years of dependable operation.

  1. This device is designed for household use only, not commercial.
  2. This warranty does not apply to damage resulting from abusive, commercial or unreasonable use.
  3. Problems that are the result of normal wear and tear will not be considered manufacturing defects under this warranty.
  4. At the discretion of 180 INNOVATIONS, we will repair or replace this device if material or workmanship is found to be defective.
  5. This warranty does not cover damage caused by dropping, leaving outdoors, improper storage in extreme temperatures or dropping in water.
  6. This warranty does not cover damage resulting from any attempts to repair or modify the device and it’s parts.
  7. It is at the full discretion of 180 INNOVATIONS to determine if any visible or notable attempts have been made to repair, modify, alter or disassemble any part of the device, therefore voiding the warranty.

All returned items must include:

Full name, address and daytime phone number >
Short explanation of malfunction
Proof of purchase with date – NO exception

Packet

Questions about your Manual ? Post in the comments!

Quip Toothbrush Instruction Manual: Changing Battery & Brush

Step 1: Remove old brush head

Grip the head and handle in opposite hands, bristles facing away from you. Place your thumb on the dots, then gently pull the head off in a slight arc motion (don’t snap it directly backwards).

Refill-1.gif

Step 2: Remove motor and battery

Pull the motor out by lifting it by the wings or using the thumbnail notch. Once it’s removed, tip the handle over and tap out the battery.

Refill-2.gif

Step 3: Clean brush handle

Lightly wet the bristles on your old brush head, and use it to gently scrub away any dried toothpaste from the top white portion of the handle.

Refill-3.gif

Step 4: Replace motor and battery

Drop in a new AAA battery or a fresh rechargeable negative end first, then slide the motor back in (it will spring up slightly).

Refill-4.gif

Step 5: Apply fresh brush head

Push on your new brush head until it’s flush with the handle and you hear a dull click. Press the “q” to test, then you’re set. Happy brushing 🙂

Refill-5.gif

Sonic Toothbrush 421F Instruction Manual

Sonic Toothbrush

INSTRUCTION MANUAL

Sonic Toothbrush
Battery Operated
Model : 421F

READ ALL INSTRUCTIONS BEFORE USING THIS DEVICE TO ENSURE SAFETY AND EFFECTIVENESS

IDENTIFYING THE PARTS

IDENTIFYING THE PARTS
  1. Protective Cover for brush head
  2. Brush Head
  3. Shaft
  4. Power Button — Power ON/OFF
  5. Handle
  6. AAA Battery
  7. Battery Cover/Handle

REMOVE PROTECTIVE COVER FROM BATTERY !

TOOTHBRUSH BASICS

  1. Insert 1 AAA battery hold Handle with the ON/OFF button facing you. Gently twist the Battery Cover/Handle clockwise to unlock. Gently remove the Battery Cover/Handle from the Handle. Insert battery being careful to match the polarity ) as indicated.
  2. Gently replace Battery Cover/Handle onto the Handle over the battery, tuming counter clockwise until locked into place.
  3. Insert a brush head onto the Handle; Hold Handle with ON/OFF button facing you. Hold Brush Head with bristles facing right gently lowering the Brush Head onto the shaft of the Handle. When it wont go any lower, slowly begin taming the Brush Head clockwise so bristles are facing you. As you turn it, the Brush Head will easily lock down into place.
  4. Wash or rinse the brush head before your initial use.
  5. After brushing with toothpaste, thoroughly rinse the brush head and handle to prevent toothpaste residue buildup. This can cause the unit to not function effectively.
  6. Close supervision is necessary when this product is used by. on, or near small children or invalids.
  7. Never operate this product if, it has a damaged or cracked housing; if it is not working properly.
  8. Never use while feeling drowsy.
  9. Do not place or store product where it can fall or be pulled into a sink or tub.
  10. Do not place in or drop into water or other liquid. Device is water resistant, not water proof.
  11. Use this product only for its intended use as described in this manual.

USING YOUR TOOTHBRUSH

  1. Apply toothpaste onto the Brush Head and put into your mouth prior to turning the unit on.
  2. Move the Brush Head gently along your teeth and gum line region and allow the Brush Head to stay on the surface of each tooth for a few seconds with a slight circular motion for the best cleaning and gum massaging effect.
  3. Don’t forget to reach all areas of your teeth including the inner and chewing surfaces and behind the back teeth. A No minute brushing cycle is normally optimum for clean teeth health.
  4. After use, turn off your Sonic Toothbrush and thoroughly rinse brush head and handle under running water. Wipe the Handle dry and replace the Protective Cover.

NOTE: When you first use your Sonic Toothbrush you may experience slight bleeding. This should stop after a few days when your gums get used to the toothbrush. If excessive bleeding occurs or if bleeding continues after the first week of use, contact your dentist or hygienist.

TECHNICAL SPECIFICATION
Battery : 1 AAA Alkaline, 1.5VDC (Included)
Battery Duration : Approx. 80 cycles (2 min. per cycle)
Settings : ON/OFF

CONTENTS OF PACKAGE

  1. Instruction Manual
  2. Handle
  3. Protective Cover
  4. Brush Heads (2)
  5. AAA Battery (1)

Cleaning And Maintenance

  1. Cleaning: After each use follow cleaning instructions as described in “USING YOUR TOOTHBRUSH” /M. We recommend soaking the brush head in a denture cleaner (commercially available) every 2 to 4 weeks to keep it hygienically clean.
  2. Protective Cover: Periodically clean the interior of the Protective Cover that covers the brush head to help in the prevention of mold, mildew or germ buildup. This can be done with a bottle bush and dish detergent, then rinse with warm to hot water. Wipe dry with a soft cloth or paper towel.
  3. When the Toothbrush will not be used for an extended period of time, remove battery and store in a safe dry place.
  4. This product has no user serviceable parts.

IMPORTANT SAFEGUARDS
Please note the following Instructions for your continued safety:

  1. Contact your dentist before using the Sonic Toothbrush if you have had oral or periodontal surgery.
  2. This product is designed for cleaning teeth and gums only. DO NOT use for any other purposes.
  3. The Sonic Toothbrush can be used with any leading brand of toothpaste.

BATTERY DISPOSAL

Dispose of the battery in compliance with your national or local regulations for environmental protection and recycling of raw materials.

FCC STATEMENT
This device has been tested and complies with the requirements for Federal Communications Commission, Part 18 for Radio/TV/Communication interference. Although tested, it may affect RadionV/Communication. If it is found to interfere, separate the RadionV/Communloalion from the device.

CAUTION:
Conduct only user maintenance found in this manual. Other maintenance and servicing can cause harmful interference and can void the required FCC compliance.

LIMITED WARRANTY
This device is guaranteed for ONE year from the date of purchase against manufacturers defect under normal use as outlined in these instruction. Following the instructions closely will ensure years of dependable operation.

Questions about your Manual ? Post in the comments!

Sonic Toothbrush 421B Instruction Manual

Sonic Toothbrush

INSTRUCTION MANUAL

Sonic Toothbrush 421B

Sonic Toothbrush Model: 421B

  • 2 MINUTE TIMER
  • 3 SETTINGS HANDLE
  • UV TOOTHBRUSH
  • SANITIZING BASE

READ AND SAVE ALL INSTRUCTIONS BEFORE USING THIS DEVICE TO ENSURE SAFETY AND EFFECTIVENESS

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, especially when children are present, basic safety
precautions should always be used, including the following:

WARNING – To reduce the risk of fire, electric shock, or injury:

  1. Do not leave plugged in device unattended for a long period of time. Unplug from outlet when not in use and before cleaning.
  2. Do not allow device to be used as a toy. Close attention is necessary when used by or near children.
  3. Use this device only as described in this manual.
  4. Use only approved replacement brush heads designed to work with this handle and base.
  5. Turn off the device before unplugging.
  6. Do not use with damaged cord or plug. If device is not working properly, refer to the LIMITED WARRANTY section on the last page
    of this instruction manual for further information.
  7. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
  8. Do not unplug by pulling on cord. Grasp and pull the plug not the cord.
  9. Never handle plug or Charging Base with wet hands.
  10. Keep cord away from heated surfaces.
  11. This device has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only
    one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt
    to tamper with this safety feature.
  12. Do not use when feeling drowsy or sleepy.
  13. Do not use this product outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
  14. Never block the air openings of this device. When plugged in, device must always be placed on a firm counter or table with room around
    it for proper air circulation. Never place on a soft surface, such as a bed or couch, or where towels or cloths can restrict air circulation.
  15. Keep the air openings free of lint and the like.
  16. Never drop or insert any object into any opening.
  17. DO NOT fill this device with water or submerge in water or other liquid.

Danger – This section applies to Charging Base only To reduce the risk of electrocution:

  1. Always unplug the device after sanitizing brush heads, after charging handle or if it will be left unattended for a long pe riod of t ime.
  2. Do not use while bathing.
  3. Do not place or store device where it can fall or be pulled into a tub or sink.
  4. NEVER reach for any electrical device that has fallen into water. Unplug immediately.

WARNING:

Risk of exposure to excessive ultraviolet (UV) radiation – To avoid exposure, do not operate if the lid of the UV Base is not completely closed and in the correct position or if lamp is damaged. The lid of the base is equipped with an interlocking system to reduce the risk of excessive ultraviolet radiation – DO NOT attempt to defeat its purpose. Replacement of the Lamp is intended for qualified personnel only. Do not attempt to service yourself. Service personnel: There is risk of exposure to ultraviolet radiation.

THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

LIST OF MAIN PARTS

LIST OF MAIN PARTS
  1. Brush Head
  2. Power Handle
  3. UV Storage Compartment Lid
  4. UV Charging Base / Storage Compartment
    (holds 2 brush heads)
  5. LED Charging Indicator Light
  6. LED Mode Indicator Lights H – High; M – Medium; L – Low
  7. Power Button – ON / OFF / MODE selection
  8. Power Cord location
  9. UV Lamp Indicator

TECHNICAL SPECIFICATIONS

Rating Voltage : 120V
Frequency : 60Hz
Power : 2.5W
Auto Shut-off Duration : 2 Minutes
3 Pulse signal Duration : Every 30 Seconds
Full Charge Time : 16 Hours
Re-chargeable Battery : Ni-Cd, 600mAh
UV Lamp 254 nm wave-length
Auto ON when the Lid is closed
Auto OFF when the Lid is open
Auto Shut-off after 10 minutes
UV lamp indicator turns off when UV lamp inside storage UV compartment is off

CONTENTS OF PACKAGING

  1. Instruction Manual
  2. Charging Base/Storage UV compartment with Lid
  3. Power H andle
  4. 4 Brush Heads

OPERATION AND USE

Charging Your Toothbrush

  1. Plug in the Charging Base to electrical outlet.
  2. When you place the Handle on the Charging Base, the LED
    Charging Indicator Light will illuminate, indicating the Handle is
    charging. NOTE: light does not turn off when charging is complete.
  3. To obtain maximum power of brushing, we recommend keeping
    your handle on the Charging Base until full battery charge is
    achieved. Unplug after full battery charge is achieved or if device
    will be left unattended for long periods of time such as vacation.
  4. It requires about 16 hours for your Sonic Toothbrush to be fully
    charged for the first use or when your rechargeable battery
    completely runs down.
  5. You should allow a full discharge of your Sonic Toothbrush at least
    every six months in order to maintain the maximum capacity of the
    rechargeable battery. Simply unplug your charging base and allow
    the brush to run down with normal use.
  6. For the correct voltage use, please refer to the bottom of the
    Charging Base.

Mode Selection

  1. Press Power Button 1 time …………High Speed (H)…………… H LED lights up.
  2. Press Power Button 2 times………. Medium Speed (M)………. M LED lights up.
  3. Press Power Button 3 times………. Lower Speed (L)…………. L LED lights up.
  4. Press Power Button 4 times………. OFF…………………………LED lights go out.

How To Use Your Toothbrush

  1. Insert Brush Head on the shaft of the Handle. There will be a small space (1mm) between the Brush Head and the Handle. The
    space allows a free motion of the Brush Head during brushing.
  2. Apply toothpaste onto the Brush Head prior to turning the unit on.
  3. Put the Brush Head into your mouth before switching on your Sonic Toothbrush.
  4. Move the Brush Head gently along your teeth and gum line region and allow the Brush Head to stay on the surface of each tooth for a
    few seconds with a slight circular motion for the best cleaning and gum massaging effect.
  5. DO NOT forget to reach all areas of your teeth including the inner and chewing surfaces and behind the back teeth.
  6. After use, turn off your Sonic Toothbrush and thoroughly rinse brush head and handle under a tap to remove all paste/gel. Wipe dry.
    NOTE: When you first use your Sonic Toothbrush you may experience slight bleeding. This should stop after a few days when your
    gums get used to the toothbrush. If the bleeding persists, please consult your dentist or hygienist.

How To Sanitize Your Brush Heads

  1. Sanitize the Brush Heads be fore using your Sonic Toothbrush for the first time.
  2. Open the Lid and insert the Brush Heads to the small shafts on the bottom of the storage UV compartment. Make sure the bristles of Brush Head are facing the UV Lamp located in the middle.
  3. Close the Lid, the UV Lamp and the Lamp Indicator light will illuminate automatically. The UV Lamp and Indicator light will shut off after approximately 10 minutes. If the Lid is accidentally opened during operation, the Lamp and Indicator light will automatically turn off.
  4. We recommend sanitizing the Brush Heads often, or after each use when there is sickness in your household.

Cleaning And Maintenance

  1. Disconnect the Charging Base power cord from power supply.
  2. During the cleaning procedures, avoid getting the plug and power cord wet.
  3. Brush Heads: R emove head from Handle by pulling straight off, DO NOT twist. This may break the shaft and will void the warranty. After each use, remove and thoroughly rinse Brush Head under running water. We recommend soaking the brush head in a denture cleaner (commercially available) every 2 to 4 weeks to keep it hygienically clean.
  4. Charging Base: Periodically clean th e Charging Base with a soft cloth or paper towel. Ensure that the Charging Base is completely dry before plugging into any electrical outlet.
  5. Power Handle: Rinse and wipe the Handle clean after each use. Be sure to rinse and wipe the shaft where the brush head attaches to the handle after each use. This will keep you from having toothpaste buildup which can interfere with the proper operation of the device.
  6. UV/Brush Compartment area of Charging Ba se: Periodic cleaning of the Storage UV Compartment is recommended. Interior may be cleaned using a soft cloth or paper towel. Use a cotton swab to remove stubborn residue in hard to reach areas. Any water being splashed or poured directly on the UV lamp should be avoided. Allow interior and exterior to dry completely before plugging back into the electrical outlet.
  7. When the Toothbrush is not in use for an extended period, unplug the cord and place the product in a safe dry place. DO NOT wrap the cord around the device.
  8. This product is for home use only.
  9. This product has NO USER SERVICEABLE parts. Any modifications to the device by an unauthorized person may cause it to function improperly and WILL void the warranty.

IMPORTANT MEDICAL SAFEGUARDS

Please note the following instructions for your continued safety:

  1. Contact your dentist before using the Sonic Toothbrush if you have had oral or periodontal surgery.
  2. Contact your dentist if excessive bleeding occurs or if bleeding continues after the first week of using the Sonic Toothbrush.
  3. If you have any questions concerning usage with a pacemaker, consult your physician prior to use.
  4. This product is designed for cleaning teeth and gums only. DO NOT use for any other purposes as this will void the warranty.
  5. The Sonic Toothbrush can be used with any leading brand of toothpaste.

Special Instructions
Removing and disposing of Ni-Cd Battery

Your Sonic Toothbrush is equipped with a long-lasting rechargeable Nickel-Cadmium battery. To help protect our environment, it should be removed at the end of the device’s life for safe disposal.

This battery CANNOT be replaced.

To remove the battery before discardi ng the product:

  1. Open the battery cover at the bottom of the Handle using a Phillips screwdriver to remove the screw.Remove end cap.
  2. Pull out the Ni-Cd battery. If the battery does not slide out easily, firmly shake the handle up and down or tap on a firm surface to dislodge. Once the battery is pulled out, clip the two wires to separate the battery from inside the Handle.
  3. Dispose of the battery in compliance with your national or local regulations for environmental protection and recycling of raw materials.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference
that may cause undesired operation.

CAUTION: Modifications not approved by 180 INNOVATIONS could void user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses, generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna
  • Increase the separation between the equipment and receiver -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
  • Consult the dealer or an experienced radio/TV technician for help

Complies to US Federal requirements, including 21 CFR, Chapter 1, Subchapter J, Radiological Health.

LIMITED WARRANTY
This device is guaranteed for ONE year from the date of purchase against manufacturer’s defect under normal use as outlined in these instructions. Following the instructions closely will ensure years of dependable operation.

  1. This device is designed for household use only, not commercial.
  2. This warranty does not apply to damage resulting from abusive, commercial or unreasonable use.
  3. Problems that are the result of normal wear and tear will not be considered manufacturing defects under this warranty.
  4. At the discretion of 180 INNOVATIONS, we will repair or replace this device if material or workmanship is found to be defective.
  5. This warranty does not cover damage caused by dropping, leaving outdoors, improper storage in extreme temperatures or dropping in water.
  6. This warranty does not cover damage resulting from any attempts to repair or modify the device and it’s parts.
  7. It is at the full discretion of 180 INNOVATIONS to determine if any visible or notable attempts have been made to repair, modify, alter or
    disassemble any part of the device, therefore voiding the warranty.

** All returned items must include: > Full name, address and daytime phone number > Short explanation of malfunction >Proof of purchase with date – NO exceptions

Questions about your Manual ? Post in the comments!

Electronic Glass Scale 8188A Instruction Manual

Electronic Glass Scale
Model : 8188A

Instructions for use

Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product.

NEW FEATURE

This scale features our convenient step-on operation. Once initialized, the scale can be operated by simply stepping straight onto the platform – no more waiting!

PREPARING YOUR SCALE

  1. Open the battery compartment on the scale underside.
  2. Remove isolating tab from beneath the battery.
  3. Close the battery compartment.
  4. Select kg, st or lb weight mode by the switch on the underside of the scale.
  5. Position scale on a firm flat surface.

INITIALIZING YOUR SCALE

*This initialization process must be repeated any time the scale is moved *
At all other times, step straight on the scale

  1. Press the platform center and remove your foot.
  2. “0.0” will be displayed.
  3. The scale will switch off and is now ready for use.

OPERATING YOUR SCALE

  1. Step on scale platform and stand very still while it computes your weight.
  2. Your weight will be displayed.
  3. Step off. Your weight will be displayed for a few seconds.
  4. The scale will switch off.

WARNING INDICATORS

Lo Replace battery.
—- Weight exceeds maximum capacity.

ADVICE FOR USE AND CARE

• Always weigh yourself on the same scale placed on the same floor surface. Do not compare weight reading from one scale to
another as some differences will exist due to manufacturing tolerances.
• Placing your scale on a hard, even floor will ensure the greatest accuracy and consistency.
• Weigh yourself at the same time each day, before meals and without footwear. First thing in the morning is a good time.
• Your scale rounds up or down to the nearest increment. If you weigh yourself twice and get two different readings, your
weight lies between the two.
• Clean your scale with a damp cloth. Do not use chemical cleaning agents.
• Do not allow your scale to become saturated with water as this can damage the electronics.
• Treat your scale with care – it is a precision instrument. Do not drop it or jump on it. It is not shock proof.

TROUBLESHOOTING GUIDE

If you experience any difficulty in the use of your scale:
• Check to make sure the battery is correctly fi ed.
• Check that you have selected your preference of kilograms, stones or pounds.
• Make sure the scale is on a flat, level floor and not touching against a wall.
• Repeat the ‘Initialization’ procedure every me the scale is moved.
• When you use the scale, if there is no display at all or if “Lo” is displayed – try a new battery.
• If “—-“ is displayed the scale has been overloaded.

CHANGING THE BATTERY

• When the symbol “Lo” appears, the battery needs to be replaced.
• Use ONLY the recommended 3.0 Volt DC bu on type battery or equivalent. CR2032 3.0 VDC
• Remove battery cover by pushing down on the tab and lighting the cover off the unit.
• Use your finger to push down and pull out the battery. Avoid using any sharp metal object as it can cause the supply
terminals to short-circuit.
• Clean the battery contacts and also those of the device prior to battery re-installation.
• Make sure that the new battery is inserted with the positive polarity up!
• Replace battery cover.
• Remove the battery if the scale will not be used for extended periods of me.
• Batteries contain substances that may be harmful to the environment and human health.

WARNING: Discard old battery y carefully, out of reach of young children. Swallowing the battery may be fatal. If the battery is swallowed, contact the hospital immediately to have it removed.

This symbol indicates that batteries should not be disposed of in the normal household waste but should be taken to an appropriate local recycling facility when one is available.
Never throw batteries in a fire or a empty to open outer casings, they may explode!

LIMITED WARRANTY

This electronic glass scale is guaranteed for one year from the date of purchase against manufacturer’s defect under normal, household use. Following the directions closely will ensure years of dependable opera on. If the scale does not function properly, first check the battery (see battery replacement instruction). Replace the battery if necessary.

FCC STATEMENT

NOTE: POTENTIAL FOE RADIO/TELEVISION INTERFERENCE (for U.S.A. Only)
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a par culartions installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Questions about your Manual ? Post in the comments!

Electronic Nasal Aspirator NS14 Instruction Manual

Electronic Nasal Aspirator NS14

Instruction Manual

Electronic Nasal Aspirator

Electronic Nasal Aspirator
Model : NS14

Manuctured for and Distributed by:
180° Innovations, Lakewood, CO 80215
Made in China

CONTENTS

Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product.

PRODUCT FEATURES

  1. Powerful Suction: Place aspiration tip into nostril to gently, yet powerfully remove nasal secretions.
  2. Safe: The soft aspiration tips are made from comfortable, latex-free, soft hygienic silicone to help prevent the possibility of injury when using the device. The tips are also dishwasher safe.
  3. Compact & Easy Design: This device is compact, easy to hold and operate and is safe and comfortable for use with infants or children.
  4. Washable Head Module Design: Tips, collection cup & removable head piece can be removed from the device and washed. (Collection cup can also be disinfected in boiling water.)
  5. Easy to Use: Simple operation.
  6. Battery Operated: This device uses two 1.5V AA batteries (included).

General Advice

The device is designed for using suction to remove nasal secretions and mucus in Children (age newborn to 12 years old) in your home environment.

  1. Do not expose the device to extreme temperature, very high humidity level, or direct sunlight.
  2. Avoid extreme shock, stress on or dropping of the device. It is not shock proof.
  3. Replace the batteries when the power and/or the sound of the pump weakens during the use of the device.
  4. It is recommended that you remove the batteries if the device will not be used for a period of time.
  5. Pressing and holding the power button starts the device and generates vacuum for the removal of nasal secretions and mucus. To stop the suction, simply release the power button to turn it off.
  6. Only a few seconds of suction at a time are necessary.
  7. This Nasal Aspirator is for cleaning/removal of nasal secretions only. Do not use this device other than for its intended purposes.
  8. During the use of the device, the baby/child should not hold their breath, close their mouth or swallow. This will help to avoid vacuum pressure resulting in an eardrum pressure imbalance.
  9. If the baby/child does not feel well when using the device, stop and consult a doctor immediately.
  10. Do not apply excessive force when placing the aspiration tip into the nasal cavity.
  11. This device is for home use only. Please consult a doctor in case of nasal diseases.
  12. The aspirator tips should be cleaned after each and every use.
  13. The operators of this device shall be adults or individuals who can follow the instructions and notices outlined in this user’s manual. This device is not intended for use by children themselves. Keep the nasal aspirator stored away from children. Children should NEVER operate the device themselves.

14. DO NOT use the Nasal Aspirator when the baby/child has the following contraindications:

  • Nasal bleeding
  • Acute head, facial, or neck injury
  • Coagulopathy or bleeding disorder

15 .Before using the device, please read this User’s Manual carefully. Incorrect use of the device may cause the following hazards/complications:

  • Mechanical trauma
  • Nasal irritation/bleeding
  • Mucosal hemorrhage
  • Discomfort and pain

NOTE: This Nasal Aspirator must only be used with the tips supplied with the device.

WARNINGS

Failure to follow these warnings and the assembly instructions could result in serious injury or death. Modifications not authorized by the manufacturer may void user’s authority to operate this device.

  • WARNING: This product is not a toy. Do not allow children to play with it. Individual parts may present a choking hazard.
  • Keep Nasal Aspirator away from heat sources, such as fireplaces, radiators, stoves, and TVs or other appliances. Heat can damage the case or electrical parts.
  • DO NOT use the Nasal Aspirator Unit if it has been dropped or is damaged.
  • DO NOT OPEN THE NASAL ASPIRATOR. There are NO user-serviceable parts inside the unit. Risk of electrical shock, fire or death.
  • Do not drop the device! Protect it from severe impact and shock. Keep out of the reach of children when not in use.
  • NOTE: Do not microwave.
  • CAUTION: Never insert the aspirator too far into the nostril. Never place the tip firmly against the inside wall of the nostril. This aspirator is for cleaning congestion in nasal passages.
  • Do not use this device for anything other than its intended purpose. Do not modify this device in any way.
  • NEVER use on ears, mouth, or eyes.
  • NOTE: Please consult with your physician on when and how often you should aspirate your baby/child’s nasal passages.

Product Overview

Product Overview

Battery Installation/Replacement

Recommended battery type – alkaline, size AA 1.5 VDC.
Change batteries when product ceases to operate satisfactorily.

  1. Loosen Battery Cover Screw and remove the battery cover as shown below.
  2. Requires two 1.5V alkaline AA size batteries (included).
  3. Clean the battery ends as well as the contacts in the device prior to installing or re-installing batteries (use a cotton swab slightly dampened with rubbing alcohol).
  4. Insert two new batteries being careful to match the correct polarities (+ and -).
  5. Firmly press the batteries to make sure they are completely inserted.
  6. Replace the battery cover making sure to insert Tab into Notch and then press until the cover clicks into place. Tighten the screw.
Battery Installation

Battery Safety

  • When changing the batteries, use batteries of the same type, make and capacity.
  • Always replace both batteries at the same time.
  • Never mix alkaline, standard carbon-zinc or rechargeable batteries in the same device. Do not mix old and new batteries.
  • Use batteries free of heavy metals.
  • Dispose of used batteries in accordance to your state and local regulations. Never dispose of batteries in the normal household waste.
  • Keep the batteries out of children’s reach.
  • Batteries may leak battery acid; 1. if mixed with a different battery type, if inserted incorrectly (put in backwards) or 2. if all batteries are not replaced or recharged at the same time.
  • Batteries may explode or leak battery acid if disposed of in fire or when charging a battery that is not specifically made to be recharged. Never recharge a cell of one type in a recharger made for a cell of another type.
  • Discard leaky batteries immediately. They can cause skin burns or other injury. When discarding batteries, be sure to dispose of them in the proper manner, according to your state and local regulations.
  • Always remove batteries before storing or if product will not be used for a prolonged period of time. Batteries left in the unit may leak and cause damage.

Instruction for Use

  1. There are two Tips to choose from. The large tip is recommended for use when the mucus is in a thicker, more solid form. The narrow tip is recommended for use when the mucus is loose and in a liquid form or when nostril opening is smaller.
Tip

2. Be sure to place the tip securely on the aspirator. The Tip must completely cover the rib before using.

cover the rib before using

3. Hold the baby/child upright and insert the tip into the nostril until the tip seals the nostril. Be careful not to place the tip too far into the nostril or press against the inside wall of the nostril.

4. Press and hold the power button to activate and allow the suction to clear the mucus. Only a few seconds of suction at a time are necessary. Repeat in the other nostril or as needed.

Press and hold the power
button

HELPFUL HINTS:

  • If needed, block the opposite nostril for more effective suctioning.
  • A small amount of saline mist may help to loosen thicker mucus.
  • Opening the baby/child’s mouth will help reduce ear pressure discomfort.

Note: The mucus may not immediately appear in the collection cup. After each use we recommend a quick cleaning of the used tip by removing it from the unit and thoroughly rinsing under warm tap.

Care and Cleaning

  1. Separate the suction portion from the base of the aspirator by gently pulling it apart.
  2. Unscrew collection cup by turning it counter clockwise.
  3. Remove white rubber ring located where collection cup screws in.
Care and Cleaning

4. Cleaning the Base: Wipe the unit with a clean soft dry cloth.

NEVER WASH THE BASE WITH WATER OR ANY LIQUID

NEVER WASH THE BASE WITH WATER OR ANY LIQUID

5. Cleaning the Suction Portion: Wash the collection cup, silicone ring and aspirator tips with mild soap and water and rinse thoroughly with running hot tap water for 3 minutes.

6. Rinse the Removable Head Piece with running hot tap water only for 3 minutes.

7. Let all pieces thoroughly air dry before re-assembling.

NOTES:

  • Never use any cleaners or solutions other than mild soap and water.
  • After cleaning, the collection cup and silicone ring may be disinfected by boiling in water.
  • NEVER boil the Removable Head Piece or the Non-return Tube. They may be damaged if overheated.
  • Nasal Tips ONLY are dishwasher safe.

Technical Specifications

Technical Specifications

EMC Tables

EMC Tables
EMC Tables
EMC Tables

Limited Warranty

This NS14 Nasal Aspirator (batteries excluded) is guaranteed for one year from the date of purchase against manufacturer’s defect under normal, household use and without evidence of tampering.

WARRANTY EXCLUSIONS: Device shows any signs of tampering or attempted modification. Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage. Damage caused by natural disasters (fire, flood, earthquake, lightening). No receipt or proof of purchase showing date of purchase.

Following the directions closely will ensure years of dependable operation. If the NS14 Nasal Aspirator does not function properly, first check the batteries (see battery installation/replacement instructions). Replace the batteries if necessary.

Questions about your Manual ? Post in the comments!

Infrared Ear Thermometer KI-8190 Instruction Manual

Infrared Ear Thermometer KI-8190

INSTRUCTION MANUAL

Infrared Ear Thermometer

Infrared Ear Thermometer
KI-8190

PRECAUTION:
1. Please consult your physician to verify your body temperature.
2. D0 NOT scrape or scratch the lens as it will hamper the effectiveness of the device.
3. The device is intended for consumer use only.
4. Calibration is recommended every two years.

POWER SOURCE SIZE AAA (1.5V) x 2
WARRANTY: LIMITED ONE YEAR FROM THE DATE OF PURCHASE

Parts Identification

Parts Identification

Why an IR ear thermometer?
The tympanic membrane (eardrum), and the hypothalamus, the part of the brain which controls body temperature, share a common blood supply so tympanic readings rise and fall rapidly with core temperature (deep body temperature). This makes the ear temperatures one of the best indicators of internal body (core) temperature.

What are normal temperature values?
Human body temperature varies from person to person, some run in the lower range (96-97°F) and some run in the higher range (98-99°F). Also, your normal body temperature changes throughout the day and can vary at different times of the year. It is very important to know your normal body temperature range. We recommend measuring yourself when healthy to establish reference temperatures. This will help you feel more confident of the measured temperature readings when ill.

Information You Should Know Before Operating the IR Ear Thermometer
How to correctly use the IR ear thermometer

  1. It is useful to try this thermometer on yourself first to become familiar with it’s operations.
  2. Do not take the temperature immediately upon waking. Sleeping on the ear can cause the temperature to be higher than normal.
  3. It is common for the readings to be slightly different between the right and left ear. We suggest using the same ear to obtain temperature readings.
  4. Straighten the ear canal for measuring:
    Children under 12 months: Straighten ear canal by gently pulling the ear back.
Ear Back

Children over 12 months and Adults: Straighten the ear canal by gently pulling the ear back and up.

Ear Back and Up

5. This IR ear thermometer automatically converts the measured ear temperature reading to oral temperature.

6. Make sure the ear canal is dry, clean and free of wax or particulates.

Batteries
INSTALLING/REPLACING THE BATTERY

  1. Pull the battery cover off in the direction shown.
  2. Prior to installing new batteries you rnust clean the metal contact ends of the batteries and the metal springs and contacts for the batteries in the battery compartment.
  3. Install 2 new “AAA” batteries into the battery compartment matching correct polarities.
  4. Replace the battery cover securely.

WARNING: Do not put used batteries in trash. Recycle or manage as hazardous waste. Never dispose of batteries in fire. Dispose in recycling trash only. Do not recharge, put in backwards or disassemble. This may cause explosion, leakage and injury.

CAUTION: When replacing batteries, do not mix old ones and new ones. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.

Batteries

How to Operate the Thermometer

  1. Press and release the Power button to turn o n the unit. (Figure 11 A beep is heard. After about 2 seconds, the display shows that the unit is ready for measurement. (Figure 2)
  2. Place the probe into the ear canal then press and release the Power Button again to start measuring.
  3. While it is measuring, the display will show an “arrow” sign. (Figure 3)
  4. 4. A”beep-beep”sound is heard when the measurement is completed. (Figure 41
  5. The temperature and back light color shows on the display. The back light color will light according to the reading:
How to Operate the Thermometer

6. If the temperature reading is above 99.5°F, eight consecutive beeps will be heard to indicate fever alarm.
7. After the happy face stops flashing, You can repeat measurement by pressing the Power button again.
8. T urn off the unit by pressing and holding the Power button for 3 seconds until the OFF message is displayed. Along beep is heard. (Figure 5)

How to Operate the Thermometer

For Centigrade and Fahrenheit Switchable Models:
The Centigrade or Fahrenheit mode can be switched by turning the unit on then pressing the POWER button again immediately and holding it down. The display will show ‘CH’ with “F. or”C”. Release the button when the mode you desire is in the display window. The unit will show “L” with the degree sign and the happy face symbol in the display and is ready to take a new temperature reading.

For Centigrade and Fahrenheit Switchable Models

OPERATIONAL HINTS:

  1. Between each measurement, please allow a 5-second interval in order to obtain the most accurate result.
  2. Ensure that the probe lens is clean before each measurement. Dirty probe lens may cause inaccurate measurement.
  3. Because the thermometer is a very sensitive device, it must be at room temperature (approx. 60.8 – 104.°F) for at least 30 minutes before using to avoid any incorrect measurements.

Warning:
Performance of the device may be degraded if the device is operated or stored outside the stated temperature and humidity range of if the patient’s temperature is below ambient (room) temperature.

Memory Mode

Memory Mode
Memory Mode

Cleaning and Care

Cleaning and Care
Cleaning and Care

Error Message

Error Message

Specification

Specification

Limited Warranty
This device (batteries excluded) is guaranteed for one year from the date of purchase against manufacturers defect under normal use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device Is not properly operated according to the instructions as described in this manual.
• Device shows any signs of tampering or attempted modification.
• Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage.
• Natural disasters (such as fire, flood, earthquake, lightening).
• Nornelptor proof of purchase showing dote of purchase

Following the instructions closely will ensure years of dependable operation.

Explanation of Symbol

FCC STATEMENT

NOTE POTENTIAL FOR FrADICITTELEVISION
INTERFERENCE (for USA Only)

Operation is subject to the fallowing two conditions 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and found . comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation. The product generates, uses, and can radials radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, Mere is no guarantee that in.rference will not occur in a particular instelatiorc If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on and off, the user is encouraged to try to correct ale interference by one or more of Me following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receives
• Consult the dealer or an experienced redid. technician for help.

Changes or modifications not expressly approved by the party responsible for compliance or could void the users authority to operate the equipment.

Questions about your Manual ? Post in the comments!

Infrared Ear Thermometer KI-8170L Instruction Manual

Infrared Ear Thermometer KI-8170L

Instruction Manual

Infrared Ear Thermometer KI-8170

Infrared Ear Thermometer
Model KI-8170L

Precautions

  1. Please consult your physician to verify your body temperature.
  2. DO NOT scrape or scratch the lens as it will hamper the effectiveness of the device.
  3. The device is intended for consumer-use only.
  4. Calibration is recommended every two years.
  5. Do not drop or expose thermometer to electric shock as this may adversely affect its performance

POWER SOURCE SIZE AAA (1.5V) x 2
WARRANTY: ONE YEAR FROM THE DATE OF PURCHASE

Parts Identification

Parts Identification

Why IR ear thermometer?
The tympanic membrane (eardrum), and the hypothalamus, the part of the brain which controls body temperature, share a common blood supply, so tympanic readings rise and fall rapidly with core temperature (deep-body temperature). This makes the ear temperatures one of the best indicators of internal body (core) temperature.

What are normal temperature values?
Human body temperature varies from person to person. One person’s body temperatures are different from time to time. Therefore, it is very important to know your normal body temperature range. Because of this, we recommend that you measure yourself when healthy to establish reference temperatures which will make you feel more confident of the measured temperature when ill.

Information You Should Know Before Operating the IR Ear Thermometer
How to use the IR ear thermometer correctly?
1. It is useful to try this thermometer on yourself first to become familiar with its operations.
2. Please do not take the temperature immediately after waking up. Sleeping on the ear may cause the temperature to be higher than normal.
3. It is common for the readings to be slightly different between the right and the left ear. Therefore, we suggest using the same ear to obtain temperature.
4. To make the ear canal straight for measurement:
For Children under 12 months: Make the ear canal straight by pulling the ear back.

Ear Back

For Children over 12 months and Adults: Make the ear canal straight by pulling the ear back and up.

Ear Back and Up

Preparation for Use
Installing/Replacing the Battery

  1. Pull the battery cover off in the direction shown.
  2. Clean the battery contacts and also those of the device prior to battery re-installation.
  3. Install two new “AAA” batteries into the battery compartment matching correct polarities.
    4.Replace and fasten the battery cover securely.

Warning:
Batteries contain mercury. Refer to your local disposal laws for proper disposition. Manage as hazardous waste. Do not recharge, put in backwards, disassemble or dispose of batteries in fire. This may cause explosion, leakage and injury.

Caution:
When replacing batteries, do not mix old ones and new ones. Do not mix alkaline, standard(carbon-zinc) or rechargeable(nickel-cadmium) batteries.

Replacing the Battery

How to Operate the Thermometer

  1. Press and release the START/STOP button to turn on the unit. (F igure 1 ) A beep is heard. After about 2 seconds, the display shows that the unit is ready for measurement. (F igure 2 )
  2. Place the probe into the ear canal then press and release the START/STOP button again to start measurement.
  3. While it is measuring, the display will show an “arrow” sign. (F ig u re 3 )
  4. A “beep-beep”sound is heard when the measurement is completed. (F ig u re 4 )
  5. The temperature and back light color shows on the display. The display will light up according to the reading.

Please refer to Table 1

Table 1

6. After the smiling face symbol stops flashing, you can repeat measurement by pressing the START/STOP button again.

7. Turn off the unit by pressing and holding the START/STOP button for 5 seconds until the OFF message is displayed. A long beep is heard. (F igure 5 )

START

For Fahrenheit and Centigrade Switchable Models:
The Centigrade or Fahrenheit mode can be switched by turning the unit on then pressing the START/STOP button again immediately and holding it down. The display will show “CH” with “F” or”C”. Release the button when the mode you desire is in the display window. The unit will show “L” with the degree sign and the smiling face symbol in the display and is ready to take a new temperature reading.

For Fahrenheit and Centigrade

IMPORTANT THINGS TO KNOW

• Allow at least 1-3 minutes between each measurement in order to obtain the most accurate result.
• Make sure the probe lens is clean and clear before use. It should be ‘mirror like’ or reflective. A dirty, blocked or scratched lens will cause incorrect results.
• Do not store the device in extreme conditions or temperatures (ie., direct sunlight, very hot/cold or high moisture like a bathroom). Unit is not waterproof.
• If it has been stored in extreme conditions, wait at least one hour for it to return to a normal room temperature before using.
• Wait at least thirty minutes after bathing, exercising or eating before taking a measurement.
• Do not dismantle or modify the device other than changing the batteries.
• This device has no user serviceable parts. Do not dismantle or modify other than changing the batteries.

WARNING:
Performance of the device may be degraded if it is operated or stored outside the stated temperature and humidity range or if the patient’s temperature is below the ambient (room) temperature.

Memory Mode

Memory Mode
Deleting Memories
Cleaning and Care

Error Message

Error Message

Specification

Specification

Limited Warranty
This device (batteries excluded) is guaranteed for one year from the date of purchase against manufacturer’s defect under normal use and without evidence of tampering.

WARRANTY EXCLUSIONS:
• Device is not properly operated according to the instructions as described in this manual.
• Device shows any signs of tampering or attempted modification.
▪ Evidence of improper handling or storing, such as dropping, heat, liquid or cleaner damage.
▪ Natural disasters (such as fire, flood, earthquake, lightening). No receipt or proof of purchase showing date of purchase

Following the instructions closely will ensure years of dependable operation.

FCC STATEMENT
NOTE:
POTENTIAL FOR RADIO/TELEVSION INTERFERENCE (for U.S.A. Only)

Operation is subject to the following two conditions 1)This device may not cause harmful Interference, and 2) this device must accept any interference received, including interference That may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television rception, which can be determined by turning the product on and off, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

Questions about your Manual ? Post in the comments!