Verizon FOIS Home Router User Manual

Verizon FOIS Home Router User Manual
Verizon FOIS Home Router User Manual

Model G3100

INTRODUCTION

1.0 Package Contents
1.1 System Requirements
1.2 Features
1.3 Getting to Know Your
Fios Home Router

The Verizon Fios Home Router lets you transmit and distribute digital entertainment and information to multiple devices in your home/office.


Your Fios Home Router supports networking using coaxial cables, Ethernet, or Wi-Fi, making it one of the most versatile and powerful routers available.

PACKA GE CONTENTS, SYSTEM REQUIREMENTS AND FEATURES

1.0/ PACKA GE CONTENTS
Your package contains:
• Fios Home Router
• Power adapter
• Ethernet cable, three meters (white)
• OSS (Open Source Software) insert guide

1.1/ SYSTEM REQUIREMENTS
System and software requirements are:
• A computer or other network device supporting Wi-Fi or wired Ethernet
• A web browser, such as Chrome™, Firefox®, Internet Explorer 8® or higher, or Safari® 5.1 or higher

1.2/ FEATURES
Your Fios Home Router features include:
• Support for multiple networking standards, including
–– WAN – Gigabit Ethernet and MoCA 1.1 interfaces
–– LAN – 802.11 b/g/n/ac/ax, Gigabit Ethernet and MoCA 2.5 interfaces
• Integrated wired networking with 4-port Ethernet switch and Coax (MoCA)

–– Ethernet supports speeds up to 1000 Mbps
–– MoCA 2.5 and 1.1 enabled to support speeds up to 700 Mbps over coaxial cable
• Integrated wireless networking with 802.11b/g/n/ac/ax access point featuring:
–– Enabled 802.11b capable speeds (based on device)
–– Enabled 802.11g capable speeds (based on device)
–– Enabled 802.11n capable speeds (based on device)
–– Enabled 802.11ac capable speeds (based on device)
–– Enabled 802.11ax capable speeds (based on device)
• Enterprise-level security, including:
–– Fully customizable firewall with Stateful Packet Inspection (SPI)
–– Content filtering with URL-keyword based filtering, parental controls, and customizable filtering policies per computer
–– Intrusion detection with Denial of Service protection against IP spoofing attacks, scanning attacks, IP fragment overlap exploit, ping of death, and fragmentation attacks
–– Event logging
–– MAC address filtering
–– Static NAT
–– Port forwarding
–– Port triggering

–– Access control
–– Advanced wireless protection featuring WPA2/WPA Mixed Mode and MAC address filtering
• Options, including:
–– DHCP server
–– WAN interface auto-detection
–– Dynamic DNS
–– DNS server
–– LAN IP and WAN IP address selection
–– MAC address cloning
–– IPv6 support
–– QoS support (end to end layer 2/3) featuring: Differentiated Services (Diffserv), 802.1p/q prioritization, and pass-through of WAN-side DSCPs, Per Hop Behaviors (PHBs), and
queuing to LAN-side devices
–– Remote management and secured remote management using HTTPS
–– Static routing
–– VPN (VPN pass through only)
–– IGMP
–– Daylight savings time support

1.3/ GETTING TO KNOW YOUR Fios Home Router
1.3a/ FRONT PANEL
The front panel’s unified button allows quick access to the Wi-Fi Protected Setup (WPS) feature and pairing mode.
The Router Status LED will be on white and solid when your router is turned on, connected to the internet, and functioning normally.

Router Status LED

FRONT PANEL
Router Status LED

The WPS button is used to initiate Wi-Fi Protected Setup. This is an easy way to add WPS capable devices to your wireless network. To activate the WPS function, press and hold the unified button located on the front of your Fios Home Router for more than two seconds. When WPS is initiated from your router, the Router Status
LED slowly flashes blue for up to two minutes, allowing time to complete the WPS pairing process on your wireless device (also known as a wireless client). When a device begins connecting to your router using WPS, the Router Status LED rapidly flashes blue for a few seconds, and turns solid blue and then solid white as the connection completes.
If there is an error during the WPS pairing process, the Router Status LED slowly flashes red for two minutes after the error occurs.
Refer to the “Connecting A Wi-Fi Device Using WPS” for more details. In addition, the unified button also provides a quick view of the operational state of the Fios Home Router using various colors as indicated in the chart above. Please refer to section 9.0h for details on the rear LEDs.

1.3b/ REAR PANEL
The rear panel of your router has a label that contains important information about your device, including the default settings for the router’s wireless network name (SSID), wireless password (WPA2 key), local URL for accessing the router’s administrative pages, and administrator password. The label also contains a QR code that you can scan with your smartphone, tablet, or other camera equipped Wi-Fi device to allow you to automatically connect your device to your Wi-Fi network without typing in a password (requires a QR code reading app with support for Wi-Fi QR codes).

The rear panel has seven ports; F-type coax, Ethernet LAN (four), Ethernet WAN, and USB. The rear panel also includes a DC power jack and a reset button.

Ethernet LAN – connects devices to your Fios Home Router using Ethernet cables to join the local area network (LAN). The four Ethernet LAN ports are 10/100/1000 Mbps auto-sensing and can be used with either straight-through or crossover Ethernet cables.
• USB – provides up to 1000 mA at 5 VDC for attached devices. For example, you could charge a cell phone. With a firmware upgrade, the USB host functionality may be available for other devices, such as external storage and cameras. Firmware updates are performed automatically by Verizon.
Ethernet WAN – connects your Fios Home Router to the internet using an Ethernet cable.
Coax WAN and LAN – connects your router to the internet and/ or to other MoCA devices using a coaxial cable.
Warning: The WAN coax port is intended for connection to Verizon Fios only. It must not be connected to any exterior or interior coaxial wires not designated for Verizon Fios.
Reset Button – allows you to reset your router to the factory default settings. To perform a soft reboot, press and hold the button for at least three seconds. To reset your router to the factory default settings, press and hold the button for at least ten seconds.
• Power – connects your Fios Home Router to an electrical wall outlet using the supplied power adapter.
Warning: The included power adapter is for home use only, supporting voltages from 105-125 voltage in AC. Do not use in environments with greater than 125 voltage in AC.

Questions about your Verizon FOIS Home Router User Manual? Post in the comments!
Download Verizon FOIS Home Router User Manual [PDF]

Prime Laser Light Projector Manual

Transmitter
TXCC17

Each Box Contains:

1 Laser Light Projector
1 Ground Stake
1 ground stake knob
1 Remote Control (3V CR2032 Battery Included)
2 Piece Indoor stand
1 Instruction Manual

Each Box Contains
Each Box Contains

Getting Started

Getting Started
Getting Started

Battery Replacement:
Required Tool:
Small Phillips Screwdriver (not included)

Tools

PROGRAMMING INSTRUCTIONS

Plug the laser into an outdoor rated GFCI receptacle.

NOTE: When you first plug in the laser
• The default settings are:
• Light Color: Red & Green Mode
• Timer: 6 hours
• The laser light color may be adjusted/set from the Power button on the laser housing.

The time setting may be changed by pressing Xthe X Xsbutton don dthed laser body

  1. The laser will automatically turn on at dusk each day and run for the time programmed. It may take up to 10 minutes before the laser reaches full brightness.
    a. IMPORTANT NOTE: Once you have plugged in the laser to start using it, do not unplug it until done using it in that location.
  2. There are 3 different color display options to choose from: RED & GREEN (default), GREEN ONLY or RED ONLY.
    a. RED & GREEN MODE i. As mentioned, when the laser is first plugged into an outlet, this is the default setting.
    ii. RED & GREEN Mode
    To manually select this mode, press the button on the base of the laser until the laser projects red & green light. The laser must run through a full timer cycle, (one night’s use) for the color mode you selected to be saved to repeat the next night. The color mode will automatically be saved even when the button on the remote control is used to manually turn off the laser.

b. GREEN MODE

i. To manually select this mode, press the button on the base of the laser until the laser projects green light. The laser must run through a full timer cycle, (one night’s use) for the color mode you selected to be saved to repeat the next night. The color mode will automatically be saved even when the button on the remote control is used to manually turn off the laser

i. To manually select this mode, press the button on the base of the laser until the laser projects green light. The laser must run through a full timer cycle, (one night’s use) for the color mode you selected to be saved to repeat the next night. The color mode will automatically be saved even when the button on the remote control is used to manually turn off the laser

c. RED MODE
i. To manually select this mode, press the button on the base of the laser until the laser projects red light. The laser must run through a full timer cycle, (one night’s use) for the color mode you selected to be saved to repeat the next night. The color mode will automatically be saved even when the button on the remote control is used to manually turn off the laser.

ci. POWER OFF

To turn off the laser using the remote control, press the button. The laser will automatically turn on again the next evening at dusk in the last color and timer modes. To turn off the laser manually, press the button until the laser turns OFF. The laser will automatically turn on again the next evening at dusk in the last color mode programmed.

WARNING
This product contains a built-in heater to protect the laser diodes (light source) from freezing. The heater must continue to receive power even when the light is turned off. Failure to maintain the electrical power to this product when temperatures drop below 32°F can cause permanent failure of the laser diodes.
It may take up to 10 minutes after the laser has been turned on for it to achieve full brightness.

c. To manually select the timer setting, press the
button on the base of the laser until the
indicator light next to the desired time setting is
illuminated.

  1. The laser projector can receive signals from the remote control up to 24.38m (80ft) away. The distance may vary depending on line of sight (such as sending the signal through a wall) between the laser and the remote control.
  2. To operate properly, and to prolong the life of your laser projector, the laser must not be disconnected from the power source even when it has been turned off, until you are ready to stop using it at the end of the event or season. Store it in a cool, dry place when not in use.

IMPORTANT NOTE: Be sure to read all of the safety information, cautions, helpful tips and trouble-shooting sections of this manual before using this laser projector.

TROUBLESHOOTING

Problem:
Laser Light Projector is too dim.
Possible Cause:
The outside temperature is too cold
Corrective Action:
Allow the Laser Light Projector up to 10 minutes to brighten to full intensity.
Problem:
Laser Light Projector does not turn on at all.
Possible Causes:
• The outside temperature is too cold.
• The outlet the unit is plugged into is not working.

Corrective Action:
• Occasionally, if it is very cold, the Laser Light Projector
will appear to be off for a few minutes before slowly
turning on. Allow the Laser Light Projector up to 10
minutes to warm up to operating temperature.
• Check outlet to ensure flow of electricity:

  1. If plugged directly into a GFCI receptacle, press the “reset” button. If there is no “reset” button on the outlet but a sticker stating that it is GFCI protected, find the nearest GFCI receptacle in the house or in another area outside and press the “reset” button to ensure that it is activated so power may flow to the outlet where the Laser Light Projector is getting its power.
  2. Check the circuit breaker in the main electrical panel to ensure that the breaker is set and has not been tripped. If it has tripped, unplug the Laser Light Projector then reset the breaker before trying again.

Problem:
The remote control doesn’t work

Possible Cause:
• The remote control is not synced to the laser projector.
• The distance between the remote control and the laser is too far or the view is impeded.
• Battery is weak or spent.
Corrective Action:
• Move closer to the laser when using the remote control. The range and response will be impeded if the signal is going through solid objects like walls, doors, trees or heavy furniture.
• Replace the battery in the remote control with a new 3V CR2032 battery. Follow the steps outlined in step 6 of the set-up instructions.

To sync the remote control to the laser:
a. Turn OFF and unplug the laser from its power source. Remove the battery from the battery compartment by following the instructions outlined in step 6 of the set-up instructions in this manual. Press any button on the remote twice to discharge the battery.
b. Plug the laser back to its power source. Place the battery into the battery compartment following the instructions outlined in tstep 6 of the set-up instructions of this manual. Press any button on the remote. This will automatically begin syncing the remote to the laser. The blue LED on the remote will blink continuously while syncing. The remote will be synced and ready for use when the LED on the remote stops blinking.
c. If you cannot sync the remote control after following the steps above, contact Prime’s customer service at (888) 445-9955, toll-free between 8:00AM and 4:00PM Pacific Time Zone.

HELPFUL TIPS

• The Laser Light Projector safely operates in temperatures from -26°C up to 32°C (-15°F up to 90°F). It has a built-in heater and fan to help it maintain an optimal operating temperature. For these features to work properly, the Laser Light Projector must be plugged in at all times. In temperatures below 13°C (55°F) please allow up to 10 minutes for the laser to achieve full brightness.
• Do not at any time shine the Laser Light Projector directly into anyone’s eyes or your own.
• Do not place the laser in such a position that it will shine into cars or low flying aircraft.
• Do not place the laser in shaded areas away from direct sunlight. In order for the photosensor feature to work, the laser must detect sunlight and dusk to automatically turn on each day.

BATTERY INFORMATION

WARNING: This product contains a button cell battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately.
Batteries may explode or leak, and cause burns or injury if disposed in fire, mixed with a different battery type, inserted backwards, or disassembled.
Check with your local solid waste authority or recycling center for detailed information for proper button cell battery disposal.

The remote control included with this laser light projector
requires a 3V CR2032 button cell battery. To replace spent batteries, use a Phillips screwdriver to unscrew the battery compartment cover on the backside of the remote control.
The screw loosens when turning it counterclockwise (Fig. 5). To open the plastic battery compartment cover, twist the battery compartment cover counterclockwise with a coin or other flat tool, aligning the arrow on the cover to the UNLOCKED symbol (Fig. 6). Remove the plastic cover over the button cell battery. Make sure the negative side (-) of the battery faces inward and the positive side (+) faces outward (Fig. 7). Align the arrow on the cover with the UNLOCKED symbol on the outside of the remote control.
Twist the battery compartment cover to the right with a coin or other flat tool to align the arrow with the LOCKED symbol. Place the screw back into the designated compartment. Use the Phillips screwdriver, and twist clockwise to close the battery compartment (Fig. 8).


compartment cover on the backside of the remote control.
The screw loosens when turning it counterclockwise (Fig. 5). To open the plastic battery compartment cover, twist the battery compartment cover counterclockwise with a coin or other flat tool, aligning the arrow on the cover to the UNLOCKED symbol (Fig. 6). Remove the plastic cover over the button cell battery. Make sure the negative side (-) of the battery faces inward and the positive side (+) faces outward (Fig. 7). Align the arrow on the cover with the UNLOCKED symbol on the outside of the remote control.
Twist the battery compartment cover to the right with a coin or other flat tool to align the arrow with the LOCKED symbol. Place the screw back into the designated compartment. Use the Phillips screwdriver, and twist clockwise to close the battery compartment (Fig. 8).

SAFETY INFORMATION

This device is for use with a 110 – 125VAC power source.
120V AC/60 Hz
• Do not use with an external remote control, timer or light switch, as the laser contains a heating element for operation in low temperatures that needs power at all times.
• Do not connect your Laser Light Projector to a dimmer at any time as this may damage the laser itself.
• At no point should you shine the laser directly into anyone’s eyes.
• When operating this device in unsupervised, accessible areas, it is recommended that up-close access to the Laser Light Projector is restricted or prevented.
• Do not stare into the laser light source.
• Do not shine the laser into any moving vehicles or low flying aircraft.
• Do not attempt to disassemble the Laser Light Projector as there are no user-erviceable components.• Unplug and store in a cool dry place when not in use.
• Read and follow all instructions on the product and/or operating instructions provided with the product.
• Before using or reusing, inspect the product carefully.
Do not use the Laser Light Projector if there are any cracks in the lens or the housing, cuts or frayed areas in the power supply cord or connection of the cord to the plug, broken plug blades or any other damage that could be deemed a safety hazard.
• Do not directly cover the Laser Light Projector while in use (such as cloth, paper or any material not part of the product that would prevent heat dissipation or be a fire hazard).
• Do not hang ornaments or other objects from the cord or the Laser Light Projector.
• Do not mount or place near gas or electric heaters, fireplaces, candles or other similar heat sources.
• Keep away from children and pets.

WARNING: CHOKING HAZARD
The components packaged with the laser light projector contain small parts.
Keep out of reach of children.

CAUTION
Use of this product other than specified in the instruction manual or on the box may cause harm to yourself or others and may result in unfavorable results when using your Laser Light Projector.
This laser projector is certified as a class 3R/llla laser product to the requirements of the US Federal Laser Product Performance Standard (FLPPS) contained in the regulations in 21 CFR Subchapter J. Class 3R/llla laser products can be hazardous when directly viewed.
Avoid direct viewing of Class 3R/llla laser energy. For reference, the FLPPS requirements for demonstration laser products like laser pointers are limited to Class 3R/llla levels of laser energy. This product uses diffractive optics to scatter the beam energy. This scattering effect causes the energy concentration to drop below the exposure limits for momentary or accidental viewing at a relatively short distance from the laser aperture. As similar with all bright light sources, when operating this device in unsupervised general public areas, it is recommended that up close access to the Laser Light Projector be restricted or prevented.
This laser display device incorporates a Class 3R/llla laser system which, by itself, may be hazardous. However, this laser display device incorporates a protective housing and diffractive holographic optics in the machine design to prevent exposure or human access to laser radiation during operation or maintenance above the Class 3R/llla limits. Each individual laser beam power is under 1mW which is less than a standard laser pointer.
UNDER NO CIRCUMSTANCE shall attempts be made to open protective housing or operate the device if the aperture windows are damaged. Opening the Laser light Projector housing voids any safety agency certifications (cETLus, FCC, FDA

LASER SAFETY INITIATIVE
Aiming a laser at an aircraft is a serious safety risk and violates federal law. Lasers can cause temporary visual impairment for pilots who are trying to fly safely to their destinations and may be carrying hundreds of passengers. The FAA and Transport Canada are working with federal, state, and local law enforcement agencies to pursue civil and criminal penalties against individuals who purposely aim a laser at an aircraft.

FCC REGULATORY STATEMENT
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
    Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  2. Reorient or relocate the receiving antenna.
  3. Increase the separation between the equipment and receiver.
  4. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  5. Consult the dealer or an experienced radio/TV technician for help.

IC REGULATORY STATEMENT
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CAUTION / ATTENTION / PRECAUTION

LASER RADIATION. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS. LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.


RAYONNEMENT LASER NE PAS FIXER LE FAISCEAU NI REGARDER DIRECTEMENT
AVEC DES INSTRUMENTS OPTIQUES RAYONNEMENT LASER EN CAS
D’OUVERTURE ET DE DISPOSITIF DE VERROUILLAGE DÉFAIT.
RADIACIÓN LÁSER. NO MIRE FIJAMENTE EL HAZ NI LO OBSERVE DIRECTAMENTE CON INSTRUMENTOS ÓPTICOS. RADIACIÓN LÁSER CUANDO ESTÁ ABIERTO Y EL INTERBLOQUEO ESTÁ DESACTIVADO.


532-635nm Max Output <3mW CLASS IIIa LASER PRODUCT This product complies with 21 CFR 1040.10 and 1040.11 Sortie max. 532-635nm <3mW PRODUIT LASER CLASSE IIIa Ce produit est conforme au 21 CFR 1040.10 et 1040.11 Salida máx. de <3mW a 532-635 nm PRODUCTO LÁSER CLASE IIIa. Este producto cumple con 21 CFR 1040.10 y 1040.11

Questions about your Prime Laser Light Projector Manual? Post in the comments!

Proscan Smart Watch User Manual PBTW360

PROSCAN PBTW360
SMART WATCH
USE MANUAL

Please read the manual before use

1. SAFETY WARNING
 Before use, please read the user manual carefully.
 Only support the standard battery, charger and accessories we approved, we won’t take any responsibility for any consequences caused by the use of third party accessories.
 Prohibit the unauthorized dis-assembly of watch phone.
 No mechanical vibrating and shaking. No kicking the screen by tool.
 No using solute to clean the shell, such as benzene, thinner or alcohol. No touching the watch phone with corrosive chemicals and so on, but with a clean textile to clean it softly.
 No exposing the watch phone under the sunrise or the place with smog and dust.
 Keep the phone in dry. No using in the wet environment such as bathroom. This watch is not water proof and is strictly prohibited to rain and moisture.
 Please put the watch phone in a safety place out of the reach of children to avoid any dangerous happening. The information in this document won’t be modified or extended in accordance with any notice.
 The watch should be charging 2 hours at least before use.

2. PRODUCT DETAILS

2.1 Product details

Product Details
Product Details

Power button: Power on / off by long press the button, Awaken / turn off the screen, Back to main menu by short press.
USB port: Charging
Touch screen: each function (main menu) will be shown and displayed.

2.2 Products quick into
You can enter into next page by sliding screen to the left, and return to last page by sliding screen right, enter into the notice board after sliding from up to down, and return to main mean from down to up. It will be in mistake for a click if the drag distance too short.

2.3 Clock Display

Clock Display

Setting Method:
Power on, when the phone in clock mode, please click middle screen to choose the desired clock interfaces.

3. PRODUCT QUICK USE
3.1 Download the sync software

Scan below QR code to download the APP(only for android phone).

If you downloaded thesoftware before, please check if the version is the newest one to ensure all function normal use. And please update the software when have new version.

3.2 Install and use the sync software

Android Application installation:
Please install the android application in your smart phone. You can storage it into your phone memory or install by Sync assistant.

Android applications usage(already installed):
(Smart phone) Setting – Accessibility – Enter into Bluetooth notice (service), enabled this service, (please choose “sure” when shown a warning notices) the application runs on the background automatically.

Click the Bluetooth notice and choose the Notification service, select your Personal or System application in Notify application. Telephone service in including SMS, incoming call and seek watch.

Notice:
Please don’t shut the Bluetooth notify service when you are clearing software by background or close background application software. It will affect the Sync function between watch and phone if shut it.

3.3 Bluetooth connectivity and sync function

3.3.1 From phone to Watch
Phone settings – turn on bluetooth – search for devices, please click pair devices when found the watch, and also choose “yes” in your mobile phone, paired done.( The Bluetooth device name is PROSCAN-PBTW360)


Please choose “sure” when there is phone book request, meanwhile you’d better to choose “no remind again”, this is convenience when you connect next time (without remind again).

3.3.2 From watch to phone
BT Dialer-Search new device-found your smart watch (such as s9500)-connect.
Note:the mobile phone need to turn on the Bluetooth and allow to be searched by around Bluetooth products.

3.4 Basic Functions
 Message: Sync phones or watch message.
 Bluetooth: Set the Bluetooth, turn on / off.
 Call logs: You can check your phone call records after you connect with the Bluetooth. Shown all records including miss call, dialed calls and receive call. You can check the date, time and phone number of the miss call after you choose it, but only can call this number.
 Remote Notifier: When there is SMS, incoming messages from QQ and other applications on the connected phone, the watch phone will alert you to read them.
 Remote capture: Use phone camera take pictures; but remote by watch. Its need switch on the camera of phone in advance.
 Anti lost: Watch seek phone, or phone seek watch.
 Setting: Notice-sets clocks display and theme in phone setting; In the security Settings, the safe code Is 1122
 Pedometer: It can be adopted as a tool to avoid insufficient or excessive exercise by measuring calories of calories consumption based on collected data, such as number of steps, distance, speed, time, etc to control exercise. If you want return to main menu but keep pedometer during the exercise, please press the power button.
 Sleep Monitoring: Show your sleep quality base on your sleep times.
 Sedentary Remind: You can set a time to remind you up to do some exercise, we suggest you this time could be one hours.
 Quick response: It can download sync software when scan the quick response, if there Is a new version need to update, please contact with our servicer, our company will provide a new link for your download.
Audio Player: Can play music from local or smart phone after connected with Bluetooth.
 Browser: Browser need your phone has SIM card and surf the Internet.
 You can also have Alarm/Calendar/Calculator/Profiles/File Manager/Camera/Image viewer/Sounder recorder functions.

NOTICE
 Full charge before use, the charge time need 1-2 hours.
 Bluetooth will disconnect when exceed the distance (up to 10 meters), after switch on the Anti lost, the smart search function can’t be use before reconnect with Bluetooth.

NOTE: The effectiveness of all functions can be affected by the level of battery charge.

5. COMMON TROUBLE SHOOTING

Please refer below key functions for any problems with the watch.

 Unable to switch on: The time of press the power button too short, please keep it more than 3 seconds. Low power, please charge it.
 Shut down automatic: Low Power, please charge the watch.
 Using time too short: Battery Is not full, please make sure it Is full power (full charge need 2 hours at least). During the use of SIM card, the power will be run off soon if the signal too poor.
 Unable to charge: The battery’s life will be reduce after few years, please check if the battery are work. Change a new charger if it Is unworkable. Please check the USB slot connecting good, If no, please try again.
 Not caller’s name when incoming call: Forgot to choose upload the phone book when connected with BT, or unselected keep upload the phone book. Forgot to sync the
phone book when reconnected, please pair the device and connect BT again.
 Bad phone call voice: Watch and phone are separated too far, please be more close; Bad signal of BT. Bad signal of your own phone call place, please change a more better place for phone call.

6. MAIN FEATURES
 CPU: MTK6261D, 108 Mhz.
 Mobile phone 2G GSM 850/900/1800/1900
 Capacitive touch screen 1.54” 240*240 Pixs.
 Bluetooth 2.1.
 RAM/ROM:32MB/32MB.
 Support TF card (up to 32 GB)
 0.08 MPX camera.
 Battery 380 MAh Li-Battery.
 Micro SIM card slot.
 Speaker, microphone, multi languages.

Federal Communications Commission (FCC)

Interference Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

Note: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This mobile device meets guidelines for exposure to radio waves. Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines.

The SAR limit adopted by USA and Canada is 1.6 watts/kilogram (W/kg) averaged over one gram of tissue. The highest SAR value reported to the Federal Communications
Commission (FCC) and the Industry Canada (IC) for this device type when it is tested for use at the mouth is 0.045 W/kg, and that when it is properly worn on the wrist-worn is 1.003 W/kg.

The device complies with the RF specifications when the device is used near your ear or at a distance of 1.0 cm from your mouth. Ensure that the device accessories such as a device case and a device holster are not composed of metal components. Keep your device 0 cm away from your wrist-worn to meet the requirement earlier mentioned.

Questions about your Proscan Smart Watch User Manual PBTW360? Post in the comments!

Sabbat X12 Bluetooth Headphones User Manual

Sabbat
Sabbat X12 Bluetooth Headphones

Instructions
Sabbat

Manufacture: Shenzhen Sabbat
Technology Development Co. LTD

Product Schematic Diagram

Product Schematic Diagram
Product Schematic Diagram

Package list
• Bluesooth headset ( 2PCS )
• Power storage room
• USB charging line
• Instruction
• Exquisite packaging
• Product qualification certificate

Wearing a Sketch

Wearing  a  Sketch

Product specification
• Name: Sabbat Music wireless Bluetooth headset
• Bluetooth name: Sabbat X12
• Version: 4.1+EDR
• Input: DC 5V
• Battery Capacity: 3.7V/60mAh
• Talking Time: About 2-3 Hours
• Charging Time): About 60 Min
• Rechargeable warehouse: 3.7V / 750mAh
• Profile Support: 115P/HFP/A2DP/AVACP
• Sensitivity: 120 ± 5dB
• Frequency Response: 20-20000Hz
• Impedance: 320

Products use
Bluetooth pairing

1. Press and hold the power button on the earphones for 5-10 seconds until red and blue lights flash at she same.
2. Double—click any headset (host) power button, red and blue lights alternately flash, waiting for the left and right headphones automatically pair.
3. The earphones connect successfully with your phone when only blue lights showing on the earphones.

Sabbat X12 wirless earphones charging instructions :
1. Firstly charge the charging cabin: connect the cabin with the power adapter through the charging cable that enclosed with the earphones. When the cabin is fully charged LED lights will stay red.
2. Secondly charge the earphones through cabin: put the earphones inside the cabin correctly, when the earphones are under charging both LED lights on the cabin and earphones will flash red. When the earphones are fully charged, LED lights on the earphones will tum blue and stay for 5 seconds and LED lights on the cabin will turn off 10 seconds later.

Bluetooth link Turn on the phones Bluetooth search scan to ” Sabbat X12 ” and click connect

  • The earphones will automatically connect with same phone the next time you turn on Bluetooth on the phone.
  • If you want to connect the earphones with another phone, please follow up the above steps.
Bluetooth Setting

1. Listen to the music
* When headphones boot and and mobile phone connection, can use mobile phones to listen to music.
* Press the open key in the process of music, music on hold. Press will continue to play the music again.
* Music played in the process, double click to open the key, will play the neat song music.

2. Call
* When the headphones on and connected to the phone, can answer the call. Pick up the phone and only one headset week.
* When calls, voice telephone number. click having calls prompt headphones for the key, can answer the phone, if long according to decline a cal
* Phone in the process, press the open key, will hang up the phone, to go back to the previous state.
*Phone in the process, the volume can be adjusted through the phone call.

3. OFF
* Long press the headset key 5 seconds, the LED display normally on a red light, then turn it off.
* When about headphones matching use, only need to due to nun it off with one of the headphones, another headset will automatically shut down.

Matters needing attention
1. The headset should be stored in a dry and ventilated environment, to avoid oil, water, steam, moisture and dust, such as contact, lest affect product performance.
2. Avoid using stimulus, organic solvents or items containing these ingredients, dean the headphones.
3. The use of headphones should be correctly according to the requirement specification, pay attention to use the influence of environment on the headphones. In order to ensure the smooth connection it is recommended that the distance between the phone and headset within 10 meters.
4. Connect the headphones have not or poor communications, and other problems, please do not remove the headset secretly ontology and its accessories, otherwise no warranty.
5. Recharge headphones, please choose the standard USB charging lite or the company specified in conformity with the requirements of charging cable.
6. To ensure that your normal use headphones, please make sure that the headset battery is enough.

Product Warranty Card

Warranty Description

Thank you for purchasing “Sabbat” brand products in order to ensure that the legitimate lights and interests of you, please be informed that to mad the following items:
• This card warranty certificate foe the product, the product need for maintenance, please be sure to provide this ..rd. together with the products our company after-sales.
• When this card is only effective use for warranty within the scope of the products, see below:
1. Through legal, formal channels for the company’s products,
2. The non-artificial damage products, including but not limited to remove secretly, improper use, manual disasters and other circumstances not within the scope of the warranty:
3. Does not exceed the product warranty:-
• Low considerations include and not limited to above.
• When the company reserves the final interpretation.

Questions about your Sabbat X12 Bluetooth Headphones User Manual? Post in the comments!

…….

Skytech Fireplace Remote User Manual

SKY-4001
INSTALLATION AND OPERATING INSTRUCTIONS

INTRODUCTION
SKYTECH’S remote control system was developed to provide a safe, reliable and user-friendly remote control system for gas heating appliances. Its battery operation allows the system to operate independently of household current. The system operates on radio frequencies with non- directional signals. The SYSTEM’s operating range is approximately 20 feet. The system operates on one of 255 security codes programmed at the factory

COMPONENTS
WARNING

THE SKYTECH SKY-4001 MUST BE INSTALLED EXACTLY AS OUTLINED IN THESE INSTRUCTIONS. FOLLOW INSTRUCTIONS CAREFULLY DURING INSTALLATION. ANY MODIFICATION OF THE SKYTECH SKY -4001 OR ANY OF ITS COMPONENTS WILL VOID THE WARRANTY AND MAY POSE A FIRE HAZARD.

TRANSMITTER

TRANSMITTER
TRANSMITTER

The transmitter operates on a 3v battery (included) made specifically for remote controls and electronic lighters. Before using the transmitter, remove the insulation tab
protecting one end of the battery in the battery compartment.

The transmitter has ON and OFF functions that are activated by pressing either button on the face of the transmitter. When a button on the transmitter is pressed, a signal light on the transmitter illuminates briefly to verify that a signal has been sent. Upon initial use, there may be a delay of five seconds before the remote receiver will respond to the transmitter. This is part of the system’s design. If the signal light does not illuminate, check the position of the transmitter’s battery

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help

FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Important Note:

FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Questions about your Skytech Fireplace Remote User Manual? Post in the comments!

.

Peace Target Bluetooth Speaker User Manual 022-001

Manual for BT speaker

Small, compact size gives your audio powerful sound. The clear sound is powered by new generation amplifiers, that you can take with your enjoy anywhere.

FEATURES:
1.Portable speaker for your smart phone, tablet, laptop, or MP3 Player.
2.Light-weight, small in size, but incredible sound.
3.Plastic housing provides protection and great sound.
4.Up to 2-3 hours playback time, one a full charge

COMPONENTS INCLUDED
1.Mini speaker
2.Audio cable
3.Micro USB charging cable
4.User Manual

SPECIFICATIONS:
Power supplier: DC5V
Output power: 3W(1KHz,THD10%)
Frequency: 200Hz – 20KHZ
Signal&noise ratio:≥ 85dB
Impedance: 4 OHM(Ω)
Li-ion Output: 3.7V~4.2V+0.05V
Li-ion Input: 5V Lithium battery
capacity: 300mAh
Speaker Unit: 40mm

Button Description:

Long press for volume decrease

Long press for volume decrease; short press for last song.

answer / off the phone

Short press for pause or answer / off the phone.

Long press for volume increase; short press for next song.

Long press for volume increase; short press for next song.

Long press for switch on/off.

Long press for switch on/off.

hort press for radio /bluetooth play/line in model change

hort press for radio /bluetooth play/line in model change

hort press for radio /bluetooth play/line in model change

hort press for radio /bluetooth play/line in model change

Under BT Model:
Long press

hort press for radio /bluetooth play/line in model change

to turn on, at the same time, the blue light flashes. Search name of the speaker is “BT Speaker” Make your device and speaker bluetooth pairing. After a successful connection, light slow flash, sound will be issued “dong dong dong” tones

Under Line-in Model:

AUX audio playback: appendix provides the 3.5mm audio line.Can play music by link to mobile phone、MP3、MP4、PC、IPOD and other audio devices. Reminder: When it’s on AUX model, above buttons keeps on the same function.

Under radio Model:

Under radio Model

The interface description:

The interface description:

SAFETY CAUTIONS:

1.Please read the instructions carefully before using.
2.Avoid contact with liquids; keep away from water, and high moisture conditions.
3.Do not locate the speaker or cord near heat sources such as radiators, heaters, air ducts. or
direct sunlight.
4.Do not place a naked flame source such as candles on the Mini Speaker.
5.Recharge the battery with suitable voltage output(5V/500mA)
6.Do not hit the product severely, or insert any conductive objects into the speaker, or charging
jack.
7.Do not block the speaker grill when the speaker is running.
8.Stop using at once if high temperature, smoke, burning smell, nor-normal noise, or fire are
noticed coming from product.
9.Do not repair on your own, seek the help of a professional.
10.To avoid getting shocked, do not touch product with wet hands.
11.Keep out of reach of children.

TROUBLESHOOTING
No Sound
1.Audio cable is not fully plugged into the 3.5mm audio port on speaker or device.
2.Audio cable is damaged.
3.Source of audio is not working.
4.No LED indication when audio cable is plugged-in.
5.Mini speaker is out power.

Not charging:
1.Input power source is not normal(5V/500mA)
2.Micro USB adaptor of charging cable is not fully plugged into the mini speaker charging port.
3.Charging cable is damaged.

Questions about your Peace Target Bluetooth Speaker User Manual 022-001? Post in the comments!