Jabra freeway manual

Jabra freeway

Jabra freeway manual

ABOUT YOUR JABRA FREEWAY
A Answer/end button
Tap to answer/end call
B FM button
Tap to activate FM mode and stream music and calls to your car radio
C Volume down
Tap to adjust volume down
D Mute button
Tap to mute/un-mute your microphone during a call
E Volume up
Tap to adjust volume up
F Voice button
Tap to initiate voice command functions
G Visor clip
H Power switch
Slide to ON position to turn the FREEWAY on
I Micro USB charging connector
Charge with the Micro USB charger
J Charging indicator light
Light red while charging and turns off when fully charged

JABRA FREEWAY Front view

JABRA FREEWAY Side View

WHAT YOUR SPEAKERPHONE CAN DO
Your Jabra FREEWAY lets you do all this:
– Make and answer calls just using your voice
– Ease of use with Jabra Voice Guidance
– Last number redialing and call back last number
– Voice dialing*
– Three way calling*
– Advanced MultiUse™ – be connected to two active Bluetooth devices at the same time
– Tells you who is calling*
– Transfer music and calls to your car radio
– Turns on and off automatically using the builtin G-sensor
– Listen to wireless stereo music in Virtual Surround Sound*

Specifications:
– Up to 14 hours of talk time and 40 days of standby time
– Rich and crisp stereo sound and Virtual Surround Sound
– Dual microphones provides outstanding background noise reduction
– Digital sound enhancements via DSP technology
– Clear wireless streaming of you r favorite multimedia: Music, podcasts, video, etc. (from A2DP enabled devices*)
– Bluetooth technology – Easy pairing with Bluetooth 2.1 + EDR & eSCO
– Supported Bluetooth profiles: HFP, HSP, A2DP, AVRCP, PBAP
– Up to 128-bit encryption
– Rechargeable battery with charging option from car charger or PC using the supplied USB cable
– Operating range up to 10 meters (approximately)
– Weight 150 grams
– Size: L 100 mm x W 120 mm x H 20 mm

GETTING STARTED
You should follow three steps before using your speakerphone:
1 Charge your Speakerphone using the supplied USB cable and car charger (approximately 2 hours)
2 Activate Bluetooth® on your phone or device (refer to the manual of your device)
3 Pair your speakerphone to your phone or device
The first time you turn your Jabra FREEWAY on you will hear Voice Guidance telling you what to do.

NOTE: Voice Guidance and Voice commands are enabled as the default setting when you turn on your Jabra FREEWAY the first time. You can at any time disable both by pressing the Voice button while you slide the power switch into the On position. You will hear ”Voice off” and FREEWAY will no longer talk to you or listen for commands. Repeat the process to enable the voice features again.

CHARGE YOUR SPEAKERPHONE
Make sure that your speakerphone is fully charged before you start using it. Use the USB cable to connect Jabra FREEWAY to the car charger. Plug the car charger into your car’s power outlet. The charging indicator light will light up in red while charging. When the Jabra FREEWAY is fully charged the indicator light will turn off.
A full charge takes approximately two hours.

Jabra FREEWAY can be charged outside your car using the USB cable.

CHARGE YOUR SPEAKERPHONE

Only use the charger provided in the box – do not use chargers from other devices as this may damage your speakerphone. Also you should not use your supplied FREEWAY charger to charge other devices.

NOTE: The lifetime of the battery will be significantly reduced if your device is left uncharged for a long period. We therefore recommend that you recharge your device at least once a month.
TURNING YOUR SPEAKERPHONE ON AND OFF
– Slide the On/Off power switch to turn the speakerphone on or off.
– If the switch is left in the On position the Jabra FREEWAY will automatically turn on and reconnect to your phone when you enter your car (open the car door).

TURNING YOUR SPEAKERPHONE

The Jabra FREEWAY will automatically turn off when your phone is moved away from the car.

NOTE: Moving the Jabra FREEWAY will also turn it on if the power switch is in the On position.

PAIRING IT WITH YOUR PHONE/DEVICE
Speakerphones are connected to mobile phones using a procedure
called ‘pairing’. By following a few simple steps, a phone can be
paired with a speakerphone in a matter of seconds.
1 Activate Bluetooth® on your phone/device
2 Turn the Jabra FREEWAY on
3 The first time you turn the FREEWAY on it will automatically enter into pairing mode. The Answer/end button will flash with a blue light and you will be voice guided through the pairing process. If you have disabled voice guidance go to the Bluetooth® settings menu on your phone/device and search for new Bluetooth® devices. Choose Jabra FREEWAY.
4 When pairing is complete you will hear ”Connected”. You are now ready to start using your Jabra FREEWAY.

NOTE: If asked for a passkey or pin code use 0000 (four zeros)
passkey
Pin code

PAIR A NEW OR SECOND DEVICE
1 Ensure that the Jabra FREEWAY is turned on
2 Tap the Voice button. You will be asked to ”Say a command”
3 Say ”Pair new device” and follow the instructions
4 If this is your second device you will need to reconnect to the first device afterwards

NOTE: If you have disabled Voice Guidance you can put Jabra FREEWAY in pairing mode manually by pressing and holding the Answer/end button while you slide the power switch into the On position. The Answer/end button will flash blue to indicate that you are in pairing mode.

CONNECTING WITH YOUR PHONE
Pairing is only needed the first time a speakerphone and a phone/ device are used together. When the speakerphone and phone/ device have been paired once they will automatically reconnect when the speakerphone is on and Bluetooth® is activated on the phone/device.

If the devices are paired, but do not immediately reconnect tap the Answer/end button.

PLACE THE SPEAKERPHONE IN YOUR VEHICLE
The Jabra FREEWAY sits discreetly and conveniently on the sun visor using the attached clip. For optimal sound quality place the Jabra FREEWAY right in front of you and speak directly into the speakerphone.

PLACE THE SPEAKERPHONE

HOW TO
The Jabra FREEWAY is easy to operate. The buttons performs different functions depending on how long you press them.

Instruction

Answer a call
– Tap the Answer/End button
– Say “Answer” after the caller is announced.*

End a call
– Tap the Answer/End button

Reject/ignore a call*
– Double Tab the Answer/End button when the phone rings to reject an incoming call. Depending on your phone settings, the person who called you will either be forwarded to voice mail or hear the busy signal
– Say “Ignore” after the caller is announced.*

Make a call*
– Tap the Voice button and you will be prompted to “Say a command”. You can then:
– Say ”Redial” to redial last outgoing number
– Say ”Call back” to call back the last incoming number*
– Say ”Phone commands” to activate the voice dialing feature on your phone**
– You can also place a call directly from your phone. If your phone is connected it will automatically transfer the call to your Jabra FREEWAY*. If the call does not transfer, tap the Answer/end button.

Last number redial*
– Double tap the Answer/End button

Activate Voice dialing**
– Press the Answer/end button to activate the phones voice dialing or tap the Voice button and say “Phone commands”.*

Mute/un-mute
– Tap the Mute button during a call to mute your microphone during a call and again to turn mute off.
Adjust sound and volume
– Tap the Vol- or Vol+ buttons to adjust the volume when on a call or listening to wireless on your Jabra FREEWAY.
Three way calling*
– Press the Answer/end button to switch to call on hold. Press the Answer/end button to switch back to first call.
Play music*
– If your phone supports A2DP audio streaming then you can transfer music or any other type of audio to the FREEWAY.
Answer a call while playing music*
– If you have an incomming cal while listening to music on the Jabra FREEWAY the music will pause and you will hear your ringtone or caller ID. You can then chose to aswer or ignore the call. After the call the music will start to play again*.

JABRA VOICE FEATURES
JABRA VOICE FEATURES

When you have an incoming call you can answer or ignore just using you voice. You do not have to touch Jabra FREEWAY or you phone. Just say “Answer” to take the call and “Ignore” to reject.

Voice control

At any time when you are connected to a phone you can tap the Voice button, wait for Jabra FREEWAY to ask you to ”Say a command”, and then say one of the following commands.

Outgoing calls
start music

When you are playing music on the Jabra FREEWAY you can at any time tap the Voice button to remote control you music player using your voice.
While listening to music

The Jabra FREEWAY is loaded with voice announcements that talks you through setup and daily operation. In the table below you can see the most common announcements.

Voice guidance

ADDITIONAL FEATURES
Play music, podcasts and audio from GPS applications*
If your phone or device supports A2DP audio streaming you can hear your music or any other audio through your Jabra FREEWAY. Simply start playing your music or start your application and the audio will automatically transfer to FREEWAY. If your phone rings the audio will mute and you can answer or ignore the call. The audio will resume after the call.*

You can also start your music player by tapping the Voice button.
Wait for the FREEWAY to ask you to ”Say a command” and then say ”Play”*.
When playing music you can at any time tap the Voice button
again and:
– Say ”Next track” and ”Previous track” to skip between songs
– Say ”Stop” or ”Play” to start or stop your music

If you want to exit A2DP streaming mode or stop the music you can:
– Tap the Voice button and say ”Stop”
– Stop the music/audio in your device
Using you Jabra FREEWAY with two mobile devices at the same time The Jabra FREEWAY supports Advanced MultiUse™ and is capable of having two mobile phones (or other Bluetooth® devices) connected at the same time. This will give you the freedom of having only one headset to operate both of you mobile phones/ devices.

When you have two active phones/devices connected you will hear ”Two devices connected”. In this state the phone paired last will be used for voice dialing. When two phones are connected you can place and answer calls on both and switch between the two. If you are on a call and receive a second call you will be alerted by a tone. You can then:
– Put the first call on hold and accept the incoming call by pressing the Answer/end button
– Switch between the two active calls by pressing the Answer/ end button again
– Tap the Answer/end button once to end the first call and accept the new incoming call

FM Transmitter
You can transmit your calls, music and GPS directions from your phone/device to your car stereo using the built-in FM transmitter.

Tap the FM button and set your radio to the announced frequency.
If you experience interference from a radio station on your set frequency you can either tap the FM button to quickly redirect the audio back to the FREEWAY or press the VOL+ button to search for a new frequency.

If your radio supports RDS it will automatically adjust to the new frequency. If it doesn’t you have to manually set the radio to the new frequency.

Note: When in FM mode the volume controls on the FREEWAY are disabled. Use the volume control on your car radio instead. QUICK REFERENCE TABLE FOR MANUALLY CONTROLLING YOUR JABRA FREEWAY

FM mode
FM mode

Download Firmware updates and additional languages
Go to jabra.com/freeway and download the latest firmware and additional languages.

TROUBLESHOOTING & FAQ
I hear crackling noises
– Bluetooth is a radio technology, which means it is sensitive to objects between the speakerphone and the connected device.
It is designed for the speakerphone and the connected device to be used within 33 feet (10 meters) of each other, with no major objects in the way (walls, etc.).

I cannot hear anything in my speakerphone
– Increase the volume in the speakerphone.
– Ensure that the speakerphone is paired to a device that is playing.
– Make sure your phone is connected to the speakerphone by tapping the Answer/End button.

I am having pairing problems
– You may have deleted your speakerphone pairing connection in your mobile phone/device. Follow the pairing instruction to pair it again.

I want to reset the pairing list in my speakerphone
– The speakerphone registers a list of up to 7 mobile phones. To clear the pairing list and reset the Jabra FREEWAY to factory settings you can turn the FREEWAY on while pressing the FM, Voice and Answer/end button for about 6 seconds. The next time you power on the Jabra FREEWAY it will automatically go into pairing mode.

Will the Jabra FREEWAY work with other Bluetooth equipment?
– The Jabra FREEWAY is designed to work with Bluetooth mobile phones. It can also work with other Bluetooth devices that are compliant with Bluetooth version 1.1 or higher and support a headset, hands-free and/or advance audio distribution profile.

I cannot use Reject call, call on hold, Redial or voice dialing
– These features are dependent on the ability of your phone to support a hands-free profile. Even if the hands free profile is implemented reject call, call hold and voice dialing are optional features which are not supported by all devices. Please consult your device manual for details.

Please note that some features can only be operated from the primary device e.g. voice dial using Jabra FREEWAY with 2 mobile phones.

I can not connect speakerphone and radio via FM transmitter
– Make sure the radio is turned on and speakerphone is in FM mode (FM Status Icon is on).
– If your radio when searching is not able to find the FM frequency set by your speakerphone, the FM frequency must be tuned in manually on the radio. Please read radio manual to find out how to manually change frequency on your radio.
– If your radio is in TA (Traffic Announcement) mode, switch TA off and your radio should be able to find your speakerphone when using the search function on the radio. If not tune in manually.

– The sensitivity of the search function on your radio determines whether it is able to find the frequency set by your speakerphone. On some radios you are able to adjust the sensitivity thus making it possible to find the speakerphone frequency when searching. If not tune in manually.

– In urban areas it might be difficult to find a clear frequency. It is therefore advisable to use a frequency in the lower or upper end of the FM frequency band (e.g. 88.1 or 107.7 MHz) where you will have the best chance to find a clear frequency.

My Jabra FREEWAY does not announce the caller names during incoming calls
– Ensure that your phone supports the Bluetooth® phonebook access profile (PBAP) and that the name of the caller is in you phonebook.

Please note that on some Android phones a warning message about the phonebook transfer appears in the top left corner. You must select this message and agree to the connection in order to get caller ID to function properly.

TAKING CARE OF YOUR SPEAKERPHONE
– Always store the Jabra FREEWAY with the power off and safely protected.
– Avoid storage at extreme temperatures (above 45°C/113°F –
including direct sunlight – or below -10°C/14°F). This can shorten battery life and may affect operation. High temperatures may also degrade performance.
– Do not expose the Jabra FREEWAY to rain or other liquids

GLOSSARY
1 Bluetooth is a radio technology that connects devices, such as mobile phones and headsets, without wires or cords over a short distance (approx. 10 meters/33 feet). Bluetooth is safe to use. It is secure too, so once a connection has been made no-one can listen in and there is no interference from other Bluetooth devices either. Get more information at www.bluetooth.com.

2 Bluetooth profiles are the different ways that Bluetooth devices communicate with other devices. Bluetooth phones support the headset profile, the hands-free profile or both. In order to support a certain profile, a phone manufacturer must implement certain mandatory features within the phone’s software.

3 Pairing creates a unique and encrypted link between two Bluetooth devices and lets them communicate with each other. Bluetooth devices will not work if the devices have not been paired.

4 Passkey or PIN is a code that you enter on your Bluetooth enabled device (e.g. a mobile phone) to pair it with your Jabra FREEWAY. This makes your device and the Jabra FREEWAY recognize each other and automatically work together.

5 Standby mode is when the Jabra FREEWAY is passively waiting for a call. When you ‘end’ a call on your mobile phone, the speakerphone goes into standby mode.

DisposeDispose of the product according to local standards and regulations.
www.jabra.com/weee

© 2011 GN Netcom US, Inc. All rights reserved. Jabra® is a registered trademark of GN Netcom A/S. All other trademarks included herein are the property of their respective owners. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by GN Netcom A/S is under license. (Design and specifications subject to change without notice).

MADE IN CHINA
TYPE: HFS100

FCC

www.jabra.com

THANK YOU
Thank you for purchasing the Jabra FREEWAY Bluetooth® speakerphone. We hope you enjoy it! This instruction manual will get you started and ready to make the most of your speakerphone.

Logitech K800 Keyboard Manual


Logitech K800 Keyboard Manual

Logitech
Getting started with
Logitech® Wireless Illuminated
Keyboard K800

Contents
Contents

Unifing

ON OFF

Your Keyboard is now ready for use.Optional:
For the option of reprogramming your keyboard’s enhanced F-key functions, download the free Logitech® SetPoint™ Software at www.logitech.com/downloads

Keyboard features: F-key usage
User-friendly enhanced F-keys let you launch applications easily. To use the enhanced functions (yellow icons), first press and hold the ‘/ key; second, press the F-key you want to use.

Tip: In the software settings, you can invert the FN mode if you prefer to access directly the enhanced functions without having to press the FN key.
Keyboard features

*Requires SetPoint™ Software (available for download at www.logitech.com/downloads).

Features

1. Application zone
+ F1 Launch Internet browser’
+ F2 Launch e-mail application’
+ F3 Launch Windows Search*’
+ F4 Flip†

2. Convenience zone
+ F5 Backlight down by 25%’
+ F6 Backlight up by 25%’
+ F7 Battery check’
+ F8 Sleep mode

3. Multimedia navigation zone
+ F9 Launch media’
+ F10 Previous track’
+ F11 Play/Pause’
+ F12 Next track

4. Multimedia volume zone
Multimedia volume zone

5. FN key

6. Automatic light sensor (ALS)

7. Battery status indicator

8. Keyboard power switch

* One Touch Search if the SetPoint® software is installed.† Application Switcher if the SetPoint® software is installed.

Keyboard Back-lighting
When you switch on the keyboard, all keys are back-light at full intensity for five seconds. The back-lighting adjusts itself automatically based upon the ambient light in your room.

Keyboard backlighting

To activate backlighting, move your hand over the keyboard, or press a key. There is a proximity sensor in the keyboard that detects motion and switches on backlighting.

Backlighting remains on while you charge the keyboard. When keyboard battery power is very low, the lower battery LED blinks red and backlighting is switched off to conserve battery life.

Press FN + F5 to decrease backlighting and FN + F6 to increase it. There are fi ve levels of illumination: 0%, 25%, 50%, 75%, and 100%. More battery power is used as the level of illumination is increased. After three hours of inactivity or if the keyboard is restarted, the backlighting level returns to automatic adjustment.

Recharging the keyboard
Typically, you can expect about 10 days of battery life before you will need to recharge the keyboard battery.* If the backlighting level is set to 100%, you have about 15 hours of battery life.

To recharge the keyboard, connect it to your computer using the USB recharging cable. A full battery recharge takes about 5 hours and only 3 hours if the keyboard has been switched off.
Recharging the keyboard

* Battery life varies with usage, backlighting level, and computing conditions. Heavy usage usually results in shorter battery life.

Unifying

Plug it. Forget it. Add to it.
You’ve got a Logitech® Unifying receiver. Now add a compatible wireless keyboard or mouse that uses the same receiver. It’s easy. Just start the Logitech® Unifying software* and follow the onscreen instructions. For more information and to download the software, visit www.logitech.com/unifying

*Go to Start / All Programs / Logitech / Unifying / Logitech Unifying Software

Help with setup
Keyboard is not working

1. Check the Unifying receiver. Also, try changing USB ports.

2. Move closer? Try moving the keyboard closer to the Unifying receiver, or plug the Unifying receiver into the receiver extender cable to bring it closer to the keyboard.

USB ports
3. Check battery level

4. Is the keyboard turned on? Slide the keyboard Off/On switch to the On position. The keyboard Status LEDs should light up.

keyboard turned on

5. Re-establish the connection. Use the Unifying software to reset the connection between the keyboard/mouse and Unifying receiver. Refer to the Unifying section in this guide for more information (p. 13).

6. Restart the computer.

supportwww.logitech.com/support

logitech support

FCC ID

www.logitech.com

© 2010 Logitech. All rights reserved. Logitech, the Logitech logo, and other Logitech marks are owned by Logitech and may be registered. All other trademarks are the property of their respective owners. Logitech assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change without notice.620-002354.004

Logitech

SoundPARA Nano Earbuds Manual

SoundPARA Nano Earbuds

SoundPARA Nano Earbuds Manual

MANUFACTURER
Shenzhen SoundSOUL Information Technology Co.,LTD
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 51810
[email protected]
www.dudios.com

FCC ID

Package Content

Package Content

 

Specifications
Bluetooth Version : V5.0
Maximum working range : 33 feet (10m, without obstacle)
Bluetooth Chip set : Realtek 8763BFR
Working Time : 4 hours
Earbuds Charging Time : 2 hours
Charging Case Charging Time : 2 hours
Charging Case Recharge Earbuds : 3-4 times (both earbuds)
Weight : 0.13oz / 3.7g
Dimension (L * W * H) : 1.1 x 1 x 0.6 inches / 27 x 25 x 16 mm

 

Button Controls
Button Controls

Button Controls table

Wearing
1. Identify the left and right earbuds.
2. Insert the earbuds into your ears and adjust to find best angle with microphone downwards.
3. Make sure the eartips seal the ear canals.

Wearing

Getting Started
1. Take out both earbuds from the charging case, the two earbuds will flash in white at first. Then the le indicator goes out, and right indicator fashes in red and white with voice prompt “pairing”.

2. Activate the Bluetooth in your device and hit “SoundPARA Nano” on the Bluetooth list, once paired, the right earbud will hear a voice prompt “connected”.

3. The earbuds can remember previously paired devices. They would automati-cally connect to the last device they have paired before aer being taken out from the case. If not, hit “SoundPARA Nano” on the Bluetooth list and re-connected it.

Wearings

Note
1. If Le earphone doesn’t connect with Right one within 15 seconds when taking out both from charging case, it will be into standby status. And it will enter into pairing mode again by putting le earbud in charging case and waiting for 3s to be taken out again. (The le one will turn o automatically when in standby mode for 3 minutes)

2. If you want to replace the paired device while it’s connected, you can force the headset to go into pairing mode by long pressing the MFB of right earbud for 6s while the headset is o.

Factory Reset
(Try the following steps if you fail building connection between two earbuds, or between earbuds and device)1. Clear the pairing record between the earbuds and all of your devices. 2. Hold and press the MFB of both earbuds for 10 seconds when in charging status, the LED indicator will flash red for 3 times if resetting successfully.

Charging
SoundPARA Nano Bluetooth earphones are equipped with a compact and lightweight charging case which is not only a charging dock to charge the earphones, but also a carrying case. With a built-in rechargeable battery, the charging case can provide up to 3-4 times full charge for the earphones (both left and right

Charging the headset
The earphones are partially charged at the factory. Please make sure they are fully charged before first use.1.Put the earphones into corresponding charging slots, make sure the charging contractors are match.2.The LED indicators on the earphones turn red to start charging.3.The earphones are fully charged when LED indicators turn white and turn o aer 1 minute

Charging the case
The charging case can not power o the earbuds or charge them if the case battery is low or dead. Please charge the case soon.
1.Connect the charging port with any USB charging adapter(The current is no greater than 1A).
2.Please charge the earphones at least once every 3 months when not in use for a long time

Charging the case

Warranty
We warrant this device 12 MONTHS from date of the original purchase for manufacturer defects.
[email protected]
Please scan the QR code or search the link below for detailed PDF manual

QR Code
http://dudios.com/index.php/list/index/id/64.htm

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Soundpeats Q12 Plus Manual

Soundpeats Q12 Plus

Soundpeats Q12 Plus Manual

MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[email protected]
www.soundpeolsoudo.com

FCC ID

Introduction
Thank you for choosing SoundPEATS Q12 Plus Bluetooth headphones. Please read this manual carefully, and keep it for further reference. If you need any assistance, please contact our customer support team by emailing [email protected]

Package Content
Package Content

Product Diagram
Product Diagram

Specifications
Specifications

Get Comfortable
Fit to your ear
The SoundPEATS 012 Plus earphones come with 6 different sized interchangeable ear tips and 8 ear fins (2pcs on the earphones Included). Please choose the right size to find the most secure and comfortable option for yourself (normally the medium ones are suitable for 75% of people).

Wearing the Headphones
1. Identify the left and right earpieces. 2.insert the earbuds into your ears, and adjust the our fins to find best angle until they fit flush In your ears and the ear tips seal In ear canal.

Wearing the Headphones

Getting Started

Charging
The headset is partially charged In the factory. Please make sure it is fully charged before first use.

1.Connect the charging port with any USB charging adapter or USB port available. Charging starts automatically with LED Indicator turning red and the headset turns off.
2.The headset is fully charged when the LED indicator turns blue.

Note:
1.The LED indicator flashes red with a voice prompt ° battery low° when the battery is running out. Please recharge the headset.
2.Charge the headset at least once every 3 months when not using for a long time.
3. When charging with a USB adapter, the charging current should not be greater than 1A.Please do not use any quick charger to charge the head-phones.

Pairing
To pair the Bluetooth headset with your device. you must first bring it into pairing mode.

1. Please turn off other Bluetooth device nearby and make sure the headset and your Bluetooth device are close enough(within 3 feet)

2. Power on the headset, wait until the LED Indicator flashes blue and red. Now the headset is in pairing mode.

3. Activate the Bluetooth in your device and search for nearby Bluetooth connection: For iPhone/iPad/iPod®: Settings->Bluetooth->On For Android-TM: Setting->Bluetooth->On->Scan for devices For Windows®Phone devices: Settings->Blue-tooth->On

4.”SoundPEATS Q12 Plus”should be listed in the search result. Select the name to connect. Once connect-ed, the indicator is solid blue. You will hear a voice prom pr Your headset is connected”.

Note:
1. The 012 Plus headset will stay in pairing mode for 3 minutes at most if no pairing device is found. Afterwards, it will power off automatically.

2.Maximum operating range for the Bluetooth headset is 33ft(1 Om) without obstacles. If you move out of the range, the headset will lose connection. You will need to move back to be within the range and reconnect to your Bluetooth device.

Re-pairing
The SoundPEATS 912 Plus Bluetooth headset can remember devices paired before. If you have previously paired the headset with a device, simply turn on your device and the headset (by pressing the Multi functional button for 3 seconds), they will automatically connect to each other within 10 seconds.

Multi point Pairing
The 912 Plus headset is capable of simultaneously connecting to two devices. To do this
1.Follow the “Pairing” section to pair the 912 Plus headphones with your first device.

2.Deactivate the Bluetooth In your first device after pared, and turn off the 012 Plus headphones,

3.Follow the “Pairing” Instruction to pair your second device with the headphones.

4. After pairing to your second device successfully, please turn on the Bluetooth of your first device and select the Bluetooth name °SoundPEATS 012 Plus° to connect. Now both devices are paired with the 912 Plus headphones. you can make / answer phone calls from either device.

Note:
1. Although you can pair two devices with the headphones only one of them can play music with the headphones at a time.

2. To switch between the two devices simply pause the music on one device and play music on the other or vice versa. •

Reset
The SoundPEATS 012 Plus Bluetooth headset con be reset by pressing the Multi function button for 3s while charging. The LED indicator will flesh blue twice.

Controls and Voice Notification
Button Controls
Once connected, the 012 Plus Bluetooth headphones can manage media and phone calls on a smartphone or tablet

Button Controls

Voice Notification
Button Controls

LED Indicator
The LED Indicator gives a good indication of what the headset is doing.
LED Indicator

Trouble Shooting
Q. The headset is on, but it is not connecting to my Device?
A: Please follow the Taking” section In this manual to pair them at first. If it doesn’t work normally, please try to reset the headphones at first, and clear the pairing list in your Bluetooth device, then restart both of them and pair again.

Q: I have established connection with my smartphone. but I am not hearing any sound?
A: Please turn up the volume on both the headphones and your smartphone. Some smartphones require you to set up the Bluetooth headset as an audio output device before sound Is transmitted. Please read the instruction of your smartphone for details. If you are using a music player or other Bluetooth device. please make sure it supports A2DP stereo music profile.

Q: The sound is not very clear / the caller cannot hear my voice clearly?
A: Please adjust the volume on your phone and headphones. Make sum there is no signal interference nearby. Meanwhile. please hold the microphone closer to your mouth while talking through the headphone, and stay close to your phone.

Q: Can I use the headset while it is Charging?
A: No the headset can not be used while charging.

Q.: Why the connection is not stable and cuts out intermittently?
A: Bluetooth signal transmission doesn’t work as Wi-Fi or some other wireless signal it would be affected by wireless signal around and barriers between. Please make sure there are no objects between the headphones and your Bluetooth device, and also no radio or Wi-Fi interference nearby.

Q: What is the range of the Bluetooth headphones?
A: The Bluetooth headphones have maximum range of 33 feet (10m). However the actual range will depend on usage and environment Connection is usually good within 1525 feet with no major obstacles between.

Q: My headset WI not switch on.
A: Please recharge It and make sure It has enough battery power. If if is fully charged and still nothing happens or ff you are not able to charge the unit, please contact our customer support for warranty cover.

Care and Maintenance
• Keep the headset away from heat and humidify.
• Do not put the product under direct sunlight or not areas. High temperatures will shorten lifespan of the
headset, battery and / or the Internal circuit board. Power off the headset when not in use and before Storing.
• Do not try to take the product apart.
• Do not drop or knock your headset on hard surfaces.
• Do not use chemicals or detergents to clean the product.
• Do not scrape the surface web sharp objects.

Warranty and Support
Customer Support
If you need any assistance or support, please email
[email protected] with details.
We will answer your email within 24 hours. We will do our best to provide you with a viable solution.

Warranty
We warrant this device 12 MONTHS from date of the original purchase for manufacturer defects. If the device falls due to o manufacturing defect, please contact seller directly to initiate return and warranty process.

The following are exceeded horn SoundPEATS warranty cover.
• Device purchased as second hand, used or from unauthorized seller.
• Damage resulted from misuse and abusive action.
• Damage resulted from chemical, fire, radioactive substance, poison. laud.
• Damage resulted from natural disaster.
• Damage caused to any third party / person / object and beyond.

Statement
We con only provide after sole service for products purchased directly from SoundPEATS or SouncIPEATS outs:ft.! distributor. If you have purchased from different select please contact Them for any exchange or refund request

[email protected] is a registered Trademark of Bluetooth SIG Inc.

Soundpeats TrueCapsule Earbuds Manual

TrueCapsule

Soundpeats TrueCapsule Earbuds Manual

MANUFACTURER
Shenzhen SoundSCHR Information Technology Company Limited
Location: Room 1308-1309, Building B, Huhal Square, Chuangye Road, Longhua District. Shenzhen. China. 518109
Email: [email protected]
Website: www.soundpeatsaudio.com

Made in China

Introductions:
Thank you for choosing SOUNDPEATS TrueCapsule Bluetooth earphones. Please read the manual carefully, and keep it for further reference. If you need any assistance, please contact our customer support team at [email protected]

Package of Content
Content

Product Diagram
Product Diagram

Specifications

Specifications

Make Comfortable
Wearing the earphones
1. Identity the left and right earbuds.
2. Rotate the earbuds, and adjust to find the best angle.
3. Make sure the ear tip seals VI the ere canal.
Wearing the earphones

Getting Started
Charging
SOUNDPEATS TrueCapsule Bluetooth headset comes with a charging case which can be used as a charging dock to charge the earphones and also a carrying case. With a built-in rechargeable battery, the charging case can provide up to 5-6 times full charge for the earphones (both left and right).

Charging the headset
The earphones are partially charged at the factory. Please make sure they are fully charged before first use. 1Put the earphones into corresponding charging docks. make sure the charging contactors are match. 2.The LED indicator will turn red when it starts charging. 3.The red LED indicator will turn off when the earphones are fully charged.

Charging the case
When charging case battery Is low, the last Indicator of the charging case will flash white, Please charge the case soon. 1.Connect the charging port with USB charging adapter. (Please make sure the current Is not greater than 1A) 2.Please charge the case at least once every 3 months when not in use for a long time.

Charging

Pairing
The SOUNDPEATS TrueCapsule earbuds can enter pairing mode automatically, please follow the pairing steps below to build connection.
1. Before start, please turn off other Bluetooth devices nearby, and make sure the earphones and your Bluetooth device are close enough (within 1 m).

2.Pick up the left and right earbuds at the same time from the charging case when the charging case Is powered. The earphones will turn on automatically with a voice prompt ‘power on°, while the indicator will stay solid white for around Is.

3.The both earbuds enter TWS Pairing mode automatically, while white indicator flashes quickly. You will hear a voice prompt when the left and right earbuds connect to each other successfully.

4.Then the Indicator of left earbud Is going off, and the right indicator still alternately flashes in red and white with a voice prompt °pairing” indicating pairing mode.

5.”SOUNDPEATS TrueCapsule” will show up on the Bluetooth list click it to connect. You will hear a voice prompt °connected” when the earbuds connect with your device successfully.

Pairing

Re-Pairing
SOUNDPEATS TrueCapsule Bluetooth earbuds can remember previously paired devices. When you make the second connection. simply activate the Bluetooth in your device. take out the both earbuds from the charging case. They will connect to each other and reconnect to your device automatically. If the earbud doesn’t automatical-ly connect to your device, please activate the Bluetooth in your device and hit °SOUNDPEATS TrueCapsule° on the Bluetooth int.

Note:
1.If the left earbud Is taking out from the charging case first and didn’t pair with the right earbud aim n 10 seconds, the !eh earbud will enter the standby mode. Please place the earbuds back Into the charging case and taking them out again after 3s, the earbuds will enter the pairing mode again. Otherwise, the let earbud will stay in standby mode for 3 minutes and then turn off.

2.If you wont to change the pairing device In the connected state, please turn offr4 both earbuds, then press and hold the multifunction button of the right earbud for Fs to have renter pairing mode directly and pair to a new device.

3.The headset will automatically turn off if it doesn’t connected to any device for 5 rninutes in pairing mode.

4.The maximum operation range for the Bluetooth earphones is 33 ft(10m). If you move out of the range, the earphones will lose connection. You will need to move back to be within the range and reconnect to your Bluetooth audio device.

Factory Reset
(Try the following steps if you fail building connection between two earbuds, or between earphones and device)

1.Clear pairing record between the earbuds and all your devices.

2.Place back both earbuds into the charging caseand ensure they’re in charging status. Then long press the multi function button of both earbuds for 10s, until the LED light of both earbuds flash white twice.

Control and Voice Notification

Touch Control

Touch Control

LED Indicator

LED Indicator

Charging Case Indicator
Charging Case Indicator

Trouble Shooting
Q: Can I use both earphones separately?
A: It Is not recommended to use In mono mode. If you prefetfust wearing One eOrbUd. only the right earbucl supports working alone, the left earbucl can’t.

0: The earphones are hiring on, but it doesn’t connect to my device?
A: To connect the headset to your device. please check if the Bluetooth of the device Is on at first. then select the name of the headset on the Bluetooth lot to get paired. if the headset still can’t connect to your device, please try to reset it or contact our customer support.

Q: I have established connection with my smariphone, but I am not hearing any sound?
A: Please confirm that you have raised the sound of your phone and headphones to an audible range. Some smarfinhone requires you to setup the Bluetooth headset as an audio output device before sound is transmitted. Please see the Instruction of your smartphone for details. If you are using a music player or other Bluetooth device, please make sure It supports A2DP stereo music profile.

Q: The sound Is not very dear / the caller cannot hear my yoke dearly?
A: Please adjust the volume on your phone and earphones. Make sure there is no source of Interference nearby. Stay close to your phone.

Q: Why the connection is not stable and cuts out intermittently?
A: Please make sure there are no objects between the earphones and your Bluetooth device, and make sure them Is no radio or WWI Interference nearby.

Q: What is the range of Bluetooth earphones?
A: Bluetooth earphones have maximum range of 33 feet (10m, no obstacle). However the actual range will depend on usage and environment. Connection Is usually good within 15-25 feet with no major obstacles between devices.

Q: My earphones will not switch on.
A: Please recharge h and make sure El hos enough battery power. If ft is fully charged and still nothing happens or if you are not able to charge the unit, please contact our customer support for warranty cover. An.

Care and Maintenance
• Keep the earphones away from heat and humidity.
• Do not put the product under direct sunlight or hot areas. High temperatures will shorten lifespan of the earphones, battery and / or the internal circuit board.
• Power off the earphones when not In use and before storing.
• Do not try to take the product apart.
• Do not drop or knock your earphones on hard surfaces.
• Do not use chemicals or detergents to clean the product
• Do not scrape the surface with sharp objects.

Warranty and Support
Customer Support
If you need any assistance or support, please email [email protected] with details.
You will hear from us within 24 hours. We will do our best to provide you with a viable solution.

For more Information, please visit www.soundpeatsaudlo.com.

warranty
We warrant this device 12 MONTHS from date of the original purchase for manufacturer defects. If the device falls due to a manufacturing defect,
please contact seller directly to initiate return and warranty process.

The following are excluded from SOUNDPEATS warranty cover:
• Device purchased as second hand, used or from unauthorhed seller
• Damage resulted from misuse and abusive action
• Damage resulted from chemical. fire. radioactive substance. poison. liquid
• Damage resulted from natural disaster
• Damage caused to any third party / person / object and beyond

Statement:
We can only provide after sale service for products purchased directly torn SOUNDPEATS or SOUNDPEATS authorted distributor. If you have purchased from a different seller please contact them for any exchange or refund request.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule, These limits are designed to provide reasonable protection against harmful interference In a residential installation. This equipment generates uses and can radiate radio frequency energy and if not Installed and used inaccordance with the instructions, may cause harmful Interference to radio communications. However. there s no guarantee that Interference will not occur In ma particular Installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on, the user Is encouraged to try to correct the Interference by one or more of the following measures.
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver b connected.
— Consult the dealer or an experienced radionV technician for help.

This device compiles with part 15 of the FCC Rules. Operation issubJect to the following two conditions:
(1) This device may not cause harmful Interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. (3)this device has been evaluated in meet general RF erposure requirement The device can be uoed in portable exposure condeon without restriction.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Whirlpool WHER25 Manual

Whirlpool WHER25
Whirlpool

Whirlpool WHER25 Manual

Model WHER25
How to install, operate
and maintain your
Reverse Osmosis
Drinking Water System
Do not return unit to store

nstalling, operating or maintaining your reverse osmosis system, call our toll free number:
1-866-986-3223
Monday- Friday, 8 AM – 7 PM EST or visit
www.whirlpoolwatertreatment.com
When you call, please be prepared to provide the model, date code and serial number of your product, found on the rating decal, located inside the cover.

System tested and certified by NSF International against NSF/ANSI Standards 42 & 58. See performance data on page 26 for details.

Manufactured and warranted by Ecodyne Water Systems 1890 Woodlane Drive Woodbury, MN 55125

7322259 (Rev L 11/21/14)
Product No. 8576162B

WARRANTY
ONE YEAR LIMITED WARRANTY ON REVERSE OSMOSIS DRINKING WATER SYSTEM
(Except filter cartridges and R.O. membrane)
Warrantor: Ecodyne Water Systems, 1890 Woodlane Drive, Woodbury, MN 55125
Warrantor guarantees, to the original owner, that the Reverse Osmosis Drinking Water System, when installed and maintained
in accordance with the instructions, will be free from defects in materials and workmanship for a period of one (1)  year from the date of purchase. If, within the first year, a part proves, after inspection, to be defective, Warrantor will, at its sole option, either replace or repair the part without charge except normal shipping and installation charges. Labor to maintain the equipment is not part of the warranty. Filters and membranes, which are expendable, are not covered by the warranty.

TO OBTAIN WARRANTY PARTS, SIMPLY CALL 1-866-986-3223, Monday – Friday, 8 am – 7 pm EST, for assistance. This warranty applies only while this product is in use in the United States or Canada.

General Provisions
The above warranties are effective provided the Reverse Osmosis Drinking Water System is operated at water pressures not exceeding 125 psi, and at water temperatures not exceeding 100°F; provided further that the Reverse Osmosis Drinking Water System is not subject to abuse, misuse, alteration, neglect, freezing, accident or negligence; and provided further that the Reverse Osmosis Drinking Water System is not damaged as the result of any unusual force of nature such as, but not limited to, flood, hurricane, tornado or earthquake. Warrantor is excused if failure to perform its warranty obligations is the result of strikes, government regulation, materials shortages, or other circumstances beyond its control.

*THERE ARE NO WARRANTIES ON THE REVERSE OSMOSIS DRINKING WATER SYSTEM BEYOND THOSE SPECIFICALLY DESCRIBED ABOVE. ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, ARE DISCLAIMED TO THE EXTENT THEY MIGHT EXTEND BEYOND THE ABOVE PERIODS. THE SOLE OBLIGATION OF WARRANTOR UNDER THESE WARRANTIES IS TO REPLACE OR REPAIR THE COMPONENT OR PART WHICH PROVES TO BE DEFECTIVE WITHIN THE SPECIFIED TIME PERIOD, AND WARRANTOR IS NOT LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES. NO WARRANTOR DEALER, AGENT, REPRESENTATIVE, OR OTHER PERSON IS AUTHORIZED TO EXTEND OR EXPAND THE  ARRANTIES EXPRESSLY DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts or exclusions or limitations of incidental or consequential
damage, so the limitations and exclusions in this warranty may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. This warranty applies to consumer-owned installations only.

Non-potable Water Sources: Do not attempt to use this product to make safe drinking water from non-potable water sources. Do not
use the system on microbiologically unsafe water, or water of unknown quality without an adequate disinfection before or after the
system. This system is certified for cyst reduction and may be used on disinfected water that may contain filterable cysts.

Arsenic Reduction: This system shall only be used for arsenic reduction on chlorinated water supplies containing detectable residual free chlorine at the system inlet. Water systems using an inline chlorinator should provide a one minute chlorine contact time before the reverse osmosis system.

Nitrate/Nitrite Test Kit: This system is acceptable for treatment of influent concentrations of no more than 27mg/L nitrate and 3mg/L
nitrite in combination measured as N. It is certified for nitrate/nitrite reduction only for water supplies with a pressure of 280 kPa (40
psig) or greater. This system is supplied with a nitrate/nitrite test kit. Product water should be monitored periodically according to the
instructions provided with the test kit.

TDS Test Kits: TDS test kits are available by calling 1-800-949-8220 or check the water testing section of your local phone directory.
Installations In The Commonwealth Of Massachusetts: The Commonwealth of Massachusetts requires installation be performed
by a licensed plumber and do not permit the use of saddle valves. Plumbing code 248-CMR of the Commonwealth of Massachusetts
must be followed in these cases.

Product Water Testing: The Reverse Osmosis system contains a replaceable treatment component critical for the effective reduction
of total dissolved solids. Product water should be tested periodically to verify that the system is performing properly.

Replacement of the reverse osmosis component: This reverse osmosis system contains a replaceable component critical to the
efficiency of the system. Replacement of the reverse osmosis component should be with one of identical specifications, as defined by the manufacturer, to assure the same efficiency and contaminant performance.

Product Water Testing

Inspect Shipment

Your Reverse Osmosis Drinking Water System is shipped complete in one carton. Remove all items from your shipping carton.
Check all items against the packing list below. Note any items lost or damaged in shipment.

Note any damage to the shipping carton. Refer to the exploded view and parts list in the back of the manual for the part names and numbers of missing or damaged items. If problems exist, refer to the website or the toll free number listed throughout this manual.

Keep the small parts in the parts bag until you are ready to install them.

NOTE: Codes in the state of Massachusetts require installation by a licensed plumber and do not permit the use of saddle valves.

If you live in the state of Massachusetts, review plumbing code 248-CMR of the Commonwealth of Massachusetts before proceeding with the installation.

Packing List

Packing List

Packing List

Do not return the unit to store.
If you have any questions, or there are missing parts or damage, please call Toll Free 1-866-986-3223, Monday – Friday, 8 am – 7 pm EST, or visit www.whirlpoolwatertreatment.com When you call, please be prepared to provide the model, date code and serial number, found on the rating decal, located inside the cover.

Tools Needed

Review the tools needed list. See Fig. 3. Gather needed tools before proceeding with the installation. Read and follow the instructions provided with any tools listed here.

TOOLS NEEDED

TOOLS NEEDED to

Plan Your Installation
Read through the entire manual before beginning your installation. Follow all steps exactly. Reading this manual will also help you get all the benefits from your system.

Your Reverse Osmosis Drinking Water System can be installed under a sink or in a remote location. Typical remote sites are a laundry room or utility room. Review the location options below and determine where you are going to install your system.

UNDER THE SINK LOCATION
The Reverse Osmosis Filter Assembly and storage tank may be installed in a kitchen or bathroom sink cabinet. See Fig. 4. A suitable drain point is needed for drain water from the Reverse Osmosis system.

REMOTE INTERIOR LOCATION
The Reverse Osmosis Filter Assembly and storage tank may also be installed in a remote interior location away from the Reverse Osmosis Faucet. You will need a nearby water source and drain point. See Fig. 5.

CHECK SPACE REQUIREMENTS
Check size and position of items for proper installation into location chosen.

NOTE: For best system performance, the feed water to the system should be softened or have hardness less than 10 grains per gallon, with no iron.

Plan Your Installation

Typical Remote Installation

Questions about your Whirlpool WHER25 Manual ? Post in the comments!
Download Whirlpool WHER25 Manual Manual [PDF]

Shark NV42 Vacuum Cleaner Manual

Shark NV42 Vacuum Cleaner

Shark NV42 Vacuum Cleaner Manual

This manual covers model number:
NV42 26
TECHNICAL SPECIFICATIONS
Voltage: 120V.
Watts: 1200W
Amps: 10A
Hertz: 60Hz

Thank you for purchasing the Shark® Navigator® Deluxe Upright Vacuum.

Contents
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS For Household Use Only

WHEN USING YOUR SHARK® NAVIGATOR UPRIGHT VACUUM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK® NAVIGATOR UPRIGHT VACUUM.

POLARIZED PLUG:
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. Do not force into the outlet or try to modify the plug to fit.

POLARIZED PLUG

WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY DO NOT USE OUTDOORS OR ON WET SURFACES.

GENERAL ELECTRICAL SAFETY:

1. Unplug from electrical outlet when not in use and before servicing.
2. DO NOT use vacuum with a damaged cord or plug.
3. DO NOT pull or carry vacuum by the cord.
4. DO NOT unplug by pulling on cord; to unplug, grasp the plug, not the cord.
5. DO NOT handle plug or vacuum cleaner with wet hands.
6. DO NOT run the vacuum over the power cord.
7. DO NOT close a door on the cord.
8. DO NOT pull cord around sharp corners.
9. DO NOT leave appliance when plugged in.
10. Keep power cord away from heated surfaces.
11. Turn off all controls before plugging or unplugging vacuum cleaner.
12. Always turn off this appliance before connecting or disconnecting the motorized nozzle.

HOSE ATTACHMENTS:
13. DO NOT use if air flow is restricted; if the air paths, the hose or the extension tube become blocked, turn the vacuum cleaner off. Remove all obstructions before you turn on the unit again.
14. Keep the end of the hose, wands and other openings away from face and body.
15. Keep rotating brush and suction openings away from hair, face, fifingers, uncovered feet or loose clothing.
16. Only use manufacturer’s recommended attachments.

GENERAL USE:

17. Use only as described in this manual.
18. DO NOT put any objects into openings.
19. Keep your work area well lit.
20. Keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fifibers.
21. DO NOT place vacuum on unstable surfaces such as chairs or tables.
22. DO NOT allow young children to operate the vacuum or use as a toy.
23. DO NOT use vacuum with a damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to EURO-PRO Operating LLC for examination, repair, or adjustment

CYCLONIC CHAMBER/DUST CUP/FILTERS:
24. Before turning on the vacuum:
• Make sure that dust cup, cyclonic chamber and all fifilters are in place after routine maintenance.
• Make sure that all components and filters are thoroughly dry after routine cleaning.
• Only use filters and accessories provided by EURO-PRO Operating LLC [Failure to do so will void the warranty].

GENERAL CLEANING:
25. DO NOT run the vacuum over large-sized objects.
26. DO NOT pick up hard or sharp objects such as glass, nails, screws or coins that could damage the vacuum cleaner.
27. DO NOT pick up smoking or burning objects such as hot coals, cigarette butts or matches.
28. DO NOT pick up flammable or combustible materials such as lighter fluid, gasoline, kerosene or use in areas where they may be present.
29. DO NOT pick up toxic solutions such as chlorine bleach, ammonia or drain cleaner.
30. DO NOT use in an enclosed space where vapors are present from paint, paint thinner, moth-proofifing substances, flammable dust or other explosive or toxic materials.
31. DO NOT vacuum up any liquids.
32. DO NOT immerse vacuum cleaner in water or other liquids.
33. DO NOT use outdoors or on wet surfaces; use only on dry surfaces.
34. Use extra care when cleaning on stairs.

Getting Started

Getting Started

Along with your upright unit, you will find the following components:
a Vacuum Body
b Motorized Floor Brush
c Handle Assembly
d Super Stretch Hose
e Cleaning Wand
f Pet Hair Power Brush
g Cleaning Attachments
h 24” Crevice Tool

Navigator Upright

Your Shark® Navigator Upright is easy to assemble:
1 Lay your vacuum body on a level surface.
2 Slide the electrical connection from the motorized flfloor brush into the main body to click into place.
3 Connect the hose from the main body to the motorized flfloor brush; push with a slight turning motion to create a snug fit.

Navigator Upright is easy to assemble

4 Slide the handle assembly into the upright unit aligning the hose hook on the handle assembly with the power cord hooks on the back of the unit.
5 Secure the handle assembly in place with included nut/bolt (shipped attached to handle assembly).
6 Place the vacuum in the upright position.
7 Store the Crevice Tool, Dusting Brush and Cleaning Wand on the unit.

Super Stretch Hose

8 Attach the Super Stretch Hose:
a) Snap hose into swivel connector
b) Route under anti-tip hook
c) Route over upper hose holder
d) Press securely onto cleaning wand

IMPORTANT:
To prevent vacuum from tipping, secure hose under the anti-tip hose hook.

9 When storing your vacuum, wind cord around the two cord holders and secure with cord clip:
• Quick Cord release at the top of the unit – place in the upright position.
• Second holder near the base – turn until it is pointing down.
To release the cord, turn the Quick Cord release to the left or right.

IMPORTANT:
For suction to reach the Motorized Floor Brush, the Cleaning Wand and Super Stretch Hose must be attached securely on the vacuum body.

carry the vacuum

10 To carry the vacuum:
With the unit in the standing position, lift by the Dust Cup Assembly Handle (carry handle).

CAUTION: When lifting or carrying, DO NOT press Dust Cup Assembly release button.

Using the Vacuum

Using the Vacuum

Your Shark® Navigator Upright Vacuum is a versatile tool that can be used to clean bare flfloor surfaces or carpets – with the click of a switch.
Stand the vacuum into the upright position.
Plug in the vacuum.
1 Start with the Power Switch in the “O Off” position.
2 Place your foot on the motorized flfloor brush and pull handle towards you.
3 Set the Power Switch to desired cleaning setting.

When cleaning bare floors

4 When cleaning bare floors:
Select the “I On” position for suction only cleaning to avoid scattering dirt while cleaning.

When cleaning carpets:
Ensure you have pulled the handle towards you and select the “II Brush Roll On” position to agitate the carpet fibers for deeper cleaning performance.

5 Due to the huge suction power of this vacuum, it may become necessary to adjust the suction release on the hose. If the vacuum is difficult to push or pull or if it is lifting up area rugs, adjust the suction release by opening or closing the valve at the top end of the hose.

IMPORTANT:
To protect your carpets, the Brush Roll will only turn on when you have pulled the handle back towards you and released the Motorized Floor Brush.

IMPORTANT:
Your Brush Roll Indicator Light will illuminate solid green when brush roll is on, or solid red if there is a blockage. This feature is designed to protect your Lifetime Belt that powers your Brush Roll. See Checking for Blockages on page 11.

NOTE: The height of your Motorized Floor Brush has been optimized for easy pushing and superior cleaning on all flfloor types, so there is no need to make any height adjustments as you transition to different flfloor & carpet types.

Cleaning with the Vacuum Accessories

Cleaning with the Vacuum Accessories

Before cleaning with your accessories:
Stand vacuum into upright position.
Secure Super Stretch Hose in the anti-tip hose hook to prevent tipping.
Select the “I On” position for suction only cleaning.
DO NOT pull vacuum cleaner around by the hose.
DO NOT overextend the hose.

Vacuum Accessories

Vacuum Accessories
Your vacuum comes with a Super Stretch Hose and Cleaning Wand. Use one or the other to attach your cleaning accessories.
1 Using the Super Stretch Hose:
Stand the v
acuum into upright position.
Remove the hose from the Cleaning Wand.
Push the selected tool into the hose connector.

2 Using the Cleaning Wand:
Stand the v
acuum into upright position.
Remove the Cleaning
Wand (with hose attached) from the unit.
Push the selected tool into the end of the Cleaning Wand.
3 Pet Hair Power Brush
4 Dusting Brush
5 Crevice Tool
6 24” Crevice Tool
To order additional parts and accessories,
go to www.sharkclean.com or call
1-800-798-7398.

Emptying the Dust Cup Assembly
For best results empty the Dust Cup Assembly after each use; empty several times during prolonged usage.
Or empty the Dust Cup Assembly when it reaches the MAX fill line; NEVER OVER-FILL THE DUST CUP.
Stand vacuum into upright position.
Turn vacuum off.

CAUTION:
Unplug the vacuum; failure to do so might result in electric shock.

For proper care, consult the table to the right for the maintenance schedule of your Cyclonic Chamber and Filters.
Lock vacuum into upright position.
Turn vacuum off.
Remove Dust Cup Assembly.

Turn vacuum off

Insert Dust Cup Assembly

Allergy Sufferers

To empty the Dust Cup Assembly:
1 Grip carry handle and press the Dust Cup release button to remove Dust Cup Assembly
2 Option A: for Quick Empty:
Insert Dust Cup Assembly deep inside trash receptacle to contain dust and debris.

Press the Dust Cup Door release button; tap container gently to dislodge and release dust and debris.

Snap door in place.
Important: If the Dust Cup Door does not swing open after pressing the release button, push the door open using the bottom door tabs.

3 Option B: For Allergy Sufferers:
Wrap a trash bag around the Dust Cup Assembly leaving space at the bottom for the door to swing open.

Locate the Dust Cup Door release button within the trash bag and press to release as you shake the dust cup to empty dust and debris.
Snap the bottom door in place.

Note: Option B can also be performed outside of the home to further minimize releasing dust back into the air. Carry just the Dust Cup Assembly and trash bag outside.

Note: Some dust and debris may remain in the top of your dust cup assembly on or near the metal screen. It is not
necessary to completely remove this material before continuing to vacuum; Shark® advanced cyclonic action will sweep the metal screen clean once you begin to refill your dust cup.

Proper Care of Your Shark® Upright Vacuum

Proper Care of Your Shark

DO NOT operate the vacuum without ALL the filters in place.
DO NOT operate the vacuum with WET filters.

IMPORTANT: Loss of Suction may occur if foam filters are not cleaned every month. Rinse and allow to air dry completely. Tap loose dirt from foam filters as needed in between washing. Foam filters may appear dirty after use – this is normal.

To clean the pre-motor filters

To clean the pre-motor filters:
1. Remove the dust cup.
2. Pull the filter frame with the pre-motor filters out from the top of the motor base.
3. Remove the filters from the filter frame and tap the loose dirt from the foam filters in between washing as needed.
4. Rinse the filters thoroughly in lukewarm water until the water runs clear. DO NOT put the filters in the washing machine or dishwasher.

NOTE: The material in the filters will discolor over time. This is NORMAL and will not affect the performance of the filters.
5. Squeeze out excess water and let air-dry for at least 24 hours before replacing. Do not use a hair dryer or other heating methods to dry.
6. Place the felt filter in first, then the foam filter.
7. Replace the dust cup.

To clean the post-motor filter

To clean the post-motor filter:
1 Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum.
2 Take out the filter by pulling it straight out.
3 Turn the filter over so that the dirty side is on the bottom and vigorously tap it clean against a garbage can to remove any dust.
4 Wash the filter under the tap using lukewarm water with the dirty side face down until the water runs clear. DO NOT put the filter in the washing machine or dishwasher.

NOTE: The material in the filter will discolor over time. This is NORMAL and will not affect the performance of the filter.
5. Allow the filter to air dry for 24 hours. Do not use a hair dryer or other heating methods to dry.
6. Once the filter is dry, replace it back into the vacuum.
7. Replace the cover by inserting the two tabs into the holes at the bottom and then swinging the cover up until it clicks into place.

Troubleshooting
WARNING: To reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/troubleshooting checks.

1. Vacuum is not picking up dirt:
Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance” sections for instructions.)
Dust cup may be full; empty dust cup.
Check hose and hose connections for blockages; clear blockages if required.
If dust cup is empty, and attachment inlets are clear, check for other blockages. (See “Checking for Blockages” for instructions.)

2. Vacuum lifts scatter rugs (lightweight, movable rugs).
Suction is powerful. Take care when vacuuming scatter-type rugs or rugs with delicately sewn edges. Open the suction release on the hose to decrease suction power.

3.Airflow is restricted. No suction or light suction.
Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance” sections for instructions.)
Dust cup may be full; empty dust cup.
Check hose, hose connections, nozzles and accessories for blockages; clear blockages if required.
Close the suction release on the hose to increase suction power.
If dust cup is empty, and attachment inlets are clear, check for other blockages. (See “Checking for Blockages” for instructions.)

4. Motorized floor brush has become jammed or has shut off.
Immediately turn off and unplug vacuum, disconnect the nozzle and remove blockage before reconnecting and turning vacuum back on. (See “Checking for Blockages” for instructions.)

5. Vacuum turns off on its own.
This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum overheats, the thermostat will automatically turn the unit off. Should this occur, perform the following steps to restart the motor thermostat:
1. Move the On/Off switch to the “O” (Off) position.
2. Unplug the vacuum.
3. Empty the dust cup and clean filters. (See “Maintenance” sections for instructions.)
4. Check for blockages in hose, accessories and inlet openings. (See “Checking for Blockages” for instructions.)
5. Allow the unit to cool for a minimum of 45 minutes.
6. Plug in the vacuum.
7. Turn the On/Off switch to the “I” (On) position to restart the vacuum.
Note: If vacuum still does not start, contact Customer Service at:
1-800-798-7398.

Checking for Blockages
Blockages may cause your vacuum to overheat and shut down. If so, clear the blockages, then follow the instructions for Resetting the
Motor Thermostat on page 12.
WARNING: Never insert sharp objects into any opening to clear an obstruction.
IMPORTANT: Damages caused while clearing or attempting to clear blockages are not covered under your product’s limited warranty.
Unplug the vacuum before checking for blockages.

POLARIZED PLUG

Reassemble all parts securely before operating vacuum.

Checking for Blockages

1 Dust Cup Air Duct:
Stand v
acuum into upright
position.
Remove Dust Cup
Assembly and empty Dust Cup if necessary.
Disconnect the Super Stretch Hose.
Check
Air Duct behind Dust Cup for clogs; clear before replacing Dust Cup Assembly.
2 Intake Opening behind the Brush Roll:
Lay the v
acuum flflat to expose Brush Roll.
Check opening behind the Brush Roll for clogs.
Clear the opening.
Clear the Brush Roll;
use scissors to carefully cut away threads, hair or other debris that might be trapped in the bristles.

Motorized Floor Brush Hose

3 Motorized Floor Brush Hose Connector:
Lay vacuum flflat.
Remove Nozzle Hose and check for clogs.
Push the Hose Connector back onto the Motorized Floor Brush.
4 Hose:
Stand vacuum upright.
Remove hose from both the unit and Cleaning Wand ends.
Inspect both ends and the length of the hose for clogs.
Return the hose to the unit

Questions about your Shark NV42 Vacuum Cleaner Manual ? Post in the comments!
Download Shark NV42 Vacuum Cleaner Manual Manual [PDF]

ProForm 730CS User Manual

ProForm 730CS User Manual

ProForm 730CS User Manual

Model No. 831.299270
Serial No.
Find the serial number in the location shown below. Write the serial number in the space above for reference.

Helpline

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and information before operating the treadmill.

1. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at least eight feet of clearance behind it. Do not place the treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
4. Keep the treadmill indoors, away from moisture
and dust. Do not put the treadmill in a garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol products are used or where oxygen is being administered.
6. Keep children under the age of 12 and pets away from the treadmill at all times.
7. The treadmill should not be used by persons weighing more than 250 pounds.
8. Never allow more than one person on the treadmill at a time.
9. Wear appropriate exercise clothing when using the treadmill. Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet,wearing only stockings, or in sandals.
10. When connecting the power cord (see page 8), plug the power cord into a surge suppressor (not included) and plug the surge suppressor into a grounded circuit capable of carrying 15 or more amps. No other appliance should be on the same circuit. Do not use an extension cord.
11. Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. To purchase a surge suppressor, see your local PROFORM dealer or call 1-800-366- 7278 and order part number 14657.
12. Keep the power cord and the surge suppressor away from heated surfaces.
13. Never move the walking belt while the power is turned off. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is not working properly. (See BEFORE YOU BEGIN on page 5 if the treadmill is not working properly.)
14. Never start the treadmill while you are standing on the walking belt. Always hold the handrails while using the treadmill.
15. The treadmill is capable of high speeds. Adjust the speed in small increments to avoid sudden jumps in speed.
16. The pulse sensor is not a medical device. Various factors, including the user’s movement, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general.
17. Never leave the treadmill unattended while it is running. Always remove the key, unplug the power cord and move the on/off switch to the off position when the treadmill is not in use. (See the drawing on page 5 for the location of the on/off switch.)
18. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 19.) You must be able to safely lift 45 pounds (20 kg) in order to raise, lower, or move the treadmill.
19. Do not change the incline of the treadmill by placing objects under the treadmill.
20. When folding or moving the treadmill, make sure that the storage latch is fully closed.

21. When using i-Fit.com CDÕs and videos, an electronic ÒchirpingÓ sound will alert you when the speed and/or incline of the treadmill is about to change. Always listen for the ÒchirpÓ and be prepared for speed and/or incline changes. In some instances, the speed and/or incline may change before the personal trainer describes the change.
22. When using i-Fit.com CDÕs and videos, you can manually override the speed and incline settings at any time by pressing the speed and incline buttons. However, when the next ÒchirpÓ is heard, the speed and/or incline will change to the next settings of the CD or video program.
23. Always remove i-Fit.com CDÕs and videos from your CD player or VCR when you are not using them.
24. Inspect and tighten all parts of the treadmill regularly.
25. Never insert or drop any object into any opening.
26.DANGER: Always unplug the power cord immediately after use, before cleaning the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the procedures in this manual should be performed by an authorized service representative only.
27. This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. SEARS assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decals shown below have been placed on your treadmill. If a decal is missing, or if it is not legible, please call our toll-free HELPLINE to order a free replacement decal (see the front cover of this manual). Apply the decal in the location shown.

BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM¨ 730CS treadmill. The 730CS treadmill combines advanced technology with innovative design to help you get the most from your exercise program in the convenience and privacy of your home. And when youÕre not exercising, the unique 730CS can be folded up, requiring less than half the floor space of other treadmills.

For your benefit, read this manual carefully before using the treadmill. If you have additional questions, please call our toll-free HELPLINE at 1-800-736-6879,

Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is 831.299270. The serial number can be found on a decal attached to the treadmill (see the front cover of this manual for the location).

Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.

Parts

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver .
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.

1. With the help of a second person, carefully raise the treadmill to the upright position.

While a second person tips the treadmill to one side and holds it, insert one of the Extension Legs (103) into the treadmill as shown. Make sure that the Extension Leg is turned so the Base Pad (97) is on the bottom.

Next, tip the treadmill to the other side and insert the other Extension Leg (not shown) in the same way. Lower the side of the treadmill so that both Extension Legs (103) are resting flat on the floor.

Assembly requires two people.

2. With the help of a second person, carefully tip the Uprights (82) down as shown. Make sure that the Extension Legs (103) remain in the Uprights.

Attach each Extension Leg (103) with two Screws (101) and a Base Pad (122) as shown. With the help of a second person, carefully tip the Uprights (82) back to the vertical position.

Note: One replacement Thick Base Pad (97) may be included. Use the extra Pad if one becomes worn or needs to be replaced.

help of a second person

3. Locate the plastic tie in the post on the left Upright (82). Hold a Handrail Extension (85) in the position shown.

Insert the plastic tie into the Handrail Extension as you insert the Handrail Extension into the post. Attach the Handrail Extension with three Screws (76). The plastic tie is tied to the Pulse Wire (124). Be careful to avoid damaging the Pulse Wire. The Pulse Wire is used with the optional chest pulse sensor (see page 18).

Slide a Handrail Foam Grip (110) onto the Handrail Extension (85). Press two Plastic Fasteners (47) into the Handrail Foam Grip.

Attach the other Handrail Extension and Handrail Foam Grip to the right Upright (not shown). Note: There is not a pulse wire in the right Upright.

 Locate the plastic tie

4. Make sure that the Lock Knob Sleeve (111) is fully inserted into the left Upright (82). Remove the Lock Knob (102) from the Lock Pin (115).

Make sure that the Lock Pin Collar (113) and the Spring (112) are on the Lock Pin. Insert the Lock Pin into the left Upright (82) and tighten the Lock Knob onto it.

Make sure that the Lock Knob Sleeve

5. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 21). To protect the floor or carpet from damage, place a mat under the treadmill.

OPERATION AND ADJUSTMENT

THE PERFORMANT LUBETM WALKING BELT
Your treadmill features a walking belt coated with PERFORMANT LUBETM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD
DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the productÑif it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill (see drawing 1 at the right).

To purchase a surge suppressor, see your local PROFORM dealer or call toll-free 1-800-366-7278 and order part number 14657. Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.

This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available.

grounded outlet

The temporary adapter should be used only until a properly grounded outlet (drawing 1) can be installed by a qualified electrician.

The green-colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover.

Whenever the adapter is used it must be held in place by a metal screw. Some 2-pole receptacle outlet box covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is grounded before using an adapter.

CONSOLE DIAGRAM

CAUTION: Before operating the console, read the following precautions.
¥ Do not stand on the walking belt when turning on the power.
¥ Always wear the clip (see the drawing above) while operating the treadmill.
¥ Adjust the speed in small increments to avoid sudden jumps in speed.
¥ To reduce the possibility of electric shock, keep the console dry. Avoid spilling liquids on the console and place only a sealed water bottle in the water bottle holder.

FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of features to help you get the most from your exercise. When the console is in the manual mode, the speed and incline of the treadmill can be controlled with a touch of a button. As you exercise, the LED track and the four displays will provide continuous exercise feedback. You can even measure your heart rate using the built-in pulse sensor.

Six certified personal trainer programs are also offered. Each program automatically controls the speed and incline of the treadmill as it guides you through an effective workout.

The console also features advanced iFit.com interactive technology. IFit.com technology is like having a personal trainer right in your home. Using the included audio cable, you can connect the treadmill to your

home stereo, portable stereo, or computer and play special iFit.com CD programs (CDÕs are not included). IFit.com CD programs automatically control the speed and incline of the treadmill as a personal trainer guides you through every step of your workout. High-energy music provides added motivation. Each CD features two different programs designed by certified personal trainers.

In addition, you can connect the treadmill to your VCR and TV and play iFit.com video programs (videocassettes are not included). Video programs offer the same benefits as iFit.com CD programs, but add the excitement of working out with a class and an instructor Ñthe hottest new trend at health clubs.

With the treadmill connected to your computer, you can also go to our new internet site at www.iFit.com and access even more programs. Choose from a selection of basic programs that interactively control the speed and incline of your treadmill to help you achieve your personal exercise goals. Or, use iFit.com audio and video programs directly from our internet site. Visit www.iFit.com for complete details.

By adding an optional upgrade module to the treadmill, you can use virtually endless features from our internet site. See www.iFit.com to learn about other iFit.com features. To purchase iFit.com CDÕs, iFit.com videocassettes, or an optional upgrade module, see your local PROFORM dealer or call toll-free 1-800-735- 0768. For information about other optional accessories, see page 18.

To use the manual mode of the console, follow the steps beginning on page 10. To use a personal trainer program, see page 12. To use iFit.com CD or video programs, refer to page 15. To use iFit.com programs directly from our internet site, see page 17.

STEP-BY-STEP CONSOLE OPERATION
Make sure that the on/off switch near the power cord is in the on position. Next, make sure that the key is removed from the console and the power cord is properly plugged in (see HOW TO PLUG IN THE POWER CORD on page 8).

When you are ready to begin exercising, step onto the foot rails of the treadmill. Find the clip attached to the key (see the drawing on page 9), and slide the clip onto the waistband of your clothing.

To use the manual mode of the console, follow the steps below. To use a personal trainer program, see page 12. To use iFit.com CD or video programs, refer to page 15. To use iFit.com programs directly from our internet site, see page 17.

Note: The console can display speed and distance in either miles or kilometers (see SPEED/MIN-MILE DISPLAY on page 11). For simplicity, all instructions in this manual refer to miles.

HOW TO USE THE MANUAL MODE

HOW TO USE THE MANUAL MODE

exercise, change the speed of the walking belt as desired by pressing the SPEED buttons. To stop the walking belt, press the STOP button. The TIME/INCLINE/SEG TIME display will begin to flash. To restart the walking belt, press the START button or the SPEED s button.

Change the incline

DISTANCE

CALS

Measure your pulse

When you are finished using the treadmill, move the on/off switch near the power cord to the off position.

HOW TO USE PERSONAL TRAINER PROGRAMS
HOW TO USE PERSONAL TRAINER PROGRAMS

Press the START button

One speed setting and one incline setting are programmed for each segment. When only three seconds remain in the first segment, a series of tones will sound and the treadmill will automatically adjust to the speed and incline settings for the second segment.

The program will continue in this way until the TIME/INCLINE/SEG TIME display counts down to zero. The walking belt will then slow to a stop.

If the speed or incline setting for the current segment is too high or too low, you can manually override the settings by pressing the SPEED or INCLINE buttons on the console. However, when the next segment begins, the treadmill will adjust to the next speed and incline settings of the program.

To stop the program, press the STOP button. The TIME/INCLINE/SEG TIME display will begin to flash. To restart the program, press the START button or the SPEED s button. To end the program, press the STOP button, remove the key, and then reinsert the key.

Follow your progress

HOW TO CONNECT THE TREADMILL TO YOUR CD PLAYER, VCR, OR COMPUTER

To use iFit.com CDÕs, the treadmill must be connected to your portable CD player, portable stereo, home stereo, or computer with CD player. See pages 13 and 14 for connecting instructions. To use iFit.com videocassettes, the treadmill must be connected to your VCR. See page 15 for connecting instructions. To use iFit.com programs directly from our internet site, the treadmill must be connected to your home computer. See page 14 for connecting instructions.

HOW TO CONNECT YOUR PORTABLE CD PLAYER

Note: If your CD player has separate LINE OUT and PHONES jacks, see instruction A below. If your CD player has only one jack, see instruction B.

A. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into the LINE OUT jack on your CD player. Plug your headphones into the PHONES jack.

HOW TO CONNECT

B. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into a 3.5mm Y-adapter (available at electronics stores). Plug the Y-adapter into the PHONES jack on your CD player. Plug your headphones into the other side of the Y-adapter.

audio cable

HOW TO CONNECT YOUR PORTABLE STEREO

Note: If your stereo has an RCA-type AUDIO OUT jack, see instruction A below. If your stereo has a 3.5mm LINE OUT jack, see instruction B. If your stereo has only a PHONES jack, see instruction C.

A. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into the included adapter. Plug the adapter into an AUDIO OUT jack on your stereo.

AUDIO OUT jack

B. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into the LINE OUT jack on your stereo.

Plug one end of the audio cable

C. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into a 3.5mm Y-adapter (available at electronics stores). Plug the Y-adapter into the PHONES jack on your stereo. Plug your headphones into the other side of the Y-adapter.

Plug one end of the audio cable

HOW TO CONNECT YOUR HOME STEREO
Note: If your stereo has an unused LINE OUT jack, see instruction A below. If the LINE OUT jack is being used, see instruction B.

A. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into the included adapter. Plug the adapter into the LINE OUT jack on your stereo.

HOW TO CONNECT YOUR HOME STEREO

B. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into the included adapter. Plug the adapter into an RCA adapter (available at electronics stores). Next, remove the wire that is currently plugged into the LINE OUT jack on your stereo and plug the wire into the unused side of the RCA adapter. Plug the RCA adapter into the LINE OUT jack on your stereo.

LINE OUT jack on

HOW TO CONNECT YOUR COMPUTER

Note: If your computer has a 3.5mm LINE OUT jack, see instruction A. If your computer has only a PHONES jack, see instruction B.

A. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into the LINE OUT jack on your computer.

HOW TO CONNECT YOUR COMPUTER

B. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into a 3.5mm Y-adapter (available at electronics stores). Plug the Y-adapter into the PHONES jack on your computer. Plug your headphones or speakers into the other side of the Y-adapter.

Plug one end of the audio cable

HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack, see instruction A below. If the AUDIO OUT jack is being used, see instruction B. If you have a TV with a built-in VCR, see instruction B. If your VCR is connected to your home stereo, see HOW TO CONNECT YOUR HOME STEREO on page 14.

A. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into the included adapter. Plug the adapter into the AUDIO OUT jack on your VCR.

HOW TO CONNECT YOUR VCR

B. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Plug the other end of the cable into the included adapter. Plug the adapter into an RCA adapter (available at electronics stores). Next, remove the wire that is currently plugged into the AUDIO OUT jack on your VCR and plug the wire into the unused side of the RCA adapter. Plug the RCA adapter into the AUDIO OUT jack on your VCR.

OUT jack on your VCR

HOW TO USE IFIT.COM CD AND VIDEO PROGRAMS
To use iFit.com CDÕs or videocassettes, the treadmill must be connected to your portable CD player, portable stereo, home stereo, computer with CD player, or VCR. See HOW TO CONNECT THE COMPUTER TO YOUR CD PLAYER, VCR, OR COMPUTER on page 13. Note: To purchase iFit.com CDÕs or iFit.com videocassettes, see your local PROFORM dealer or call toll-free 1-800-735-0768.

Make sure that the on/off switch near the power cord is in the on position. In addition, make sure that the power cord is properly plugged in (see HOW TO PLUG IN THE POWER CORD on page 8).

When you are ready to begin exercising, step onto the foot rails of the treadmill. Find the clip attached to the key (see the drawing on page 9), and slide the clip onto the waistband of your clothing. Follow the steps below to use an iFit.com CD or video. Note: The instructions included in the CD case describe how to use the CD with a variety of PROFORM treadmills. Some instructions may not apply to this treadmill.

instructions included in the CD

4. Press the PLAY button on your CD player or VCR.
A moment after the button is pressed, your personal trainer will begin guiding you through your workout. Simply follow your personal trainerÕs instructions.

During the CD or video program, an electronic ÒchirpingÓ sound will alert you when the speed and/or incline of the treadmill is about to change.

CAUTION: Always listen for the ÒchirpÓ and be prepared for speed and/or incline changes. In some instances, the speed and/or incline may change before the personal trainer describes the change.

If the speed or incline settings are too high or too low, you can manually override the settings at any time by pressing the SPEED or INCLINE buttons on the console. However, when the next ÒchirpÓ is heard, the speed and/or incline will change to the next settings of the CD or video program.

To stop the program at any time, press the START/STOP button on the console. The TIME/MIN-MILE display will begin to flash. To restart the program, press the START/STOP button again. After a moment, the walking belt will begin to move at 1 mph. When the next ÒchirpÓ is heard, the speed and incline will change to the next settings of the CD or video program. The program can also be stopped by pressing the STOP button on your CD player or VCR.

When the CD or video program is completed, the walking belt will stop and the TIME/MIN-MILE display will begin to flash. Note: To use another CD or video program, press the START/STOP button or remove the key and go to step 1 on page 15. Note: If the speed or incline of the treadmill does not change when a ÒchirpÓ is heard:
1. make sure that the iFit.com indicator is lit and that the TIME/MIN-MILE display is not flashing
2. adjust the volume of your CD player or VCR. If the volume is too high or too low, the console may not detect the program signals
3. make sure that the audio cable is properly connected, that it is fully plugged in, and that it is not wrapped around a power cord
3. if you are using your portable CD player and the CD skips, set the CD player on the floor or another flat surface instead of on the console.

5. Follow your progress with the LED track and the four displays.
See step 5 on page 10.

6. Measure your pulse, if desired.
See step 6 on page 11.

7. When the iFit.com CD or video program is finished, remove the key.

Step onto the foot rails and remove the key from the console. Keep the key in a secure place.

Note: If the displays and various indicators on the console remain lit after the key is removed, the console is in the ÒdemoÓ mode. Refer to page 18 and turn off the demo mode.

CAUTION: Always remove iFit.com CDÕs and videocassettes from your CD player or VCR when you are finished using them.

When you are finished using the treadmill, move the on/off switch near the power cord to the off position.

HOW TO USE PROGRAMS DIRECTLY FROM OUR INTERNET SITE

Our new internet site at www.iFit.com allows you to access a large selection of programs that interactively control your treadmill to help you achieve your specific exercise goals. In addition, you can play iFit.com audio and video programs directly from the internet. By adding an optional upgrade module to the console, you can use virtually endless features on our internet site. Explore www.iFit.com for details. To purchase an upgrade module, call toll-free 1-800-735-0768.

To use programs from our internet site, the treadmill must be connected to your home computer. See HOW TO CONNECT YOUR COMPUTER on page 14. In addition, you must have at least a 56K modem and an account with an internet service provider. A list of additional system and software requirements will be found on our internet site.

Next, make sure that the on/off switch near the power cord is in the on position.

In addition, make sure that the power cord is properly plugged in (see HOW TO PLUG IN THE POWER CORD on page 8). Follow the steps below to use a program from our internet site.

Follow the steps below

4. Follow the desired links on our internet site to select a program.

5. Read and follow the on-line instructions for using a
program.

6. Follow the on-line instructions to start the program.

When you start the program, an on-screen countdown will begin.

7. Return to the treadmill and stand on the foot rails. Find the clip attached to the key and slide the key onto the waistband of your clothing.
When the on-screen countdown ends, the program will begin and the walking belt will begin to move. Hold the handrails, step onto the walking belt, and begin walking.

During the program, an electronic ÒchirpingÓ sound will alert you when the speed and/or incline of the treadmill is about to change. CAUTION: Always listen for the ÒchirpÓ and be prepared for speed and/or incline changes.

If the speed or incline settings are too high or too low, you can manually override the settings at any time by pressing the SPEED or INCLINE buttons on the console. However, when the next ÒchirpÓ is heard, the speed and/or incline will change to the next settings of the program.

To stop the program at any time, press the STOP button on the console. The TIME/INCLINE display will begin to flash. To restart the program, press the START button. After a moment, the walking belt will begin to move at 1.0 mph. When the next ÒchirpÓ is heard, the speed and incline will change to the next settings of the program.

When the program is completed, the walking belt will stop and the TIME/INCLINE display will begin to flash. Note: To use another program, press the STOP button and go to step 5 above.

Note: If the speed or incline of the treadmill does not change when a ÒchirpÓ is heard, make sure that the iFit.com indicator is lit and that the TIME/INCLINE display is not flashing. In addition, make sure that the audio cable is properly connected, that it is fully plugged in, and that it is not wrapped around a power cord.

8. Follow your progress with the LED track and the four displays.
See step 5 on page 10.

9. Measure your pulse, if desired. See step 6 on page 11.

10.When the program is finished, remove the key.

Step onto the foot rails and remove the key from the console. Keep the key in a secure place. Note: If the displays and various indicators on the console remain lit after the key is removed, the console is in the ÒdemoÓ mode. Refer to the instructions at the right and turn off the demo mode.
When you are finished using the treadmill, move the on/off switch near the power cord to the off position.

THE INFORMATION MODE/DEMO MODE
The console features an information mode that keeps track of the total number of hours that the treadmill has been operated and the total number of miles that the walking belt has moved. The information mode also allows you to switch the console from miles per hour to kilometers per hour. In addition, the information mode allows you to turn on and turn off the demo mode.

To select the information mode, hold down the STOP button while inserting the key into the console. When the information mode is selected, the following information will be shown:

The DISTANCE

IMPORTANT

To exit the information mode, remove the key from the console.

OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor adds even more features to the console. The chest pulse sensor offers hands-free operation and continuously monitors your heart rate during your workouts. To purchase the optional chest pulse sensor, call the toll-free telephone number listed on the back cover of this manual.

OPTIONAL CHEST PULSE SENSOR

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the lowest position. If this is not done, the treadmill may be permanently damaged. Next, unplug the power cord.

CAUTION: You must be able to safely lift 45 pounds (20 kg) in order to raise, lower, or move the treadmill.

1. Hold the treadmill with your hands in the locations shown at the right. CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back. Raise the treadmill about halfway to the vertical position.

2. Move your right hand to the position shown and hold the treadmill firmly. Using your left hand, pull the latch knob to the left and hold it. Raise the treadmill until the latch pin is aligned with the hole in the catch. Insert the latch pin into the catch. Make sure that the latch pin is fully inserted into the catch.

To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85¡ Fahrenheit.

HOW TO FOLD THE TREADMILL FOR STORAGE

HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the latch
pin is fully inserted into the catch.

1. Hold the handrails as shown and place one foot against a wheel.

2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not attempt to move the treadmill over an uneven surface.

3. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position.

HOW TO LOWER THE TREADMILL FOR USE
1. Refer to drawing 2 above. Hold the treadmill with your right hand as shown. Using your left hand, pull the latch knob to the left and hold it. Pivot the treadmill down until the frame is past the pin. Slowly release the latch knob.

2. Refer to drawing 1. Hold the treadmill firmly with both hands, and lower the treadmill to the floor.

CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.

HOW TO MOVE THE TREADMILL

TROUBLE-SHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. See step 1 on page 10.

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on position.

The power does not turn on

PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 10.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, please call our toll-free HELPLINE.

PROBLEM: The speed display on the console does not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the screws from the hood and carefully remove the hood. Locate the Reed Switch (21) and the Magnet (43) on the left side of the Pulley (42). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8Ó. If necessary, loosen the Reed Switch Screw (76) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.
The speed display

PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in length.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, please call our toll-free HELPLINE.

Rear Roller Adjustment Bolts

PROBLEM: The walking belt is off-center
SOLUTION: a. If the walking belt has shifted to the left, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn the left rear roller adjustment bolt
clockwise, and the right bolt counterclockwise, 1/4 of a
turn each. Be careful not to overtighten the walking belt.
Plug in the power cord, insert the key and run the treadmill
for a few minutes. Repeat until the walking belt is
centered.
b. If the walking belt has shifted to the right, first remove
the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjustment
bolt counterclockwise, and the right bolt clockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key and
run the treadmill for a few minutes. Repeat until the
walking belt is centered.

PROBLEM: The walking belt slips when walked on
SOLUTION: a. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and carefully walk on the treadmill for a few minutes. Repeat until the walking be lt is properly tightened.

PROBLEM: The incline of the treadmill does not change correctly or does not change when i-Fit.com CDÕs and videos are played
SOLUTION: a. With the key inserted in the console, press one of the INCLINE buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline.

The walking belt is off-center

CONDITIONING GUIDELINES
WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.

The pulse sensor is not a medical device. Various factors, including your movement, may affect the accuracy of heart rate readings. The sensor is intended only as an exercise aid in determining heart rate trends in general.

The following guidelines will help you to plan your exercise program. RememberÑthese are general guidelines only. For more detailed exercise information, obtain a reputable book or consult your physician.

EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your cardiovascular system, the key to achieving the desired results is to exercise with the proper intensity. The proper intensity level can be found by using your heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.

EXERCISE INTENSITY

To find the proper heart rate for you, first find your age near the bottom of the chart (ages are rounded off to the nearest ten years). Next, find the three numbers above your age. The three numbers define your Òtraining zone.Ó The lower two numbers are recommended heart rates for fat burning; the higher number is the recommended heart rate for aerobic exercise. To measure your heart rate during exercise, use the pulse sensor on the console. If your heart rate is too high or too low, adjust the speed and incline of the treadmill.

Fat Burning
To burn fat effectively, you must exercise at a relatively low intensity level for a sustained period of time. During the first few minutes of exercise, your body

uses easily accessible carbohydrate calories for energy.
Only after the first few minutes does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in your training zone.For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.

Aerobic Exercise
If your goal is to strengthen your cardiovascular system,
your exercise must be Òaerobic.Ó Aerobic exercise is activity that requires large amounts of oxygen for prolonged periods of time. This increases the demand on the heart to pump blood to the muscles, and on the lungs to oxygenate the blood. For aerobic exercise, adjust the speed and incline of the treadmill until your heart rate is near the highest number in your training zone.

WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-upÑStart each workout with 5 to 10 minutes of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.

Training Zone ExerciseÑAfter warming up, increase the intensity of your exercise until your pulse is in your training zone for 20 to 60 minutes. (During the first few weeks of your exercise program, do not keep your pulse in your training zone for longer than 20 minutes.) Breathe regularly and deeply as you exerciseÑnever hold your breath.

A Cool-downÑFinish each workout with 5 to 10 minutes of stretching to cool down. This will increase the flexibility of your muscles and will help prevent post-exercise problems.

Exercise Frequency
To maintain or improve your condition, complete three workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key to success is to make exercise a regular and enjoyable part of your everyday life.

EXPLODED DRAWING

EXPLODED DRAWINGÑMode

The model number and serial number of your PROFORM¨ 730CS
treadmill are listed on a decal attached to the frame. See the front cover of this manual to find the location of the decal. All replacement parts are available for immediate purchase or special order when you visit your nearest SEARS Service Center. To request service or to order parts by telephone, call the toll-free numbers listed at the left.

When requesting help or service, or ordering parts, please be prepared to provide the following information:
1. The NAME OF THE PRODUCT (PROFORM¨ 730CS treadmill)
2. The MODEL NUMBER OF THE PRODUCT (831.299270)
3. The KEY NUMBER AND DESCRIPTION OF THE PART (see the EXPLODED DRAWING in the center of this manual and the PART LIST on page 23).

Model No. 831.299270 QUESTIONS?
If you find that:
1. you need help assembling or operating the PROFORM 730CS treadmill
2. a part is missing
3. or you need to schedule repair service
call our toll-free HELPLINE
1-800-736-6879
MondayÐSaturday, 7 amÐ7 pm
Central Time (excluding holidays)
REPLACEMENT
PARTS

If parts become worn and need
to be replaced, call the following
toll-free number
1-800-FON-PART
(1-800-366-7278)

FULL 90 DAY WARRANTY

For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this SEARS TREADMILL EXERCISER, contact the nearest SEARS Service Center throughout the United States and SEARS will repair or replace the TREADMILL EXERCISER, free of charge.
This warranty does not apply when the TREADMILL EXERCISER is used commercially or for rental purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179

Panasonic D-Tech 6.0 Manual KX-TG78XX Phones

Operating Instructions

Panasonic D-Tech 6.0 Manual KX-TG78XX Phones

Model composition
Model composition

*1 Single handset models: Intercom calls can be made between handsets by purchasing and registering one or more optional handsets (page 5).
*2 The following features are provided for these models:
– USB charging (USB jack is on the left side of the base unit)
– Text message alert feature

Accessory information
Accessory information

Introduction

Introduction

1 Replacement batteries may have a different capacity from that of the supplied batteries.

*2 By installing this unit, you can extend the range of your phone system to include areas where reception was previously not available. This product can be purchased online. Please visit our Web site: http://www.panasonic.com/RangeExtender

*3 By registering the key detector (4 max.) to a Panasonic Digital Cordless Phone and attaching it to an easy-to-lose item in advance, you can locate and find the mislaid item to which the key detector is attached. Please visit our Web site:http://panasonic.net/pcc/products/telephone/p/tga20/

Expanding your phone system

Expanding your phone system

*1 Your cellular phone and headset must be Bluetooth wireless technology compatible. For more details and the list of compatible cellular phones, please visit our Web site: http://www.panasonic.com/link2cell

Trademarks
R The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is under license. All other trademarks identified herein are the property of their respective owners.

For your safety
To prevent severe injury and loss of life/
property, read this section carefully before
using the product to ensure proper and safe
operation of your product.

WARNING
Power connection

R Use only the power source marked on the product.
R Do not overload power outlets and extension cords. This can result in the risk
of fire or electric shock.
R Completely insert the AC adaptor/power
plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire.
R Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from
the power outlet, then wiping with a dry cloth. Accumulated dust may cause an
insulation defect from moisture, etc.
resulting in a fire.
R Unplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact the Panasonic Call Center at
1-800-211-PANA (1-800-211-7262).
R Unplug from power outlets and never touch the inside of the product if its casing has been broken open.
R Never touch the plug with wet hands.
Danger of electric shock exists.

Installation R To prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture.

R Do not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an

R Do not allow the AC adaptor or telephone line cord to be excessively pulled, bent or placed under heavy objects.

Operating safeguards

R Unplug the product from power outlets before cleaning. Do not use liquid or
aerosol cleaners.
R Do not disassemble the product.
R Do not spill liquids (detergents, cleansers, etc.) onto the telephone line cord plug, or allow it to become wet at all. This may cause a fire. If the telephone line cord plug becomes wet, immediately pull it from the telephone wall jack, and do not use.

Medical
R Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF
(radio frequency) energy. (The product operates in the frequency range of
1.92 GHz to 1.93 GHz, and the RF transmission power is 115 mW (max.).)

R Do not use the product in health care facilities if any regulations posted in the
area instruct you not to do so. Hospitals or health care facilities may be using
equipment that could be sensitive to external RF energy.
CAUTION Installation and location
R Never install telephone wiring during an electrical storm.
R Never install telephone line jacks in wet locations unless the jack is specifically designed for wet locations.
R Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
R Use caution when installing or modifying
telephone lines.
R The AC adaptor is used as the main disconnect device. Ensure that the AC
outlet is installed near the product and is easily accessible.
R This product is unable to make calls when:

– the handset batteries need recharging or have failed.
– there is a power failure.

Battery
R We recommend using the batteries noted on page 4. USE ONLY rechargeable
Ni-MH batteries AAA (R03) size.
R Do not mix old and new batteries.
R Do not open or mutilate the batteries.
Released electrolyte from the batteries is corrosive and may cause burns or injury to the eyes or skin. The electrolyte is toxic and may be harmful if swallowed.
R Exercise care when handling the batteries.

Do not allow conductive materials such as rings, bracelets, or keys to touch the
batteries, otherwise a short circuit may cause the batteries and/or the conductive material to overheat and cause burns.
R Charge the batteries provided with or identified for use with this product only, in accordance with the instructions and limitations specified in this manual.
R Only use a compatible base unit (or charger) to charge the batteries. Do not
tamper with the base unit (or charger). Failure to follow these instructions may
cause the batteries to swell or explode.

Attention:
A nickel metal hydride battery that is recyclable powers the product you have
purchased.
Please call 1-800-8-BATTERY
(1-800-822-8837) for information on how to recycle this battery.

Important safety instructions
When using your product, basic safety precautions should always be followed to
reduce the risk of fire, electric shock, and injury to persons, including the following:
1. Do not use this product near water for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

For best performance
Base unit location/avoiding noise The base unit and other compatible Panasonic
units use radio waves to communicate with each other.
R For maximum coverage and noise-free communications, place your base unit:
– at a convenient, high, and central location with no obstructions between
the handset and base unit in an indoor environment.
– away from electronic appliances such as TVs, radios, personal computers,
wireless devices, or other phones.
– facing away from radio frequency transmitters, such as external antennas
of mobile phone cell stations. (Avoid putting the base unit on a bay window or
near a window.)
R Coverage and voice quality depends on the local environmental conditions.

R If the reception for a base unit location is
not satisfactory, move the base unit to
another location for better reception.

Environment
R Keep the product away from electrical noise
generating devices, such as fluorescent
lamps and motors.
R The product should be kept free from
excessive smoke, dust, high temperature,
and vibration.
R The product should not be exposed to
direct sunlight.
R Do not place heavy objects on top of the
product.
R When you leave the product unused for a
long period of time, unplug the product from
the power outlet.
R The product should be kept away from heat
sources such as heaters, kitchen stoves,
etc. It should not be placed in rooms where
the temperature is less than 0 °C (32 °F) or
greater than 40 °C (104 °F). Damp
basements should also be avoided.
R The maximum calling distance may be
shortened when the product is used in the
following places: Near obstacles such as
hills, tunnels, underground, near metal
objects such as wire fences, etc.
R Operating the product near electrical
appliances may cause interference. Move
away from the electrical appliances.
Routine care
R Wipe the outer surface of the product
with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.

Other information
CAUTION: Risk of explosion if battery is
replaced by an incorrect type. Dispose of used
batteries according to the instructions.

Notice for product disposal, transfer, or return
R This product can store your private/
confidential information. To protect your
privacy/confidentiality, we recommend that
you erase information such as phonebook
or caller list entries from the memory before
you dispose of, transfer, or return the

ENERGY STAR (for KX-TG7841 series)
As an ENERGY STAR® Partner, Panasonic
has determined that this product meets the
ENERGY STAR guidelines for energy
efficiency. ENERGY STAR is a U.S.
registered mark.

Specifications
1. Standard: DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0)
Bluetooth wireless technology 2.0
2. Frequency range: 1.92 GHz to 1.93 GHz (DECT), 2.402 GHz to 2.48 GHz (Bluetooth)
3. RF transmission power: 115 mW (max.)
4. Power source: 120 V AC, 60 Hz
5. Power consumption: Base unit:*1 Standby: Approx. 1.2 W Maximum: Approx. 4.5 W
Base unit:*2 Standby: Approx. 1.2 W Maximum: Approx. 8.5 W Charger: Standby: Approx. 0.1 W Maximum: Approx. 1.8 W
6. USB Charger:*2 Output voltage: DC 5 V Output current: 500 mA
7. Operating conditions: 0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 % relative air humidity (dry) *1 KX-TG7841 series: page 3 *2 KX-TG7871 series: page 3
Note:
8. Design and specifications are subject to change without notice.
9. The illustrations in these instructions may vary slightly from the actual product.

Setting up Connections

1. If you do not connect the telephone line cord and use only cellular lines, set the cellular line only mode to use this unit more conveniently (page 19). n Base unit (KX-TG7841 series: page 3)

2. Use only the supplied Panasonic AC adaptor PNLV226.

Setting Up

*DSL/ADSL filter (not supplied) is required if you have DSL/ADSL service.

1. Base unit (KX-TG7871 series: page 3)
2. Use only the supplied Panasonic AC adaptor PNLV234.
3. The hook of the base unit is not designed to hold the AC adaptor cord for the desk stand or wall mounting use (page 67).
Base unit

Battery installation

Battery charging

Note when setting up

Note for battery charging

Getting Started

Getting Started

Intelligent eco mode

Controls

Controls

1. Speaker
2. M N (TALK)
3. Headset jack
4. Dial keypad (*: TONE)
5. MZN (SP-PHONE: Speakerphone)
6. Microphone
7. Receiver
8. Display
9. MOFFN
10. MFLASHNMCALL WAITN
11. MNOISE REDUCTIONN
12. Charge contacts

Control type

Control type

Base unit

Base unit

Base Unit Mark

Charging the cellular phone by USB
Available for:
KX-TG7871 series (page 3)

By connecting a USB cable (not supplied) to the cellular phone and the base unit, you can charge a cellular phone. However, the cellular phone cannot exchange data with the base unit through a USB cable.

Charging the cellular phone

Display/Indicators

Display/Indicators

Display/Indicators

Initial settings
n Direct command code: Programmable settings can be accessed by pressing MMENUN, #, and then the corresponding code on the dial keypad (page 36).
Example: Press MMENUN#101.
n Symbol meaning:
Example: MbN: “Off”
Press MCN or MDN to select the words in quotations.

Date and time
Important:
R When you install the batteries for the first time, the handset may prompt you to set date and time. First press MSELECTN, then proceed to step 2.

Handset
1 MMENUN#101
2 Enter the current month, date, and year
by selecting 2 digits for each.
Example: July 15, 2013
07 15 13
3 MOKN
4 Enter the current hour and minute
(12-hour clock format) by selecting 2
digits for each.
Example: 9:30
09 30
5 *: Select “AM” or “PM”.
6 MSAVEN a MOFFN

Note:
R When English is selected as the display language, 12-hour clock format is used.
When Spanish is selected, 24-hour clock format is used.
R The date and time may be incorrect after a power failure. In this case, set the date and time again.

Display language
You can select either “English” or “Español” as the display language. The
default setting is “English”.

Handset / Base unit
1 MMENUN#110
2 MbN: Select the desired setting. a MSAVEN
3 Proceed with the operation for your unit.

Handset: MOFFN
Base unit: MEXITN
Voice guidance language You can select either “English” or “Español” as the voice guidance language of the answering system. The defau lt setting is
“English”.

Handset
1 MMENUN#112
2 MbN: Select the desired setting.
3 MSAVEN a MOFFN

Dialing mode
If you cannot make calls, change this setting
according to your telephone line service. The
default setting is “Tone”.
“Tone”: For tone dial service.
“Pulse”: For rotary/pulse dial service.

Handset
1 MMENUN#120
2 MbN: Select the desired setting.
3 MSAVEN a MOFFN

Questions about your Panasonic D-Tech 6.0 Manual KX-TG78XX Phones? Post in the comments!
Download Panasonic D-Tech 6.0 Manual KX-TG78XX Phones Manual [PDF]

Panasonic SC-BTT / SA-BTT Series Manual [BTT770,BTT730,BTT270,BTT273

Blu-ray DiscTM

Panasonic SC-BTT / SA-BTT Series Manual [BTT770,BTT730,BTT270,BTT273

Owner’s Manual
Blu-ray DiscTM Home Theater Sound System

Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
Before connecting, operating or adjusting this product, please read the instructions completely.
Please keep this manual for future reference.

If you have any questions contact
U.S.A. and Puerto Rico : 1-800-211-PANA(7262)
Canada : 1-800-561-5505

THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:To assure continued compliance, follow the attached
installation instructions and use only shielded interface cables when
connecting to peripheral devices. Any changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)

THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
of this device.
Contains FCC ID: RYYWYPAEBUX4
Contains IC:4389B-WYPAEBUX4
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
This product is restricted to indoor use due to its operation in the 5.15 to
5.25 GHz frequency range.

FCC and IC require this product to be used indoors for the frequency range
5.15 to 5.25 GHz to reduce the potential for harmful interference to
co-channel Mobile Satellite systems. High power radars are allocated as
primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage this product.
This equipment complies with FCC/IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC
radio frequency (RF) Exposure rules. This equipment has very low levels of
RF energy that it deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be installed and operated
keeping the radiator at least 20cm or more away from person’s body
(excluding extremities: hands, wrists, feet and ankles).

[BTT770]
THE FOLLOWING APPLIES ONLY IN THE U.S.A.

FCC Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.

However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

≥ Consult the dealer or an experienced radio/TV technician for help.
FCC caution: To maintain compliance with FCC regulations, shielded
interface cables must be used with this equipment. Operation with
non-approved equipment or unshielded cables may result in interference
to radio and TV reception. Any changes or modifications not approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)

WARNING:
To satisfy FCC RF exposure requirements for mobile transmitting devices,
a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not
recommended. The antenna used for this transmitter must not be
co-located in conjunction with any other antenna or transmitter.

[BTT770]
THE FOLLOWING APPLIES ONLY IN CANADA.
This Class B digital apparatus complies with Canadian ICES-003.

[BTT770] [BTT370]
THE FOLLOWING APPLIES ONLY IN CANADA.
For main unit
Product Identification Marking is located on the bottom of the unit.

[BTT770]
For wireless system
Product Identification Marking is located on the bottom of wireless system.

IMPORTANT SAFETY
INSTRUCTIONS

Read these operating instructions carefully before using the unit. Follow the
safety instructions on the unit and the applicable safety instructions listed
below. Keep these operating instructions handy for future reference.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of
the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.

WARNING
Unit
To reduce the risk of fire, electric shock or product damage,
– Do not expose this unit to rain, moisture, dripping or splashing.
– Do not place objects filled with liquids, such as vases, on this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to qualified service
personnel.

CAUTION
Unit
– This unit utilizes a laser. Use of controls or adjustments or performance of
procedures other than those specified herein may result in hazardous
radiation exposure.
– Do not place sources of naked flames, such as lighted candles, on this unit.
Placement
To reduce the risk of fire, electric shock or product damage,
– Do not install or place this unit in a bookcase, built-in cabinet or in another
confined space. Ensure this unit is well ventilated.
– Do not obstruct this unit’s ventilation openings with newspapers,
tablecloths, curtains, and similar items

CAUTION

This Owner’s Manual is applicable to models
SC-BTT770, SC-BTT370, SC-BTT270 and SC-BTT273.
Unless otherwise indicated, illustrations in this Owner’s
Manual are of SC-BTT770.
≥ Operations in this Owner’s Manual are described mainly
with the remote control, but you can perform the
operations on the main unit if the controls are the same.

Indicates features applicable to:
[BTT770]: SC-BTT770 only
[BTT370]: SC-BTT370 only
[BTT270]: SC-BTT270 only
[BTT273]: SC-BTT273 only

System SC-BTT770 SC-BTT370 SC-BTT270 SC-BTT273
Main unit SA-BTT770 SA-BTT370 SA-BTT270 SA-BTT273
Speaker system Front speakers SB-HF775 SB-HF370 SB-HF270 SB-HF370
Center speaker SB-HC775 SB-HC370 SB-HC270 SB-HC370
Surround speakers SB-HS270 SB-HS270 SB-HS270 SB-HS270
Subwoofer SB-HW370 SB-HW370 SB-HW270 SB-HW270
Wireless system (with digital transmitter) SH-FX71

≥ Some accessories and external devices mentioned in this Owner’s Manual that are not included with this product may not be on sale in certain regions.

≥ Please note that the actual controls and components, menu items, etc. of your Blu-ray Disc Home Theater Sound System may look somewhat different from those shown in the illustrations in this Owner’s Manual.

Accessory
Check the supplied accessories before using this unit.
For accessories of speakers, refer to page 10.

[BTT770]

BTT370

[BTT270]

[BTT273]

Control reference guide

Control reference guide

Remote control

1 Turn the unit on and off
2 Select title numbers, etc./Enter numbers or characters
(􀀾 34)
[CANCEL]: Cancel
3 Select the source (􀀾 22)
4 Basic playback control buttons (􀀾 25)
5 Select preset radio stations
6 Show status messages (􀀾 25)
7 Display the Home screen of VIERA CAST (􀀾 34)
8 Selection/OK, Frame-by-frame (􀀾 25)
9 Show sub menu (􀀾 26)
10 These buttons are used when;
≥ Operating a BD-Video disc that includes JavaTM
applications (BD-J).
≥ Operating contents of VIERA CAST (􀀾 34)
11 Set the sound mode (􀀾 24)/Select speaker channel
(􀀾 24)
12 Select surround sound effects (􀀾 24)/Set the sleep timer

1 Press and hold [–SLEEP].
2 While “SLEEP ££” is displayed, press [–SLEEP]
several times to select the time (in minutes).
≥ Timer selection is up to 120 minutes.
≥ Select “OFF” when canceling the setting.
≥ To confirm the remaining time
Press and hold the button again.

13 TV operation buttons
[Í]: Turn the television on and off
[AV, INPUT]: Switch the input select
[i j VOL]: Adjust the volume
14 Adjust the volume of the main unit
15 Mute the sound
≥ “MUTE” flashes on the unit’s display, while the function is
on.
≥ To cancel, press the button again or adjust the volume.
≥ Muting is canceled if the unit is turned off.
16 Show NETFLIX screen
17 Select radio stations manually (􀀾 29)
18 Exit the menu screen
19 Show HOME menu (􀀾 23)
20 Show Pop-up menu/Top menu/Direct Navigator (􀀾 25)
21 Return to previous screen
22 [BTT770] [BTT370] : Start up a video communication (􀀾 34)
23 Show Playback menu (􀀾 35)/Select audio (􀀾 25)

Main unit (Front)
Main unit (Front)

1 Standby/on switch (POWER Í/I) (􀀾 19)
Press to switch the unit from on to standby mode or vice
versa. In standby mode, the unit is still consuming a small
amount of power.
2 Open or close the disc tray (􀀾 22)
3 Adjust the volume of the main unit
4 Disc tray
5 Stop (􀀾 25)

6 Start play (􀀾 25)
7 SD card slot (􀀾 22)
8 Remote control signal sensor
Distance: Within approx. 7 m (23 ft.)
Angle: Approx. 20o up and down, 30o left and right
9 Display
10 Connect iPod/iPhone (􀀾 32)

POWER-SAVING FEATURES
The main unit is designed to conserve its power consumption and save energy.
[BTT770] [BTT370] Wireless system (SH-FX71) does not have this function.

≥ Automatic power-down function
The main unit will automatically switch to standby mode after
30 minutes if the main unit is inactive as follows.

e.g.
jThere is no audio signal from an external device.
jDisc playback is stopped/paused.
jiPod/iPhone playback is stopped/paused.
jThe disc menu is displayed and play is not selected.
(This function may not work depending on the application
type of discs.)

Main unit (Rear) L

Main unit (Rear) R

1 AC IN terminal (􀀾 18)
2 Speaker terminals (􀀾 13)
3 Cooling fan
4 [BTT770] [BTT370] USB port for the Communication Camera
TY-CC10W (optional) (􀀾 34)
5 LAN port (􀀾 17)
6 HDMI AV OUT (ARC) terminal (􀀾 15)
7 [BTT770] [BTT370] HDMI 1 IN (CABLE/SAT) terminal (􀀾 16)
8 [BTT770] [BTT370] HDMI 2 IN terminal (􀀾 16)

9 FM radio antenna terminal (􀀾 16)
10 DIGITAL AUDIO IN terminal (􀀾 14 , 15)
11 AUX terminal (􀀾 14)
12 VIDEO OUT terminal (􀀾 14)
13 [BTT770] Digital transmitter dock for supplied wireless
system (􀀾 17)
[BTT370] Digital transmitter dock for optional wireless
system (􀀾 12)

Playable discs/Cards

Playable discs/Cards

Discs that cannot be played in this unit
Any other disc that is not specifically supported or
previously described.
1. DVD-RAM
2. Super Audio CD
3. Photo CD
4. DVD-Audio
5. Video CD and Super Video CD
6. WMA discs
7. DivX discs
8. PAL discs
9. HD DVD
10 BD-Video discs recorded at a rate of 50 fields/sec

Region management information
BD-Video

This unit plays BD-Video marked with labels containing the
region code “A”.
Example:

BD-Video

DVD-Video
This unit plays DVD-Video marked with labels containing the
region number “1” or “ALL”.
Example:

DVD-Video

Finalize
DVD-R/RW/R DL, +R/+RW/+R DL and CD-R/RW recorded by
a recorder, etc. needs to be finalized by the recorder to play on
this unit. Please refer to the recorder’s instructions.
BD-Video
This unit supports high bit rate audio (Dolby Digital Plus, Dolby
TrueHD, DTS-HD High Resolution Audio and DTS-HD Master
Audio) adopted in BD-Video.
Music CD
≥ Operation and sound quality of CDs that do not conform to
CD-DA specifications (copy control CDs, etc.) cannot be
guaranteed.
≥ The digital audio content side of a DualDisc does not meet
the technical specifications of the Compact Disc Digital
Audio (CD-DA) format so playback may not be possible.
3D
≥ 3D videos and 3D still pictures can be played back when this
unit is connected to a 3D compatible TV using a High Speed
HDMI Cable.
≥ 2D video can be enjoyed as 3D virtually. (􀀾 27)

Unit and media care
Unit and media care

SD card

Using the remote control

Using the remote control

Questions about your panasonic SC-BTT / SA-BTT Series Manual [BTT770,BTT730,BTT270,BTT273]? Post in the comments!
Download panasonic SC-BTT / SA-BTT Series Manual [BTT770,BTT730,BTT270,BTT273]Manual [PDF]